This patch adds support for defining rt2x00 eeprom data.
This eeprom data can be extracted from flash or loaded directly from a firmware file.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34322 3c298f89-4303-0410-b956-a3cf2f4a3e73
SPW303V also needs its CRC fixed up since increasing the image size to
4MB to prevent the dual image mode of CFE.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34091 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Miguel GAIO <miguel.gaio@efixo.com>
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
[jonas.gorski@gmail.com: add network config for nb6, make switch fix a
platform patch]
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32924 3c298f89-4303-0410-b956-a3cf2f4a3e73
Build images for 96328avng and 963281TAN (untested) for three different
flash sizes: 4MB, 8MB, and 16MB.
Known issues:
* Button setup unknown, thus no fail-safe available.
* All other BCM6328 and BCM63XX issues
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32004 3c298f89-4303-0410-b956-a3cf2f4a3e73
No need to keep the bcm63xx/ at the start or the chipid info at the end.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31871 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for D-Link's DVA-G3810BN/TL product.
Signed-off-by: Roman Dumycz <roman@secureas.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26956 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add the required board definition, default config and image generation for
the T-Home Speedport W 303V Typ B.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26878 3c298f89-4303-0410-b956-a3cf2f4a3e73
Rename the DSL-274xB rev C2's board ID to "AW4139" to match the one used
for the rev C3 (same hardware) and add a fixup for C2. Also generate
images for C3.
While we are at it, rename the LEDs to conform to the Linux LED naming
conventions.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26876 3c298f89-4303-0410-b956-a3cf2f4a3e73
I wrote a patch to add 96348SV board (aka MAGIC) support to trunk.
In my case I've found it in a Telsey "Alice W-Gate" router, fairly common
(in the past) in Italy.
I used the board definition (GPIOs, leds, ...) from the Broadcom GPL-2
relased code (here is a mirror: http://beghiero.myftp.org/sorgenti/boardparms.c )
Thanks to KanjiMonster for the support on the IRC channel.
Signed-off-by: Laurento Frittella <laurento.frittella@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@25584 3c298f89-4303-0410-b956-a3cf2f4a3e73
The device is called SPW500V, not SP500W.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@25431 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for the T-Com Speedport W 500V using a special tagged image as it
identifies itself as a 96348GW, but has some gpios wired differently, and also
has only one ethernet port without a switch attached to it.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24190 3c298f89-4303-0410-b956-a3cf2f4a3e73
The DSL-2740B/DSL-2741B rev C2 support was missing the board definition,
resulting in a kernel panic on boot.
This patch adds it, and also renames the generated image name to properly
reflect that it is for the revision C2, and for both the DSL-2740B and
DSL-2741B.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24188 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since some devices have more than one power led, they might be separated by
their color in the name. To also allow them to be on after leaving preinit,
set any status led starting with 'power' to on instead of only those with
the exact name of 'power'.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24187 3c298f89-4303-0410-b956-a3cf2f4a3e73
Port the mechanism for different default configurations from ar71xx and
use the old configuration as the default configuration. This should have
no functional differences to before.
While we are at it, remove the obsolete nat option.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24185 3c298f89-4303-0410-b956-a3cf2f4a3e73
