diff --git a/atusb/fw/Makefile b/atusb/fw/Makefile
index 4cc749c..c79cb26 100644
--- a/atusb/fw/Makefile
+++ b/atusb/fw/Makefile
@@ -26,6 +26,9 @@ endif
 ifeq ($(NAME),rzusb)
 CHIP=at90usb1287
 CFLAGS += -DRZUSB -DAT86RF230
+else ifeq ($(NAME),hulusb)
+CHIP=at90usb1287
+CFLAGS += -DHULUSB -DAT86RF212
 else
 CHIP=atmega32u2
 CFLAGS += -DATUSB -DAT86RF231
@@ -58,6 +61,9 @@ endif
 ifeq ($(NAME),rzusb)
 OBJS += board_rzusb.o
 BOOT_OBJS += board_rzusb.o
+else ifeq ($(NAME),hulusb)
+OBJS += board_hulusb.o
+BOOT_OBJS += board_hulusb.o
 else
 OBJS += board_atusb.o
 BOOT_OBJS += board_atusb.o
diff --git a/atusb/fw/board.c b/atusb/fw/board.c
index 8567589..c3b8d26 100644
--- a/atusb/fw/board.c
+++ b/atusb/fw/board.c
@@ -29,45 +29,63 @@
 
 uint8_t board_sernum[42] = { 42, USB_DT_STRING };
 
-void reset_rf(void)
+/* ----- Register access --------------------------------------------------- */
+
+void change_state(uint8_t new)
 {
-	/* set up all the outputs; default port value is 0 */
-
-	DDRB = 0;
-	DDRC = 0;
-	DDRD = 0;
-	PORTB = 0;
-	PORTC = 0;
-	PORTD = 0;
-
-	OUT(LED);
-	OUT(nRST_RF);   /* this also resets the transceiver */
-	OUT(SLP_TR);
-
-	spi_init();
-
-	/* AT86RF231 data sheet, 12.4.13, reset pulse width: 625 ns (min) */
-
-	CLR(nRST_RF);
-	_delay_us(2);
-	SET(nRST_RF);
-
-	/* 12.4.14: SPI access latency after reset: 625 ns (min) */
-
-	_delay_us(2);
-
-	/* we must restore TRX_CTRL_0 after each reset (9.6.4) */
-
-	set_clkm();
+	while ((reg_read(REG_TRX_STATUS) & TRX_STATUS_MASK) ==
+		TRX_STATUS_TRANSITION);
+	reg_write(REG_TRX_STATE, new);
 }
 
 
-void led(bool on)
+uint8_t reg_read(uint8_t reg)
 {
-	if (on)
-		SET(LED);
-	else
-		CLR(LED);
+	uint8_t value;
+
+	spi_begin();
+	spi_send(AT86RF230_REG_READ | reg);
+	value = spi_recv();
+	spi_end();
+
+	return value;
+}
+
+
+uint8_t subreg_read(uint8_t address, uint8_t mask, uint8_t position)
+{
+	/* Read current register value and mask out subregister. */
+	uint8_t register_value = reg_read(address);
+	register_value &= mask;
+	register_value >>= position; /* Align subregister value. */
+
+	return register_value;
+}
+
+
+void reg_write(uint8_t reg, uint8_t value)
+{
+	spi_begin();
+	spi_send(AT86RF230_REG_WRITE | reg);
+	spi_send(value);
+	spi_end();
+}
+
+
+void subreg_write(uint8_t address, uint8_t mask, uint8_t position, uint8_t value)
+{
+	/* Read current register value and mask area outside the subregister. */
+	uint8_t register_value = reg_read(address);
+	register_value &= ~mask;
+
+	/* Start preparing the new subregister value. shift in place and mask. */
+	value <<= position;
+	value &= mask;
+
+	value |= register_value; /* Set the new subregister value. */
+
+	/* Write the modified register value. */
+	reg_write(address, value);
 }
 
 
diff --git a/atusb/fw/board.h b/atusb/fw/board.h
index 78a9065..dbcd410 100644
--- a/atusb/fw/board.h
+++ b/atusb/fw/board.h
@@ -24,6 +24,9 @@
 #ifdef RZUSB
 #include "board_rzusb.h"
 #endif
+#ifdef HULUSB
+#include "board_hulusb.h"
+#endif
 
 #define	SET_2(p, b)	PORT##p |= 1 << (b)
 #define	CLR_2(p, b)	PORT##p &= ~(1 << (b))
@@ -83,4 +86,10 @@ void get_sernum(void);
 
 void board_app_init(void);
 
+uint8_t reg_read(uint8_t reg);
+uint8_t subreg_read(uint8_t address, uint8_t mask, uint8_t position);
+void reg_write(uint8_t reg, uint8_t value);
+void subreg_write(uint8_t address, uint8_t mask, uint8_t position, uint8_t value);
+void change_state(uint8_t new);
+
 #endif /* !BOARD_H */
diff --git a/atusb/fw/board_app.c b/atusb/fw/board_app.c
index 815f4da..1fa9bf4 100644
--- a/atusb/fw/board_app.c
+++ b/atusb/fw/board_app.c
@@ -154,7 +154,7 @@ static void done(void *user)
 
 uint8_t irq_serial;
 
-#ifdef ATUSB
+#if defined(ATUSB) || defined(HULUSB)
 ISR(INT0_vect)
 #endif
 #ifdef RZUSB
diff --git a/atusb/fw/board_atusb.c b/atusb/fw/board_atusb.c
index 518fe78..a02fb7f 100644
--- a/atusb/fw/board_atusb.c
+++ b/atusb/fw/board_atusb.c
@@ -29,6 +29,46 @@
 
 static bool spi_initialized = 0;
 
+void reset_rf(void)
+{
+	/* set up all the outputs; default port value is 0 */
+
+	DDRB = 0;
+	DDRC = 0;
+	DDRD = 0;
+	PORTB = 0;
+	PORTC = 0;
+	PORTD = 0;
+
+	OUT(LED);
+	OUT(nRST_RF);   /* this also resets the transceiver */
+	OUT(SLP_TR);
+
+	spi_init();
+
+	/* AT86RF231 data sheet, 12.4.13, reset pulse width: 625 ns (min) */
+
+	CLR(nRST_RF);
+	_delay_us(2);
+	SET(nRST_RF);
+
+	/* 12.4.14: SPI access latency after reset: 625 ns (min) */
+
+	_delay_us(2);
+
+	/* we must restore TRX_CTRL_0 after each reset (9.6.4) */
+
+	set_clkm();
+}
+
+void led(bool on)
+{
+	if (on)
+		SET(LED);
+	else
+		CLR(LED);
+}
+
 void set_clkm(void)
 {
 	/* switch CLKM to 8 MHz */
diff --git a/atusb/fw/board_hulusb.c b/atusb/fw/board_hulusb.c
new file mode 100644
index 0000000..084714e
--- /dev/null
+++ b/atusb/fw/board_hulusb.c
@@ -0,0 +1,179 @@
+/*
+ * fw/board_hulusb.c - Busware HUL Board-specific functions (for boot loader and application)
+ *
+ * Written 2017 by Filzmaier Josef
+ * Based on fw/board_rzusb written and Copyright 2016 Stefan Schmidt
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+
+#include <stdbool.h>
+#include <stdint.h>
+
+#include <avr/io.h>
+#include <avr/interrupt.h>
+#include <avr/boot.h>
+
+#define F_CPU   8000000UL
+#include <util/delay.h>
+
+#include "usb.h"
+#include "at86rf230.h"
+#include "board.h"
+#include "spi.h"
+#include "usb/usb.h"
+
+static bool spi_initialized = 0;
+
+void reset_rf(void)
+{
+	/* set up all the outputs; default port value is 0 */
+
+	DDRB = 0;
+	DDRC = 0;
+	DDRD = 0;
+	PORTB = 0;
+	PORTC = 0;
+	PORTD = 0;
+
+	OUT(LED_RED);
+	OUT(LED_GREEN);
+	SET(LED_RED); /* Leds are active low on HULUSB board */
+	CLR(LED_GREEN); /* Green Led indicates the dongle is running */
+	OUT(nRST_RF);   /* this also resets the transceiver */
+	OUT(SLP_TR);
+
+	spi_init();
+
+	/* AT86RF212 data sheet, Appendix B, p166 Power-On Reset procedure */
+	/*-----------------------------------------------------------------*/
+	CLR(SLP_TR);
+	SET(nRST_RF);
+	SET(nSS);
+	_delay_us(400);
+
+	CLR(nRST_RF);
+	_delay_us(2);
+	SET(nRST_RF);
+
+	/* 5.1.4.5: Wait t10: 625 ns (min) */
+
+	_delay_us(2);
+
+	reg_write(REG_TRX_CTRL_0, 0x19);
+
+	change_state(TRX_CMD_FORCE_TRX_OFF);
+	/*-----------------------------------------------------------------*/
+
+	/* we must restore TRX_CTRL_0 after each reset (7.7.4) */
+
+	set_clkm();
+}
+
+void led_red(bool on) {
+	if (on)
+		CLR(LED_RED);
+	else
+		SET(LED_RED);
+}
+
+void led_green(bool on) {
+	if (on)
+		CLR(LED_GREEN);
+	else
+		SET(LED_GREEN);
+}
+
+void led(bool on)
+{
+	led_red(on);
+}
+
+void set_clkm(void)
+{
+	/* CLKM is not connected on BUSWARE HUL and therefore it is running in
+	 * async mode. */
+	reg_write(REG_TRX_CTRL_0, 0x00);
+
+	/* TX_AUTO_CRC_ON, default disabled */
+	subreg_write(SR_TX_AUTO_CRC_ON, 1);
+}
+
+void board_init(void)
+{
+	/* Disable the watchdog timer */
+
+	MCUSR = 0;		/* Remove override */
+	WDTCSR |= 1 << WDCE;	/* Enable change */
+	WDTCSR = 1 << WDCE;	/* Disable watchdog while still enabling
+	change */
+
+	CLKPR = 1 << CLKPCE;
+	/* We start with a 16 MHz/8 clock. Put the prescaler to 2. */
+	CLKPR = 1 << CLKPS0;
+
+	get_sernum();
+}
+
+void spi_begin(void)
+{
+	if (!spi_initialized)
+		spi_init();
+	CLR(nSS);
+}
+
+void spi_off(void)
+{
+	spi_initialized = 0;
+	SPCR &= ~(1 << SPE);
+}
+
+void spi_init(void)
+{
+	SET(nSS);
+	OUT(SCLK);
+	OUT(MOSI);
+	OUT(nSS);
+	IN(MISO);
+
+	SPCR = (1 << SPE) | (1 << MSTR);
+	SPSR = (1 << SPI2X);
+
+	spi_initialized = 1;
+}
+
+void usb_init(void)
+{
+	USBCON |= 1 << FRZCLK;		/* freeze the clock */
+
+	/* enable the PLL and wait for it to lock */
+	/* TODO sheet page 50 For Atmel AT90USB128x only. Do not use with Atmel AT90USB64x. */
+	/*  FOR 8 XTAL Mhz only!!! */
+	PLLCSR = ((1 << PLLP1) | (1 << PLLP0));
+	PLLCSR |= 1 << PLLE;
+	while (!(PLLCSR & (1 << PLOCK)));
+
+	UHWCON |= (1 << UVREGE);
+
+	USBCON &= ~((1 << USBE) | (1 << OTGPADE));		/* reset the controller */
+	USBCON |= ((1 << USBE) | (1 << OTGPADE));
+
+	USBCON &= ~(1 << FRZCLK);	/* thaw the clock */
+
+	UDCON &= ~(1 << DETACH);	/* attach the pull-up */
+	UDIEN = 1 << EORSTE;		/* enable device interrupts  */
+	//	UDCON |= 1 << RSTCPU;		/* reset CPU on bus reset */
+
+	ep_init();
+}
+
+void board_app_init(void)
+{
+	/* enable INT0, trigger on rising edge */
+	EICRA = 1 << ISC01 | 1 << ISC00;
+	EIMSK = 1 << INT0;
+}
diff --git a/atusb/fw/board_hulusb.h b/atusb/fw/board_hulusb.h
new file mode 100644
index 0000000..a1dadf0
--- /dev/null
+++ b/atusb/fw/board_hulusb.h
@@ -0,0 +1,66 @@
+/*
+ * fw/board_hulusb.h - Busware HUL Board-specific functions (for boot loader and application)
+ *
+ * Written 2017 by Filzmaier Josef
+ * Based on fw/board_rzusb written and Copyright 2016 Stefan Schmidt
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef BOARD_HULUSB_H
+#define	BOARD_HULUSB_H
+
+#include <stdbool.h>
+#include <stdint.h>
+
+#define LED_RED_PORT		A
+#define LED_GREEN_PORT		A
+#define LED_RED_BIT		3
+#define LED_GREEN_BIT 		4
+#define LED_PORT		LED_RED_PORT
+#define LED_BIT		  	LED_RED_BIT
+
+#define nRST_RF_PORT		B
+#define nRST_RF_BIT	  	5
+#define SLP_TR_PORT		B
+#define SLP_TR_BIT	  	4
+
+#define SCLK_PORT		B
+#define SCLK_BIT	  	1
+#define MOSI_PORT		B
+#define MOSI_BIT	  	2
+
+#define MISO_PORT		B
+#define MISO_BIT	  	3
+#define nSS_PORT		B
+#define nSS_BIT		  	0
+#define IRQ_RF_PORT		D
+#define IRQ_RF_BIT	  	4
+
+#define SR_TX_AUTO_CRC_ON	0x04, 0x20, 5
+#define SR_CHANNEL		0x08, 0x1f, 0
+
+#define RG_CC_CTRL_1		(0x14)
+
+#define SPI_WAIT_DONE()	while ((SPSR & (1 << SPIF)) == 0)
+#define SPI_DATA	SPDR
+
+void set_clkm(void);
+void board_init(void);
+
+void led_red(bool on);
+void led_green(bool on);
+
+void spi_begin(void);
+void spi_off(void);
+void spi_init(void);
+
+#ifdef DEBUG
+void printStatus(void);
+#define PRINT_STATUS() printStatus()
+#endif
+
+#endif /* !BOARD_HULUSB_H */
diff --git a/atusb/fw/board_rzusb.c b/atusb/fw/board_rzusb.c
index 83333f8..e83d6fa 100644
--- a/atusb/fw/board_rzusb.c
+++ b/atusb/fw/board_rzusb.c
@@ -29,6 +29,46 @@
 
 static bool spi_initialized = 0;
 
+void reset_rf(void)
+{
+	/* set up all the outputs; default port value is 0 */
+
+	DDRB = 0;
+	DDRC = 0;
+	DDRD = 0;
+	PORTB = 0;
+	PORTC = 0;
+	PORTD = 0;
+
+	OUT(LED);
+	OUT(nRST_RF);   /* this also resets the transceiver */
+	OUT(SLP_TR);
+
+	spi_init();
+
+	/* AT86RF231 data sheet, 12.4.13, reset pulse width: 625 ns (min) */
+
+	CLR(nRST_RF);
+	_delay_us(2);
+	SET(nRST_RF);
+
+	/* 12.4.14: SPI access latency after reset: 625 ns (min) */
+
+	_delay_us(2);
+
+	/* we must restore TRX_CTRL_0 after each reset (9.6.4) */
+
+	set_clkm();
+}
+
+void led(bool on)
+{
+	if (on)
+		SET(LED);
+	else
+		CLR(LED);
+}
+
 void set_clkm(void)
 {
 	/* switch CLKM to 8 MHz */
diff --git a/atusb/fw/ep0.c b/atusb/fw/ep0.c
index 674f9de..fa43f3b 100644
--- a/atusb/fw/ep0.c
+++ b/atusb/fw/ep0.c
@@ -38,11 +38,15 @@
 #include "mac.h"
 
 #ifdef ATUSB
-#define	HW_TYPE		HW_TYPE_110131
+#define	HW_TYPE		ATUSB_HW_TYPE_110131
 #endif
 
 #ifdef RZUSB
-#define	HW_TYPE		HW_TYPE_RZUSB
+#define	HW_TYPE		ATUSB_HW_TYPE_RZUSB
+#endif
+
+#ifdef HULUSB
+#define HW_TYPE		ATUSB_HW_TYPE_HULUSB
 #endif
 
 #ifdef DEBUG
diff --git a/atusb/fw/include/atusb/atusb.h b/atusb/fw/include/atusb/atusb.h
index b22bbaa..555d14b 100644
--- a/atusb/fw/include/atusb/atusb.h
+++ b/atusb/fw/include/atusb/atusb.h
@@ -50,6 +50,14 @@ enum atusb_requests {
 	ATUSB_EUI64_READ,
 };
 
+enum {
+	ATUSB_HW_TYPE_100813,	/* 2010-08-13 */
+	ATUSB_HW_TYPE_101216,	/* 2010-12-16 */
+	ATUSB_HW_TYPE_110131,	/* 2011-01-31, ATmega32U2-based */
+	ATUSB_HW_TYPE_RZUSB,	/* Atmel Raven USB dongle with at86rf230 */
+	ATUSB_HW_TYPE_HULUSB,	/* Busware HUL USB dongle with at86rf212 */
+};
+
 /*
  * Direction	bRequest		wValue		wIndex	wLength
  *
diff --git a/atusb/fw/include/atusb/ep0.h b/atusb/fw/include/atusb/ep0.h
index dd76d8d..7777345 100644
--- a/atusb/fw/include/atusb/ep0.h
+++ b/atusb/fw/include/atusb/ep0.h
@@ -32,11 +32,6 @@
 #define EP0ATUSB_MAJOR	0	/* EP0 protocol, major revision */
 #define EP0ATUSB_MINOR	3	/* EP0 protocol, minor revision */
 
-#define	HW_TYPE_100813	0	/* 2010-08-13 */
-#define	HW_TYPE_101216	1	/* 2010-12-16 */
-#define	HW_TYPE_110131	2	/* 2011-01-31, ATmega32U2-based */
-#define	HW_TYPE_RZUSB	3	/* Atmel Raven USB dongle with at86rf230 */
-
 
 /*
  * bmRequestType:
diff --git a/atusb/fw/mac.c b/atusb/fw/mac.c
index 265d542..835002c 100644
--- a/atusb/fw/mac.c
+++ b/atusb/fw/mac.c
@@ -47,31 +47,6 @@ static inline void next_buf(uint8_t *index)
 }
 
 
-/* ----- Register access --------------------------------------------------- */
-
-
-static uint8_t reg_read(uint8_t reg)
-{
-	uint8_t value;
-
-	spi_begin();
-	spi_send(AT86RF230_REG_READ | reg);
-	value = spi_recv();
-	spi_end();
-
-	return value;
-}
-
-
-static void reg_write(uint8_t reg, uint8_t value)
-{
-	spi_begin();
-	spi_send(AT86RF230_REG_WRITE | reg);
-	spi_send(value);
-	spi_end();
-}
-
-
 /* ----- Interrupt handling ------------------------------------------------ */
 
 
@@ -101,13 +76,6 @@ static void tx_ack_done(void *user)
 	usb_next();
 }
 
-static void change_state(uint8_t new)
-{
-	while ((reg_read(REG_TRX_STATUS) & TRX_STATUS_MASK) ==
-	    TRX_STATUS_TRANSITION);
-	reg_write(REG_TRX_STATE, new);
-}
-
 static void rx_done(void *user)
 {
 	led(0);
@@ -223,6 +191,14 @@ static void do_tx(void *user)
 	 */
 	reg_write(REG_TRX_STATE, TRX_CMD_PLL_ON);
 #endif
+#ifdef AT86RF212
+	/*
+	* We use TRX_CMD_FORCE_PLL_ON instead of TRX_CMD_PLL_ON because a new
+	* reception may have begun while we were still working on the previous
+	* one.
+	*/
+	reg_write(REG_TRX_STATE, TRX_CMD_FORCE_PLL_ON);
+#endif
 
 	handle_irq();