Allow enabling of N-PHY support for BCM4321 and BCM4322.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26736 3c298f89-4303-0410-b956-a3cf2f4a3e73
Allow reenabling the PIO mode fallback for b43.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26735 3c298f89-4303-0410-b956-a3cf2f4a3e73
Allow enabling debug output and debugfs for B43.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26734 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add the 5.10.56.27 firmware option. This includes updating b43-fwcutter to
its newest release 14 and updating the b43-fwsquash.py to recognise rev 16
n phy files.
Also rename the current options from STABLE/EXPERIMENTAL to their version
numbers.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26733 3c298f89-4303-0410-b956-a3cf2f4a3e73
Currently the device id in the platform driver is hardcoded to an
id which is specific to AR9130/AR9132 SOCs as it supports only wmac
(wireless mac) of these SOCs. But this needs to be dynamic when we
want to support different wmac of SOCs. So add id_table to driver to
make it extendable to more SOCs.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26604 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Some module should be loaded later to load them after the modules they are depending on
* add some more missing config symbols
* make CS5535 build again
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26570 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds the Intel wireless drivers for their normal cards.
Thank you framer99 for the patch, I extended it a little bit.
This closes#7227
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26534 3c298f89-4303-0410-b956-a3cf2f4a3e73
adds some more pending patches which (among other things) fix the 'failed to stop RX DMA' messages
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26506 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds WLAN LED support to the mac80211 driver for Ralink
rt2x00/rt2800 (rt305x) SoC devices. The current driver in
kmod-rt2800-lib is based upon PCI, not SoC. The WLAN LED drivers in
rt2800lib.c set the LED brightness via an MCU request, but do nothing
for SoC. This patch checks for SoC and sets the register to enable the
WLAN LED (instead of an MCU request). This fixes the WLAN LED for
RT305x devices (such as the HW550-3G).
Signed-off-by: Layne Edwards <ledwards76@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26463 3c298f89-4303-0410-b956-a3cf2f4a3e73
CONFIG_RT2800PCI_PCI and CONFIG_RT2800PCI_SOC were removed some time ago and CONFIG_IWLWIFI was replaced by CONFIG_COMPAT_IWLWIFI in compat wireless
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24794 3c298f89-4303-0410-b956-a3cf2f4a3e73
