1
0
mirror of git://projects.qi-hardware.com/antorcha.git synced 2024-12-24 03:18:59 +02:00
antorcha/NOTES

96 lines
2.9 KiB
Plaintext
Raw Normal View History

design specs:
- text readable at up to 50 m
- automatic centering of image
- non-aggressive design
- suitable for dim ambient light, such as an illuminated street
at night
- powered by off-the shelf batteries
- content programmable via wireless interface
- use medium-strength authentication for wireless communication
opportunistic component selection:
- reuse ben-wpan (IEEE 802.15.4) circuit, and ben+atben or
laptop+atusb for (remote) editing
- use ATmega 48/88/168 series controller
- use ADXL321 series acceleration sensor
- use APTD1608SEC LEDs
- use unregulated battery power
visible field:
- height: ~25 cm, with 16 pairs of LEDs, at 8 mm spacing
- horizontal movement (arm waving) is about 120 cm
- this yields up to 80 horizontal square "pixels"
- text capacity
height width gap character (per line)
16 px 10 px 2 px 6.8
7 px 5 px 2 px 11.7
7 px 5 px 1 px 13.5
- text height
pixels cm
16 24
7 11.2
physical structure:
- mount LEDs on stick
- batteries and main circuit in handle or extension (see below)
- make stick strong enough to resist excessive bending/breaking
under wind load
- make stick as weak as possible to avoid perception or use as
weapon
stick length:
- LEDs occupy (16*2-1)*8 mm plus component width, in total
roughly 249 mm
- add 2 cm for termination at top
- add extension for increased visibility
extension:
- assume small spectators are 10 cm smaller than nearby
obstacles (e.g., shoulders of tall people)
- assume distance between spectators is 80 cm
- to be visible at 50 m, the bottom edge must therefore be
50 m / 80 cm * (10 cm / 80 cm) * 10 cm = 78 cm
above eye level of small spectators
- assume waver to be about 20 cm taller than small spectator
- hand above head position yields distance of about 30 cm
above eye level
- therefore, extension should be 78 cm - 50 cm = 28 cm
handle design:
- about 10-12 cm in length
- include button for control functions. button can be located
on extension
- acceleration sensor should be at a high position, possibly
on extension
overall length:
- 25 cm for LEDs
- 2 cm for termination (head)
- 28 cm for extension
- 12 cm for handle
- 67 cm total length
electrical, LEDs:
- no multiplexing
- max. 30 mA per LED pair (series)
-> max. 16 * 30 mA = 480 mA for LEDs
- series resistor is 56 Ohm. Allow up to additional 10% voltage drop
in trace.
-> Rmax per LED pair is ~ 5 Ohm
- assume 30 cm trace
- variant A: switching transistors at LED
- average length is 15 cm
- Rmax is 5 Ohm / 16 = 300 mOhm
- http://circuitcalculator.com/wordpress/2006/01/31/pcb-trace-width-calculator/
yields for 500 mA at 2 oz/ft2:
- minimum width 2.3 mil / 0.06 mm
- 111 mOhm
=> 8 mil traces are more than sufficient, even for power rails
- variant B: switching transistors in handle
even less demanding
authentication:
- shared secret (128 bit, MD5-hashed text with 128 bit salt)
- salt (128 bit)
- MD5