Create the default network configuration dynamically for the boards with
swapped eth0, eth1 interfaces.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28819 3c298f89-4303-0410-b956-a3cf2f4a3e73
Create the default network configuration dynamically for the boards with
a single ethernet interface.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28818 3c298f89-4303-0410-b956-a3cf2f4a3e73
U-Boot on the ALL0258N needs offset, size and md5 for kernel and rootfs to be
stored in the U-Boot environment.
If the checksums don't match during boot, a failsafe-system is booted instead.
This patch adds a board-specific sysupgrade hack for the all0258n which
calculates and updates the checksums for the U-Boot environment.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28700 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds default network and uboot-env settings for the ALL0258N.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28699 3c298f89-4303-0410-b956-a3cf2f4a3e73
Aparently $magic_long was meant here instead of $magic when comparing with
32-bit values.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28678 3c298f89-4303-0410-b956-a3cf2f4a3e73
The initial support for the Buffalo WHR-HP-G300N box.
The code was confirmed to boot and run, but not tested in depth.
Known problem: iw phy phy0 info shows:
Coverage class: 0 (up to 0m)
Available Antennas: TX 0 RX 0
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28567 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patchs adds support for the Allnet ALL0258N outdoor AP/bridge.
The ALL0258N is based on the AR7240 SoC paired with an AR9285 radio,
it got 8MB of NOR and 32MB SDRAM.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28564 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now that we can use a generic name for the switch there is no need for a
separate image for the WZR-HP-G301NH.
Update the default network config and remove the extra image.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27814 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for the Buffalo WZR-HP-G301NH. The only difference between it
and the WZR-HP-G00NH is that it has a RTL8366RB instead of a RTL8366S.
Since we don't do runtime detection of the switch, we need a separate
machine definition for it.
While we are at it, also rename the profile to reflect that it now is for
more than one device.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26601 3c298f89-4303-0410-b956-a3cf2f4a3e73
Enables forwarding of frames between the switch ports (eth0).
Patch by Jouni Malinen
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26180 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Dave Lichterman <laviddichterman@gmail.com>
[nand-disk trigger has been removed - juhosg]
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24642 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds image generation for NBG460N/550N/550NH boards.
Signed-off-by: Michael Kurz <michi.kurz@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24419 3c298f89-4303-0410-b956-a3cf2f4a3e73
For WNDR3700, use green for 1Gb/s and amber for 100Mb/s and 10Mb/s on
the four LAN port switch LEDs. The LEDs will be lit to indicate a link
and will blink to indicate activity. This matches the stock firmware
and the description printed on the label on the unit's underside.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23879 3c298f89-4303-0410-b956-a3cf2f4a3e73
Make the WiFi LEDs blink for activity on the WNDR3700, matching the
stock firmware and user expectations. The green 2.4GHz and blue 5GHz
LEDs will illuminate with the radio on, and will blink to indicate
transmission and reception.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23877 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch-by: Cezary Jackiewicz <cezary@eko.one.pl>
(the GPIODEV code has been removed, the sysfs interface
can be used to control the GPIO lines instead - juhosg)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23165 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is still preliminary and not really tested much. Anyway, this
version seems to be enough to get both wired and wireless
interfaces working. Buttons and leds are also working.
mach-ap96.c is based on mach-wndr3700.c.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23125 3c298f89-4303-0410-b956-a3cf2f4a3e73
hooks directly into the ethernet driver, as MAC resets also require switch reinitializations and the switch is part of the cpu core anyway
switch only tl-wr741nd (and other devices using this board file, such as tl-wr841nd) over to using this by default, as other devices are still untested
fixes#7563
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22675 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the Senao EAP7660D board to diag.sh and sysupgrade.
Signed-off-by: Daniel Golle <daniel.golle@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22644 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the Senao EAP7660D board to trunk.
Signed-off-by: Daniel Golle <daniel.golle@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21837 3c298f89-4303-0410-b956-a3cf2f4a3e73
wget2nand didnt check the exit status after copying the kernel, if the
copying failed for some reason ( for example not enougs space on the
kernel partition) it simply continued extracting the rootfs.
I also changed the filename, which wget2nand trys to download (
.tar.gz instead of .tgz ).
Signed-off-by: Marko Foerster <mrkfoerster@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21444 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch enhances the ar8216 driver with ar8316 support and fixes some minor
issues with the ar8216 driver itself. It should not break anything, but isn't
tested on ar8216 devices.
[PATCH 2/2] ar71xx: Add the ar8316 driver to rs pro/rb-450g.
Add the ar8216 driver to the ar71xx target, and add network
configurations for the RouterStation Pro and the RouterBoard RB-450G.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@20722 3c298f89-4303-0410-b956-a3cf2f4a3e73
