[juhosg: export xt_layer7.h for all kernel versions]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31566 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixed: GPIO typos and confirmed GPIO_BUTTON_RESET
Fixed: Lan & Wan reversed: swaped "eth0.2" with "eth0.1" by
removing a line(default is correct), and reversed the
Lan/wan layout LLLLW to WLLLL.
Added: image/Makefile now builds -factory.bin files. I am
unsure of the accepted way to change the makefile but
the name of the image needs to be 'linkn Kernel Image'
in order to be accepted by the OEM firmware.
Known issue: eth0 (internal switch i think has mac address:
00:11:22:33:44:55 but i think it should be same as
the lan).
Known issue: Pressing the reset button has no noticable effect,
i would expect the router to boot failsafe if being
pressed on boot, reboot if short press and reset all
to default if long press.
[juhosg: remove mtdlayout_W306R and use mtdlayout_4M instead]
Signed-off-by: David Pearce <david_18051985@hotmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31557 3c298f89-4303-0410-b956-a3cf2f4a3e73
Make serial console for DIR-300-B1 work again.
With some recent change, "console=ttyS1,57600" was removed from the
default kernel command line, this adds the necessary mkcmdline
incantation to image/Makefile to add it there for this target.
This is quite likely broken for other targets as well.
Without this the console switches to ttyS0 instead of ttyS1 and
kernel output is missing, and the userspace comes up with 9600 baud
instead of 57600.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31556 3c298f89-4303-0410-b956-a3cf2f4a3e73
Based on a patch by Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31529 3c298f89-4303-0410-b956-a3cf2f4a3e73
Based on a patch by Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31523 3c298f89-4303-0410-b956-a3cf2f4a3e73
V=99 and V=1 are now deprecated in favor of a new verbosity class system,
though the old flags are still supported.
You can set the V variable on the command line (or OPENWRT_VERBOSE in the
environment) to one or more of the following characters:
- s: stdout+stderr (equal to the old V=99)
- c: commands (for build systems that suppress commands by default, e.g. kbuild)
- w: warnings/errors only (equal to the old V=1)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31484 3c298f89-4303-0410-b956-a3cf2f4a3e73
The existing code (prior to the patch) does an "ioremap_nocache" on a
subset of a memory region that I think has already been mapped, and then
un-maps that smaller region when it is finished.
Thanks Nathan Hintz for the patch
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31481 3c298f89-4303-0410-b956-a3cf2f4a3e73
Partially based on the 3.1 patches by Hartmut Knaack <knaack.h [at] gmx.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31474 3c298f89-4303-0410-b956-a3cf2f4a3e73
