This allows them to transparently communicate with an external VLAN switch.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33305 3c298f89-4303-0410-b956-a3cf2f4a3e73
Power down phy on disabled switch ports.
Haven't measured this myself yet, but according to this
http://www.8devices.com/community/viewtopic.php?f=6&t=156
it can save about 300mW of power.
[juhosg: fix checkpatch warning]
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33304 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for 8devices Carambola dev board.
The Carambola is a small RT3050-based development board with two
ethernet ports, on-board chip antenna, usb and plenty of accessible
gpio ports, sold by 8devices.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33303 3c298f89-4303-0410-b956-a3cf2f4a3e73
Rename POC registers.
The current code uses POC1-POC3.
The datasheet uses:
POC1: Port Control 0
POC1: Port Control 1
POC2: Port Control 2
So the first POC1 is a typo that should have been POC0, rename the
registers to POC0-POC2 accordingly.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33302 3c298f89-4303-0410-b956-a3cf2f4a3e73
Stop handling VLAN setup in the kernel.
Removes the obsolete RT305X_ESW_VLAN_CONFIG_BYPASS option I added for
WL-351 and add some extra comments.
Also removes the en_vlan per-port flag that isn't very useful really, it now
is only controlled by the global enable_vlan flag.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33301 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add switch setup to uci network defaults.
The 'lan' attribute is used to decide into which vlan to put the
port.
Currently 'disable' is never set, but the intention is to use this
for devices like the 8devices Carambola, which only has two ports
hooked up to the SoC.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33300 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add swconfig support to ramips_esw.c
This patch adds swconfig support for ramips_esw:
Tested on both D-LINK DIR-300 B1 and Sitecom WL-351 (external
rtl8366rb on internal port 5).
I've made sure that in the enable_vlan=0 case it behaves like a dumb
switch, so external switches should work fine with vlans and
verified this on the WL-351.
The current state shown by swconfig is always read directly from HW
registers, new settings only show after 'swconfig dev rt305x set apply'.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33299 3c298f89-4303-0410-b956-a3cf2f4a3e73
Minor indentation cleanup.
Prepare for the main swconfig patch by cleaning up indentation a bit.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33298 3c298f89-4303-0410-b956-a3cf2f4a3e73
An improved LED support for Buffalo WZR-HP-AG300H.
There will be two new packages to go with this patch
(ar922x-led-fix-hotplug and ar922x-led-fix-init).
These packages essentially perform the same task of
disabling "JTAG over GPIO pins" function which is
currently required for LEDs on AR922x emac GPIO to work,
and are both considered a temporary fix that circumvent
this problem.
[juhosg: add the hotplug script from the proposed
ar922x-led-fix-hotplug package to ar71xx/base-files]
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33294 3c298f89-4303-0410-b956-a3cf2f4a3e73
Commit 4878806326 (r33251) introduced a
regression with board= kernel command line parameter incorrectly
initialised.
The faulty builds propogated to the snapshots download area. This makes
the device unbootable and TP-Link users have to attach the serial to
recover.
Here is the q&d way i used to identify MIPS boards that didn't have a
corresponding entry in the image/Makefile:
for i in `find ../files/arch/mips/ath79/ -type f -exec cat {} \; \
| sed -n '/MIPS_MACHINE/ { s/^[^"]*"\([^"]*\)".*$/\1/; p; }'`; do
grep -q ,$i, Makefile || echo $i;
done > missing-boards.new
Reported-by: Casper on IRC
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33274 3c298f89-4303-0410-b956-a3cf2f4a3e73
OpenWRT runs in a eSATA sheevaplug like a charm. This patch just enables
CONFIG_MACH_ESATA_SHEEVAPLUG so the proper MACHINE_START definition
is compiled in.
Signed-off-by: Unai Uribarri <unaiur@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33266 3c298f89-4303-0410-b956-a3cf2f4a3e73
