- Fixes the use of CONFIG_UCI_PRECONFIG under git; git does not track empty directories.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11517 3c298f89-4303-0410-b956-a3cf2f4a3e73
to get and set bootloader options in flash memory.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11514 3c298f89-4303-0410-b956-a3cf2f4a3e73
to get and set bootloader options in flash memory.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11512 3c298f89-4303-0410-b956-a3cf2f4a3e73
r6040_rx() was rewritten.
Further changes:
- fix a bug in hex2str(), which overwrote the source with a zero
- removed rx_free_desc counter; allocate skb inside r6040_rx() on the fly
- r6040_rx: don't take the error from the MLSR register (may be too late) but from the descriptor (we may have to allow these errors (via MCR0) there
- r6040_alloc_rxbufs() may fail due to lack of skb, added a return value
- changed some debugs
- more defines
- version: 0.18 -> 0.19
Signed-Off by Joerg Albert <jal2@gmx.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11508 3c298f89-4303-0410-b956-a3cf2f4a3e73
- re-added the parent parameter to specify a netdevice to steal the MAC address from (optional).
- fixed null pointer access in r6040_rx() (lp->dev init. was missing)
- fixed "scheduling while atomic" endless loop if tx_timeout() was called (caused by the re-allocs of the buffers)
- fixed tx timeouts (tx irq weren't re-enabled on rx irq)
It adds some defines and cleans the code a bit (IMHO).
Signed-Off by Joerg Albert <jal2@gmx.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11507 3c298f89-4303-0410-b956-a3cf2f4a3e73
this is the first of three patches to fix the ethernet driver of RDC R32xx applied to svn r10754.
It adds debugs and make some procedures (r6040_*) global symbols in order to help with debugging kernel oops. Version is increased from 0.16 to 0.18 to avoid conflicts with the driver variant metioned in the X-WRT forum (call 0.17.3) Tested on a Sitecom WL-153.
Signed-Off-By: Joerg Albert <jal2@gmx.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11506 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is the bcm57xx package. I have tested default vlan functions,
but I dont have the equipment to test more advanced setups. The default
vlan setup seems to be working fine. I also added the activate_gpio
parameter which will make the driver activate the switch via gpio before
probing for it.
I'm not sure which method is best for autoload. For the wrt350n, I
need the activate_gpio parameter. But its probably not a good idea
to add that to the autoload file. On a system without a bcm57xx switch,
isn't it a bad idea to mess with the gpios looking for the switch? Ideally,
wouldn't it be best to load the bcm57xx module from broadcom-diag, after
it has determined which router its on? I tried using 'request_module' from
there, but had no success. For now, I am relying on preinit to load
the bcm57xx module with activate_gpio param, after it has failed to load
switch_robo and switch_adm.
Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11471 3c298f89-4303-0410-b956-a3cf2f4a3e73
I noticed my wrt350n would not reliably reboot after entering
the reboot command. I found this code in the source for the
wrt600n. It corrects the problem, and the wrt350n reboots
reliably now.
Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11470 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch prevents switch-robo.c from attempting robo_probe on a port
that is already registered. robo_probe will adjust kernel reference counts
if it detects a switch on the port. If this patch wasn't applied, the
wrt350n would hang on reboot, waiting for the network driver reference count
to reach zero indefinitely.
Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11469 3c298f89-4303-0410-b956-a3cf2f4a3e73
