qi-hardware/openwrt-xburst
1
0
Fork 0
mirror of git://projects.qi-hardware.com/openwrt-xburst.git synced 2024-11-09 22:44:04 +02:00
Code
c428c49464
openwrt-xburst/package/broadcom-57xx/Makefile

53 lines
1.3 KiB
Makefile
Raw Normal View History

(6/6) bcm57xx: package This is the bcm57xx package. I have tested default vlan functions, but I dont have the equipment to test more advanced setups. The default vlan setup seems to be working fine. I also added the activate_gpio parameter which will make the driver activate the switch via gpio before probing for it. I'm not sure which method is best for autoload. For the wrt350n, I need the activate_gpio parameter. But its probably not a good idea to add that to the autoload file. On a system without a bcm57xx switch, isn't it a bad idea to mess with the gpios looking for the switch? Ideally, wouldn't it be best to load the bcm57xx module from broadcom-diag, after it has determined which router its on? I tried using 'request_module' from there, but had no success. For now, I am relying on preinit to load the bcm57xx module with activate_gpio param, after it has failed to load switch_robo and switch_adm. Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11471 3c298f89-4303-0410-b956-a3cf2f4a3e73
2008-06-15 14:11:28 +03:00
#
# Copyright (C) 2006 OpenWrt.org
#
# This is free software, licensed under the GNU General Public License v2.
# See /LICENSE for more information.
#
# $Id: Makefile 8694 2007-09-08 19:55:42Z nbd $
include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/kernel.mk
PKG_NAME:=broadcom-57xx
PKG_RELEASE:=1
include $(INCLUDE_DIR)/package.mk
define KernelPackage/brcm-57xx
SUBMENU:=Network Devices
DEPENDS:=@TARGET_brcm_2_4 +kmod-switch
TITLE:=Broadcom 57xx ethernet support
FILES:=$(PKG_BUILD_DIR)/bcm57xx.$(LINUX_KMOD_SUFFIX)
AUTOLOAD:=$(call AutoLoad,30,bcm57xx)
endef
define Build/Prepare
mkdir -p $(PKG_BUILD_DIR)
$(CP) ./src/* $(PKG_BUILD_DIR)/
endef
ifeq ($(BOARD),brcm-2.4)
[package] replace some -I & -L flags with $(TARGET_CPPFLAGS) & $(TARGET_LDFLAGS) when appropriate git-svn-id: svn://svn.openwrt.org/openwrt/trunk@14651 3c298f89-4303-0410-b956-a3cf2f4a3e73
2009-02-24 02:08:08 +02:00
BUILDFLAGS := \
-DBCMDRIVER -I$(LINUX_DIR)/arch/mips/bcm947xx/include $(TARGET_CPPFLAGS) \
-DDBG=0 -DBCM_PROC_FS=1 -DT3_JUMBO_RCV_RCB_ENTRY_COUNT=256 -DNICE_SUPPORT \
-DPCIX_TARGET_WORKAROUND=1 -DINCLUDE_TBI_SUPPORT=1 -DINCLUDE_5701_AX_FIX=1
(6/6) bcm57xx: package This is the bcm57xx package. I have tested default vlan functions, but I dont have the equipment to test more advanced setups. The default vlan setup seems to be working fine. I also added the activate_gpio parameter which will make the driver activate the switch via gpio before probing for it. I'm not sure which method is best for autoload. For the wrt350n, I need the activate_gpio parameter. But its probably not a good idea to add that to the autoload file. On a system without a bcm57xx switch, isn't it a bad idea to mess with the gpios looking for the switch? Ideally, wouldn't it be best to load the bcm57xx module from broadcom-diag, after it has determined which router its on? I tried using 'request_module' from there, but had no success. For now, I am relying on preinit to load the bcm57xx module with activate_gpio param, after it has failed to load switch_robo and switch_adm. Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11471 3c298f89-4303-0410-b956-a3cf2f4a3e73
2008-06-15 14:11:28 +03:00
endif
define Build/Compile
$(MAKE) -C "$(LINUX_DIR)" \
CROSS_COMPILE="$(TARGET_CROSS)" \
ARCH="$(LINUX_KARCH)" \
SUBDIRS="$(PKG_BUILD_DIR)" \
EXTRA_CFLAGS="$(BUILDFLAGS)" \
modules
endef
define KernelPackage/brcm-57xx/install
$(call Package/brcm-57xx/install/Default,$(1))
#$(INSTALL_DIR) $(1)/etc/modules.d
#echo "bcm57xx activate_gpio=1" > $(1)/etc/modules.d/30-bcm57xx
endef
$(eval $(call KernelPackage,brcm-57xx))
Copy Permalink