- atrf-txrx.c (usage, main): added option -C mhz to enable the CLKM output
and to set its frequency
- atrf-txrx.c (init_txrx): if requested, enable CLKM and set to maximum
drive strength
- atrf-txrx.c (init_txrx): unmask all interrupts for 231 compatibilit,
where masked interrupts are now indicated in IRQ_STATUS
- atrf-txrx.c (init_txrx): on the 231, wait for (and clear) the CCA_ED_DONE
interrupt when entering TRX_OFF after reset
- tools/Makefile (upload): make destinastion host name ("ben" or "jlime")
depend on TARGET
- tools/Makefile.common (CC_ben, CFLAGS_ben, LDLIBS_ben, MACROS_ben):
renamed to *_openwrt and added *_jlime equivalents
- tools/atrf-rssi/Makefile: added settings to use SDL_gfx on Jlime
- tools/lib/Makefile (OBJS_ben): renamed to OBJS_ben_openwrt and added
OBJS_ben_jlime
- atrf-txrx.c (test_mode): moved test mode setup to enter_test_mode_230
- atrf-txrx.c (enter_test_mode_231): enter test mode on AT86RF231 (untested)
- atrf-txrx.c (test_mode): reset AT86RF231 register 0x1c when leaving
- atrf-txrx.c (tx_pwr, tx_pwr_230, tx_pwr_231, set_power): table of power
values depends on chip
- atrf-txrx.c (set_power): location of TX_AUTO_CRC_ON and use of
REG_PHY_TX_PWR depends on chip
- tools/lib/atrf.h, tools/lib/atrf.c (atrf_identify): added chip
identification function to library
- tools/atrf-id/atrf-id.c (show_info): print information returned by
atrf_identify
- tools/atrf-id/atrf-id.c (show_info): decode JEDEC manufacturer ID
- tools/atrf-*/atspi-*.c: renamed to atrf-*.c
- tools/atrf-*/Makefile (MAIN): updated name of program
- tools/atrf-*/*.c: updated path in title comment
- tools/atspi-id/: renamed to atrf-id
- tools/atspi-reset/: renamed to atrf-reset
- tools/atspi-rssi/: renamed to atrf-rssi
- tools/atspi-trim/: renamed to atrf-trim
- tools/atspi-txrx/: renamed to atrf-txrx
- tools/Makefile: renamed directories from atspi-* to atrf-*
e lib/misctxrx.o
- atspi-txrx/atspi-txrx.c (usage): rearranged description of -T
- atspi-txrx/atspi-txrx.c (usage, main): option -f freq to specify the
channel by frequency
- atspi-txrx/atspi-txrx.c (set_power): make enabling the CRC optional
(this is necessary for test mode, which doesn't seem to work if the CRC
is selected)
- atspi-txrx/atspi-txrx.c (test_mode): emit a constant wave in test mode
- atspi-txrx/atspi-txrx.c (usage, main): new option -T <delta> to emit a
constant wave -2 MHz, -0.5 MHz, or +0.5 MHz from the nominal carrier
frequency
- include/atspi.h, lib/atspi.c: new function atspi_test_mode to enter test
mode
- lib/driver.h (struct atspi_driver): add backend function test_mode
- lib/atusb.c (atusb_test_mode), lib/atusb.c (atusb_driver): enter test
mode
- lib/atusd.c (atusd_driver): test mode is not supported
- atspi-rssid/gui.c (sweep, label_channels): moved geometry values to
#defines
- atspi-rssid/gui.c (CBIG, CSMALL, label_channels): moved color values to
#defines
- tools/Makefile.common: CFLAGS and OBJS can now be target-specific
- tools/atspi-rssi/Makefile: add SDL, SDL_gfx, and the GUI object files
when building on the host
- tools/atspi-rssi/Makefile: set -DHAVE_GFX when building on the host
- tools/atspi-rssi/atspi-rssi.c (usage, main): new option -g to use GUI
mode
- tools/atspi-rssi/atspi-rssi.c (main): rename variable for the number of
sweeps in non-GUI mode from "sweeps" to "arg", since it may have other
uses in the future
- tools/atspi-rssi/digit.h, tools/atspi-rssi/digit.c: draw 7 segment style
digits
- tools/atspi-rssi/zgrid.h, tools/atspi-rssi/zgrid.c: display a surface in
faux 3D with SDL/SDL_gfx
- tools/tools/atspi-rssi/gui.h, tools/atspi-rssi/gui.c: display RSSI scans
as a scrolling 3D profile
- atrf/: rename to atusb/
- atrf/wpan-atrf.pro, atrf/wpan-atrf.sch, atrf/wpan-atrf.brd,
atrf/wpan-atrf.cmp: rename to atusb.*
- atrf/Makefile: change ben-wpan to atusb
- atrf/atusb.pro (LastNetListRead): update for name change
- tools/Makefile.common (CFLAGS): change fw/ include location from atrf/
to atusb/
if it differs by more than 0.01 dBm from the level specified
- tools/atspi-txrx/Makefile (LDLIBS): added -lm, for fabs()
- tools/atspi-txrx/atspi-txrx.c (transmit, usage, main): add optional
command-line argument with the number of times to send the message
- tools/atspi-txrx/atspi-txrx.c (receive, transmit, die, main): return and
clean up on ^C
- tools/tools/lib/misctxrx.c (wait_for_interrupt) return and raise SIGINT
for the caller's signal handler on ^C
- atrf/fw/include/atspi/ep0.h enum atspi_requests), atrf/fw/atspi/ep0.c
(my_setup): new command ATSPI_POLL_INT to poll IRQ_RF
- atrf/fw/atspi/ep0.c (my_setup): ATSPI_BUILD sent one byte too many
- tools/lib/atusb.c (atusd_interrupt, atusb_driver): implemented interrupt
polling
- tools/lib/atusd.c: added section title for the RF interrupt function
- tools/atspi-rssi/atspi-rssi.c: removed unnecessary inclusion of
atspi/ep0.h
- tools/atspi-rssi/atspi-rssi.c (sweep): instead of fixed delay, wait for
the PLL lock interrupt
- tools/atspi-rssi/atspi-rssi.c (die, main): catch SIGINT to exit cleanly
- tools/atspi-rssi/atspi-rssi.c (main): shut down properly when done
- tools/atspi-rssi/atspi-rssi.c (usage): print "usage:" before the program's
name
- tools/atspi-txrx/atspi-txrx.c: cleaned up includes - we need stdint.h but
we don't need atspi/ep0.h
- tools/atspi-txrx/atspi-txrx.c (wait_for_interrupt),
tools/include/misctxrx.h (wait_for_interrupt), tools/lib/Makefile (OBJS),
tools/lib/misctxrx.c (wait_for_interrupt): moved wait_for_interrupt from
atspi-txrx to the atspi library, so that we can share it
- tools/atspi-txrx/atspi-txrx.c (receive, wait_for_interrupt): moved wait
for interrupt logic to separate function and made it more versatile
- tools/atspi-txrx/atspi-txrx.c (init_txrx, receive): clear interrupts in
init_txrx now, so that also transmit has a clear interrupt register
- tools/atspi-txrx/atspi-txrx.c (set_channel): since we're in TRX_OFF,
don't wait for PLL lock
- tools/atspi-txrx/atspi-txrx.c (receive): wait for PLL lock interrupt
after activating receiver
- tools/atspi-txrx/atspi-txrx.c (transmit): wait for PLL lock interrupt
after activating the PLL
- tools/atspi-txrx/atspi-txrx.c (transmit): wait for TRX_END interrupt
after sending a frame
- tools/atspi-txrx/atspi-txrx.c (receive): report the Energy Density (ED)
after receiving a frame
- tools/atspi-txrx/atspi-txrx.c (main): shut down the board with
atspi_close, so that we can hot-swap safely
- tools/lib/atusd.c (spi_send_partial, spi_send): removed the old spi_send
and renamed spi_send_partial to spi_send
- tools/lib/atusd.c (atusd_cycle, spi_send, spi_recv, atusd_open): updated
for removal of SLP_TR and split of MxSx into MOSI and MISO
- tools/lib/atusd.c (atusd_reset_rf, atusd_open): added delays to precharge
the capacitors
- tools/lib/atusd.c (atusd_reset, spi_data_in, spi_data_out, spi_finish):
removed functions for obsolete hardware features
- tools/lib/atusd.c (atusd_reg_read): removed calls to removed functions
- tools/lib/atusd.c (atusd_buf_write, atusd_buf_read, atusd_driver): new
buffer read/write functions
- tools/atspi-txrx/atspi-txrx.c (init_txrx): set the internal osciallator
trim only in the USB version. Switch to the external oscillator in the
uSD version.
- tools/atspi-rssi/atspi-rssi.c (sweep), tools/atspi-txrx/atspi-txrx.c
(set_channel): wait for the PLL to settle after setting the channel
- tools/include/atspi.h, tools/lib/atspi.c (atspi_interrupt),
tools/lib/driver.h (struct atspi_driver), tools/lib/atusd.c
(atusd_interrupt): new function to poll the interrupt line
- tools/atspi-txrx/atspi-txrx.c (receive): only read REG_IRQ_STATUS if
there is a pending interrupt
- tools/atspi-id/atspi-id.c (usage): print "usage:" as well
- tools/Makefile (upload): upload the atspi tools to the Ben
- tools/lib/atusd.c (atusd_cycle): we never turned power back on ?
- tools/atspi-id/atspi-id.c (main): call atspi_close on exit
- tools/lib/atusd.c (atusd_cycle, wait_for_power): moved power on delay to
separate function
- tools/lib/atusd.c (atusd_open): wait for power to stabilize
- tools/lib/atusd.c (atusd_open): need to reset the board to bring it
up properly
- tools/Makefile.common: set CC to the target-specific compiler
- tools/atspi-id/atspi-id.c: exclude everything USB if HAVE_USB is not set
- tools/atspi-id/atspi-id.c (atspi_usb_handle): rearrange to use a "struct
atspi_dsc *" argument, so that we don't expose an USB dependency
- tools/lib/Makefile: $(F32XBASE)/lib/usb.o is target-specific. Moved it
from OBJS to OBJS_host.
- tools/lib/Makefile (clean): remove objects of all targets
- atusd/tools/lib/atusd.c: moved to tools/lib/
- atusd/tools/lib/atusd.h: removed, we can now use tools/include/atspi.h
- tools/lib/atusd.c: added copyright header
- tools/lib/atusd.c: updated for driver API
- tools/lib/Makefile: added atusd.o
- tools/Makefile.common: moved common elements from all other makefiles in
tools/*/ here
- tools/Makefile.common: added target-specific compiler and flags
- tools/atspi-id/Makefile, tools/atspi-reset/Makefile,
tools/atspi-rssi/Makefile, tools/atspi-trim/Makefile,
tools/atspi-txrx/Makefile, tools/lib/Makefile: used Makefile.common
- tools/lib/Makefile: differentiate USB and uSD build
- tools/atspi-id/atspi-id.c, tools/atspi-reset/atspi-reset.c,
tools/atspi-rssi/atspi-rssi.c, tools/atspi-trim/atspi-trim.c,
tools/atspi-txr/atspi-txr.c: updated for driver-agnostic API
- tools/atspi-id/atspi-id.c, tools/atspi-reset/atspi-reset.c,
tools/atspi-rssi/atspi-rssi.c, tools/atspi-trim/atspi-trim.c,
tools/atspi-txr/atspi-txr.c: corrected AF86RF230 typo in title
- tools/include/atspi.h, tools/lib/atspi.c, tools/lib/driver.c,
tools/lib/atusb.c: brought back support for atspi_error and
atspi_clear_error
- tools/atspi-id/atspi-id.c (atspi_get_protocol): renamed to get_protocol,
to make it clear that it's not from libatspi
- tools/atspi-id/atspi-id.c (atspi_get_build): renamed to get_build, to
make it clear that it's not from libatspi
- tools/include/atspi.h, tools/lib/atspi.c (atspi_usb_handle): new function
to obtain a driver's USB device handle (or NULL if the driver doesn't use
USB)
- tools/include/atspi.h: API is now driver-independent
- tools/lib/driver.h: API between driver and frontend
- tools/lib/atspi.c: renamed to atusb.c and updated for driver API
- tools/lib/atspi.c: frontend functions for the driver API
- tools/lib/Makefile: added atusb.o
- atrf/tools/: moved to tools/
- tools/Makefile: updated path to Makefile.recurse
- tools/atspi-id/Makefile, tools/atspi-reset/Makefile,
tools/atspi-rssi/Makefile, tools/atspi-trim/Makefile,
tools/atspi-txrx/Makefile, tools/lib/Makefile: updated paths to f32xbase
and to atrf/fw/include
- fw/: moved to atrf/fw/
- tools/: moved to atrf/tools/
- atrf/fw/atspi/Makefile, atrf/fw/boot/Makefile: updated relative path to
f32xbase
- atrf/tools/Makefile: updated relative path to Makefile.recurse
- atrf/tools/atspi-id/Makefile, atrf/tools/atspi-reset/Makefile,
atrf/tools/atspi-rssi/Makefile, atrf/tools/lib/Makefile: updated relative
path to f32xbase
- atrf/fw/include/at86rf230.h: corrected path in title
- atrf/tools/include/atspi.h: added title and copyright header
- tools/include/atspi.h, tools/lib/atspi.c (atspi_reset): new function to
send the ATSPI_RESET command (MCU reset)
- tools/include/atspi.h, tools/lib/atspi.c (atspi_reset_rf): new function
to send the ATSPI_RESET_RF command (transceiver reset)
- tools/atspi-reset/Makefile, tools/atspi-reset/atspi-reset.c: reset utility
- tools/atspi-txrx/Makefile, tools/atspi-txrx/atspi-txrx.c: new utility
that, for now, just turns on the DVDD regulator
- tools/atspi-id/Makefile: corrected path in title
- fw/include/at86rf230.h: changed TRX_STATE_* to TRX_CMD_*
