mirror of
https://github.com/Valeh2012/PersonalVotingMachine
synced 2024-11-26 02:40:59 +02:00
139 lines
4.3 KiB
C
139 lines
4.3 KiB
C
/* LED blink project for the STM32L031 */
|
||
|
||
#include "stm32l031xx.h"
|
||
|
||
/*===============================================*/
|
||
/*
|
||
systick IRQ
|
||
*/
|
||
volatile unsigned long SysTickCount = 0;
|
||
|
||
void __attribute__ ((interrupt, used)) SysTick_Handler(void)
|
||
{
|
||
SysTickCount++;
|
||
if ( SysTickCount & 1 )
|
||
GPIOA->BSRR = GPIO_BSRR_BS_13; /* atomic set PA13 */
|
||
else
|
||
GPIOA->BSRR = GPIO_BSRR_BR_13; /* atomic clr PA13 */
|
||
}
|
||
|
||
/*===============================================*/
|
||
/*
|
||
boost converter
|
||
PA6=Output to N-MOS Gate
|
||
PA7=Reference Input
|
||
*/
|
||
void boost_converter(void)
|
||
{
|
||
/* assumes, that SYSCFG_CRGR3 is not locked */
|
||
/* assumes, that COMP2 is not locked */
|
||
|
||
/* setup internal reference */
|
||
|
||
SYSCFG->CFGR3 |= SYSCFG_CFGR3_ENBUFLP_VREFINT_COMP; /* enable VREFINT during low power mode */
|
||
while( (SYSCFG->CFGR3 & SYSCFG_CFGR3_VREFINT_RDYF) == 0 ) /* wait for VREFINT until it becomes ready */
|
||
;
|
||
|
||
/* setup COMP2 */
|
||
|
||
/* select PA7 as positive input --> 101 */
|
||
COMP2->CSR &= ~(uint32_t)COMP_CSR_COMP2INPSEL;
|
||
COMP2->CSR |= COMP_CSR_COMP2INPSEL_0 | COMP_CSR_COMP2INPSEL_2;
|
||
|
||
/* select 1/4 internal reference voltage --> 0.306 Volt -->100 */
|
||
COMP2->CSR &= ~(uint32_t)COMP_CSR_COMP2INNSEL;
|
||
COMP2->CSR |= COMP_CSR_COMP2INNSEL_2;
|
||
|
||
/* invert polarity */
|
||
COMP2->CSR |= COMP_CSR_COMP2POLARITY;
|
||
|
||
/* comparator enable */
|
||
COMP2->CSR |= COMP_CSR_COMP2EN;
|
||
|
||
/* setup PWM mode for TIM22 */
|
||
|
||
/* configure output compare for channel 1 of TIM22 */
|
||
TIM22->CCMR1 &= ~(uint32_t)TIM_CCMR1_CC1S;
|
||
|
||
/* configure pwm mode 1 */
|
||
TIM22->CCMR1 &= ~(uint32_t)TIM_CCMR1_OC1M; /* clear mode to 000 */
|
||
TIM22->CCMR1 |= TIM_CCMR1_OC1M_2 | TIM_CCMR1_OC1M_1; /* pwm mode 1 (110) */
|
||
|
||
TIM22->CCMR1 |= TIM_CCMR1_OC1PE; /* load modified CCR1 during update event only */
|
||
|
||
TIM22->PSC = 0; /* run with max speed (2 MHz after reset) */
|
||
TIM22->ARR = 20; /* period of 20 clocks (100KHz if sys clock is not modified */
|
||
TIM22->CCR1 = 10; /* a value between 0 and ARR, which defines the duty cycle */
|
||
|
||
/* output the result of channel 1 to PA6 */
|
||
TIM22->CCER |= TIM_CCER_CC1E;
|
||
/* do not invert the output polarity (this is also the default value) */
|
||
TIM22->CCER &= ~(uint32_t)TIM_CCER_CC1P;
|
||
|
||
/* use up counter (this is also the default value) */
|
||
TIM22->CR1 &= ~(uint32_t)TIM_CR1_DIR;
|
||
|
||
/* do not use "one pulse mode" (continues mode, this is also the default value) */
|
||
TIM22->CR1 &= ~(uint32_t)TIM_CR1_OPM;
|
||
|
||
/* always generate an update event (this is also default) */
|
||
TIM22->CR1 &= ~(uint32_t)TIM_CR1_UDIS;
|
||
|
||
/* update event can be caused by UG bit and overflow (this is default) */
|
||
TIM22->CR1 &= ~(uint32_t)TIM_CR1_URS;
|
||
|
||
/* enable the counter */
|
||
TIM22->CR1 |= TIM_CR1_CEN;
|
||
|
||
|
||
|
||
|
||
TIMx->CR1 |= TIM_CR1_CEN; /* (6) */
|
||
TIMx->EGR |= TIM_EGR_UG; /* (7) */
|
||
|
||
/* setup gated mode for TIM22 */
|
||
|
||
|
||
/* (1) Configure channel 1 to detect low level on the TI1 input
|
||
by writing CC1S = ‘01’,
|
||
and configure the input filter duration by writing the IC1F[3:0]
|
||
bits
|
||
in the TIMx_CCMR1 register (if no filter is needed, keep
|
||
IC1F=0000).*/
|
||
/* (2) Select polarity by writing CC1P=1 in the TIMx_CCER register */
|
||
/* (3) Configure the timer in gated mode by writing SMS=101
|
||
Select TI1 as the trigger input source by writing TS=101
|
||
in the TIMx_SMCR register.*/
|
||
/* (4) Set prescaler to 4000-1 in order to get an increment each 250us */
|
||
/* (5) Enable the counter by writing CEN=1 in the TIMx_CR1 register. */
|
||
TIMx->CCMR1 |= TIM_CCMR1_CC1S_0; /* (1 */
|
||
TIMx->CCER |= TIM_CCER_CC1P; /* (2) */
|
||
TIMx->SMCR |= TIM_SMCR_SMS_2 | TIM_SMCR_SMS_0 \
|
||
| TIM_SMCR_TS_2 | TIM_SMCR_TS_0; /* (3) */
|
||
TIMx->PSC = 3999; /* (4) */
|
||
TIMx->CR1 |= TIM_CR1_CEN; /* (5) */
|
||
|
||
}
|
||
|
||
|
||
|
||
int main()
|
||
{
|
||
RCC->IOPENR |= RCC_IOPENR_IOPAEN; /* Enable clock for GPIO Port A */
|
||
__NOP();
|
||
__NOP();
|
||
GPIOA->MODER &= ~GPIO_MODER_MODE13; /* clear mode for PA13 */
|
||
GPIOA->MODER |= GPIO_MODER_MODE13_0; /* Output mode for PA13 */
|
||
GPIOA->OTYPER &= ~GPIO_OTYPER_OT_13; /* no Push/Pull for PA13 */
|
||
GPIOA->OSPEEDR &= ~GPIO_OSPEEDER_OSPEED13; /* low speed for PA13 */
|
||
GPIOA->PUPDR &= ~GPIO_PUPDR_PUPD13; /* no pullup/pulldown for PA13 */
|
||
GPIOA->BSRR = GPIO_BSRR_BR_13; /* atomic clr PA13 */
|
||
|
||
SysTick->LOAD = 2000*500 - 1;
|
||
SysTick->VAL = 0;
|
||
SysTick->CTRL = 7; /* enable, generate interrupt (SysTick_Handler), do not divide by 2 */
|
||
|
||
for(;;)
|
||
;
|
||
}
|