- atusb.brd: moved C14 and adjacent via 10 mil away from the transceive,
for improved solderability
- atusb.brd: moved nRST_RF via and trace by 5 mil, for better access to
the trace
- atusb.brd: reduced crystal front ground zone such that it does not
creep under XTAL2 corner (where it might meet exposed metal)
- usb.sch: cleaned up programming/auxiliary/LED signals
- usb.sch: swapped LED and nRST_RF (tracking the layout)
- atusb.brd: updated for corrected netlist
- atusb.brd: moved date code which overlapped with traces
- atusb.brd: reduced front RF and power ground zones to avoid ground
fill between transceiver pads
- atusb.brd: added ground traces around crystal to widen ground zone
- atusb.pro, atusb.cmp: updated for ATmega32U2-based design
- usb.sch: rearranged LED, nRST_RF, and SLP_TR, to make layout easier
- atusb.brd: redid layout for the ATmega32U2-based design
Settings according to
http://www.nxp.com/documents/mounting_and_soldering/AN10365.pdf
- atben.pro, atben.brd, atusb.pro, atusb.brd: set solder mask clearance
to 50 um (copper-defined pads)
- atben.pro, atben.brd, atusb.pro, atusb.brd: set solder paste clearance
to 25 um
- atusb.brd: moved component references for proper printing on silk screen
- atusb.brd: moved component values for easy display (do not print on
silk screen !)
- atusb.brd, atusb.cmp: changed all 0402-M to the new 0402
- atusb.brd, atusb.cmp: changed 0603-M to the new 0603
- atusb.brd: updated layout for component changes
- atrf.sch: replaced the AT86RF230 with the AT86RF231
- atusb.sch, usb.sch, atrf.sch: removed TST signal
- atrf.sch: grounded former TST pin
- atusb.brd: updated for TST removal
- atusb.brd: increased space between SLP_TR and nRST_RF vias
- atusb.brd: connect U2 pin 6 to ground pad
- atusb.sch, usb.sch, atrf.sch, atusb.brd: changed version to 20110104
- atusb.brd: increased RF ground zone by 150 mil in an attempt to reduce
interferences between the the antenna and the rest of the circuit
- atusb.brd: added more vias around and inside the RF ground zone
- atusb.brd: set version to 20110102
Traces leaving a pad on the side may invite solder bridges to "false pads"
exposed at the edges of the chip, with unknown consequences.
- atusb.brd: make trace from P0.0 (IRQ_RF) leave pad at the front, not
at the side
- atusb.brd: make trave from P0.7 (SCLK) leave pad at front, not at the
side
- atusb.brd: nRST may need an external pull-up to VDD. Added via to bring
nRST and VDD within reach (pull-up suggested by Joerg Reisenweber)
- atusb.brd: increased version to 20101229
- atusb.brd: increase clearance between RF clock front ground area and MCU
(ground area acted as solder trap)
- atusb.brd: route nRST_RF trace out of corner (to avoid accidental
contact)
- atusb.brd: don't route VBUS corner trace underneat chip (for general
tidiness)
- atusb.brd: bumped version to 20101219
- atusb.brd: reduced RF front ground area to avoid interconnections very
close to the chip
- atusb.brd: reduced RF power front ground area to avoid interconnections
very close to the chip
- atusb.brd: moved via next to TXRX pad 18 (GND) to make room for making
CLK trace leave the pad at its end, not at its side
- atusb.brd: bumped design date to 20101217
- usb.sch: use P0.2 as board revision ID pin
- atrf.sch: label feed line
- atusb.brd: set feed line width via design rule, not as user size
- atusb.brd: increase feed line width from 18 mil to 19 mil (it should be
58 mil, but we don't have room for more)
- atusb.brd: bumped version number to 20101202
- atusb.brd: put version number on PCB
- atusb.sch, usb.sch, atrf.sch: bumped version number to 20101202
- atusb.brd: moved traces into USB plug such that they coincide with
thermal relief
- atusb.brd: moved trace into antenna ground such that it coincides
with thermal relief
- atusb.pro: reduced edge and drawing line width from 15 mil to 5 mil
- atusb.brd: added ground zones on bottom layer
- atusb.brd: moved IRQ_RF and VDD traces for better ground area coverage
- atusb.brd: move antenna to its rightful place
- atusb.brd: added two more GND vias after antenna move
- atusb.brd: added proper board edge
- atusb.brd: added board dimensions (16.3 x 33.2 mm)
- atusb.brd: moved via next to C11 closer to C11 and away from RF section
- atusb/atrf.sch (C6, C7): use canonical name 820fF instead of 0.82pF
- atusb/usb.sch (VR1, VR2, VR3): changed value from 5V6 to 5V5 for
compatibility with selected part
- atusb/atusb.sch: commit noise
- atusb/atusb.brd: reloaded for value changes
- atrf/: rename to atusb/
- atrf/wpan-atrf.pro, atrf/wpan-atrf.sch, atrf/wpan-atrf.brd,
atrf/wpan-atrf.cmp: rename to atusb.*
- atrf/Makefile: change ben-wpan to atusb
- atrf/atusb.pro (LastNetListRead): update for name change
- tools/Makefile.common (CFLAGS): change fw/ include location from atrf/
to atusb/
