- Fixes the use of CONFIG_UCI_PRECONFIG under git; git does not track empty directories.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11517 3c298f89-4303-0410-b956-a3cf2f4a3e73
to get and set bootloader options in flash memory.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11512 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is the bcm57xx package. I have tested default vlan functions,
but I dont have the equipment to test more advanced setups. The default
vlan setup seems to be working fine. I also added the activate_gpio
parameter which will make the driver activate the switch via gpio before
probing for it.
I'm not sure which method is best for autoload. For the wrt350n, I
need the activate_gpio parameter. But its probably not a good idea
to add that to the autoload file. On a system without a bcm57xx switch,
isn't it a bad idea to mess with the gpios looking for the switch? Ideally,
wouldn't it be best to load the bcm57xx module from broadcom-diag, after
it has determined which router its on? I tried using 'request_module' from
there, but had no success. For now, I am relying on preinit to load
the bcm57xx module with activate_gpio param, after it has failed to load
switch_robo and switch_adm.
Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11471 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch prevents switch-robo.c from attempting robo_probe on a port
that is already registered. robo_probe will adjust kernel reference counts
if it detects a switch on the port. If this patch wasn't applied, the
wrt350n would hang on reboot, waiting for the network driver reference count
to reach zero indefinitely.
Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11469 3c298f89-4303-0410-b956-a3cf2f4a3e73
I've been working to finish up the bcm57xx module package nbd
posted a few months ago. I am no expert, just had some spare
time and some motivation. Here is the background:
https://dev.openwrt.org/ticket/2744
This first patch disables the bcm57xx gpio setup in broadcom-diag.
The switch needs to be initialized by the driver so the driver can
then reset the switch ASAP. If the switch isn't reset quickly enough,
it will forward packets between the WAN and LAN, which will cause
problems with modems that only allow one mac to access the internet.
Tested on wrt350n.
Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11466 3c298f89-4303-0410-b956-a3cf2f4a3e73
improves uci.foreach and uci.get_all in the lua binding
no longer records changes for uci set with oldval == newval
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11354 3c298f89-4303-0410-b956-a3cf2f4a3e73
fixes LED on wisoc
fixes rx sensitivity issues
improves throughput on all cards/devices
enhances link stability
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11314 3c298f89-4303-0410-b956-a3cf2f4a3e73
