arti/PersonalVotingMachine
1
0
Fork 0
mirror of https://github.com/Valeh2012/PersonalVotingMachine synced 2024-11-22 09:20:59 +02:00
Code Issues Projects Releases Wiki Activity
master
PersonalVotingMachine/basic-setup/components/u8g2/csrc/u8x8_d_uc1701_mini12864.c
valeh 26b0ba5954 first commit
2020-12-22 14:30:09 +02:00

206 lines
7.3 KiB
C
Raw Permalink Blame History

/*
u8x8_d_uc1701_mini12864.c (dealextreme, displays from ebay MP3 players)
Universal 8bit Graphics Library (https://github.com/olikraus/u8g2/)
Copyright (c) 2016, olikraus@gmail.com
All rights reserved.
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
* Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
* Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or other
materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#include "u8x8.h"
static const uint8_t u8x8_d_uc1701_mini12864_init_seq[] = {
U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */
U8X8_C(0x0e2), /* soft reset */
U8X8_C(0x0ae), /* display off */
U8X8_C(0x040), /* set display start line to 0 */
U8X8_C(0x0a0), /* ADC set to reverse */
U8X8_C(0x0c8), /* common output mode */
U8X8_C(0x0a6), /* display normal, bit val 0: LCD pixel off. */
U8X8_C(0x0a2), /* LCD bias 1/9 */
U8X8_C(0x02f), /* all power control circuits on */
U8X8_C(0x0f8), /* set booster ratio to */
U8X8_C(0x000), /* 4x */
U8X8_C(0x023), /* set V0 voltage resistor ratio to large */
U8X8_C(0x081), /* set contrast */
U8X8_C(0x027), /* contrast value */
U8X8_C(0x0ac), /* indicator */
// 0x000, /* disable */
U8X8_C(0x0ae), /* display off */
U8X8_C(0x0a5), /* enter powersafe: all pixel on, issue 142 */
U8X8_END_TRANSFER(), /* disable chip */
U8X8_END() /* end of sequence */
};
static const uint8_t u8x8_d_uc1701_mini12864_powersave0_seq[] = {
U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */
U8X8_C(0x0a4), /* all pixel off, issue 142 */
U8X8_C(0x0af), /* display on */
U8X8_END_TRANSFER(), /* disable chip */
U8X8_END() /* end of sequence */
};
static const uint8_t u8x8_d_uc1701_mini12864_powersave1_seq[] = {
U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */
U8X8_C(0x0ae), /* display off */
U8X8_C(0x0a5), /* enter powersafe: all pixel on, issue 142 */
U8X8_END_TRANSFER(), /* disable chip */
U8X8_END() /* end of sequence */
};
static const uint8_t u8x8_d_uc1701_mini12864_flip0_seq[] = {
U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */
U8X8_C(0x0a0), /* segment remap a0/a1*/
U8X8_C(0x0c8), /* c0: scan dir normal, c8: reverse */
U8X8_END_TRANSFER(), /* disable chip */
U8X8_END() /* end of sequence */
};
static const uint8_t u8x8_d_uc1701_mini12864_flip1_seq[] = {
U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */
U8X8_C(0x0a1), /* segment remap a0/a1*/
U8X8_C(0x0c0), /* c0: scan dir normal, c8: reverse */
U8X8_END_TRANSFER(), /* disable chip */
U8X8_END() /* end of sequence */
};
static const u8x8_display_info_t u8x8_uc1701_display_info =
{
/* chip_enable_level = */ 0,
/* chip_disable_level = */ 1,
/* post_chip_enable_wait_ns = */ 5,
/* pre_chip_disable_wait_ns = */ 5,
/* reset_pulse_width_ms = */ 1,
/* post_reset_wait_ms = */ 6,
/* sda_setup_time_ns = */ 12,
/* sck_pulse_width_ns = */ 75, /* half of cycle time (100ns according to datasheet), AVR: below 70: 8 MHz, >= 70 --> 4MHz clock */
/* sck_clock_hz = */ 4000000UL, /* since Arduino 1.6.0, the SPI bus speed in Hz. Should be 1000000000/sck_pulse_width_ns */
/* spi_mode = */ 0, /* active high, rising edge */
/* i2c_bus_clock_100kHz = */ 4,
/* data_setup_time_ns = */ 30,
/* write_pulse_width_ns = */ 40,
/* tile_width = */ 16, /* width of 16*8=128 pixel */
/* tile_hight = */ 8,
/* default_x_offset = */ 0,
/* flipmode_x_offset = */ 4,
/* pixel_width = */ 128,
/* pixel_height = */ 64
};
uint8_t u8x8_d_uc1701_mini12864(u8x8_t *u8x8, uint8_t msg, uint8_t arg_int, void *arg_ptr)
{
uint8_t x, c;
uint8_t *ptr;
switch(msg)
{
case U8X8_MSG_DISPLAY_SETUP_MEMORY:
u8x8_d_helper_display_setup_memory(u8x8, &u8x8_uc1701_display_info);
break;
case U8X8_MSG_DISPLAY_INIT:
u8x8_d_helper_display_init(u8x8);
u8x8_cad_SendSequence(u8x8, u8x8_d_uc1701_mini12864_init_seq);
break;
case U8X8_MSG_DISPLAY_SET_POWER_SAVE:
if ( arg_int == 0 )
u8x8_cad_SendSequence(u8x8, u8x8_d_uc1701_mini12864_powersave0_seq);
else
u8x8_cad_SendSequence(u8x8, u8x8_d_uc1701_mini12864_powersave1_seq);
break;
case U8X8_MSG_DISPLAY_SET_FLIP_MODE:
if ( arg_int == 0 )
{
u8x8_cad_SendSequence(u8x8, u8x8_d_uc1701_mini12864_flip0_seq);
u8x8->x_offset = u8x8->display_info->default_x_offset;
}
else
{
u8x8_cad_SendSequence(u8x8, u8x8_d_uc1701_mini12864_flip1_seq);
u8x8->x_offset = u8x8->display_info->flipmode_x_offset;
}
break;
#ifdef U8X8_WITH_SET_CONTRAST
case U8X8_MSG_DISPLAY_SET_CONTRAST:
u8x8_cad_StartTransfer(u8x8);
u8x8_cad_SendCmd(u8x8, 0x081 );
u8x8_cad_SendArg(u8x8, arg_int >> 2 ); /* uc1701 has range from 0 to 63 */
u8x8_cad_EndTransfer(u8x8);
break;
#endif
case U8X8_MSG_DISPLAY_DRAW_TILE:
u8x8_cad_StartTransfer(u8x8);
x = ((u8x8_tile_t *)arg_ptr)->x_pos;
x *= 8;
x += u8x8->x_offset;
u8x8_cad_SendCmd(u8x8, 0x010 | (x>>4) );
u8x8_cad_SendCmd(u8x8, 0x000 | ((x&15)));
u8x8_cad_SendCmd(u8x8, 0x0b0 | (((u8x8_tile_t *)arg_ptr)->y_pos));
c = ((u8x8_tile_t *)arg_ptr)->cnt;
c *= 8;
ptr = ((u8x8_tile_t *)arg_ptr)->tile_ptr;
/*
The following if condition checks the hardware limits of the uc1701
controller: It is not allowed to write beyond the display limits.
This is in fact an issue within flip mode.
bug: this check should be inside the while loop, see u8x8_d_pcd8544_84x48.c
*/
if ( c + x > 132u )
{
c = 132u;
c -= x;
}
do
{
u8x8_cad_SendData(u8x8, c, ptr); /* note: SendData can not handle more than 255 bytes */
arg_int--;
} while( arg_int > 0 );
u8x8_cad_EndTransfer(u8x8);
break;
default:
return 0;
}
return 1;
}
Reference in New Issue View Git Blame Copy Permalink