1
0
mirror of git://projects.qi-hardware.com/openwrt-xburst.git synced 2024-12-21 06:10:50 +02:00
openwrt-xburst/target/linux/amazon-2.6/files/include/asm-mips/amazon/adm6996.h

233 lines
8.1 KiB
C
Raw Normal View History

/******************************************************************************
Copyright (c) 2004, Infineon Technologies. All rights reserved.
No Warranty
Because the program is licensed free of charge, there is no warranty for
the program, to the extent permitted by applicable law. Except when
otherwise stated in writing the copyright holders and/or other parties
provide the program "as is" without warranty of any kind, either
expressed or implied, including, but not limited to, the implied
warranties of merchantability and fitness for a particular purpose. The
entire risk as to the quality and performance of the program is with
you. should the program prove defective, you assume the cost of all
necessary servicing, repair or correction.
In no event unless required by applicable law or agreed to in writing
will any copyright holder, or any other party who may modify and/or
redistribute the program as permitted above, be liable to you for
damages, including any general, special, incidental or consequential
damages arising out of the use or inability to use the program
(including but not limited to loss of data or data being rendered
inaccurate or losses sustained by you or third parties or a failure of
the program to operate with any other programs), even if such holder or
other party has been advised of the possibility of such damages.
******************************************************************************
Module : ifx_swdrv.h
Date : 2004-09-01
Description : JoeLin
Remarks:
*****************************************************************************/
#ifndef _ADM_6996_MODULE_H_
#define _ADM_6996_MODULE_H_
#include <asm/amazon/amazon.h>
#define ifx_printf(x) printk x
/* command codes */
#define ADM_SW_SMI_READ 0x02
#define ADM_SW_SMI_WRITE 0x01
#define ADM_SW_SMI_START 0x01
#define ADM_SW_EEPROM_WRITE 0x01
#define ADM_SW_EEPROM_WRITE_ENABLE 0x03
#define ADM_SW_EEPROM_WRITE_DISABLE 0x00
#define EEPROM_TYPE 8 /* for 93C66 */
/* bit masks */
#define ADM_SW_BIT_MASK_1 0x00000001
#define ADM_SW_BIT_MASK_2 0x00000002
#define ADM_SW_BIT_MASK_4 0x00000008
#define ADM_SW_BIT_MASK_10 0x00000200
#define ADM_SW_BIT_MASK_16 0x00008000
#define ADM_SW_BIT_MASK_32 0x80000000
/* delay timers */
#define ADM_SW_MDC_DOWN_DELAY 5
#define ADM_SW_MDC_UP_DELAY 5
#define ADM_SW_CS_DELAY 5
/* MDIO modes */
#define ADM_SW_MDIO_OUTPUT 1
#define ADM_SW_MDIO_INPUT 0
#define ADM_SW_MAX_PORT_NUM 5
#define ADM_SW_MAX_VLAN_NUM 15
/* registers */
#define ADM_SW_PORT0_CONF 0x1
#define ADM_SW_PORT1_CONF 0x3
#define ADM_SW_PORT2_CONF 0x5
#define ADM_SW_PORT3_CONF 0x7
#define ADM_SW_PORT4_CONF 0x8
#define ADM_SW_PORT5_CONF 0x9
#define ADM_SW_VLAN_MODE 0x11
#define ADM_SW_MAC_LOCK 0x12
#define ADM_SW_VLAN0_CONF 0x13
#define ADM_SW_PORT0_PVID 0x28
#define ADM_SW_PORT1_PVID 0x29
#define ADM_SW_PORT2_PVID 0x2a
#define ADM_SW_PORT34_PVID 0x2b
#define ADM_SW_PORT5_PVID 0x2c
#define ADM_SW_PHY_RESET 0x2f
#define ADM_SW_MISC_CONF 0x30
#define ADM_SW_BNDWDH_CTL0 0x31
#define ADM_SW_BNDWDH_CTL1 0x32
#define ADM_SW_BNDWDH_CTL_ENA 0x33
/* port modes */
#define ADM_SW_PORT_FLOWCTL 0x1 /* 802.3x flow control */
#define ADM_SW_PORT_AN 0x2 /* auto negotiation */
#define ADM_SW_PORT_100M 0x4 /* 100M */
#define ADM_SW_PORT_FULL 0x8 /* full duplex */
#define ADM_SW_PORT_TAG 0x10 /* output tag on */
#define ADM_SW_PORT_DISABLE 0x20 /* disable port */
#define ADM_SW_PORT_TOS 0x40 /* TOS first */
#define ADM_SW_PORT_PPRI 0x80 /* port based priority first */
#define ADM_SW_PORT_MDIX 0x8000 /* auto MDIX on */
#define ADM_SW_PORT_PVID_SHIFT 10
#define ADM_SW_PORT_PVID_BITS 4
/* VLAN */
#define ADM_SW_VLAN_PORT0 0x1
#define ADM_SW_VLAN_PORT1 0x2
#define ADM_SW_VLAN_PORT2 0x10
#define ADM_SW_VLAN_PORT3 0x40
#define ADM_SW_VLAN_PORT4 0x80
#define ADM_SW_VLAN_PORT5 0x100
/* GPIO 012 enabled, output mode */
#define GPIO_ENABLEBITS 0x000700f8
/*
define AMAZON GPIO port to ADM6996 EEPROM interface
MDIO -> EEDI GPIO 16, AMAZON GPIO P1.0, bi-direction
MDC -> EESK GPIO 17, AMAZON GPIO P1.1, output only
MDCS -> EECS GPIO 18, AMAZON GPIO P1.2, output only
EEDO GPIO 15, AMAZON GPIO P0.15, do not need this one! */
#define GPIO_MDIO 1 //P1.0
#define GPIO_MDC 2 //P1.1
#define GPIO_MDCS 4 //P1.2
//joelin #define GPIO_MDIO 0
//joelin #define GPIO_MDC 5 /* PORT 0 GPIO5 */
//joelin #define GPIO_MDCS 6 /* PORT 0 GPIO6 */
#define MDIO_INPUT 0x00000001
#define MDIO_OUTPUT_EN 0x00010000
/* type definitions */
typedef unsigned char U8;
typedef unsigned short U16;
typedef unsigned int U32;
typedef struct _REGRW_
{
unsigned int addr;
unsigned int value;
unsigned int mode;
}REGRW, *PREGRW;
//joelin adm6996i
typedef struct _MACENTRY_
{
unsigned char mac_addr[6];
unsigned long fid:4;
unsigned long portmap:6;
union {
unsigned long age_timer:9;
unsigned long info_ctrl:9;
} ctrl;
unsigned long occupy:1;
unsigned long info_type:1;
unsigned long bad:1;
unsigned long result:3;//000:command ok ,001:all entry used,010:Entry Not found ,011:try next entry ,101:command error
}MACENTRY, *PMACENTRY;
typedef struct _PROTOCOLFILTER_
{
int protocol_filter_num;//[0~7]
int ip_p; //Value Compared with Protocol in IP Heade[7:0]
char action:2;//Action for protocol Filter .
//00 = Protocol Portmap is Default Output Ports.
//01 = Protocol Portmap is 6'b0.
//10 = Protocol Portmap is the CPU port if the incoming port
//is not the CPU port. But if the incoming port is the CPU port, then Type Portmap contains Default Output Ports, excluding the CPU port.
}PROTOCOLFILTER, *PPROTOCOLFILTER;
//joelin adm6996i
/* Santosh: for IGMP proxy/snooping */
//050614:fchang int adm_process_mac_table_request (unsigned int cmd, struct _MACENTRY_ *mac);
//050614:fchang int adm_process_protocol_filter_request (unsigned int cmd, struct _PROTOCOLFILTER_ *filter);
/* IOCTL keys */
#define KEY_IOCTL_ADM_REGRW 0x01
#define KEY_IOCTL_ADM_SW_REGRW 0x02
#define KEY_IOCTL_ADM_SW_PORTSTS 0x03
#define KEY_IOCTL_ADM_SW_INIT 0x04
//for adm6996i-start
#define KEY_IOCTL_ADM_SW_IOCTL_MACENTRY_ADD 0x05
#define KEY_IOCTL_ADM_SW_IOCTL_MACENTRY_DEL 0x06
#define KEY_IOCTL_ADM_SW_IOCTL_MACENTRY_GET_INIT 0x07
#define KEY_IOCTL_ADM_SW_IOCTL_MACENTRY_GET_MORE 0x08
#define KEY_IOCTL_ADM_SW_IOCTL_FILTER_ADD 0x09
#define KEY_IOCTL_ADM_SW_IOCTL_FILTER_DEL 0x0a
#define KEY_IOCTL_ADM_SW_IOCTL_FILTER_GET 0x0b
//adm6996i #define KEY_IOCTL_MAX_KEY 0x05
#define KEY_IOCTL_MAX_KEY 0x0c
//for adm6996i-end
/* IOCTL MAGIC */
#define ADM_MAGIC ('a'|'d'|'m'|'t'|'e'|'k')
/* IOCTL parameters */
#define ADM_IOCTL_REGRW _IOWR(ADM_MAGIC, KEY_IOCTL_ADM_REGRW, REGRW)
#define ADM_SW_IOCTL_REGRW _IOWR(ADM_MAGIC, KEY_IOCTL_ADM_SW_REGRW, REGRW)
#define ADM_SW_IOCTL_PORTSTS _IOWR(ADM_MAGIC, KEY_IOCTL_ADM_SW_PORTSTS, NULL)
#define ADM_SW_IOCTL_INIT _IOWR(ADM_MAGIC, KEY_IOCTL_ADM_SW_INIT, NULL)
//6996i-stat
#define ADM_SW_IOCTL_MACENTRY_ADD _IOWR(ADM_MAGIC, KEY_IOCTL_ADM_SW_IOCTL_MACENTRY_ADD,MACENTRY)
#define ADM_SW_IOCTL_MACENTRY_DEL _IOWR(ADM_MAGIC, KEY_IOCTL_ADM_SW_IOCTL_MACENTRY_DEL,MACENTRY)
#define ADM_SW_IOCTL_MACENTRY_GET_INIT _IOWR(ADM_MAGIC, KEY_IOCTL_ADM_SW_IOCTL_MACENTRY_GET_INIT,MACENTRY)
#define ADM_SW_IOCTL_MACENTRY_GET_MORE _IOWR(ADM_MAGIC, KEY_IOCTL_ADM_SW_IOCTL_MACENTRY_GET_MORE,MACENTRY)
#define ADM_SW_IOCTL_FILTER_ADD _IOWR(ADM_MAGIC, KEY_IOCTL_ADM_SW_IOCTL_FILTER_ADD,PROTOCOLFILTER)
#define ADM_SW_IOCTL_FILTER_DEL _IOWR(ADM_MAGIC, KEY_IOCTL_ADM_SW_IOCTL_FILTER_DEL,PROTOCOLFILTER)
#define ADM_SW_IOCTL_FILTER_GET _IOWR(ADM_MAGIC, KEY_IOCTL_ADM_SW_IOCTL_FILTER_GET,PROTOCOLFILTER)
//6996i-end
#define REG_READ 0x0
#define REG_WRITE 0x1
/* undefine symbol */
#define AMAZON_SW_REG(reg) *((volatile U32*)(reg))
//#define GPIO0_INPUT_MASK 0
//#define GPIO_conf0_REG 0x12345678
//#define GPIO_SET_HI
//#define GPIO_SET_LOW
#endif
/* _ADM_6996_MODULE_H_ */