This adds support for the Netgear WNDR3800, it is almost the same as
the WNDR3700v2. It just has more RAM so the hd_id had to be adjusted.
Signed-off-by: Petri Rosenström <petri.rosenstrom@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28597 3c298f89-4303-0410-b956-a3cf2f4a3e73
The preconfiguration of the USB LED has benn move to the
/etc/uci-defaults/leds script. [juhosg]
Signed-off-by: Adam Porter <porter.adam at gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28571 3c298f89-4303-0410-b956-a3cf2f4a3e73
WAN is on swtich port 0 for Aztech HW550-3G.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28570 3c298f89-4303-0410-b956-a3cf2f4a3e73
This removes unnecessary duplication and simplifies led setup for new
boards. It would be a one line change most likely.
Signed-off-by: Alexander Gordeev <lasaine@lvk.cs.msu.su>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28569 3c298f89-4303-0410-b956-a3cf2f4a3e73
The initial support for the Buffalo WHR-HP-G300N box.
The code was confirmed to boot and run, but not tested in depth.
Known problem: iw phy phy0 info shows:
Coverage class: 0 (up to 0m)
Available Antennas: TX 0 RX 0
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28567 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patchs adds support for the Allnet ALL0258N outdoor AP/bridge.
The ALL0258N is based on the AR7240 SoC paired with an AR9285 radio,
it got 8MB of NOR and 32MB SDRAM.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28564 3c298f89-4303-0410-b956-a3cf2f4a3e73
AR8316 behind a GPIO bitbanged MDIO bus fails to drive the turnaround bit
to low despite returning a valid value. Ignore it and just use the
returned value anyway.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28422 3c298f89-4303-0410-b956-a3cf2f4a3e73
A fast stop/start cycle could leave the ag71xx interrupts and tx engine
disabled when using a phy driver with a fixed link and the start/stop
happens between two phy state machine polls.
Prevent this by always forcing the link down on stop regardless of phy
state and having a phy connected.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28380 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix typo from previous submission with input-keys-polled.
Philip Prindeville - 2011-10-03 01:44:55
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28356 3c298f89-4303-0410-b956-a3cf2f4a3e73
---
Attaching the correct file this time...
Philip Prindeville - 2011-09-07 07:01:42
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28355 3c298f89-4303-0410-b956-a3cf2f4a3e73
Don't make the config more complicated than it needs to be.
Philip Prindeville - 2011-08-29 03:15:27
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28353 3c298f89-4303-0410-b956-a3cf2f4a3e73
Hi,
this patch adds the correct vlan definitions for the Siemens SE505v2. It
applies to trunk as well as backfire (please apply here too). On
backfire this also patches brcm-2,4, because brcm47xx base-files is just
symlinked to brcm-2.4.
It also fixes two whitespace issues.
Tested with brcm47xx on both trunk and backfire branch and works as
expected.
Signed-off-by: Manuel Munz <freifunk@somakoma.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28336 3c298f89-4303-0410-b956-a3cf2f4a3e73
The enable function was using the global timeout variable for local operations.
This resulted in the value of the global variable being corrupted, thus
breaking the code.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28310 3c298f89-4303-0410-b956-a3cf2f4a3e73
* rebase 3.0 patches
* fold some fixes into existing patches
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28308 3c298f89-4303-0410-b956-a3cf2f4a3e73
Same hardware as WR741ND but with PoE support.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28271 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds the option to enable jumbo frames on the rtl8366s
switch. This is almost exactly the same as the first patch at
https://dev.openwrt.org/ticket/7977 and it has been requested
in a comment there.
I have tested this and it successfully allows devices on the switch
using jumbo frames to communicate.
Signed-off-by: Ash Hughes <ashley.hughes@blueyonder.co.uk>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28267 3c298f89-4303-0410-b956-a3cf2f4a3e73
- don't regenerate Package index unless the packagedir changes
- remove opkg lists from rootfs, saves > 1MB uncompressed
- don't direct errors on index creation into packagelist
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28205 3c298f89-4303-0410-b956-a3cf2f4a3e73
