(6/6) bcm57xx: package

This is the bcm57xx package.  I have tested default vlan functions,
but I dont have the equipment to test more advanced setups.  The default
vlan setup seems to be working fine.  I also added the activate_gpio
parameter which will make the driver activate the switch via gpio before
probing for it.

I'm not sure which method is best for autoload.  For the wrt350n, I
need the activate_gpio parameter.  But its probably not a good idea
to add that to the autoload file.  On a system without a bcm57xx switch,
isn't it a bad idea to mess with the gpios looking for the switch? Ideally,
wouldn't it be best to load the bcm57xx module from broadcom-diag, after
it has determined which router its on?  I tried using 'request_module' from
there, but had no success.  For now, I am relying on preinit to load
the bcm57xx module with activate_gpio param, after it has failed to load
switch_robo and switch_adm.

Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu>


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11471 3c298f89-4303-0410-b956-a3cf2f4a3e73

package/broadcom-57xx/Makefile

@@ -0,0 +1,51 @@
+# 
+# Copyright (C) 2006 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+# $Id: Makefile 8694 2007-09-08 19:55:42Z nbd $
+
+include $(TOPDIR)/rules.mk
+include $(INCLUDE_DIR)/kernel.mk
+
+PKG_NAME:=broadcom-57xx
+PKG_RELEASE:=1
+
+include $(INCLUDE_DIR)/package.mk
+
+define KernelPackage/brcm-57xx
+  SUBMENU:=Network Devices
+  DEPENDS:=@TARGET_brcm_2_4 +kmod-switch
+  TITLE:=Broadcom 57xx ethernet support
+  FILES:=$(PKG_BUILD_DIR)/bcm57xx.$(LINUX_KMOD_SUFFIX)
+  AUTOLOAD:=$(call AutoLoad,30,bcm57xx)
+endef
+
+define Build/Prepare
+	mkdir -p $(PKG_BUILD_DIR)
+	$(CP) ./src/* $(PKG_BUILD_DIR)/
+endef
+
+ifeq ($(BOARD),brcm-2.4)
+	BUILDFLAGS = -DBCMDRIVER -I$(LINUX_DIR)/arch/mips/bcm947xx/include -I$(STAGING_DIR)/usr/include
+	BUILDFLAGS += -DDBG=0 -DBCM_PROC_FS=1 -DT3_JUMBO_RCV_RCB_ENTRY_COUNT=256 -DNICE_SUPPORT
+	BUILDFLAGS += -DPCIX_TARGET_WORKAROUND=1 -DINCLUDE_TBI_SUPPORT=1 -DINCLUDE_5701_AX_FIX=1
+endif
+
+define Build/Compile
+	$(MAKE) -C "$(LINUX_DIR)" \
+		CROSS_COMPILE="$(TARGET_CROSS)" \
+		ARCH="$(LINUX_KARCH)" \
+		SUBDIRS="$(PKG_BUILD_DIR)" \
+		EXTRA_CFLAGS="$(BUILDFLAGS)" \
+		modules
+endef
+
+define KernelPackage/brcm-57xx/install
+	$(call Package/brcm-57xx/install/Default,$(1))
+	#$(INSTALL_DIR) $(1)/etc/modules.d
+	#echo "bcm57xx activate_gpio=1" > $(1)/etc/modules.d/30-bcm57xx
+endef
+
+$(eval $(call KernelPackage,brcm-57xx))