Production and testing: Software setup

Before performing production tests, various pieces of software need to be installed on Ben and PC, and configuration settings may have to be adjusted. The following sections describe the installation and configuration process.

For a DUT and reference device role, the ben-wpan utilities and the test scripts have to be installed on the PC. For flashing the atusb application firmware, also dfu-util and the firmware binary are required.

The instructions below assume that a complete development environment is already present on the PC, including SDL and SDL_gfx. If any prerequisites are not met, compilation will fail, and you'll have to install the corresponding package and try again. To build the ben-wpan tools and install them under /usr/local/ on the local machine, run the following commands:

git clone git://projects.qi-hardware.com/ben-wpan.git
git clone git://projects.qi-hardware.com/f32xbase.git
cd ben-wpan/tools
make
make install

A different directory prefix can be chosen by overriding the INSTALL_PREFIX variable, e.g.,

make INSTALL_PREFIX=/usr install

Note that the test scripts expect ${INSTALL_PREFIX}/bin to be in PATH. The test scripts are in the directory prod/ of the ben-wpan project. They currently are designed to be run from this directory. Therefore, all that's necessary is to check out the repository, as shown above. dfu-util is used to transfer the application firmware to atusb boards. To build dfu-util from source, run these commands:

git clone git://git.openezx.org/dfu-util.git
cd dfu-util
./autogen.sh
./configure
make
make install

Note that some Linux distributions already provide a pre-compiled version of dfu-util, which could be used instead of building it from source. The binary of the application running on atusb is transferred from the PC. To download a pre-compiled version, use this command:

wget -O atusb.bin \
     http://downloads.qi-hardware.com/people/werner/wpan/bindist/atusb-de72af351f661b538add81cbc9965278a2f8c40c.bin

Instructions for building the binary from sources are here. To simplify accessing the Ben via TCP/IP, its IP address should be registered in the hosts file on the PC. If the Ben is running OpenWrt, use the following command:

echo 192.168.254.101 ben >>/etc/hosts

If the Ben is running Jlime, the address would be as follows:

echo 192.168.1.202 ben >>/etc/hosts

If using the same PC with Bens running OpenWrt and Jlime, one may choose different host names depending on the distribution, and adapt the commands used in the production and testing process accordingly. For example,

echo 192.168.254.101 ben >>/etc/hosts
echo 192.168.1.202 jlime >>/etc/hosts

@@@

For a DUT and reference device role, the ben-wpan utilities have to be installed on a Ben. For flashing the atusb boot loader, also avrdude and the boot loader binary are needed.

The instructions below apply for OpenWrt and Jlime. For building things from source, a cross-compilation toolchain has to be installed on the PC. To enable password-less remote access from the PC, set up network access to the Ben and run the following command:

ssh ben 'cat >>/etc/dropbear/authorized_keys' <~/.ssh/id_rsa.pub

To build and install the ben-wpan tools on the Ben, first set up networking between the PC and the Ben. If you have not yet checked out the project's repository, run these commands:

git clone git://projects.qi-hardware.com/ben-wpan.git
git clone git://projects.qi-hardware.com/f32xbase.git
cd ben-wpan/tools

If you have already checked out the repository, cd to ben-wpan/tools/ and run

make clean

Next, if on OpenWrt, compile the tools with

make TARGET=ben_openwrt

If on Jlime, use

make TARGET=ben_jlime

Finally, upload the tools to the Ben and install them under /usr/bin/ with

make HOST=ben install

Where ben is the host name or IP address assigned to the Ben. The atusb boot loader is flashed using avrdude. A pre-compiled static binary (suitable for OpenWrt and Jlime) can be installed by running the following two command on the Ben:

wget http://downloads.qi-hardware.com/people/werner/wpan/bindist/avrdude-5.10-de72af351f661b538add81cbc9965278a2f8c40c.tar.gz
tar -xz -C / -f avrdude-5.10-de72af351f661b538add81cbc9965278a2f8c40c.tar.gz

Instructions for building avrdude from sources are here. The binary of the boot loader running on atusb is transferred from the Ben. To download a pre-compiled version, use this command:

wget -O boot.hex \
   http://downloads.qi-hardware.com/people/werner/wpan/bindist/boot-de72af351f661b538add81cbc9965278a2f8c40c.hex

Instructions for building the binary from sources are here.

The configuration setting described in this section are lost on each reset or reboot and either need to be entered again. Alternatively, a setup script running at boot time can be written. Once the Ben has booted and started USB networking, the interface on the PC side is configured as follows:

ifconfig usb0 192.168.254.100 up

These are the settings for OpenWrt, assuming the network device is called "usb0". If using Jlime, the command would be as follows:

ifconfig usb0 192.168.1.200 up

Before running any of the ben-wpan utilities, other users of the 8:10 card slot have to be disabled. In a Ben running the regular OpenWrt or Jlime distribution, the only such user that is automatically started is the MMC kernel driver. The following command disables it:

echo jz4740-mmc.0 >/sys/bus/platform/drivers/jz4740-mmc/unbind

If a WPAN-enabled kernel has been installed, the AT86RF230 driver takes the place of the MMC driver. To disable it, run

echo spi2.0 >/sys/bus/spi/drivers/at86rf230/unbind

On the Ben, launch the proxy daemon. We pass the option -b to background it:

atrf-proxy -b

Some of the functional tests measure characteristics that are strongly influenced by the test setup. It is therefore not possible to provide universally applicable reference values, but they have to be measured in the actual test environment. Insert a known to be good atben board and run the following command directly on the Ben to record the reference value for the clock count with an accuracy of about +/−20 ppm:

atrf-xtal 1000 >ben.xtal

This takes about 5 seconds.

Note that the result depends on the tolerance of the crystal in the Ben and is also affected by temperature. Good accuracy can therefore only be obtained if this measurement is performed individually on each Ben, and if a stable temperature is maintained. @@@