ben-wpan

mirror of git://projects.qi-hardware.com/ben-wpan.git synced 2024-11-23 00:42:28 +02:00

History

Werner Almesberger 2acdaca218 atusb/fw/: moved timer initialization to board_app.c as well - board.c (board_init), board_app.h (timer_init), board_app.c (timer_init): moved timer initialization from board_init to new function timer_init - atusb.c (main): call timer_init		2011-06-11 01:52:16 -03:00
..
an	moved atusb/fw3/ to atusb/fw/	2011-02-22 00:24:07 -03:00
include	atusb/fw/: new request ATUSB_SLP_TR to pulse SLP_TR	2011-06-05 22:34:49 -03:00
usb	atusb/fw/usb/: DFU_ITF_DESCR also needs a protocol argument	2011-06-10 23:15:51 -03:00
atusb.c	atusb/fw/: moved timer initialization to board_app.c as well	2011-06-11 01:52:16 -03:00
board_app.c	atusb/fw/: moved timer initialization to board_app.c as well	2011-06-11 01:52:16 -03:00
board.c	atusb/fw/: moved timer initialization to board_app.c as well	2011-06-11 01:52:16 -03:00
board.h	atusb/fw/: moved timer initialization to board_app.c as well	2011-06-11 01:52:16 -03:00
boot.c	atusb/fw/boot.c (main): reset_rf implies spi_init - no need to call it here	2011-06-09 12:52:51 -03:00
descr.c	atusb/fw/: added transition from runtime to DFU mode according to DFU spec	2011-06-10 23:26:36 -03:00
ep0.c	atusb/fw/: added transition from runtime to DFU mode according to DFU spec	2011-06-10 23:26:36 -03:00
flash.c	atusb/fw: introduced function flash_end_write to properly finish flashing	2011-03-11 17:56:41 -03:00
Makefile	atusb/fw/: added transition from runtime to DFU mode according to DFU spec	2011-06-10 23:26:36 -03:00
README	atusb/fw/README: boot loader flashing time was a bit too optimistic (15 -> 30 s)	2011-05-09 23:44:51 -03:00
sernum.c	atusb/fw: use the unique serial number of the ATmega8/16/32U2 for iSerialNumber	2011-05-10 17:23:08 -03:00
sernum.h	atusb/fw: use the unique serial number of the ATmega8/16/32U2 for iSerialNumber	2011-05-10 17:23:08 -03:00
spi.c	atusb/fw/: added "lazy enabling" of UART-SPI after ATUSB_GPIO	2011-06-09 14:02:26 -03:00
spi.h	atusb/fw/: added "lazy enabling" of UART-SPI after ATUSB_GPIO	2011-06-09 14:02:26 -03:00
version.h	moved atusb/fw3/ to atusb/fw/	2011-02-22 00:24:07 -03:00

README

Requires a very recent toolchain, because ATmega32U2 is relatively new.

- Building:

  make

- Uploading the firmware to a Ben (for flashing with the atusb-pgm cable):

  make HOST=<hostname> upload

  Example:

  make HOST=ben upload

  HOST defaults to "jlime".

- Flashing the boot loader:

  Prerequisite: avrdude on the Ben.

  Disconnect the atusb board from USB. Insert the atusb-pgm connector into
  the Ben. Place the atusb-pgm adapter on the exposed contact pads of the
  atusb board and push it down. Then run

  make prog

  This takes about 30 seconds. If the programming fails with an error
  message like "Yikes!  Invalid device signature.", verify that the
  atusb-pgm board is properly connected and placed, then try again.

- Uploading the application:

  Prerequisite: dfu-util installed on the PC.

  Insert atusb into the PC, then run

  make dfu

  Note: since the boot loader resets the USB bus after timing out,
  this operation can fail with a message like "No DFU capable USB device
  found". Just retry, and it will eventually get through.

--------------------------

Making the toolchain:

# patches according to
# http://www.avrfreaks.net/index.php?name=PNphpBB2&file=viewtopic&p=789527

# some gcc prerequisites

apt-get remove avr-libc gcc-avr binutils-avr
apt-get install libmpfr-dev libmpc-dev

# binutils

wget http://ftp.gnu.org/gnu/binutils/binutils-2.21.tar.bz2
tar xfj binutils-2.21.tar.bz2 
cd binutils-2.21
./configure --target=avr --disable-nls
make
make install

# gcc

wget http://ftpmirror.gnu.org/gcc/gcc-4.5.2/gcc-4.5.2.tar.bz2
wget -O gcc_452_avr.patch http://gcc.gnu.org/bugzilla/attachment.cgi?id=23050
tar xfj gcc-4.5.2.tar.bz2
cd gcc-4.5.2
patch -p1 -s <../gcc_452_avr.patch
mkdir obj-avr
cd obj-avr
../configure --target=avr --enable-languages=c \
    --disable-nls --disable-libssp --with-dwarf2
make
make install

wget http://download.savannah.gnu.org/releases/avr-libc/avr-libc-1.7.1.tar.bz2
tar xfj avr-libc-1.7.1.tar.bz2 
cd avr-libc-1.7.1
./bootstrap	# the automake at the end takes a while
./configure --build=`./config.guess` --host=avr
make
make install