1
0
mirror of git://projects.qi-hardware.com/openwrt-xburst.git synced 2024-12-25 10:45:11 +02:00

ixp4xx patches cleanup, round one

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11619 3c298f89-4303-0410-b956-a3cf2f4a3e73
This commit is contained in:
kaloz 2008-07-02 21:37:46 +00:00
parent f7bdd481d2
commit 022e126a6b
17 changed files with 345 additions and 320 deletions

View File

@ -1,50 +1,3 @@
From: Rod Whitby <rod@whitby.id.au>
Subject: [PATCH] ixp4xx: Add support for the Freecom FSG-3 board (Patch #4874)
The Freecom-FSG3 is a small network-attached-storage device with the
following feature set:
* Intel IXP422
* 4MB Flash (ixp4xx flash driver)
* 64MB RAM
* 4 USB 2.0 host ports (ehci and ohci drivers)
* 1 WAN (eth1) and 3 LAN (eth0) ethernet ports
* Supported by the open source ixp4xx ethernet driver
* Via VT6421 disk controller (libata and sata-via drivers)
* Internal hard disk (PATA supported, SATA not yet supported)
* External SATA port (not yet supported)
* ISL1208 RTC chip
* Winbond 83782 temp sensor and fan controller
* MiniPCI slot
The ixp4xx_defconfig is also updated to support this device (the
leds-fsg driver is to be submitted separately via the leds tree after
this initial support is merged, as it depends on header gpio defines).
Signed-off-by: Rod Whitby <rod@whitby.id.au>
PATCH FOLLOWS
KernelVersion: v2.6.25-rc6-74-g264e3e8
---
Updated to correct all issues found by RMK.
The front power button calls ctrl_alt_del() and the rear reset button
now calls machine_restart() directly.
arch/arm/configs/ixp4xx_defconfig | 9 +-
arch/arm/mach-ixp4xx/Kconfig | 9 +
arch/arm/mach-ixp4xx/Makefile | 2 +
arch/arm/mach-ixp4xx/fsg-pci.c | 71 ++++++++
arch/arm/mach-ixp4xx/fsg-setup.c | 276 ++++++++++++++++++++++++++++++++
include/asm-arm/arch-ixp4xx/fsg.h | 50 ++++++
include/asm-arm/arch-ixp4xx/hardware.h | 1 +
include/asm-arm/arch-ixp4xx/irqs.h | 7 +
8 files changed, 421 insertions(+), 4 deletions(-)
create mode 100644 arch/arm/mach-ixp4xx/fsg-pci.c
create mode 100644 arch/arm/mach-ixp4xx/fsg-setup.c
create mode 100644 include/asm-arm/arch-ixp4xx/fsg.h
--- a/arch/arm/configs/ixp4xx_defconfig --- a/arch/arm/configs/ixp4xx_defconfig
+++ b/arch/arm/configs/ixp4xx_defconfig +++ b/arch/arm/configs/ixp4xx_defconfig
@@ -165,6 +165,7 @@ @@ -165,6 +165,7 @@

View File

@ -1,40 +0,0 @@
--- a/arch/arm/mach-ixp4xx/gateway7001-setup.c
+++ b/arch/arm/mach-ixp4xx/gateway7001-setup.c
@@ -76,9 +76,36 @@
.resource = &gateway7001_uart_resource,
};
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info gateway7001_plat_eth[] = {
+ {
+ .phy = 1,
+ .rxq = 3,
+ .txreadyq = 20,
+ }, {
+ .phy = 2,
+ .rxq = 4,
+ .txreadyq = 21,
+ }
+};
+
+static struct platform_device gateway7001_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = gateway7001_plat_eth,
+ }, {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEC,
+ .dev.platform_data = gateway7001_plat_eth + 1,
+ }
+};
+
static struct platform_device *gateway7001_devices[] __initdata = {
&gateway7001_flash,
- &gateway7001_uart
+ &gateway7001_uart,
+ &gateway7001_eth[0],
+ &gateway7001_eth[1],
};
static void __init gateway7001_init(void)

View File

@ -0,0 +1,68 @@
--- a/arch/arm/mach-ixp4xx/gateway7001-setup.c
+++ b/arch/arm/mach-ixp4xx/gateway7001-setup.c
@@ -76,9 +76,35 @@
.resource = &gateway7001_uart_resource,
};
+static struct eth_plat_info gateway7001_plat_eth[] = {
+ {
+ .phy = 1,
+ .rxq = 3,
+ .txreadyq = 20,
+ }, {
+ .phy = 2,
+ .rxq = 4,
+ .txreadyq = 21,
+ }
+};
+
+static struct platform_device gateway7001_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = gateway7001_plat_eth,
+ }, {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEC,
+ .dev.platform_data = gateway7001_plat_eth + 1,
+ }
+};
+
static struct platform_device *gateway7001_devices[] __initdata = {
&gateway7001_flash,
- &gateway7001_uart
+ &gateway7001_uart,
+ &gateway7001_eth[0],
+ &gateway7001_eth[1],
};
static void __init gateway7001_init(void)
--- a/arch/arm/mach-ixp4xx/wg302v2-setup.c
+++ b/arch/arm/mach-ixp4xx/wg302v2-setup.c
@@ -77,9 +77,26 @@
.resource = &wg302v2_uart_resource,
};
+static struct eth_plat_info wg302v2_plat_eth[] = {
+ {
+ .phy = 8,
+ .rxq = 3,
+ .txreadyq = 20,
+ }
+};
+
+static struct platform_device wg302v2_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = wg302v2_plat_eth,
+ }
+};
+
static struct platform_device *wg302v2_devices[] __initdata = {
&wg302v2_flash,
&wg302v2_uart,
+ &wg302v2_eth[0],
};
static void __init wg302v2_init(void)

View File

@ -1,30 +0,0 @@
--- a/arch/arm/mach-ixp4xx/wg302v2-setup.c
+++ b/arch/arm/mach-ixp4xx/wg302v2-setup.c
@@ -77,9 +77,27 @@
.resource = &wg302v2_uart_resource,
};
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info wg302_plat_eth[] = {
+ {
+ .phy = 8,
+ .rxq = 3,
+ .txreadyq = 20,
+ }
+};
+
+static struct platform_device wg302_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = wg302_plat_eth,
+ }
+};
+
static struct platform_device *wg302v2_devices[] __initdata = {
&wg302v2_flash,
&wg302v2_uart,
+ &wg302_eth[0],
};
static void __init wg302v2_init(void)

View File

@ -1,3 +1,13 @@
--- a/arch/arm/configs/ixp4xx_defconfig
+++ b/arch/arm/configs/ixp4xx_defconfig
@@ -155,6 +155,7 @@
CONFIG_MACH_LOFT=y
CONFIG_ARCH_ADI_COYOTE=y
CONFIG_MACH_GATEWAY7001=y
+CONFIG_MACH_WG302V1=y
CONFIG_MACH_WG302V2=y
CONFIG_ARCH_IXDP425=y
CONFIG_MACH_IXDPG425=y
--- a/arch/arm/mach-ixp4xx/Kconfig --- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig +++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -49,6 +49,14 @@ @@ -49,6 +49,14 @@
@ -24,18 +34,18 @@
+obj-pci-$(CONFIG_MACH_WG302V1) += wg302v1-pci.o +obj-pci-$(CONFIG_MACH_WG302V1) += wg302v1-pci.o
obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o
obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o
obj-pci-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-pci.o
@@ -33,6 +34,7 @@ @@ -28,6 +29,7 @@
obj-$(CONFIG_MACH_NAS100D) += nas100d-setup.o obj-$(CONFIG_MACH_NAS100D) += nas100d-setup.o
obj-$(CONFIG_MACH_DSMG600) += dsmg600-setup.o obj-$(CONFIG_MACH_DSMG600) += dsmg600-setup.o
obj-$(CONFIG_MACH_GATEWAY7001) += gateway7001-setup.o obj-$(CONFIG_MACH_GATEWAY7001) += gateway7001-setup.o
+obj-$(CONFIG_MACH_WG302V1) += wg302v1-setup.o +obj-$(CONFIG_MACH_WG302V1) += wg302v1-setup.o
obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o
obj-$(CONFIG_MACH_FSG) += fsg-setup.o obj-$(CONFIG_MACH_FSG) += fsg-setup.o
obj-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-setup.o
--- /dev/null --- /dev/null
+++ b/arch/arm/mach-ixp4xx/wg302v1-pci.c +++ b/arch/arm/mach-ixp4xx/wg302v1-pci.c
@@ -0,0 +1,63 @@ @@ -0,0 +1,64 @@
+/* +/*
+ * arch/arch/mach-ixp4xx/wg302v1-pci.c + * arch/arch/mach-ixp4xx/wg302v1-pci.c
+ * + *
@ -79,7 +89,8 @@
+ return IRQ_IXP4XX_GPIO8; + return IRQ_IXP4XX_GPIO8;
+ else if (slot == 2) + else if (slot == 2)
+ return IRQ_IXP4XX_GPIO10; + return IRQ_IXP4XX_GPIO10;
+ else return -1; + else
+ return -1;
+} +}
+ +
+struct hw_pci wg302v1_pci __initdata = { +struct hw_pci wg302v1_pci __initdata = {
@ -101,7 +112,7 @@
+subsys_initcall(wg302v1_pci_init); +subsys_initcall(wg302v1_pci_init);
--- /dev/null --- /dev/null
+++ b/arch/arm/mach-ixp4xx/wg302v1-setup.c +++ b/arch/arm/mach-ixp4xx/wg302v1-setup.c
@@ -0,0 +1,109 @@ @@ -0,0 +1,126 @@
+/* +/*
+ * arch/arm/mach-ixp4xx/wg302v1-setup.c + * arch/arm/mach-ixp4xx/wg302v1-setup.c
+ * + *
@ -123,10 +134,10 @@
+#include <linux/tty.h> +#include <linux/tty.h>
+#include <linux/serial_8250.h> +#include <linux/serial_8250.h>
+#include <linux/slab.h> +#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/memory.h>
+ +
+#include <asm/types.h>
+#include <asm/setup.h> +#include <asm/setup.h>
+#include <asm/memory.h>
+#include <asm/hardware.h> +#include <asm/hardware.h>
+#include <asm/irq.h> +#include <asm/irq.h>
+#include <asm/mach-types.h> +#include <asm/mach-types.h>
@ -181,9 +192,26 @@
+ .resource = &wg302v1_uart_resource, + .resource = &wg302v1_uart_resource,
+}; +};
+ +
+static struct eth_plat_info wg302v1_plat_eth[] = {
+ {
+ .phy = 30,
+ .rxq = 3,
+ .txreadyq = 20,
+ }
+};
+
+static struct platform_device wg302v1_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = wg302v1_plat_eth,
+ }
+};
+
+static struct platform_device *wg302v1_devices[] __initdata = { +static struct platform_device *wg302v1_devices[] __initdata = {
+ &wg302v1_flash, + &wg302v1_flash,
+ &wg302v1_uart, + &wg302v1_uart,
+ &wg302v1_eth[0],
+}; +};
+ +
+static void __init wg302v1_init(void) +static void __init wg302v1_init(void)

View File

@ -1,47 +1,68 @@
--- a/arch/arm/configs/ixp4xx_defconfig
+++ b/arch/arm/configs/ixp4xx_defconfig
@@ -157,6 +157,8 @@
CONFIG_MACH_GATEWAY7001=y
CONFIG_MACH_WG302V1=y
CONFIG_MACH_WG302V2=y
+CONFIG_MACH_PRONGHORN=y
+CONFIG_MACH_PRONGHORNMETRO=y
CONFIG_ARCH_IXDP425=y
CONFIG_MACH_IXDPG425=y
CONFIG_MACH_IXDP465=y
--- a/arch/arm/mach-ixp4xx/Kconfig --- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig +++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -57,6 +57,14 @@ @@ -65,6 +65,24 @@
WG302 v2 or WAG302 v2 Access Points. For more information WG302 v2 or WAG302 v2 Access Points. For more information
on this platform, see http://openwrt.org on this platform, see http://openwrt.org
+config MACH_PRONGHORNMETRO +config MACH_PRONGHORN
+ bool "Pronghorn Metro" + bool "ADI Pronghorn series"
+ select PCI + select PCI
+ help + help
+ Say 'Y' here if you want your kernel to support the ADI + Say 'Y' here if you want your kernel to support the ADI
+ Engineering Pronghorn Metro Platform. For more + Engineering Pronghorn series. For more
+ information on this platform, see <file:Documentation/arm/IXP4xx>. + information on this platform, see http://www.adiengineering.com
+
+#
+# There're only minimal differences kernel-wise between the Pronghorn and
+# Pronghorn Metro boards - they use different chip selects to drive the
+# CF slot connected to the expansion bus, so we just enable them together.
+#
+config MACH_PRONGHORNMETRO
+ bool
+ depends on MACH_PRONGHORN
+ default y
+ +
config ARCH_IXDP425 config ARCH_IXDP425
bool "IXDP425" bool "IXDP425"
help help
--- a/arch/arm/mach-ixp4xx/Makefile --- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile +++ b/arch/arm/mach-ixp4xx/Makefile
@@ -16,6 +16,7 @@ @@ -17,6 +17,7 @@
obj-pci-$(CONFIG_MACH_GATEWAY7001) += gateway7001-pci.o obj-pci-$(CONFIG_MACH_WG302V1) += wg302v1-pci.o
obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o
obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o
+obj-pci-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-pci.o +obj-pci-$(CONFIG_MACH_PRONGHORN) += pronghorn-pci.o
obj-y += common.o obj-y += common.o
@@ -30,6 +31,7 @@ @@ -32,6 +33,7 @@
obj-$(CONFIG_MACH_GATEWAY7001) += gateway7001-setup.o obj-$(CONFIG_MACH_WG302V1) += wg302v1-setup.o
obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o
obj-$(CONFIG_MACH_FSG) += fsg-setup.o obj-$(CONFIG_MACH_FSG) += fsg-setup.o
+obj-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-setup.o +obj-$(CONFIG_MACH_PRONGHORN) += pronghorn-setup.o
obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o
obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o
--- /dev/null --- /dev/null
+++ b/arch/arm/mach-ixp4xx/pronghornmetro-pci.c +++ b/arch/arm/mach-ixp4xx/pronghorn-pci.c
@@ -0,0 +1,74 @@ @@ -0,0 +1,70 @@
+/* +/*
+ * arch/arch/mach-ixp4xx/pronghornmetro-pci.c + * arch/arch/mach-ixp4xx/pronghorn-pci.c
+ * + *
+ * PCI setup routines for ADI Engineering Pronghorn Metro + * PCI setup routines for ADI Engineering Pronghorn series
+ * + *
+ * Copyright (C) 2007 Imre Kaloz <kaloz@openwrt.org> + * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ * + *
+ * based on coyote-pci.c: + * based on coyote-pci.c:
+ * Copyright (C) 2002 Jungo Software Technologies. + * Copyright (C) 2002 Jungo Software Technologies.
@ -62,15 +83,10 @@
+ +
+#include <asm/mach-types.h> +#include <asm/mach-types.h>
+#include <asm/hardware.h> +#include <asm/hardware.h>
+#include <asm/irq.h>
+ +
+#include <asm/mach/pci.h> +#include <asm/mach/pci.h>
+ +
+extern void ixp4xx_pci_preinit(void); +void __init pronghorn_pci_preinit(void)
+extern int ixp4xx_setup(int nr, struct pci_sys_data *sys);
+extern struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys);
+
+void __init pronghornmetro_pci_preinit(void)
+{ +{
+ set_irq_type(IRQ_IXP4XX_GPIO4, IRQT_LOW); + set_irq_type(IRQ_IXP4XX_GPIO4, IRQT_LOW);
+ set_irq_type(IRQ_IXP4XX_GPIO6, IRQT_LOW); + set_irq_type(IRQ_IXP4XX_GPIO6, IRQT_LOW);
@ -80,7 +96,7 @@
+ ixp4xx_pci_preinit(); + ixp4xx_pci_preinit();
+} +}
+ +
+static int __init pronghornmetro_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +static int __init pronghorn_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{ +{
+ if (slot == 13) + if (slot == 13)
+ return IRQ_IXP4XX_GPIO4; + return IRQ_IXP4XX_GPIO4;
@ -90,35 +106,36 @@
+ return IRQ_IXP4XX_GPIO11; + return IRQ_IXP4XX_GPIO11;
+ else if (slot == 16) + else if (slot == 16)
+ return IRQ_IXP4XX_GPIO1; + return IRQ_IXP4XX_GPIO1;
+ else return -1; + else
+ return -1;
+} +}
+ +
+struct hw_pci pronghornmetro_pci __initdata = { +struct hw_pci pronghorn_pci __initdata = {
+ .nr_controllers = 1, + .nr_controllers = 1,
+ .preinit = pronghornmetro_pci_preinit, + .preinit = pronghorn_pci_preinit,
+ .swizzle = pci_std_swizzle, + .swizzle = pci_std_swizzle,
+ .setup = ixp4xx_setup, + .setup = ixp4xx_setup,
+ .scan = ixp4xx_scan_bus, + .scan = ixp4xx_scan_bus,
+ .map_irq = pronghornmetro_map_irq, + .map_irq = pronghorn_map_irq,
+}; +};
+ +
+int __init pronghornmetro_pci_init(void) +int __init pronghorn_pci_init(void)
+{ +{
+ if (machine_is_pronghorn_metro()) + if (machine_is_pronghorn() || machine_is_pronghorn_metro())
+ pci_common_init(&pronghornmetro_pci); + pci_common_init(&pronghorn_pci);
+ return 0; + return 0;
+} +}
+ +
+subsys_initcall(pronghornmetro_pci_init); +subsys_initcall(pronghorn_pci_init);
--- /dev/null --- /dev/null
+++ b/arch/arm/mach-ixp4xx/pronghornmetro-setup.c +++ b/arch/arm/mach-ixp4xx/pronghorn-setup.c
@@ -0,0 +1,147 @@ @@ -0,0 +1,245 @@
+/* +/*
+ * arch/arm/mach-ixp4xx/pronghornmetro-setup.c + * arch/arm/mach-ixp4xx/pronghorn-setup.c
+ * + *
+ * Board setup for the ADI Engineering Pronghorn Metro + * Board setup for the ADI Engineering Pronghorn series
+ * + *
+ * Copyright (C) 2007 Imre Kaloz <Kaloz@openwrt.org> + * Copyright (C) 2008 Imre Kaloz <Kaloz@openwrt.org>
+ * + *
+ * based on coyote-setup.c: + * based on coyote-setup.c:
+ * Copyright (C) 2003-2005 MontaVista Software, Inc. + * Copyright (C) 2003-2005 MontaVista Software, Inc.
@ -133,42 +150,59 @@
+#include <linux/tty.h> +#include <linux/tty.h>
+#include <linux/serial_8250.h> +#include <linux/serial_8250.h>
+#include <linux/slab.h> +#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/memory.h>
+#include <linux/i2c-gpio.h>
+ +
+#include <asm/types.h>
+#include <asm/setup.h> +#include <asm/setup.h>
+#include <asm/memory.h>
+#include <asm/hardware.h> +#include <asm/hardware.h>
+#include <asm/irq.h> +#include <asm/irq.h>
+#include <asm/mach-types.h> +#include <asm/mach-types.h>
+#include <asm/mach/arch.h> +#include <asm/mach/arch.h>
+#include <asm/mach/flash.h> +#include <asm/mach/flash.h>
+ +
+static struct flash_platform_data pronghornmetro_flash_data = { +static struct flash_platform_data pronghorn_flash_data = {
+ .map_name = "cfi_probe", + .map_name = "cfi_probe",
+ .width = 2, + .width = 2,
+}; +};
+ +
+static struct resource pronghornmetro_flash_resource = { +static struct resource pronghorn_flash_resource = {
+ .flags = IORESOURCE_MEM, + .flags = IORESOURCE_MEM,
+}; +};
+ +
+static struct platform_device pronghornmetro_flash = { +static struct platform_device pronghorn_flash = {
+ .name = "IXP4XX-Flash", + .name = "IXP4XX-Flash",
+ .id = 0, + .id = 0,
+ .dev = { + .dev = {
+ .platform_data = &pronghornmetro_flash_data, + .platform_data = &pronghorn_flash_data,
+ }, + },
+ .num_resources = 1, + .num_resources = 1,
+ .resource = &pronghornmetro_flash_resource, + .resource = &pronghorn_flash_resource,
+}; +};
+ +
+static struct resource pronghornmetro_uart_resource = { +static struct resource pronghorn_uart_resources [] = {
+ .start = IXP4XX_UART2_BASE_PHYS, + {
+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, + .start = IXP4XX_UART1_BASE_PHYS,
+ .flags = IORESOURCE_MEM, + .end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM
+ },
+ {
+ .start = IXP4XX_UART2_BASE_PHYS,
+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM
+ }
+}; +};
+ +
+static struct plat_serial8250_port pronghornmetro_uart_data[] = { +static struct plat_serial8250_port pronghorn_uart_data[] = {
+ {
+ .mapbase = IXP4XX_UART1_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART1,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ { + {
+ .mapbase = IXP4XX_UART2_BASE_PHYS, + .mapbase = IXP4XX_UART2_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, + .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
@ -181,17 +215,49 @@
+ { }, + { },
+}; +};
+ +
+static struct platform_device pronghornmetro_uart = { +static struct platform_device pronghorn_uart = {
+ .name = "serial8250", + .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM, + .id = PLAT8250_DEV_PLATFORM,
+ .dev = { + .dev = {
+ .platform_data = pronghornmetro_uart_data, + .platform_data = pronghorn_uart_data,
+ }, + },
+ .num_resources = 1, + .num_resources = 2,
+ .resource = &pronghornmetro_uart_resource, + .resource = pronghorn_uart_resources,
+}; +};
+ +
+static struct resource pronghornmetro_pata_resources[] = { +static struct i2c_gpio_platform_data pronghorn_i2c_gpio_data = {
+ .sda_pin = 9,
+ .scl_pin = 10,
+};
+
+static struct platform_device pronghorn_i2c_gpio = {
+ .name = "i2c-gpio",
+ .id = 0,
+ .dev = {
+ .platform_data = &pronghorn_i2c_gpio_data,
+ },
+};
+
+static struct gpio_led pronghorn_led_pin[] = {
+ {
+ .name = "pronghorn:green:status",
+ .gpio = 7,
+ },
+ { },
+};
+
+static struct gpio_led_platform_data pronghorn_led_data = {
+ .num_leds = ARRAY_SIZE(pronghorn_led_pin),
+ .leds = pronghorn_led_pin,
+};
+
+static struct platform_device pronghorn_led = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev.platform_data = &pronghorn_led_data,
+};
+
+static struct resource pronghorn_pata_resources[] = {
+ { + {
+ .flags = IORESOURCE_MEM + .flags = IORESOURCE_MEM
+ }, + },
@ -206,49 +272,99 @@
+ }, + },
+}; +};
+ +
+static struct ixp4xx_pata_data pronghornmetro_pata_data = { +static struct ixp4xx_pata_data pronghorn_pata_data = {
+ .cs0_bits = 0xbfff0043, + .cs0_bits = 0xbfff0043,
+ .cs1_bits = 0xbfff0043, + .cs1_bits = 0xbfff0043,
+}; +};
+ +
+static struct platform_device pronghornmetro_pata = { +static struct platform_device pronghorn_pata = {
+ .name = "pata_ixp4xx_cf", + .name = "pata_ixp4xx_cf",
+ .id = 0, + .id = 0,
+ .dev.platform_data = &pronghornmetro_pata_data, + .dev.platform_data = &pronghorn_pata_data,
+ .num_resources = ARRAY_SIZE(pronghornmetro_pata_resources), + .num_resources = ARRAY_SIZE(pronghorn_pata_resources),
+ .resource = pronghornmetro_pata_resources, + .resource = pronghorn_pata_resources,
+}; +};
+ +
+static struct platform_device *pronghornmetro_devices[] __initdata = { +static struct eth_plat_info pronghorn_plat_eth[] = {
+ &pronghornmetro_flash, + {
+ &pronghornmetro_uart, + .phy = 0,
+ .rxq = 3,
+ .txreadyq = 20,
+ }, {
+ .phy = 1,
+ .rxq = 4,
+ .txreadyq = 21,
+ }
+}; +};
+ +
+static void __init pronghornmetro_init(void) +static struct platform_device pronghorn_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = pronghorn_plat_eth,
+ }, {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEC,
+ .dev.platform_data = pronghorn_plat_eth + 1,
+ }
+};
+
+static struct platform_device *pronghorn_devices[] __initdata = {
+ &pronghorn_flash,
+ &pronghorn_uart,
+ &pronghorn_led,
+ &pronghorn_eth[0],
+ &pronghorn_eth[1],
+};
+
+static void __init pronghorn_init(void)
+{ +{
+ ixp4xx_sys_init(); + ixp4xx_sys_init();
+ +
+ pronghornmetro_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); + pronghorn_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+ pronghornmetro_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_16M - 1; + pronghorn_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_16M - 1;
+ +
+ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; + *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
+ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; + *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+ +
+ platform_add_devices(pronghornmetro_devices, ARRAY_SIZE(pronghornmetro_devices)); + platform_add_devices(pronghorn_devices, ARRAY_SIZE(pronghorn_devices));
+ +
+ pronghornmetro_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(1); + if (machine_is_pronghorn()) {
+ pronghornmetro_pata_resources[0].end = IXP4XX_EXP_BUS_END(1); + pronghorn_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(3);
+ pronghorn_pata_resources[0].end = IXP4XX_EXP_BUS_END(3);
+ +
+ pronghornmetro_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(2); + pronghorn_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(4);
+ pronghornmetro_pata_resources[1].end = IXP4XX_EXP_BUS_END(2); + pronghorn_pata_resources[1].end = IXP4XX_EXP_BUS_END(4);
+ +
+ pronghornmetro_pata_data.cs0_cfg = IXP4XX_EXP_CS1; + pronghorn_pata_data.cs0_cfg = IXP4XX_EXP_CS3;
+ pronghornmetro_pata_data.cs1_cfg = IXP4XX_EXP_CS2; + pronghorn_pata_data.cs1_cfg = IXP4XX_EXP_CS4;
+ } else {
+ pronghorn_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(2);
+ pronghorn_pata_resources[0].end = IXP4XX_EXP_BUS_END(2);
+ +
+ platform_device_register(&pronghornmetro_pata); + pronghorn_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(3);
+ pronghorn_pata_resources[1].end = IXP4XX_EXP_BUS_END(3);
+
+ pronghorn_pata_data.cs0_cfg = IXP4XX_EXP_CS2;
+ pronghorn_pata_data.cs1_cfg = IXP4XX_EXP_CS3;
+
+ platform_device_register(&pronghorn_i2c_gpio);
+ }
+
+ platform_device_register(&pronghorn_pata);
+} +}
+ +
+#ifdef CONFIG_MACH_PRONGHORNMETRO +MACHINE_START(PRONGHORN, "ADI Engineering Pronghorn")
+ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ .map_io = ixp4xx_map_io,
+ .init_irq = ixp4xx_init_irq,
+ .timer = &ixp4xx_timer,
+ .boot_params = 0x0100,
+ .init_machine = pronghorn_init,
+MACHINE_END
+
+MACHINE_START(PRONGHORNMETRO, "ADI Engineering Pronghorn Metro") +MACHINE_START(PRONGHORNMETRO, "ADI Engineering Pronghorn Metro")
+ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */ + /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, + .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
@ -257,21 +373,8 @@
+ .init_irq = ixp4xx_init_irq, + .init_irq = ixp4xx_init_irq,
+ .timer = &ixp4xx_timer, + .timer = &ixp4xx_timer,
+ .boot_params = 0x0100, + .boot_params = 0x0100,
+ .init_machine = pronghornmetro_init, + .init_machine = pronghorn_init,
+MACHINE_END +MACHINE_END
+#endif
--- a/Documentation/arm/IXP4xx
+++ b/Documentation/arm/IXP4xx
@@ -111,6 +111,9 @@
the platform has two mini-PCI slots used for 802.11[bga] cards.
Finally, there is an IDE port hanging off the expansion bus.
+ADI Engineering Pronghorn Metro Platform
+http://www.adiengineering.com/php-bin/ecomm4/productDisplay.php?category_id=30&product_id=85
+
Gateworks Avila Network Platform
http://www.gateworks.com/avila_sbc.htm
--- a/include/asm-arm/arch-ixp4xx/uncompress.h --- a/include/asm-arm/arch-ixp4xx/uncompress.h
+++ b/include/asm-arm/arch-ixp4xx/uncompress.h +++ b/include/asm-arm/arch-ixp4xx/uncompress.h
@@ -41,7 +41,8 @@ @@ -41,7 +41,8 @@
@ -280,7 +383,7 @@
if (machine_is_adi_coyote() || machine_is_gtwx5715() || if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
- machine_is_gateway7001() || machine_is_wg302v2()) - machine_is_gateway7001() || machine_is_wg302v2())
+ machine_is_gateway7001() || machine_is_wg302v2() || + machine_is_gateway7001() || machine_is_wg302v2() ||
+ machine_is_pronghorn_metro()) + machine_is_pronghorn() || machine_is_pronghorn_metro())
uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS; uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
else else
uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS; uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;

View File

@ -1,39 +0,0 @@
--- a/arch/arm/mach-ixp4xx/pronghornmetro-setup.c
+++ b/arch/arm/mach-ixp4xx/pronghornmetro-setup.c
@@ -104,9 +104,36 @@
.resource = pronghornmetro_pata_resources,
};
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info pronghornmetro_plat_eth[] = {
+ {
+ .phy = 0,
+ .rxq = 3,
+ .txreadyq = 20,
+ }, {
+ .phy = 1,
+ .rxq = 4,
+ .txreadyq = 21,
+ }
+};
+
+static struct platform_device pronghornmetro_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = pronghornmetro_plat_eth,
+ }, {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEC,
+ .dev.platform_data = pronghornmetro_plat_eth + 1,
+ }
+};
+
static struct platform_device *pronghornmetro_devices[] __initdata = {
&pronghornmetro_flash,
&pronghornmetro_uart,
+ &pronghornmetro_eth[0],
+ &pronghornmetro_eth[1],
};
static void __init pronghornmetro_init(void)

View File

@ -1,8 +1,8 @@
--- a/arch/arm/mach-ixp4xx/Kconfig --- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig +++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -65,6 +65,14 @@ @@ -83,6 +83,14 @@
Engineering Pronghorn Metro Platform. For more depends on MACH_PRONGHORN
information on this platform, see <file:Documentation/arm/IXP4xx>. default y
+config MACH_COMPEX +config MACH_COMPEX
+ bool "Compex WP18 / NP18A" + bool "Compex WP18 / NP18A"
@ -17,18 +17,18 @@
help help
--- a/arch/arm/mach-ixp4xx/Makefile --- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile +++ b/arch/arm/mach-ixp4xx/Makefile
@@ -17,6 +17,7 @@ @@ -18,6 +18,7 @@
obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o
obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o
obj-pci-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-pci.o obj-pci-$(CONFIG_MACH_PRONGHORN) += pronghorn-pci.o
+obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o +obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o
obj-y += common.o obj-y += common.o
@@ -32,6 +33,7 @@ @@ -34,6 +35,7 @@
obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o
obj-$(CONFIG_MACH_FSG) += fsg-setup.o obj-$(CONFIG_MACH_FSG) += fsg-setup.o
obj-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-setup.o obj-$(CONFIG_MACH_PRONGHORN) += pronghorn-setup.o
+obj-$(CONFIG_MACH_COMPEX) += compex-setup.o +obj-$(CONFIG_MACH_COMPEX) += compex-setup.o
obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o

View File

@ -1,6 +1,6 @@
--- a/arch/arm/mach-ixp4xx/Kconfig --- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig +++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -73,6 +73,14 @@ @@ -91,6 +91,14 @@
WP18 or NP18A boards. For more information on this WP18 or NP18A boards. For more information on this
platform, see http://openwrt.org platform, see http://openwrt.org
@ -17,17 +17,17 @@
help help
--- a/arch/arm/mach-ixp4xx/Makefile --- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile +++ b/arch/arm/mach-ixp4xx/Makefile
@@ -18,6 +18,7 @@ @@ -19,6 +19,7 @@
obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o
obj-pci-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-pci.o obj-pci-$(CONFIG_MACH_PRONGHORN) += pronghorn-pci.o
obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o
+obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o +obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o
obj-y += common.o obj-y += common.o
@@ -34,6 +35,7 @@ @@ -36,6 +37,7 @@
obj-$(CONFIG_MACH_FSG) += fsg-setup.o obj-$(CONFIG_MACH_FSG) += fsg-setup.o
obj-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-setup.o obj-$(CONFIG_MACH_PRONGHORN) += pronghorn-setup.o
obj-$(CONFIG_MACH_COMPEX) += compex-setup.o obj-$(CONFIG_MACH_COMPEX) += compex-setup.o
+obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o +obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o
@ -218,8 +218,8 @@
*/ */
if (machine_is_adi_coyote() || machine_is_gtwx5715() || if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
machine_is_gateway7001() || machine_is_wg302v2() || machine_is_gateway7001() || machine_is_wg302v2() ||
- machine_is_pronghorn_metro()) - machine_is_pronghorn() || machine_is_pronghorn_metro())
+ machine_is_pronghorn_metro() || machine_is_wrt300nv2()) + machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2())
uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS; uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
else else
uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS; uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;

View File

@ -1,8 +1,8 @@
--- a/arch/arm/mach-ixp4xx/Kconfig --- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig +++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -65,6 +65,14 @@ @@ -83,6 +83,14 @@
Engineering Pronghorn Metro Platform. For more depends on MACH_PRONGHORN
information on this platform, see <file:Documentation/arm/IXP4xx>. default y
+config MACH_SIDEWINDER +config MACH_SIDEWINDER
+ bool "Sidewinder" + bool "Sidewinder"
@ -15,7 +15,7 @@
config MACH_COMPEX config MACH_COMPEX
bool "Compex WP18 / NP18A" bool "Compex WP18 / NP18A"
select PCI select PCI
@@ -163,7 +171,7 @@ @@ -181,7 +189,7 @@
# #
config CPU_IXP46X config CPU_IXP46X
bool bool
@ -26,16 +26,16 @@
config CPU_IXP43X config CPU_IXP43X
--- a/arch/arm/mach-ixp4xx/Makefile --- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile +++ b/arch/arm/mach-ixp4xx/Makefile
@@ -19,6 +19,7 @@ @@ -20,6 +20,7 @@
obj-pci-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-pci.o obj-pci-$(CONFIG_MACH_PRONGHORN) += pronghorn-pci.o
obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o
obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o
+obj-pci-$(CONFIG_MACH_SIDEWINDER) += sidewinder-pci.o +obj-pci-$(CONFIG_MACH_SIDEWINDER) += sidewinder-pci.o
obj-y += common.o obj-y += common.o
@@ -36,6 +37,7 @@ @@ -38,6 +39,7 @@
obj-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-setup.o obj-$(CONFIG_MACH_PRONGHORN) += pronghorn-setup.o
obj-$(CONFIG_MACH_COMPEX) += compex-setup.o obj-$(CONFIG_MACH_COMPEX) += compex-setup.o
obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o
+obj-$(CONFIG_MACH_SIDEWINDER) += sidewinder-setup.o +obj-$(CONFIG_MACH_SIDEWINDER) += sidewinder-setup.o

View File

@ -166,7 +166,7 @@
} }
--- a/arch/arm/mach-ixp4xx/Kconfig --- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig +++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -89,6 +89,14 @@ @@ -107,6 +107,14 @@
WRT300N v2 router. For more information on this WRT300N v2 router. For more information on this
platform, see http://openwrt.org platform, see http://openwrt.org
@ -183,7 +183,7 @@
help help
--- a/arch/arm/mach-ixp4xx/Makefile --- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile +++ b/arch/arm/mach-ixp4xx/Makefile
@@ -20,6 +20,7 @@ @@ -21,6 +21,7 @@
obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o
obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o
obj-pci-$(CONFIG_MACH_SIDEWINDER) += sidewinder-pci.o obj-pci-$(CONFIG_MACH_SIDEWINDER) += sidewinder-pci.o
@ -191,7 +191,7 @@
obj-y += common.o obj-y += common.o
@@ -38,6 +39,7 @@ @@ -40,6 +41,7 @@
obj-$(CONFIG_MACH_COMPEX) += compex-setup.o obj-$(CONFIG_MACH_COMPEX) += compex-setup.o
obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o
obj-$(CONFIG_MACH_SIDEWINDER) += sidewinder-setup.o obj-$(CONFIG_MACH_SIDEWINDER) += sidewinder-setup.o

View File

@ -1,30 +0,0 @@
--- a/arch/arm/mach-ixp4xx/wg302v1-setup.c
+++ b/arch/arm/mach-ixp4xx/wg302v1-setup.c
@@ -77,9 +77,27 @@
.resource = &wg302v1_uart_resource,
};
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info wg302_plat_eth[] = {
+ {
+ .phy = 30,
+ .rxq = 3,
+ .txreadyq = 20,
+ }
+};
+
+static struct platform_device wg302_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = wg302_plat_eth,
+ }
+};
+
static struct platform_device *wg302v1_devices[] __initdata = {
&wg302v1_flash,
&wg302v1_uart,
+ &wg302_eth[0],
};
static void __init wg302v1_init(void)

View File

@ -1,7 +1,7 @@
--- a/arch/arm/mach-ixp4xx/wg302v1-setup.c --- a/arch/arm/mach-ixp4xx/wg302v1-setup.c
+++ b/arch/arm/mach-ixp4xx/wg302v1-setup.c +++ b/arch/arm/mach-ixp4xx/wg302v1-setup.c
@@ -100,6 +100,36 @@ @@ -99,6 +99,36 @@
&wg302_eth[0], &wg302v1_eth[0],
}; };
+static char wg302v1_mem_fixup[] __initdata = "mem=32M "; +static char wg302v1_mem_fixup[] __initdata = "mem=32M ";
@ -37,7 +37,7 @@
static void __init wg302v1_init(void) static void __init wg302v1_init(void)
{ {
ixp4xx_sys_init(); ixp4xx_sys_init();
@@ -118,6 +148,7 @@ @@ -117,6 +147,7 @@
/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
.phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
.io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,

View File

@ -1,6 +1,6 @@
--- a/arch/arm/mach-ixp4xx/Kconfig --- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig +++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -150,6 +150,14 @@ @@ -160,6 +160,14 @@
PrPCM1100 Processor Mezanine Module. For more information on PrPCM1100 Processor Mezanine Module. For more information on
this platform, see <file:Documentation/arm/IXP4xx>. this platform, see <file:Documentation/arm/IXP4xx>.
@ -276,8 +276,8 @@
*/ */
if (machine_is_adi_coyote() || machine_is_gtwx5715() || if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
machine_is_gateway7001() || machine_is_wg302v2() || machine_is_gateway7001() || machine_is_wg302v2() ||
- machine_is_pronghorn_metro() || machine_is_wrt300nv2()) - machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2())
+ machine_is_pronghorn_metro() || machine_is_wrt300nv2() || + machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2() ||
+ machine_is_tw5334()) + machine_is_tw5334())
uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS; uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
else else

View File

@ -15,7 +15,7 @@
config MACH_LOFT config MACH_LOFT
bool "Loft" bool "Loft"
depends on MACH_AVILA depends on MACH_AVILA
@@ -200,7 +208,7 @@ @@ -210,7 +218,7 @@
config CPU_IXP43X config CPU_IXP43X
bool bool

View File

@ -1,3 +1,15 @@
From cba5c286f3ea34ea4767fc00c705434a00fe2c37 Mon Sep 17 00:00:00 2001
From: Imre Kaloz <kaloz@openwrt.org>
Date: Thu, 26 Jun 2008 01:58:02 +0200
Subject: [PATCH] Add support for the ethernet ports on IXP43x
---
arch/arm/mach-ixp4xx/ixp4xx_npe.c | 6 +++---
drivers/net/arm/ixp4xx_eth.c | 13 +++++++++----
include/asm-arm/arch-ixp4xx/cpu.h | 2 ++
include/asm-arm/arch-ixp4xx/ixp4xx-regs.h | 7 ++++---
4 files changed, 18 insertions(+), 10 deletions(-)
--- a/arch/arm/mach-ixp4xx/ixp4xx_npe.c --- a/arch/arm/mach-ixp4xx/ixp4xx_npe.c
+++ b/arch/arm/mach-ixp4xx/ixp4xx_npe.c +++ b/arch/arm/mach-ixp4xx/ixp4xx_npe.c
@@ -575,8 +575,8 @@ @@ -575,8 +575,8 @@

View File

@ -13,7 +13,7 @@
--- a/arch/arm/mach-ixp4xx/Kconfig --- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig +++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -236,6 +236,11 @@ @@ -246,6 +246,11 @@
default y default y
depends on PCI depends on PCI