1
0
mirror of git://projects.qi-hardware.com/cae-tools.git synced 2024-12-23 09:17:42 +02:00
cae-tools/cameo/templates/mkmk-simple

136 lines
2.9 KiB
Bash
Executable File

#!/bin/sh
PATH=$PATH:/home/qi/cae-tools/cameo
PATH=$PATH:/home/qi/cae-tools/gp2rml
#
# Parameters:
#
# NAME KiCad project name, required
# X0, Y0 lower left corner of raw board, default: 0mm 0mm
# X, Y position in array, default: 0 0
# XN, YN number of boards in X/Y direction, default: 1 1
# ROT board rotation, default: 0 degrees
# DRILL drill diameter range, default: 13mil,14mil
# MILL_IN diameter of mill for work inside the board, default: 35mil
# MILL_OUT diameter of mill for board edge, default: 35mil
# BOARD_Z board tickness, default: 0.8 mm
# ANY set to "any" to use all remaining paths for milling,
# irrespective of tool size. Default: unset / empty string.
# CLEARANCE tool clearance above PCB surface, default: 2mm
#
while [ "$1" ]; do
eval "$1"
shift
done
if ! [ "$NAME" ]; then
echo "NAME is required" 1>&2
exit 1
fi
: ${X0:=0} ${Y0:=0}
: ${X:=0} ${Y:=0}
: ${XN:=1} ${YN:=1}
: ${DRILL:="13mil 14mil"}
: ${MILL_IN:=35mil}
: ${MILL_OUT:=35mil}
: ${BOARD_Z:=0.8mm}
: ${CLEARANCE:=2mm}
rot=
if [ "$ROT" ]; then
rot="rotate $ROT"
fi
edges=$NAME.gp
[ -r "$edges" ] || edges=
for n in PCB_Edges.gbr Edge_Cuts.gbr Edge_Cuts.pho; do
if [ -r "../$NAME-$n" ]; then
edges=../$NAME-$n
break
fi
done
if [ ! "$edges" ]; then
echo "no edges file found" 1>&2
exit 1
fi
write=write
yi=0
while [ $yi -lt $YN ]; do
xi=0
while [ $xi -lt $XN ]; do
cameo <<EOF || exit
mm
`if [ "$edges" != "${edges%.gp}" ]; then echo gnuplot 35mil $edges;
else echo gerber 35mil $edges; fi`
$rot
align 1 $X0 $Y0 # align relative to board corner
translate 4mm 4mm # move to PCB zone assigned to project
array +3mm +3mm `expr $X + $xi` `expr $Y + $yi`
z 0 -58.9mm # board surface (tool fully retracted)
z 1.5mm # slack for extending the tool
z -$BOARD_Z # board thickness
z -0.5mm # tool extra depth
clear
`[ -r ../$NAME.drl ] && echo excellon ../$NAME.drl`
`[ -r ../$NAME-NPTH.drl ] && echo excellon ../$NAME-NPTH.drl`
drill $DRILL
optimize
$write drill.gp
remainder
mill $ANY $MILL_IN 0.01mm
$write mill.gp
remainder
empty
`if [ "$edges" != "${edges%.gp}" ]; then echo gnuplot $MILL_OUT $edges;
else echo gerber $MILL_OUT $edges; fi`
offset
append mill.gp
EOF
write=append
xi=`expr $xi + 1`
done
yi=`expr $yi + 1`
done
gp2rml $CLEARANCE 0.5 0.5 mill.gp >mill.rml || exit
gp2rml $CLEARANCE 0.1 0.5 drill.gp >drill.rml || exit
cat <<EOF >Makefile.mkmk
SPOOL=/home/moko/svn.openmoko.org/developers/werner/cncmap/spool/spool
CNGT=/home/qi/cae-tools/cngt/cngt
.PHONY: mill drill cng plot dplot
mill:
PORT=/dev/ttyUSB0 \$(SPOOL) mill.rml
drill:
PORT=/dev/ttyUSB0 \$(SPOOL) drill.rml
cng:
\$(CNGT) -57.4 20 mill.gp
plot:
echo 'set size ratio -1; \
plot "drill.gp" with points, "mill.gp" with lines' | \\
gnuplot -persist
dplot:
echo 'set size ratio -1; \
plot "< sed /^\$\$/d drill.gp" with linespoints' | \\
gnuplot -persist
clean::
rm -f mill.gp mill.rml drill.gp drill.rml
EOF