mirror of
git://projects.qi-hardware.com/ben-wpan.git
synced 2024-11-06 04:15:55 +02:00
80 lines
2.3 KiB
HTML
80 lines
2.3 KiB
HTML
<TITLE>Production and testing: Flashing</TITLE>
|
|
<BODY>
|
|
<HTML>
|
|
<H1>Production and testing: Flashing</H1>
|
|
|
|
The microcontroller of <B>atusb</B> contains firmware that must be
|
|
loaded before the testing process can commence. The firmware consists
|
|
of the following two parts:
|
|
<OL>
|
|
<LI>The boot loader (via serial programming, using <B>avrdude</B>)
|
|
<LI>The application (via DFU, using <B>dfu-util</B>)
|
|
</OL>
|
|
<P>
|
|
Note that <B>atben</B> has no microcontroller and therefore does not need
|
|
any flashing.
|
|
|
|
|
|
<!-- ====================================================================== -->
|
|
|
|
|
|
<H2>Flashing the boot loader</H2>
|
|
|
|
The following image shows the setup for flashing the boot loader:
|
|
<P>
|
|
<IMG src="setup-C.png">
|
|
<P>
|
|
To flash the boot loader,
|
|
<UL>
|
|
<LI>insert the <B>atusb-pgm</B> board into the Ben
|
|
<LI>place the <B>atusb</B> board (DUT) on the table near the Ben,
|
|
without connecting it to USB
|
|
<LI>place <B>atusb-pgm</B> on <B>atusb</B> as shown in the image below
|
|
and gently push it on the contacts
|
|
<P>
|
|
<A href="atusb-programming.jpg"><IMG
|
|
src="atusb-programming.jpg" width="250"></A>
|
|
<P>
|
|
<LI>finally, run
|
|
<PRE>
|
|
make flash
|
|
</PRE>
|
|
</UL>
|
|
<P>
|
|
The flashing takes about 20-30 seconds. If it should fail, make sure you
|
|
properly placed <B>atusb-pgm</B> and try again. If it keeps on failing,
|
|
remove <B>atusb-pgm</B> from the Ben and insert it again.
|
|
If flashing fails despite numerous attempts, proceed to the
|
|
<A href="analysis.html">fault analysis</A>.
|
|
|
|
|
|
<!-- ====================================================================== -->
|
|
|
|
|
|
<H2>Flashing the application</H2>
|
|
|
|
The flashing script proceeds automatically to the flashing of the
|
|
application. All you need to do is insert the <B>atusb</B> board
|
|
into the PC:
|
|
<P>
|
|
<IMG src="setup-D.png">
|
|
<P>
|
|
The flashing script will wait up to 30 seconds for enumeration.
|
|
Once the <B>atusb</B> board has been detected, the script transfers
|
|
the application with DFU. After this, you can proceed with the
|
|
<A href="test.html">functional test</A>.
|
|
<P>
|
|
If the board fails to enumerate, proceed with the
|
|
<A href="analysis.html">fault analysis</A>.
|
|
|
|
<P>
|
|
<HR>
|
|
Up: <A href="index.html">Production and testing</A>
|
|
Prev: <A href="setup.html">Software setup</A>
|
|
Next: <A href="test.html">Functional test</A>
|
|
<HR>
|
|
Last update: 2011-05-26 <I>Werner Almesberger</I>
|
|
<HR>
|
|
</BODY>
|
|
</HTML>
|