- atrf-txrx.c (set_rate, main): allow setting a non-standard high data
rate on the AT86RF231
- atrf-txrx.c (usage, main): added option -r to select the data rate
- atrf-txrx.c (struct ping, enum rx_res, ping_tx, ping_rx, ping): send
back a packet containing a locally generated sequence number and the
last sequence number received whenever a packet arrives
- atrf-txrx.c (usage, main): added option -P to select ping mode
- atrf-txrx.c (usage, main): changed option -B to -P
- atrf-txrx.c (usage): "BER test mode" is now "PER test mode"
- atrf-txrx.c (main): mode_ber is now mode_per
- pcap.h (PCAP_FILE_MAGIC): define the pcap file magic number
- atrf-txrx.c (write_pcap_hdr): use PCAP_FILE_MAGIC instead of open-coding
the magic number
- atrf-txrx.c (main): indicate mode of operation in variable "mode" instead
of dual-using "cont_tx"
- atrf-txrx.c (usage, main): added option -B to enter BER test pattern
transit mode
- atrf-txrx.c (transmit_pattern): transmit raw frames with a cyclic frame
number
- pcap.h: basic pcap file structure definitions
- atrf-txrx.c (usage, main): added option "-o file" to write received
frames to a pcap file instead of displaying them
- atrf-txrx.c (receive): moved code to receive and display a single message
into new function receive_message
- atrf-txrx.c (write_pcap_hdr, write_pcap_rec, receive_pcap): receive
messages into a pcap file
- atrf-txrx.c (usage): split options and arguments for different modi into
separate sections
- atrf-txrx.c (usage): moved details for common options to a separate
section
- atrf-txrx.c (usage): added -C mhz to synopsis
- lib/atusd.c: renamed CLK to SLP_TR
- lib/atusd.c (atusd_cycle, atusd_cycle, atusd_open, atusd_close):
#ifdef'ed all uses of CLK and changed them to SLP_TR (along with the
change in function)
- atrf-txrx/atrf-txrx.c (init_txrx): always use the crystal oscillator
According to the data sheet, it has to be enabled. The Software Model
doesn't mention it. Experiments show that it's indeed useless and just
adds noise.
- atrf-txrx.c (usage, main): added option -C mhz to enable the CLKM output
and to set its frequency
- atrf-txrx.c (init_txrx): if requested, enable CLKM and set to maximum
drive strength
- atrf-txrx.c (init_txrx): unmask all interrupts for 231 compatibilit,
where masked interrupts are now indicated in IRQ_STATUS
- atrf-txrx.c (init_txrx): on the 231, wait for (and clear) the CCA_ED_DONE
interrupt when entering TRX_OFF after reset
- atrf-txrx.c (test_mode): moved test mode setup to enter_test_mode_230
- atrf-txrx.c (enter_test_mode_231): enter test mode on AT86RF231 (untested)
- atrf-txrx.c (test_mode): reset AT86RF231 register 0x1c when leaving
- atrf-txrx.c (tx_pwr, tx_pwr_230, tx_pwr_231, set_power): table of power
values depends on chip
- atrf-txrx.c (set_power): location of TX_AUTO_CRC_ON and use of
REG_PHY_TX_PWR depends on chip
- tools/atrf-*/atspi-*.c: renamed to atrf-*.c
- tools/atrf-*/Makefile (MAIN): updated name of program
- tools/atrf-*/*.c: updated path in title comment
