- atusb.brd: bumped version number to 20101202
- atusb.brd: put version number on PCB
- atusb.sch, usb.sch, atrf.sch: bumped version number to 20101202
- atusb.brd: moved traces into USB plug such that they coincide with
thermal relief
- atusb.brd: moved trace into antenna ground such that it coincides
with thermal relief
- atusb.pro: reduced edge and drawing line width from 15 mil to 5 mil
- atusb.brd: added ground zones on bottom layer
- atusb.brd: moved IRQ_RF and VDD traces for better ground area coverage
- atusb.brd: move antenna to its rightful place
- atusb.brd: added two more GND vias after antenna move
- atusb.brd: added proper board edge
- atusb.brd: added board dimensions (16.3 x 33.2 mm)
- atusb.brd: moved via next to C11 closer to C11 and away from RF section
- atusb/atusb.pro: instead of modules/meander, use experimental ants/meander
- atusb/atusb.pro: typo - it's modules/usb_a_plug_smt, not
modules/usb_a_plug
- atusb/atusb.cmp (ANT1): change antenna from "meander" to "MEANDER-110"
(10% enlarged)
- atusb/atusb.cmp (CON1): change from "miniUSB_B" USB receptacle to
"USB-A-PLUG-SMT" plug
- atusb/atusb.cmp (VR1, VR2, VR3): update value from schematics
We know from CNTR that the capacitance of the 0603 TVS (EPCOS CT0603M4G,
200 pF) is too large and can disturb the USB signal. The 0402 TVS
(Panasonic EZJ-P0V080GA, 100 pF) works much better.
Since we have lots of 0402 components already, just change the remaining
0603 to 0402, too.
- usb.sch (VR1, VR2, VR3): change from 0603 to 0402 and from 5V5 to 5V6
- usb.sch (C1, C2, R1): change from 0603 to 0402
- atrf.sch (R3): set footprint to 0402
- atusb.pro: replaced modules/mini-usb with modules/usb_a_plug
- atusb.pro: removed extension from components/balun-smt6.lib
- atusb.cmp: update footprints for above changes
- atusb.cmp: change 0402 to 0402-M and 0603 to 0603-M, for easier
soldering
This way, we can plug the device into a USB port, like a USB stick.
We use a real plug (instead of shaping the PCB in the form of a plug)
for better mechanical stability.
- atusb.pro: change from components/mini_usb_b to components/usb_a_plug
- usb.sch (CON1): replace MINI_USB_B with USB_A_PLUG
The C2 pads were originally sized for permanently soldering a 100 mil
header. For development, a temporary connection is sufficient. Eventually,
we will just use pogo pins to make this connection.
- usb.sch: changed C2 pads from PAD_120x60 to PAD_60x60
- usb.sch: added comment that pads should be spaced at 100 mil interval
- atusb.sch: removed test points for signals going between USB and RF side
- atusb.sch: TST is no longer a rework item - removed comment saying it is
- atusb.sch, usb.sch, atrf.sch: bumped version number to 100930
- atusb/fw/boot/Makefile: still referred to the project as ATSPI (not ATRF)
in title comment
- atusb/fw/include/atusb/usb-ids.h: still had old atspi path in title comment
- common/io.h: TST is connected to P0_7
- include/at86rf230.h: added test mode registers REG_CONT_TX_0 (0x36) and
REG_CONT_TX_1 (0x3d), with their values
- atspi/atspi.c (set_test_mode): set or reset TST and the LED
- atspi/atspi.c (reset_rf): leave test mode
- atspi/atspi.c (test_mode): enter test mode
- atspi/atspi.c (main): flash the LED when in test mode
- include/atspi/ep0.h (enum atspi_requests), atspi/ep0.c (my_setup): new
command ATSPI_TEST to enter test mode
- include/atspi/ep0.h (EP0ATSPI_MINOR): bumped protocol to version 0.1
- include/at86rf230.h: corrected comment before TRX_CMD field to indicate
that the register is called TRX_STATE
- atusb/atrf.sch (C6, C7): use canonical name 820fF instead of 0.82pF
- atusb/usb.sch (VR1, VR2, VR3): changed value from 5V6 to 5V5 for
compatibility with selected part
- atusb/atusb.sch: commit noise
- atusb/atusb.brd: reloaded for value changes
- atrf/: rename to atusb/
- atrf/wpan-atrf.pro, atrf/wpan-atrf.sch, atrf/wpan-atrf.brd,
atrf/wpan-atrf.cmp: rename to atusb.*
- atrf/Makefile: change ben-wpan to atusb
- atrf/atusb.pro (LastNetListRead): update for name change
- tools/Makefile.common (CFLAGS): change fw/ include location from atrf/
to atusb/
