BCM6338 and BCM6338 have their MSG_CONTROL register width of 8-bits instead of
16-bits. We were previously using a 16-bits write which corrupted the first
byte of the TX FIFO. Also the message type was always set to Full-duplex even
in the case of half-duplex messages.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32409 3c298f89-4303-0410-b956-a3cf2f4a3e73
Merge most fixes from #8677:
- add basic hardware detection of Livebox Blue 5g revisions
- register leds and gpio buttons
- fix boot address location
- properly parse mac addresses
Plus some more fixes:
- make board_livebox.c more in line with board_bcm963xx.c
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32087 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some new board definitions were added within the #ifdef CONFIG_CPU_6338
section while some other were added within #ifdef CONFIG_CPU_6345, fix this
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32060 3c298f89-4303-0410-b956-a3cf2f4a3e73
It uses spi_register_board_info() from linux/spi/spi.h but does not include it
explicitely.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32058 3c298f89-4303-0410-b956-a3cf2f4a3e73
Build images for 96328avng and 963281TAN (untested) for three different
flash sizes: 4MB, 8MB, and 16MB.
Known issues:
* Button setup unknown, thus no fail-safe available.
* All other BCM6328 and BCM63XX issues
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32004 3c298f89-4303-0410-b956-a3cf2f4a3e73
Build images for D-Link DSL-274XB revision F1. Flashing
through original web UI as well as CFE works.
Known issues:
* wifi led inverted (on when wifi is off and vice cersa)
* same issues as generic bcm6328 support
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31885 3c298f89-4303-0410-b956-a3cf2f4a3e73
BCM6328 support is in a usable state, with the following issues
* internal switch port not configurable
* external phys not supported
* broadcom wifis will probably not work correctly
* and all other generic bcm63xx issues (so yes, still no ADSL)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31883 3c298f89-4303-0410-b956-a3cf2f4a3e73
bcm_enetsw_probe did not properly reset port states, resulting in
connected ports staying disabled after bringing up the interface the
second time.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31881 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for the HSSPI controller found on bcm6328 and SPI attached
flash.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31879 3c298f89-4303-0410-b956-a3cf2f4a3e73
Prevents CFE from flashing to the second image offset. Fix up the rootfs
length on first boot else CFE will complain.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31876 3c298f89-4303-0410-b956-a3cf2f4a3e73
No need to keep the bcm63xx/ at the start or the chipid info at the end.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31871 3c298f89-4303-0410-b956-a3cf2f4a3e73
The fallback sprom handler was installed too late, resulting in ssb
failing to get a valid sprom on some devices.
Fixes#11384.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31638 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add basic support for the internal ethernet switch on bcm6368. It behaves
as a dumb switch for now, but allows basic connectivity.
Also drop the ethernet patch for bcm6345 for now, it needs rework.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31129 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add missing external IRQ code parts for older chips in the new code.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31128 3c298f89-4303-0410-b956-a3cf2f4a3e73
Reorder patches for a clearer distinction between the purposes of
the different patches.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31127 3c298f89-4303-0410-b956-a3cf2f4a3e73
