Use offset from struct mtd_part instead of struct mtd_partition for defining
the new partitions. This enables the usage of MTDPART_OFS_APPEND macro in
struct mtd_partition.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26705 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes a bug that led to ECN enabled flows being de-prioritized by pfifo_fast
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26687 3c298f89-4303-0410-b956-a3cf2f4a3e73
Dual image capable CFEs store an image sequence at the same place as
currently OpenWrt stores the actual rootfs length, so it will get
overwritten when flashing through such a CFE.
To prevent this from happening, move the rootfs length field to the next
four bytes, thus completely using the reserved1 field.
Since the reserved1 field is now completely in use, it does not make sense
to allow it to be set from the imagetag utility, so remove the option.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26680 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add the PC speaker back to the Geos platform.
Add DMI support in BIOS.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26678 3c298f89-4303-0410-b956-a3cf2f4a3e73
These patches were submitted to netdev and will likely be out in 2.6.38.3.
In the meantime, they're needed in 2.6.37.6.
Patch by Philip Prindeville
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26616 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for 2.6.39 based on rc3. Runtime tested on bcm63xx.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26615 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for the Buffalo WZR-HP-G301NH. The only difference between it
and the WZR-HP-G00NH is that it has a RTL8366RB instead of a RTL8366S.
Since we don't do runtime detection of the switch, we need a separate
machine definition for it.
While we are at it, also rename the profile to reflect that it now is for
more than one device.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26601 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since the PHY driver is only used for the WAN port and there is virtually
no difference between it and the generic PHY driver, we can sefely remove
it.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26600 3c298f89-4303-0410-b956-a3cf2f4a3e73
This was just a little bit tested on an SAMSUNG SMT-G3020 and pci and usb do not work like before.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26576 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Some module should be loaded later to load them after the modules they are depending on
* add some more missing config symbols
* make CS5535 build again
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26570 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also initialize that for each SoC and print its value along with the
other frequencies.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26561 3c298f89-4303-0410-b956-a3cf2f4a3e73
