#ifndef MFRC522_h #define MFRC522_h #include typedef uint8_t bool; typedef uint8_t byte; typedef uint16_t word; // MFRC522 registers. Described in chapter 9 of the datasheet. // When using SPI all addresses are shifted one bit left in the "SPI address byte" (section 8.1.2.3) enum PCD_Register { // Page 0: Command and status // 0x00 // reserved for future use CommandReg = 0x01 << 1, // starts and stops command execution ComIEnReg = 0x02 << 1, // enable and disable interrupt request control bits DivIEnReg = 0x03 << 1, // enable and disable interrupt request control bits ComIrqReg = 0x04 << 1, // interrupt request bits DivIrqReg = 0x05 << 1, // interrupt request bits ErrorReg = 0x06 << 1, // error bits showing the error status of the last command executed Status1Reg = 0x07 << 1, // communication status bits Status2Reg = 0x08 << 1, // receiver and transmitter status bits FIFODataReg = 0x09 << 1, // input and output of 64 byte FIFO buffer FIFOLevelReg = 0x0A << 1, // number of bytes stored in the FIFO buffer WaterLevelReg = 0x0B << 1, // level for FIFO underflow and overflow warning ControlReg = 0x0C << 1, // miscellaneous control registers BitFramingReg = 0x0D << 1, // adjustments for bit-oriented frames CollReg = 0x0E << 1, // bit position of the first bit-collision detected on the RF interface // 0x0F // reserved for future use // Page 1:Command // 0x10 // reserved for future use ModeReg = 0x11 << 1, // defines general modes for transmitting and receiving TxModeReg = 0x12 << 1, // defines transmission data rate and framing RxModeReg = 0x13 << 1, // defines reception data rate and framing TxControlReg = 0x14 << 1, // controls the logical behavior of the antenna driver pins TX1 and TX2 TxASKReg = 0x15 << 1, // controls the setting of the transmission modulation TxSelReg = 0x16 << 1, // selects the internal sources for the antenna driver RxSelReg = 0x17 << 1, // selects internal receiver settings RxThresholdReg = 0x18 << 1, // selects thresholds for the bit decoder DemodReg = 0x19 << 1, // defines demodulator settings // 0x1A // reserved for future use // 0x1B // reserved for future use MfTxReg = 0x1C << 1, // controls some MIFARE communication transmit parameters MfRxReg = 0x1D << 1, // controls some MIFARE communication receive parameters // 0x1E // reserved for future use SerialSpeedReg = 0x1F << 1, // selects the speed of the serial UART interface // Page 2: Configuration // 0x20 // reserved for future use CRCResultRegH = 0x21 << 1, // shows the MSB and LSB values of the CRC calculation CRCResultRegL = 0x22 << 1, // 0x23 // reserved for future use ModWidthReg = 0x24 << 1, // controls the ModWidth setting? // 0x25 // reserved for future use RFCfgReg = 0x26 << 1, // configures the receiver gain GsNReg = 0x27 << 1, // selects the conductance of the antenna driver pins TX1 and TX2 for modulation CWGsPReg = 0x28 << 1, // defines the conductance of the p-driver output during periods of no modulation ModGsPReg = 0x29 << 1, // defines the conductance of the p-driver output during periods of modulation TModeReg = 0x2A << 1, // defines settings for the internal timer TPrescalerReg = 0x2B << 1, // the lower 8 bits of the TPrescaler value. The 4 high bits are in TModeReg. TReloadRegH = 0x2C << 1, // defines the 16-bit timer reload value TReloadRegL = 0x2D << 1, TCounterValueRegH = 0x2E << 1, // shows the 16-bit timer value TCounterValueRegL = 0x2F << 1, // Page 3:Test Registers // 0x30 // reserved for future use TestSel1Reg = 0x31 << 1, // general test signal configuration TestSel2Reg = 0x32 << 1, // general test signal configuration TestPinEnReg = 0x33 << 1, // enables pin output driver on pins D1 to D7 TestPinValueReg = 0x34 << 1, // defines the values for D1 to D7 when it is used as an I/O bus TestBusReg = 0x35 << 1, // shows the status of the internal test bus AutoTestReg = 0x36 << 1, // controls the digital self test VersionReg = 0x37 << 1, // shows the software version AnalogTestReg = 0x38 << 1, // controls the pins AUX1 and AUX2 TestDAC1Reg = 0x39 << 1, // defines the test value for TestDAC1 TestDAC2Reg = 0x3A << 1, // defines the test value for TestDAC2 TestADCReg = 0x3B << 1 // shows the value of ADC I and Q channels // 0x3C // reserved for production tests // 0x3D // reserved for production tests // 0x3E // reserved for production tests // 0x3F // reserved for production tests }; // MFRC522 comands. Described in chapter 10 of the datasheet. enum PCD_Command { PCD_Idle = 0x00, // no action, cancels current command execution PCD_Mem = 0x01, // stores 25 bytes into the internal buffer PCD_GenerateRandomID = 0x02, // generates a 10-byte random ID number PCD_CalcCRC = 0x03, // activates the CRC coprocessor or performs a self test PCD_Transmit = 0x04, // transmits data from the FIFO buffer PCD_NoCmdChange = 0x07, // no command change, can be used to modify the CommandReg register bits without affecting the command, for example, the PowerDown bit PCD_Receive = 0x08, // activates the receiver circuits PCD_Transceive = 0x0C, // transmits data from FIFO buffer to antenna and automatically activates the receiver after transmission PCD_MFAuthent = 0x0E, // performs the MIFARE standard authentication as a reader PCD_SoftReset = 0x0F // resets the MFRC522 }; // Commands sent to the PICC. enum PICC_Command { // The commands used by the PCD to manage communication with several PICCs (ISO 14443-3, Type A, section 6.4) PICC_CMD_REQA = 0x26, // REQuest command, Type A. Invites PICCs in state IDLE to go to READY and prepare for anticollision or selection. 7 bit frame. PICC_CMD_WUPA = 0x52, // Wake-UP command, Type A. Invites PICCs in state IDLE and HALT to go to READY(*) and prepare for anticollision or selection. 7 bit frame. PICC_CMD_CT = 0x88, // Cascade Tag. Not really a command, but used during anti collision. PICC_CMD_SEL_CL1 = 0x93, // Anti collision/Select, Cascade Level 1 PICC_CMD_SEL_CL2 = 0x95, // Anti collision/Select, Cascade Level 1 PICC_CMD_SEL_CL3 = 0x97, // Anti collision/Select, Cascade Level 1 PICC_CMD_HLTA = 0x50, // HaLT command, Type A. Instructs an ACTIVE PICC to go to state HALT. // The commands used for MIFARE Classic (from http://www.nxp.com/documents/data_sheet/MF1S503x.pdf, Section 9) // Use PCD_MFAuthent to authenticate access to a sector, then use these commands to read/write/modify the blocks on the sector. // The read/write commands can also be used for MIFARE Ultralight. PICC_CMD_MF_AUTH_KEY_A = 0x60, // Perform authentication with Key A PICC_CMD_MF_AUTH_KEY_B = 0x61, // Perform authentication with Key B PICC_CMD_MF_READ = 0x30, // Reads one 16 byte block from the authenticated sector of the PICC. Also used for MIFARE Ultralight. PICC_CMD_MF_WRITE = 0xA0, // Writes one 16 byte block to the authenticated sector of the PICC. Called "COMPATIBILITY WRITE" for MIFARE Ultralight. PICC_CMD_MF_DECREMENT = 0xC0, // Decrements the contents of a block and stores the result in the internal data register. PICC_CMD_MF_INCREMENT = 0xC1, // Increments the contents of a block and stores the result in the internal data register. PICC_CMD_MF_RESTORE = 0xC2, // Reads the contents of a block into the internal data register. PICC_CMD_MF_TRANSFER = 0xB0, // Writes the contents of the internal data register to a block. // The commands used for MIFARE Ultralight (from http://www.nxp.com/documents/data_sheet/MF0ICU1.pdf, Section 8.6) // The PICC_CMD_MF_READ and PICC_CMD_MF_WRITE can also be used for MIFARE Ultralight. PICC_CMD_UL_WRITE = 0xA2 // Writes one 4 byte page to the PICC. }; // MIFARE constants that does not fit anywhere else enum MIFARE_Misc { MF_ACK = 0xA, // The MIFARE Classic uses a 4 bit ACK/NAK. Any other value than 0xA is NAK. MF_KEY_SIZE = 6 // A Mifare Crypto1 key is 6 bytes. }; // PICC types we can detect. Remember to update PICC_GetTypeName() if you add more. enum PICC_Type { PICC_TYPE_UNKNOWN = 0, PICC_TYPE_ISO_14443_4 = 1, // PICC compliant with ISO/IEC 14443-4 PICC_TYPE_ISO_18092 = 2, // PICC compliant with ISO/IEC 18092 (NFC) PICC_TYPE_MIFARE_MINI = 3, // MIFARE Classic protocol, 320 bytes PICC_TYPE_MIFARE_1K = 4, // MIFARE Classic protocol, 1KB PICC_TYPE_MIFARE_4K = 5, // MIFARE Classic protocol, 4KB PICC_TYPE_MIFARE_UL = 6, // MIFARE Ultralight or Ultralight C PICC_TYPE_MIFARE_PLUS = 7, // MIFARE Plus PICC_TYPE_TNP3XXX = 8, // Only mentioned in NXP AN 10833 MIFARE Type Identification Procedure PICC_TYPE_NOT_COMPLETE = 255 // SAK indicates UID is not complete. }; // Return codes from the functions in this class. Remember to update GetStatusCodeName() if you add more. enum StatusCode { STATUS_OK = 1, // Success STATUS_ERROR = 2, // Error in communication STATUS_COLLISION = 3, // Collission detected STATUS_TIMEOUT = 4, // Timeout in communication. STATUS_NO_ROOM = 5, // A buffer is not big enough. STATUS_INTERNAL_ERROR = 6, // Internal error in the code. Should not happen ;-) STATUS_INVALID = 7, // Invalid argument. STATUS_CRC_WRONG = 8, // The CRC_A does not match STATUS_MIFARE_NACK = 9 // A MIFARE PICC responded with NAK. }; // A struct used for passing the UID of a PICC. typedef struct { byte size; // Number of bytes in the UID. 4, 7 or 10. byte uidByte[10]; byte sak; // The SAK (Select acknowledge) byte returned from the PICC after successful selection. } Uid; // A struct used for passing a MIFARE Crypto1 key typedef struct { byte keyByte[MF_KEY_SIZE]; } MIFARE_Key; // Member variables //Uid uid; // Used by PICC_ReadCardSerial(). // Size of the MFRC522 FIFO //static const byte FIFO_SIZE = 64; // The FIFO is 64 bytes. //----------------------------------------------------------------------------------- // Functions for setting up the Arduino //----------------------------------------------------------------------------------- void MFRC522_init(void); void setSPIConfig(void); //----------------------------------------------------------------------------------- // Basic interface functions for communicating with the MFRC522 //----------------------------------------------------------------------------------- void PCD_WriteRegister(byte reg, byte value); void PCD_WriteRegister2(byte reg, byte count, byte *values); byte PCD_ReadRegister(byte reg); void PCD_ReadRegister2(byte reg, byte count, byte *values, byte rxAlign); void setBitMask(unsigned char reg, unsigned char mask); void PCD_SetRegisterBitMask(byte reg, byte mask); void PCD_ClearRegisterBitMask(byte reg, byte mask); byte PCD_CalculateCRC(byte *data, byte length, byte *result); //----------------------------------------------------------------------------------- // Functions for manipulating the MFRC522 //----------------------------------------------------------------------------------- byte PCD_Init(void); byte PCD_Reset(void); void PCD_AntennaOn(void); //----------------------------------------------------------------------------------- // Functions for communicating with PICCs //----------------------------------------------------------------------------------- byte PCD_TransceiveData(byte *sendData, byte sendLen, byte *backData, byte *backLen, byte *validBits, byte rxAlign, bool checkCRC); byte PCD_CommunicateWithPICC(byte command, byte waitIRq, byte *sendData, byte sendLen, byte *backData, byte *backLen, byte *validBits, byte rxAlign, bool checkCRC); byte PICC_RequestA(byte *bufferATQA, byte *bufferSize); byte PICC_WakeupA(byte *bufferATQA, byte *bufferSize); byte PICC_REQA_or_WUPA( byte command, byte *bufferATQA, byte *bufferSize); byte PICC_Select(Uid *uid, byte validBits); byte PICC_HaltA(void); //----------------------------------------------------------------------------------- // Functions for communicating with MIFARE PICCs //----------------------------------------------------------------------------------- byte PCD_Authenticate(byte command, byte blockAddr, MIFARE_Key *key, Uid *uid); void PCD_StopCrypto1(void); byte MIFARE_Read(byte blockAddr, byte *buffer, byte *bufferSize); byte MIFARE_Write(byte blockAddr, byte *buffer, byte bufferSize); byte MIFARE_Decrement(byte blockAddr, long delta); byte MIFARE_Increment(byte blockAddr, long delta); byte MIFARE_Restore(byte blockAddr); byte MIFARE_Transfer(byte blockAddr); byte MIFARE_Ultralight_Write(byte page, byte *buffer, byte bufferSize); //----------------------------------------------------------------------------------- // Support functions //----------------------------------------------------------------------------------- byte PCD_MIFARE_Transceive( byte *sendData, byte sendLen, bool acceptTimeout); const char *GetStatusCodeName(byte code); byte PICC_GetType(byte sak); const char *PICC_GetTypeName(byte type); void PICC_DumpToSerial(Uid *uid); void PICC_DumpMifareClassicToSerial(Uid *uid, byte piccType, MIFARE_Key *key); void PICC_DumpMifareClassicSectorToSerial(Uid *uid, MIFARE_Key *key, byte sector); void PICC_DumpMifareUltralightToSerial(void); void MIFARE_SetAccessBits(byte *accessBitBuffer, byte g0, byte g1, byte g2, byte g3); //----------------------------------------------------------------------------------- // Convenience functions - does not add extra functionality //----------------------------------------------------------------------------------- bool PICC_IsNewCardPresent(void); bool PICC_ReadCardSerial(Uid* uid); /* private: byte _chipSelectPin; // Arduino pin connected to MFRC522's SPI slave select input (Pin 24, NSS, active low) byte _resetPowerDownPin; // Arduino pin connected to MFRC522's reset and power down input (Pin 6, NRSTPD, active low) byte MIFARE_TwoStepHelper(byte command, byte blockAddr, long data); */ #endif