The VLAN mapping on the ARV4520PW board is the following:
port on Router: | VLAN in software:
LAN 1 | 3
LAN 2 | 2
LAN 3 | 1
LAN 4 | 0
DSL | 4
So LAN4 is not VLAN4 but VLAN0 (VLAN4 is DSL port) -> set "3 2 1 0 5t" as default switch config.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31391 3c298f89-4303-0410-b956-a3cf2f4a3e73
Implements the ARV752DPW architecture in mach-arv.c
Signed-off-by: Christian Rustmeier <rustmeier@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31206 3c298f89-4303-0410-b956-a3cf2f4a3e73
A power-enable toggle gpio is not available, it is always on and protected with a resettable fuse.
Signed-off-by: Pieter Voorthuijsen<p.voorthuijsen at gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31205 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also remove a duplicate patch from lantiq (already in generic).
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31158 3c298f89-4303-0410-b956-a3cf2f4a3e73
Turns out it triggers on some AR71xx devices where no swapping should be done.
Enable endian check for the lantiq target.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31084 3c298f89-4303-0410-b956-a3cf2f4a3e73
Needed for using external rootfs on usb sticks.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30940 3c298f89-4303-0410-b956-a3cf2f4a3e73
With this patch it is possible to generate uboot environment config file
inside lantiq target. Currently it is only supporting GIGASX76X board.
uboot environment config is used by fw_printenv fw_setenv tools.
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30537 3c298f89-4303-0410-b956-a3cf2f4a3e73
While the disadvantage is less available flash space, it's easy and
safe to flash without opening the device.
Going back to the original firmware is also possible.
This patch add two firmware utilities, mkbrncmdline and mkbrnboot.
mkbrncmdline patches the uncompressed kernel so the registeres a0 to
a3 are initialized and the memory size is passed in.
mkbrnboot takes the lzma compressed kernel and squashfs images and
creates a firmware image that can be flashed using the BRN-BOOT
recovery kernel, which is booted by holding both buttons when
powering up the device and will listen on http://192.168.2.1.
The firmware file from bin/lantiq/ to use is
openwrt-lantiq-danube-ARV4525PW-BRNDTW502-brnImage
The BRN-BOOT recovery kernel does size-check the image, so if it's
too big to fit into flash it will complain accordingly.
A second patch is needed to make the wired network interface work
since there is no u-boot to pre-initialise it.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30532 3c298f89-4303-0410-b956-a3cf2f4a3e73
* fixes leds
* adds all leds found on the sx763 board
* removes board_config from flash layout because wireless data is stored in kernel (ath5k)
* fix button handling
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29763 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch is/was a duplicate of generic/patches-3.1/307-mips_oprofile_fix.patch
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29294 3c298f89-4303-0410-b956-a3cf2f4a3e73
The enable function was using the global timeout variable for local operations.
This resulted in the value of the global variable being corrupted, thus
breaking the code.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28310 3c298f89-4303-0410-b956-a3cf2f4a3e73
