To make the ioctl number "stable", use an arbitrary high number to prevent
conflicts with new mtd ioctls that would push MTDREFRESH's number.
Also make mtd use the in-kernel mtd headers.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28893 3c298f89-4303-0410-b956-a3cf2f4a3e73
on some platforms, erase suspend leads to data corruption and lockups when write
ops collide with erase ops. this has been observed on the buffalo wzr-hp-g300nh.
rather than play whack-a-mole with a hard to reproduce issue on a variety of devices,
simply disable erase suspend, as it will usually not produce any useful gain on
the small filesystems used on embedded hardware.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27984 3c298f89-4303-0410-b956-a3cf2f4a3e73
KanjiMonster did the right patch, I was just confused because of linux-3.0 and linux-2.6.30
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27954 3c298f89-4303-0410-b956-a3cf2f4a3e73
find_task_by_vpid is already exported by the kernel without any patches needed.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27953 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is breaking some devices out there such as Winchiphead CH341 adapters (#9601)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27885 3c298f89-4303-0410-b956-a3cf2f4a3e73
Issue map read after Write Buffer Load command to ensure chip is ready
to receive data.
Signed-off-by: George Kashperko <george@znau.edu.ua>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27760 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes problem with TFM allocation in cryptosoft.c
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Hauke:
* remove ubsec_ssb package and take it from ocf-linux
* use patches from ocf-linux package
* refresh all patches
* readd some build fixes for OpenWrt.
* readd CRYPTO_MANAGER dependency
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27753 3c298f89-4303-0410-b956-a3cf2f4a3e73
* add new patches for bcm4716 SoC
* add support for serial flash on bcma bus
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27723 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since 2.6.38 the bridge module has a dependency to IPv6 if IPv6 is
enabled. Since the IPv6 module isn't exactly lightweight and bridge also
only needs a single function from IPv6, it's rather easy to create a
common "lib" module with a RCU pointer to the actual implementation, if
the IPv6 module is loaded (although slightly hackish).
The codepath seems to be only taken when using IPv6, so there should be
no negative side effects when IPv6 isn't loaded. I did not measure how
big the performance impact is.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27237 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also make linux identify itself properly as 3.0, not 3.0.0.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27191 3c298f89-4303-0410-b956-a3cf2f4a3e73
