mirror of
git://projects.qi-hardware.com/ben-wpan.git
synced 2024-11-24 23:43:08 +02:00
prod/doc/analysis.html: more material on checking the supply voltages
This commit is contained in:
parent
dc40ff60a6
commit
47b710dcb1
@ -15,6 +15,70 @@
|
||||
|
||||
<H2>Supply voltages</H2>
|
||||
|
||||
The transceiver has three voltage domains:
|
||||
<UL>
|
||||
<LI>The supply and I/O voltage, which is nominally 3.3 V in
|
||||
<B>atben</B> and <B>atusb</B>,
|
||||
<LI>the digital (core) supply, which is nominally 1.8 V, and
|
||||
<LI>the analog (RF) supply, which is nominally 1.8 V.
|
||||
</UL>
|
||||
<BR>
|
||||
On <B>atusb</B>, there is also the USB voltage domain at nominally 5.0 V.
|
||||
<P>
|
||||
Voltages should be tested in the following order: USB, then I/O, then
|
||||
digital, and finally analog. The table below gives the permissible
|
||||
ranges. Any voltages outside of these ranges indicate a problem.
|
||||
<P>
|
||||
<TABLE>
|
||||
<TR><TH>Domain<TH>Nominal<TH>Minimum<TH>Maximum
|
||||
<TR><TD>USB<TD>5.0 V<TD>4.5 V<TD>5.25 V
|
||||
<TR><TD>I/O<TD>3.3 V<TD>3.0 V<TD>3.6 V
|
||||
<TR><TD>Digital<TD>1.8 V<TD>1.7 V<TD>1.9 V
|
||||
<TR><TD>Analog<TD>1.8 V<TD>1.7 V<TD>1.9 V
|
||||
</TABLE>
|
||||
<P>
|
||||
|
||||
<H3>Measurement setup</H3>
|
||||
|
||||
The measurements should be performed either with a digital multimeter.
|
||||
To enable all voltage domains, put the transceiver in receive mode:
|
||||
<PRE>
|
||||
atrf-txrx
|
||||
</PRE>
|
||||
or
|
||||
<PRE>
|
||||
atrf-txrx -d net:ben
|
||||
</PRE>
|
||||
Exit with Ctrl-C.
|
||||
<P>
|
||||
To produce periodic transmissions in addition to enabling all voltage
|
||||
domains, use
|
||||
<PRE>
|
||||
atrf-txrx -p 3 -E 0
|
||||
</PRE>
|
||||
or
|
||||
<PRE>
|
||||
atrf-txrx -d net:ben -p 3 -E 0
|
||||
</PRE>
|
||||
Again, exit with Ctrl-C. Note that the transmissions may disturb nearby
|
||||
equipment operating in the 2.4 GHz band, such as 802.11 networks. This
|
||||
can be prevented by shorting the antenna to ground.
|
||||
<P>
|
||||
In case the board does not accept commands, only the USB and I/O voltage
|
||||
can be checked. If they are correct, proceed with checking the clock.
|
||||
|
||||
|
||||
<!-- ---------------------------------------------------------------------- -->
|
||||
|
||||
|
||||
<H3>Measurement points on atben</H3>
|
||||
|
||||
|
||||
<!-- ---------------------------------------------------------------------- -->
|
||||
|
||||
|
||||
<H3>Measurement points on atusb</H3>
|
||||
|
||||
|
||||
<!-- ====================================================================== -->
|
||||
|
||||
|
Loading…
Reference in New Issue
Block a user