mirror of
git://projects.qi-hardware.com/ben-wpan.git
synced 2024-12-29 04:24:36 +02:00
107 lines
4.1 KiB
Plaintext
107 lines
4.1 KiB
Plaintext
Arbitrary-precision frequency counter
|
|
=====================================
|
|
|
|
Theory of operation
|
|
-------------------
|
|
|
|
The arbitrary-precision frequency counter counts clock cycles of a
|
|
frequency source that is assumed to be free from drift. It compares the
|
|
count with the host's system clock. If the system clock is synchronized
|
|
with an accurate NTP reference, measurements with arbitrarily high
|
|
accuracy can be obtained.
|
|
|
|
In practice, this is limited by the the frequency source's drift and
|
|
the time one is willing to wait. If NTP maintains the system time
|
|
with an accuracy of +/- 100 ms, obtaining measurements with an
|
|
accuracy of +/- 1 ppm would take about 28 hours.
|
|
|
|
Additional error sources, such as the round-trip time when requesting
|
|
a sample from the microcontroller, are also considered in the accuracy
|
|
calculation.
|
|
|
|
The counter consists of a board based on a C8051F320 microcontroller
|
|
and the control software on the host. The microcontroller counts
|
|
events in a free-running 16 bit counter that is regularly read and
|
|
extended to 32 bits. The 32 bit counter is periodically queried by
|
|
the host.
|
|
|
|
The microcontroller's counter can count at a frequency of up to 3 MHz.
|
|
(SYSCLK/4)
|
|
|
|
In order to protect against transmission errors not detected by USB's
|
|
CRC, which are occur relatively often, each packet is protected by a
|
|
CRC-32 and an inverted copy of the payload. Corrupted packets are
|
|
rejected by the host.
|
|
|
|
The 32 bit counter wraps around at most once very 21.8 ms. The 32 bit
|
|
counter wraps around at most every 1431 s. The host extends the 32 bit
|
|
counter to 64 bits, and calculates frequency and accuracy from the
|
|
count and the run time of the measurement application.
|
|
|
|
|
|
Performing a measurement
|
|
------------------------
|
|
|
|
To perform a measurement, connect the CNTR board's probe input to the
|
|
clock source and then run the "cntr" application on the host. An
|
|
accuracy goal (in ppm) can be specified on the command line (see
|
|
below).
|
|
|
|
The host polls the microcontroller every 100 ms and displays the run
|
|
time (in seconds), the measured frequency, and the accuracy achieved
|
|
so far.
|
|
|
|
Measurements can be stopped by pressing ^C or by specifying an
|
|
accuracy goal. At the end, the total number of events counted and
|
|
communication statistics are displayed.
|
|
|
|
|
|
Updating the firmware
|
|
---------------------
|
|
|
|
The protocol revision and the build date of the firmware of the CNTR
|
|
board can be queried with "cntr -i".
|
|
|
|
To update the firmware, run
|
|
cntr -r; sleep 1 && dfu-util -d 0x20b7:0xcb72 -D cntr.bin
|
|
|
|
|
|
Known issues (version 2 hardware)
|
|
---------------------------------
|
|
|
|
- the input circuit only works up to about 1 MHz. The problem is that
|
|
we discharge too slowly though the base of Q1, which in turn keeps
|
|
the transistor turned on too long.
|
|
|
|
An alternative design that sets R2 to zero, adds a 47 Ohm termination
|
|
resistor in parallel to VR4, and places a 1 kOhm resistor between
|
|
VR4 and Q1 works up to about 2 MHz, but accepts a lot of HF noise
|
|
and is very sensitive to the signal amplitude.
|
|
|
|
Some test results with a ~1.8 m RG-174 cable, square wave bursts
|
|
with a 50% duty cycle and ~ 5 ns raise/fall time:
|
|
|
|
Design Frequency Source amplitude Input amplitude
|
|
(nominal) (nominal) (measured)
|
|
------------ ---------- ---------------- ---------------
|
|
Original 1 MHz 700 mV ~700 mV
|
|
Alternative 2 MHz 1.6 V ~800 mV
|
|
1 MHz 1.5 V ~750 mV
|
|
|
|
The test consisted of setting the frequency and adjusting the nominal
|
|
source voltage in increments of 100 mV for the lowest voltage at
|
|
which which ten consecutive bursts of 50000 cycles each were all
|
|
received correctly.
|
|
|
|
The source has an output impedance of 50 Ohm, so voltage at the probe
|
|
input (indicated in the table) is roughly half the nominal source
|
|
voltage in the alternative design.
|
|
|
|
- the MMCX connector is hard to solder because of its large thermal
|
|
capacitance and surface
|
|
- the lateral pads of the MMCX connector could be wider
|
|
- manufacturing tolerances can push the USB connector a bit inside
|
|
the board, making its signal pins overshoot the pads
|
|
- the ground fill under the LED causes a secondary cathode contact
|
|
(which is harmless on this case)
|