diff -ru linux-2.6/arch/mips/boot/Makefile /plain/src/qi/linux-2.6.27.git.svn/arch/mips/boot/Makefile
--- linux-2.6/arch/mips/boot/Makefile	2009-08-18 00:01:01.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/arch/mips/boot/Makefile	2009-08-12 10:39:09.000000000 +0200
@@ -7,6 +7,9 @@
 # Copyright (C) 2004  Maciej W. Rozycki
 #
 
+# This one must match the LOADADDR in arch/mips/Makefile!
+LOADADDR=0x80010000
+
 #
 # Some DECstations need all possible sections of an ECOFF executable
 #
@@ -25,7 +28,7 @@
 
 VMLINUX = vmlinux
 
-all: vmlinux.ecoff vmlinux.srec addinitrd
+all: vmlinux.ecoff vmlinux.srec addinitrd uImage zImage
 
 vmlinux.ecoff: $(obj)/elf2ecoff $(VMLINUX)
 	$(obj)/elf2ecoff $(VMLINUX) vmlinux.ecoff $(E2EFLAGS)
@@ -42,8 +45,24 @@
 $(obj)/addinitrd: $(obj)/addinitrd.c
 	$(HOSTCC) -o $@ $^
 
+uImage: $(VMLINUX) vmlinux.bin
+	rm -f $(obj)/vmlinux.bin.gz
+	gzip -9 $(obj)/vmlinux.bin
+	mkimage -A mips -O linux -T kernel -C gzip \
+		-a $(LOADADDR) -e $(shell sh ./$(obj)/tools/entry $(NM) $(VMLINUX) ) \
+		-n 'Linux-$(KERNELRELEASE)' \
+		-d $(obj)/vmlinux.bin.gz $(obj)/uImage
+	@echo '  Kernel: arch/mips/boot/$@ is ready'
+
+zImage:
+	$(Q)$(MAKE) $(build)=$(obj)/compressed loadaddr=$(LOADADDR) $@
+	@echo '  Kernel: arch/mips/boot/compressed/$@ is ready'
+
 clean-files += addinitrd \
 	       elf2ecoff \
 	       vmlinux.bin \
 	       vmlinux.ecoff \
-	       vmlinux.srec
+	       vmlinux.srec \
+	       vmlinux.bin.gz \
+	       uImage \
+	       zImage
diff -ru linux-2.6/arch/mips/Kconfig /plain/src/qi/linux-2.6.27.git.svn/arch/mips/Kconfig
--- linux-2.6/arch/mips/Kconfig	2009-08-18 00:01:01.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/arch/mips/Kconfig	2009-08-12 10:39:09.000000000 +0200
@@ -19,6 +19,90 @@
 	prompt "System type"
 	default SGI_IP22
 
+config JZ4730_PMP
+	bool "Ingenic JZ4730 PMP board"
+	select DMA_NONCOHERENT
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SOC_JZ4730
+
+config JZ4740_PAVO
+	bool "Ingenic JZ4740 PAVO board"
+	select DMA_NONCOHERENT
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SOC_JZ4740
+
+config JZ4740_LEO
+	bool "Ingenic JZ4740 LEO board"
+	select DMA_NONCOHERENT
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SOC_JZ4740
+
+config JZ4740_LYRA
+	bool "Ingenic JZ4740 LYRA board"
+	select DMA_NONCOHERENT
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SOC_JZ4740
+
+config JZ4725_DIPPER
+	bool "Ingenic JZ4725 DIPPER board"
+	select DMA_NONCOHERENT
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SOC_JZ4740
+	select SOC_JZ4725
+
+config JZ4720_VIRGO
+	bool "Ingenic JZ4720 VIRGO board"
+	select DMA_NONCOHERENT
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SOC_JZ4740
+	select SOC_JZ4720
+
+config JZ4750_FUWA
+	bool "Ingenic JZ4750 FUWA board"
+	select DMA_NONCOHERENT
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SOC_JZ4750
+	select JZ_FPGA
+
+config JZ4750_APUS
+	bool "Ingenic JZ4750 APUS board"
+	select DMA_NONCOHERENT
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SOC_JZ4750
+
+config JZ4750D_CETUS
+	bool "Ingenic JZ4750D CETUS board"
+	select DMA_NONCOHERENT
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SOC_JZ4750D
+
+config JZ4760_F4760
+	bool "Ingenic JZ4760 FPGA board"
+	select DMA_NONCOHERENT
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SOC_JZ4760
+	select JZ_FPGA
+
 config MACH_ALCHEMY
 	bool "Alchemy processor based machines"
 
@@ -610,6 +694,52 @@
 
 endmenu
 
+#####################################################
+# Ingenic SOC series
+#####################################################
+
+config SOC_JZ4730
+	bool
+	select JZSOC
+
+config SOC_JZ4740
+	bool
+	select JZSOC
+
+config SOC_JZ4725
+	bool
+	select JZSOC
+
+config SOC_JZ4720
+	bool
+	select JZSOC
+
+config SOC_JZ4750
+	bool
+	select JZSOC
+
+config SOC_JZ4750D
+	bool
+	select JZSOC
+
+config SOC_JZ4760
+	bool
+	select JZSOC
+
+config JZ_FPGA
+	bool
+
+config JZSOC
+	bool
+	select JZRISC
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_SUPPORTS_32BIT_KERNEL
+
+config JZRISC
+	bool
+
+####################################################
+
 config GENERIC_LOCKBREAK
 	bool
 	default y
@@ -1740,6 +1870,14 @@
 
 source "kernel/time/Kconfig"
 
+# the value of (max order + 1)
+config FORCE_MAX_ZONEORDER
+	prompt "MAX_ZONEORDER"
+	int
+	default "12"
+	help
+	 The max memory that can be allocated = 4KB * 2^(CONFIG_FORCE_MAX_ZONEORDER - 1)
+
 #
 # Timer Interrupt Frequency Configuration
 #
@@ -2013,6 +2151,23 @@
 
 endmenu
 
+menu "CPU Frequency scaling"
+
+config CPU_FREQ_JZ
+	tristate "CPUfreq driver for JZ CPUs"
+	depends on JZSOC
+	default n
+	help
+	  This enables the CPUfreq driver for JZ CPUs.
+
+	  If in doubt, say N.
+
+if (CPU_FREQ_JZ)
+source "drivers/cpufreq/Kconfig"
+endif
+
+endmenu
+
 menu "Power management options"
 
 config ARCH_SUSPEND_POSSIBLE
diff -ru linux-2.6/arch/mips/kernel/cpu-probe.c /plain/src/qi/linux-2.6.27.git.svn/arch/mips/kernel/cpu-probe.c
--- linux-2.6/arch/mips/kernel/cpu-probe.c	2009-08-17 23:58:00.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/arch/mips/kernel/cpu-probe.c	2009-08-12 10:39:09.000000000 +0200
@@ -153,6 +153,7 @@
 	case CPU_25KF:
 	case CPU_PR4450:
 	case CPU_BCM3302:
+	case CPU_JZRISC:
 		cpu_wait = r4k_wait;
 		break;
 
@@ -813,6 +814,22 @@
 	}
 }
 
+static inline void cpu_probe_ingenic(struct cpuinfo_mips *c)
+{
+	decode_configs(c);
+	c->options &= ~MIPS_CPU_COUNTER; /* JZRISC does not implement the CP0 counter. */
+	switch (c->processor_id & 0xff00) {
+	case PRID_IMP_JZRISC:
+		c->cputype = CPU_JZRISC;
+		c->isa_level = MIPS_CPU_ISA_M32R1;
+		c->tlbsize = 32;
+		break;
+	default:
+		panic("Unknown Ingenic Processor ID!");
+		break;
+	}
+}
+
 const char *__cpu_name[NR_CPUS];
 
 /*
@@ -894,6 +911,7 @@
 	case CPU_BCM4710:	name = "Broadcom BCM4710"; break;
 	case CPU_PR4450:	name = "Philips PR4450"; break;
 	case CPU_LOONGSON2:	name = "ICT Loongson-2"; break;
+	case CPU_JZRISC:	name = "Ingenic JZRISC"; break;
 	default:
 		BUG();
 	}
@@ -933,6 +951,9 @@
 	case PRID_COMP_NXP:
 		cpu_probe_nxp(c);
 		break;
+ 	case PRID_COMP_INGENIC:
+		cpu_probe_ingenic(c);
+		break;
 	default:
 		c->cputype = CPU_UNKNOWN;
 	}
diff -ru linux-2.6/arch/mips/kernel/signal.c /plain/src/qi/linux-2.6.27.git.svn/arch/mips/kernel/signal.c
--- linux-2.6/arch/mips/kernel/signal.c	2009-08-17 23:58:00.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/arch/mips/kernel/signal.c	2009-08-12 10:39:09.000000000 +0200
@@ -351,6 +351,7 @@
 		if (!access_ok(VERIFY_READ, act, sizeof(*act)))
 			return -EFAULT;
 		err |= __get_user(new_ka.sa.sa_handler, &act->sa_handler);
+		err |= __get_user(new_ka.sa.sa_restorer, &act->sa_restorer);
 		err |= __get_user(new_ka.sa.sa_flags, &act->sa_flags);
 		err |= __get_user(mask, &act->sa_mask.sig[0]);
 		if (err)
@@ -366,6 +367,7 @@
 			return -EFAULT;
 		err |= __put_user(old_ka.sa.sa_flags, &oact->sa_flags);
 		err |= __put_user(old_ka.sa.sa_handler, &oact->sa_handler);
+		err |= __put_user(old_ka.sa.sa_restorer, &oact->sa_restorer);
 		err |= __put_user(old_ka.sa.sa_mask.sig[0], oact->sa_mask.sig);
 		err |= __put_user(0, &oact->sa_mask.sig[1]);
 		err |= __put_user(0, &oact->sa_mask.sig[2]);
@@ -565,6 +567,10 @@
 	regs->regs[31] = (unsigned long) frame->rs_code;
 	regs->cp0_epc = regs->regs[25] = (unsigned long) ka->sa.sa_handler;
 
+	/* Add for bionic. I'm not sure whether it works. */
+	if (ka->sa.sa_flags & SA_RESTORER)
+		regs->regs[31] = (unsigned long)ka->sa.sa_restorer;
+
 	DEBUGP("SIG deliver (%s:%d): sp=0x%p pc=0x%lx ra=0x%lx\n",
 	       current->comm, current->pid,
 	       frame, regs->cp0_epc, regs->regs[31]);
diff -ru linux-2.6/arch/mips/kernel/unaligned.c /plain/src/qi/linux-2.6.27.git.svn/arch/mips/kernel/unaligned.c
--- linux-2.6/arch/mips/kernel/unaligned.c	2009-08-17 23:58:00.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/arch/mips/kernel/unaligned.c	2009-08-12 10:39:09.000000000 +0200
@@ -497,6 +497,11 @@
 	send_sig(SIGILL, current, 1);
 }
 
+#if defined(CONFIG_JZ_TCSM)
+#undef user_mode
+#define user_mode(regs) ((((regs)->cp0_status & KU_MASK) == KU_USER) || (regs->cp0_badvaddr < 0x80000000))
+#endif
+
 asmlinkage void do_ade(struct pt_regs *regs)
 {
 	extern int do_dsemulret(struct pt_regs *);
diff -ru linux-2.6/arch/mips/Makefile /plain/src/qi/linux-2.6.27.git.svn/arch/mips/Makefile
--- linux-2.6/arch/mips/Makefile	2009-08-17 23:58:00.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/arch/mips/Makefile	2009-08-12 10:39:09.000000000 +0200
@@ -167,6 +167,46 @@
 #
 
 #
+# Commond Ingenic JZ4730 series
+#
+core-$(CONFIG_SOC_JZ4730)	+= arch/mips/jz4730/
+cflags-$(CONFIG_SOC_JZ4730)	+= -Iinclude/asm-mips/mach-jz4730
+load-$(CONFIG_SOC_JZ4730)	+= 0xffffffff80010000
+
+#
+# Commond Ingenic JZ4740 series
+#
+
+core-$(CONFIG_SOC_JZ4740)	+= arch/mips/jz4740/
+cflags-$(CONFIG_SOC_JZ4740)	+= -Iinclude/asm-mips/mach-jz4740
+load-$(CONFIG_SOC_JZ4740)	+= 0xffffffff80010000
+
+#
+# Commond Ingenic JZ4750 series
+#
+
+core-$(CONFIG_SOC_JZ4750)	+= arch/mips/jz4750/
+cflags-$(CONFIG_SOC_JZ4750)	+= -Iinclude/asm-mips/mach-jz4750
+load-$(CONFIG_SOC_JZ4750)	+= 0xffffffff80010000
+
+
+#
+# Commond Ingenic JZ4750D series
+#
+
+core-$(CONFIG_SOC_JZ4750D)	+= arch/mips/jz4750d/
+cflags-$(CONFIG_SOC_JZ4750D)	+= -Iinclude/asm-mips/mach-jz4750d
+load-$(CONFIG_SOC_JZ4750D)	+= 0xffffffff80010000
+
+#
+# Commond Ingenic JZ4760 series
+#
+
+core-$(CONFIG_SOC_JZ4760)	+= arch/mips/jz4760/
+cflags-$(CONFIG_SOC_JZ4760)	+= -Iinclude/asm-mips/mach-jz4760
+load-$(CONFIG_SOC_JZ4760)	+= 0xffffffff80010000
+
+#
 # Acer PICA 61, Mips Magnum 4000 and Olivetti M700.
 #
 core-$(CONFIG_MACH_JAZZ)	+= arch/mips/jazz/
@@ -673,6 +713,12 @@
 
 all:	$(all-y)
 
+uImage: $(vmlinux-32)
+	+@$(call makeboot,$@)
+
+zImage: $(vmlinux-32)
+	+@$(call makeboot,$@)
+
 vmlinux.bin: $(vmlinux-32)
 	+@$(call makeboot,$@)
 
@@ -697,6 +743,7 @@
 
 archclean:
 	@$(MAKE) $(clean)=arch/mips/boot
+	@$(MAKE) $(clean)=arch/mips/boot/compressed
 	@$(MAKE) $(clean)=arch/mips/lasat
 
 define archhelp
@@ -703,6 +746,9 @@
 	echo '  vmlinux.ecoff        - ECOFF boot image'
 	echo '  vmlinux.bin          - Raw binary boot image'
 	echo '  vmlinux.srec         - SREC boot image'
+	echo  '  uImage	- u-boot format image (arch/$(ARCH)/boot/uImage)'
+	echo  '  zImage	- Compressed binary image (arch/$(ARCH)/boot/compressed/zImage)'
+	echo  '  vmlinux.bin	- Uncompressed binary image (arch/$(ARCH)/boot/vmlinux.bin)'
 	echo
 	echo '  These will be default as apropriate for a configured platform.'
 endef
diff -ru linux-2.6/arch/mips/mm/cache.c /plain/src/qi/linux-2.6.27.git.svn/arch/mips/mm/cache.c
--- linux-2.6/arch/mips/mm/cache.c	2009-08-17 23:58:00.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/arch/mips/mm/cache.c	2009-08-12 10:39:09.000000000 +0200
@@ -51,6 +51,8 @@
 void (*_dma_cache_inv)(unsigned long start, unsigned long size);
 
 EXPORT_SYMBOL(_dma_cache_wback_inv);
+EXPORT_SYMBOL(_dma_cache_wback);
+EXPORT_SYMBOL(_dma_cache_inv);
 
 #endif /* CONFIG_DMA_NONCOHERENT */
 
diff -ru linux-2.6/arch/mips/mm/c-r4k.c /plain/src/qi/linux-2.6.27.git.svn/arch/mips/mm/c-r4k.c
--- linux-2.6/arch/mips/mm/c-r4k.c	2009-08-17 23:58:00.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/arch/mips/mm/c-r4k.c	2009-08-12 10:39:09.000000000 +0200
@@ -895,6 +895,36 @@
 		c->dcache.waybit = 0;
 		break;
 
+	case CPU_JZRISC:
+		config1 = read_c0_config1();
+		config1 = (config1 >> 22) & 0x07;
+		if (config1 == 0x07)
+			config1 = 10;
+		else
+			config1 = config1 + 11;
+		config1 += 2;
+		icache_size = (1 << config1);
+		c->icache.linesz = 32;
+		c->icache.ways = 4;
+		c->icache.waybit = __ffs(icache_size / c->icache.ways);
+
+		config1 = read_c0_config1();
+		config1 = (config1 >> 13) & 0x07;
+		if (config1 == 0x07)
+			config1 = 10;
+		else
+			config1 = config1 + 11;
+		config1 += 2;
+		dcache_size = (1 << config1);
+		c->dcache.linesz = 32;
+		c->dcache.ways = 4;
+		c->dcache.waybit = __ffs(dcache_size / c->dcache.ways);
+
+		c->dcache.flags = 0;
+		c->options |= MIPS_CPU_PREFETCH;
+
+		break;
+
 	default:
 		if (!(config & MIPS_CONF_M))
 			panic("Don't know how to probe P-caches on this cpu.");
diff -ru linux-2.6/arch/mips/mm/tlbex.c /plain/src/qi/linux-2.6.27.git.svn/arch/mips/mm/tlbex.c
--- linux-2.6/arch/mips/mm/tlbex.c	2009-08-17 23:58:00.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/arch/mips/mm/tlbex.c	2009-08-12 10:39:09.000000000 +0200
@@ -379,6 +379,11 @@
 		tlbw(p);
 		break;
 
+	case CPU_JZRISC:
+		tlbw(p);
+		uasm_i_nop(p);
+		break;
+
 	default:
 		panic("No TLB refill handler yet (CPU type: %d)",
 		      current_cpu_data.cputype);
diff -ru linux-2.6/drivers/i2c/busses/Kconfig /plain/src/qi/linux-2.6.27.git.svn/drivers/i2c/busses/Kconfig
--- linux-2.6/drivers/i2c/busses/Kconfig	2009-08-17 23:58:01.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/i2c/busses/Kconfig	2009-08-12 10:39:09.000000000 +0200
@@ -7,6 +7,14 @@
 comment "PC SMBus host controller drivers"
 	depends on PCI
 
+config I2C_JZ47XX
+	tristate "JZ47XX I2C Interface support"
+	depends on JZSOC
+	help
+	  If you have devices in the Ingenic JZ4730/JZ4740 I2C bus, say yes to
+	  this option. This driver can also be built as a module.  If so, the
+	  module will be called i2c-jz47xx.
+
 config I2C_ALI1535
 	tristate "ALI 1535"
 	depends on PCI
diff -ru linux-2.6/drivers/i2c/busses/Makefile /plain/src/qi/linux-2.6.27.git.svn/drivers/i2c/busses/Makefile
--- linux-2.6/drivers/i2c/busses/Makefile	2009-08-17 23:58:01.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/i2c/busses/Makefile	2009-08-12 10:39:09.000000000 +0200
@@ -3,6 +3,7 @@
 #
 
 # PC SMBus host controller drivers
+obj-$(CONFIG_I2C_JZ47XX)	+= i2c-jz47xx.o
 obj-$(CONFIG_I2C_ALI1535)	+= i2c-ali1535.o
 obj-$(CONFIG_I2C_ALI1563)	+= i2c-ali1563.o
 obj-$(CONFIG_I2C_ALI15X3)	+= i2c-ali15x3.o
diff -ru linux-2.6/drivers/i2c/i2c-dev.c /plain/src/qi/linux-2.6.27.git.svn/drivers/i2c/i2c-dev.c
--- linux-2.6/drivers/i2c/i2c-dev.c	2009-08-17 23:58:01.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/i2c/i2c-dev.c	2009-08-12 10:39:09.000000000 +0200
@@ -37,6 +37,8 @@
 #include <linux/smp_lock.h>
 #include <asm/uaccess.h>
 
+extern unsigned short sub_addr;
+extern int  addr_val;
 static struct i2c_driver i2cdev_driver;
 
 /*
@@ -424,6 +426,14 @@
 	case I2C_TIMEOUT:
 		client->adapter->timeout = arg;
 		break;
+	case I2C_SET_SUB_ADDRESS:
+		addr_val = 1;
+		sub_addr = arg;
+		break;
+	case I2C_SET_CLOCK:
+		i2c_jz_setclk(arg);
+		break;
+
 	default:
 		/* NOTE:  returning a fault code here could cause trouble
 		 * in buggy userspace code.  Some old kernel bugs returned
diff -ru linux-2.6/drivers/input/keyboard/Kconfig /plain/src/qi/linux-2.6.27.git.svn/drivers/input/keyboard/Kconfig
--- linux-2.6/drivers/input/keyboard/Kconfig	2009-08-17 23:58:01.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/input/keyboard/Kconfig	2009-08-12 10:39:09.000000000 +0200
@@ -280,6 +280,39 @@
 	  To compile this driver as a module, choose M here: the
 	  module will be called aaed2000_kbd.
 
+config KEYBOARD_JZ_GPIO
+	tristate "JZ keypad driver based on GPIO Buttons"
+	depends on JZSOC
+	help
+	  This driver implements support for buttons connected
+	  to GPIO pins of various CPUs (and some other chips).
+
+	  Say Y here if your device has buttons connected
+	  directly to such GPIO pins.  Your board-specific
+	  setup logic must also provide a platform device,
+	  with configuration data saying which GPIOs are used.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called jz_gpio_keypad.
+
+config KEYBOARD_JZ
+	tristate "JZ keypad support"
+	depends on JZSOC
+	help
+	  Enable Y here to support JZ keypad.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called jz_keypad.
+
+config KEYBOARD_JZ_5x5
+	tristate "JZ 5x5 keypad support"
+	depends on JZSOC
+	help
+	  Enable Y here to support JZ keypad.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called jz_keypad_5x5.
+
 config KEYBOARD_GPIO
 	tristate "GPIO Buttons"
 	depends on GENERIC_GPIO
diff -ru linux-2.6/drivers/input/keyboard/Makefile /plain/src/qi/linux-2.6.27.git.svn/drivers/input/keyboard/Makefile
--- linux-2.6/drivers/input/keyboard/Makefile	2009-08-17 23:58:01.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/input/keyboard/Makefile	2009-08-12 10:39:09.000000000 +0200
@@ -20,6 +20,9 @@
 obj-$(CONFIG_KEYBOARD_HIL_OLD)		+= hilkbd.o
 obj-$(CONFIG_KEYBOARD_OMAP)		+= omap-keypad.o
 obj-$(CONFIG_KEYBOARD_PXA27x)		+= pxa27x_keypad.o
+obj-$(CONFIG_KEYBOARD_JZ_GPIO)		+= jz_gpio_keypad.o
+obj-$(CONFIG_KEYBOARD_JZ_5x5)		+= jz_keypad_5x5.o
+obj-$(CONFIG_KEYBOARD_JZ)		+= jz_keypad.o
 obj-$(CONFIG_KEYBOARD_AAED2000)		+= aaed2000_kbd.o
 obj-$(CONFIG_KEYBOARD_GPIO)		+= gpio_keys.o
 obj-$(CONFIG_KEYBOARD_HP6XX)		+= jornada680_kbd.o
diff -ru linux-2.6/drivers/input/touchscreen/Kconfig /plain/src/qi/linux-2.6.27.git.svn/drivers/input/touchscreen/Kconfig
--- linux-2.6/drivers/input/touchscreen/Kconfig	2009-08-17 23:58:01.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/input/touchscreen/Kconfig	2009-08-12 10:39:09.000000000 +0200
@@ -115,6 +115,24 @@
 	  To compile this driver as a module, choose M here: the
 	  module will be called inexio.
 
+config TOUCHSCREEN_JZ
+	tristate "JZ touchscreen"
+	default y
+	help
+	  Say Y here to enable JZ SAR A/D controller if you use touchscreen
+          on JZ platform.
+
+	  To compile this driver as a module, choose M here, and the
+	  module jz_ts should be called.
+
+config JZ_ADKEY
+	bool "JZ ADKEY"
+	depends on TOUCHSCREEN_JZ
+	help
+          The AD value of the key is get by JZ SAR A/D controller when any ad key
+          is pressed down.
+	
+
 config TOUCHSCREEN_MK712
 	tristate "ICS MicroClock MK712 touchscreen"
 	help
@@ -181,6 +199,12 @@
 	  To compile this driver as a module, choose M here: the
 	  module will be called migor_ts.
 
+config TOUCHSCREEN_SYNAPTICS_I2C_RMI
+	tristate "Synaptics i2c touchscreen"
+	depends on I2C
+	help
+	  This enables support for Synaptics RMI over I2C based touchscreens.
+
 config TOUCHSCREEN_TOUCHRIGHT
 	tristate "Touchright serial touchscreen"
 	select SERIO
diff -ru linux-2.6/drivers/input/touchscreen/Makefile /plain/src/qi/linux-2.6.27.git.svn/drivers/input/touchscreen/Makefile
--- linux-2.6/drivers/input/touchscreen/Makefile	2009-08-17 23:58:01.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/input/touchscreen/Makefile	2009-08-12 10:39:09.000000000 +0200
@@ -14,6 +14,7 @@
 obj-$(CONFIG_TOUCHSCREEN_ELO)		+= elo.o
 obj-$(CONFIG_TOUCHSCREEN_FUJITSU)	+= fujitsu_ts.o
 obj-$(CONFIG_TOUCHSCREEN_INEXIO)	+= inexio.o
+obj-$(CONFIG_TOUCHSCREEN_JZ)		+= jz_ts.o
 obj-$(CONFIG_TOUCHSCREEN_MIGOR)		+= migor_ts.o
 obj-$(CONFIG_TOUCHSCREEN_MTOUCH)	+= mtouch.o
 obj-$(CONFIG_TOUCHSCREEN_MK712)		+= mk712.o
@@ -22,6 +23,7 @@
 obj-$(CONFIG_TOUCHSCREEN_HTCPEN)	+= htcpen.o
 obj-$(CONFIG_TOUCHSCREEN_USB_COMPOSITE)	+= usbtouchscreen.o
 obj-$(CONFIG_TOUCHSCREEN_PENMOUNT)	+= penmount.o
+obj-$(CONFIG_TOUCHSCREEN_SYNAPTICS_I2C_RMI)	+= synaptics_i2c_rmi.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHIT213)	+= touchit213.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT)	+= touchright.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHWIN)	+= touchwin.o
diff -ru linux-2.6/drivers/misc/Kconfig /plain/src/qi/linux-2.6.27.git.svn/drivers/misc/Kconfig
--- linux-2.6/drivers/misc/Kconfig	2009-08-17 23:58:01.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/misc/Kconfig	2009-08-12 10:39:09.000000000 +0200
@@ -13,6 +13,40 @@
 
 if MISC_DEVICES
 
+config JZ_TCSM
+	bool "JZ TCSM for multimedia"
+	default y
+
+config JZ_CIM
+	bool "JZ CIM for Camera driver"
+	default y
+
+choice
+	depends on JZ_CIM
+	prompt "Camera Sensor"
+	default OV3640
+
+config OV3640
+	bool "OmniVision OV3640 sensor support (3.1 MegaPixel)"
+config OV2640
+	bool "OmniVision OV2640 sensor support (2.0 MegaPixel)"
+config OV9650
+	bool "OmniVision OV9650 sensor support (1.3 MegaPixel)"
+endchoice
+
+config ANDROID_PMEM
+	bool "Android pmem allocator"
+	default y
+
+config TIMED_OUTPUT
+	bool "Timed output class driver"
+	default y
+
+config TIMED_GPIO
+	bool "Android timed gpio driver"
+	depends on GENERIC_GPIO && TIMED_OUTPUT
+	default y
+
 config ATMEL_PWM
 	tristate "Atmel AT32/AT91 PWM support"
 	depends on AVR32 || ARCH_AT91
@@ -55,6 +89,10 @@
 	  TC can be used for other purposes, such as PWM generation and
 	  interval timing.
 
+config BINDER_IPC
+	tristate "Binder IPC Driver"
+	default y
+
 config IBM_ASM
 	tristate "Device driver for IBM RSA service processor"
 	depends on X86 && PCI && INPUT && EXPERIMENTAL
@@ -424,6 +462,13 @@
 	  driver (SCSI/ATA) which supports enclosures
 	  or a SCSI enclosure device (SES) to use these services.
 
+config KERNEL_DEBUGGER_CORE
+	bool "Kernel Debugger Core"
+	default n
+	---help---
+	  Generic kernel debugging command processor used by low level
+	  (interrupt context) platform-specific debuggers.
+
 config SGI_XP
 	tristate "Support communication between SGI SSIs"
 	depends on NET
@@ -475,4 +520,75 @@
 	This option enables addition debugging code for the SGI GRU driver. If
 	you are unsure, say N.
 
+config LOW_MEMORY_KILLER
+	tristate "Low Memory Killer"
+	---help---
+          Register processes to be killed when memory is low
+
+config LOGGER
+	bool "High-speed in-kernel logging driver"
+	default y
+
+config UID_STAT
+	bool "UID based statistics tracking exported to /proc/uid_stat"
+	default n
+
+config ANDROID_RAM_CONSOLE
+        bool "RAM buffer console"
+        default n
+
+config ANDROID_RAM_CONSOLE_ENABLE_VERBOSE
+        bool "Enable verbose console messages"
+        default y
+        depends on ANDROID_RAM_CONSOLE
+
+menuconfig ANDROID_RAM_CONSOLE_ERROR_CORRECTION
+        bool "Enable error correction"
+        default n
+        depends on ANDROID_RAM_CONSOLE
+        depends on !ANDROID_RAM_CONSOLE_EARLY_INIT
+        select REED_SOLOMON
+        select REED_SOLOMON_ENC8
+        select REED_SOLOMON_DEC8
+
+if ANDROID_RAM_CONSOLE_ERROR_CORRECTION
+
+config ANDROID_RAM_CONSOLE_ERROR_CORRECTION_DATA_SIZE
+        int "Data data size"
+        default 128
+        help
+          Must be a power of 2.
+
+config ANDROID_RAM_CONSOLE_ERROR_CORRECTION_ECC_SIZE
+        int "ECC size"
+        default 16
+
+config ANDROID_RAM_CONSOLE_ERROR_CORRECTION_SYMBOL_SIZE
+        int "Symbol size"
+        default 8
+config ANDROID_RAM_CONSOLE_ERROR_CORRECTION_POLYNOMIAL
+        hex "Polynomial"
+        default 0x19 if (ANDROID_RAM_CONSOLE_ERROR_CORRECTION_SYMBOL_SIZE = 4)
+        default 0x29 if (ANDROID_RAM_CONSOLE_ERROR_CORRECTION_SYMBOL_SIZE = 5)
+        default 0x61 if (ANDROID_RAM_CONSOLE_ERROR_CORRECTION_SYMBOL_SIZE = 6)
+        default 0x89 if (ANDROID_RAM_CONSOLE_ERROR_CORRECTION_SYMBOL_SIZE = 7)
+        default 0x11d if (ANDROID_RAM_CONSOLE_ERROR_CORRECTION_SYMBOL_SIZE = 8)
+
+endif #ANDROID_RAM_CONSOLE_ERROR_CORRECTION
+
+config ANDROID_RAM_CONSOLE_EARLY_INIT
+        bool "Start ram console early"
+        default n
+        depends on ANDROID_RAM_CONSOLE
+
+config ANDROID_RAM_CONSOLE_EARLY_ADDR
+        hex "RAM console virtual address"
+        default 0
+        depends on ANDROID_RAM_CONSOLE_EARLY_INIT
+
+config ANDROID_RAM_CONSOLE_EARLY_SIZE
+        hex "RAM console buffer size"
+        default 0
+        depends on ANDROID_RAM_CONSOLE_EARLY_INIT
+
 endif # MISC_DEVICES
diff -ru linux-2.6/drivers/misc/Makefile /plain/src/qi/linux-2.6.27.git.svn/drivers/misc/Makefile
--- linux-2.6/drivers/misc/Makefile	2009-08-17 23:58:01.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/misc/Makefile	2009-08-12 10:39:09.000000000 +0200
@@ -10,9 +10,13 @@
 obj-$(CONFIG_MSI_LAPTOP)	+= msi-laptop.o
 obj-$(CONFIG_COMPAL_LAPTOP)	+= compal-laptop.o
 obj-$(CONFIG_ACER_WMI)		+= acer-wmi.o
+obj-$(CONFIG_ANDROID_PMEM)	+= pmem.o
+obj-$(CONFIG_TIMED_OUTPUT)	+= timed_output.o
+obj-$(CONFIG_TIMED_GPIO)	+= timed_gpio.o
 obj-$(CONFIG_ATMEL_PWM)		+= atmel_pwm.o
 obj-$(CONFIG_ATMEL_SSC)		+= atmel-ssc.o
 obj-$(CONFIG_ATMEL_TCLIB)	+= atmel_tclib.o
+obj-$(CONFIG_BINDER_IPC)	+= binder.o
 obj-$(CONFIG_HP_WMI)		+= hp-wmi.o
 obj-$(CONFIG_TC1100_WMI)	+= tc1100-wmi.o
 obj-$(CONFIG_LKDTM)		+= lkdtm.o
@@ -26,7 +30,14 @@
 obj-$(CONFIG_EEPROM_93CX6)	+= eeprom_93cx6.o
 obj-$(CONFIG_INTEL_MENLOW)	+= intel_menlow.o
 obj-$(CONFIG_ENCLOSURE_SERVICES) += enclosure.o
+obj-$(CONFIG_KERNEL_DEBUGGER_CORE)	+= kernel_debugger.o
 obj-$(CONFIG_KGDB_TESTS)	+= kgdbts.o
 obj-$(CONFIG_SGI_XP)		+= sgi-xp/
 obj-$(CONFIG_SGI_GRU)		+= sgi-gru/
 obj-$(CONFIG_HP_ILO)		+= hpilo.o
+obj-$(CONFIG_LOGGER)		+= logger.o
+obj-$(CONFIG_UID_STAT)		+= uid_stat.o
+obj-$(CONFIG_LOW_MEMORY_KILLER)	+= lowmemorykiller.o
+obj-$(CONFIG_ANDROID_RAM_CONSOLE)	+= ram_console.o
+obj-$(CONFIG_JZ_TCSM)		+= jz_tcsm.o
+obj-$(CONFIG_JZ_CIM)		+= jz_sensor.o jz_cim.o
diff -ru linux-2.6/drivers/mmc/card/block.c /plain/src/qi/linux-2.6.27.git.svn/drivers/mmc/card/block.c
--- linux-2.6/drivers/mmc/card/block.c	2009-08-17 23:58:01.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/mmc/card/block.c	2009-08-12 10:39:09.000000000 +0200
@@ -228,7 +228,11 @@
 		brq.mrq.cmd = &brq.cmd;
 		brq.mrq.data = &brq.data;
 
+#ifdef CONFIG_JZ4750_BOOT_FROM_MSC0
+		brq.cmd.arg = req->sector + 8192;
+#else
 		brq.cmd.arg = req->sector;
+#endif
 		if (!mmc_card_blockaddr(card))
 			brq.cmd.arg <<= 9;
 		brq.cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_ADTC;
@@ -594,6 +598,9 @@
 
 	if (md) {
 		mmc_blk_set_blksize(md, card);
+#ifdef CONFIG_MMC_BLOCK_PARANOID_RESUME
+		md->queue.check_status = 1;
+#endif
 		mmc_queue_resume(&md->queue);
 	}
 	return 0;
diff -ru linux-2.6/drivers/mmc/core/mmc.c /plain/src/qi/linux-2.6.27.git.svn/drivers/mmc/core/mmc.c
--- linux-2.6/drivers/mmc/core/mmc.c	2009-08-17 23:58:01.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/mmc/core/mmc.c	2009-08-12 10:39:09.000000000 +0200
@@ -140,8 +140,12 @@
 
 	e = UNSTUFF_BITS(resp, 47, 3);
 	m = UNSTUFF_BITS(resp, 62, 12);
+#ifdef CONFIG_JZ4750_BOOT_FROM_MSC0
 	csd->capacity	  = (1 + m) << (e + 2);
-
+	csd->capacity	  -= 8192;
+#else
+	csd->capacity	  = (1 + m) << (e + 2);
+#endif
 	csd->read_blkbits = UNSTUFF_BITS(resp, 80, 4);
 	csd->read_partial = UNSTUFF_BITS(resp, 79, 1);
 	csd->write_misalign = UNSTUFF_BITS(resp, 78, 1);
diff -ru linux-2.6/drivers/mmc/core/sd.c /plain/src/qi/linux-2.6.27.git.svn/drivers/mmc/core/sd.c
--- linux-2.6/drivers/mmc/core/sd.c	2009-08-17 23:58:01.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/mmc/core/sd.c	2009-08-12 10:39:09.000000000 +0200
@@ -109,8 +109,12 @@
 
 		e = UNSTUFF_BITS(resp, 47, 3);
 		m = UNSTUFF_BITS(resp, 62, 12);
+#ifdef CONFIG_JZ4750_BOOT_FROM_MSC0
 		csd->capacity	  = (1 + m) << (e + 2);
-
+		csd->capacity	  -= 8192;
+#else
+		csd->capacity	  = (1 + m) << (e + 2);
+#endif
 		csd->read_blkbits = UNSTUFF_BITS(resp, 80, 4);
 		csd->read_partial = UNSTUFF_BITS(resp, 79, 1);
 		csd->write_misalign = UNSTUFF_BITS(resp, 78, 1);
@@ -137,7 +141,12 @@
 		csd->cmdclass	  = UNSTUFF_BITS(resp, 84, 12);
 
 		m = UNSTUFF_BITS(resp, 48, 22);
+#ifdef CONFIG_JZ4750_BOOT_FROM_MSC0
+		csd->capacity     = (1 + m) << 10;
+		csd->capacity	 -= 8192;
+#else
 		csd->capacity     = (1 + m) << 10;
+#endif
 
 		csd->read_blkbits = 9;
 		csd->read_partial = 0;
@@ -336,7 +345,9 @@
 	int err;
 	u32 cid[4];
 	unsigned int max_dtr;
-
+#ifdef CONFIG_MMC_PARANOID_SD_INIT
+	int retries;
+#endif
 	BUG_ON(!host);
 	WARN_ON(!host->claimed);
 
@@ -448,11 +459,29 @@
 		err = mmc_decode_scr(card);
 		if (err < 0)
 			goto free_card;
-
 		/*
 		 * Fetch switch information from card.
 		 */
+#ifdef CONFIG_MMC_PARANOID_SD_INIT
+		for (retries = 1; retries <= 3; retries++) {
+			err = mmc_read_switch(card);
+			if (!err) {
+				if (retries > 1) {
+					printk(KERN_WARNING
+					       "%s: recovered\n", 
+					       mmc_hostname(host));
+				}
+				break;
+			} else {
+				printk(KERN_WARNING
+				       "%s: read switch failed (attempt %d)\n",
+				       mmc_hostname(host), retries);
+			}
+		}
+#else
 		err = mmc_read_switch(card);
+#endif
+
 		if (err)
 			goto free_card;
 	}
@@ -535,18 +564,37 @@
  */
 static void mmc_sd_detect(struct mmc_host *host)
 {
-	int err;
+	int err = 0;
+#ifdef CONFIG_MMC_PARANOID_SD_INIT
+        int retries = 5;
+#endif
 
 	BUG_ON(!host);
 	BUG_ON(!host->card);
-
+       
 	mmc_claim_host(host);
 
 	/*
 	 * Just check if our card has been removed.
 	 */
+#ifdef CONFIG_MMC_PARANOID_SD_INIT
+	while(retries) {
+		err = mmc_send_status(host->card, NULL);
+		printk("%s(%s): err = %d\n", __func__, mmc_hostname(host), err);
+		if (err) {
+			retries--;
+			udelay(5);
+			continue;
+		}
+		break;
+	}
+	if (!retries) {
+		printk(KERN_ERR "%s(%s): Unable to re-detect card (%d)\n",
+		       __func__, mmc_hostname(host), err);
+	}
+#else
 	err = mmc_send_status(host->card, NULL);
-
+#endif
 	mmc_release_host(host);
 
 	if (err) {
@@ -584,12 +632,31 @@
 static void mmc_sd_resume(struct mmc_host *host)
 {
 	int err;
+#ifdef CONFIG_MMC_PARANOID_SD_INIT
+	int retries;
+#endif
 
 	BUG_ON(!host);
 	BUG_ON(!host->card);
 
 	mmc_claim_host(host);
+#ifdef CONFIG_MMC_PARANOID_SD_INIT
+	retries = 5;
+	while (retries) {
+		err = mmc_sd_init_card(host, host->ocr, host->card);
+
+		if (err) {
+			printk(KERN_ERR "%s: Re-init card rc = %d (retries = %d)\n",
+			       mmc_hostname(host), err, retries);
+			mdelay(5);
+			retries--;
+			continue;
+		}
+		break;
+	}
+#else
 	err = mmc_sd_init_card(host, host->ocr, host->card);
+#endif
 	mmc_release_host(host);
 
 	if (err) {
@@ -622,6 +689,9 @@
 int mmc_attach_sd(struct mmc_host *host, u32 ocr)
 {
 	int err;
+#ifdef CONFIG_MMC_PARANOID_SD_INIT
+	int retries;
+#endif
 
 	BUG_ON(!host);
 	WARN_ON(!host->claimed);
@@ -670,9 +740,27 @@
 	/*
 	 * Detect and init the card.
 	 */
+#ifdef CONFIG_MMC_PARANOID_SD_INIT
+	retries = 5;
+	while (retries) {
+		err = mmc_sd_init_card(host, host->ocr, NULL);
+		if (err) {
+			retries--;
+			continue;
+		}
+		break;
+	}
+
+	if (!retries) {
+		printk(KERN_ERR "%s: mmc_sd_init_card() failure (err = %d)\n",
+		       mmc_hostname(host), err);
+		goto err;
+	}
+#else
 	err = mmc_sd_init_card(host, host->ocr, NULL);
 	if (err)
 		goto err;
+#endif
 
 	mmc_release_host(host);
 
diff -ru linux-2.6/drivers/mmc/host/Kconfig /plain/src/qi/linux-2.6.27.git.svn/drivers/mmc/host/Kconfig
--- linux-2.6/drivers/mmc/host/Kconfig	2009-08-17 23:58:01.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/mmc/host/Kconfig	2009-08-12 10:39:09.000000000 +0200
@@ -4,6 +4,104 @@
 
 comment "MMC/SD Host Controller Drivers"
 
+config MMC_JZ
+	tristate "JZ SD/Multimedia Card Interface support"
+	depends on SOC_JZ4730 || SOC_JZ4740
+	help
+	  This selects the Ingenic JZ4730/JZ4740 SD/Multimedia card Interface.
+	  If you have abIngenic platform with a Multimedia Card slot,
+	  say Y or M here.
+
+	  If unsure, say N.
+choice
+	depends on MMC_JZ
+	prompt "MMC BUS Width"
+	default JZ_MMC_BUS_4
+	help
+	This defines the BUS Width of the Ingenic JZ4730/JZ4740 SD/Multimedia card Interface.
+
+config JZ_MMC_BUS_1
+	bool "1 Bit Bus"
+	help
+	 1 Bit SD/Multimedia Card Bus
+
+config JZ_MMC_BUS_4
+	bool "4 Bit Bus"
+	help
+	 4 Bit SD/Multimedia Card Bus
+
+endchoice
+
+config MSC0_JZ4750
+	tristate "JZ4750 SD/Multimedia Card 0 Interface support"
+	depends on SOC_JZ4750 || SOC_JZ4750D
+	help
+	  This selects the Ingenic JZ4750 SD/Multimedia card 0 Interface.
+	  If you have a Ingenic platform with a Multimedia Card slot,
+	  say Y or M here.
+
+	  If unsure, say N.
+
+choice
+	depends on MSC0_JZ4750
+	prompt "MSC0 BUS Width"
+	default JZ4750_MSC0_BUS_4
+	help
+	This defines the BUS Width of the Ingenic JZ4750 SD/Multimedia card Interface.
+
+config JZ4750_MSC0_BUS_1
+	bool "1 Bit Bus"
+	help
+	 1 Bit SD/Multimedia Card Bus
+
+config JZ4750_MSC0_BUS_4
+	bool "4 Bit Bus"
+	help
+	 4 Bit SD/Multimedia Card Bus
+
+config JZ4750_MSC0_BUS_8
+	bool "8 Bit Bus"
+	help
+	 8 Bit Multimedia Card Bus
+
+endchoice
+
+config MSC1_JZ4750
+	tristate "JZ4750 SD/Multimedia Card 1 Interface support"
+	depends on SOC_JZ4750 || SOC_JZ4750D
+	help
+	  This selects the Ingenic JZ4750 SD/Multimedia card 1 Interface.
+	  If you have a Ingenic platform with a Multimedia Card slot,
+	  say Y or M here.
+
+	  If unsure, say N.
+
+choice
+	depends on MSC1_JZ4750
+	prompt "MSC1 BUS Width"
+	default JZ4750_MSC1_BUS_4
+	help
+	This defines the BUS Width of the Ingenic JZ4750 SD/Multimedia card Interface.
+
+config JZ4750_MSC1_BUS_1
+	bool "1 Bit Bus"
+	help
+	 1 Bit SD/Multimedia Card Bus
+
+config JZ4750_MSC1_BUS_4
+	bool "4 Bit Bus"
+	help
+	 4 Bit SD/Multimedia Card Bus
+endchoice
+
+config JZ4750_BOOT_FROM_MSC0
+	tristate "JZ4750 Boot from SD/Multimedia Card Interface support"
+	depends on SOC_JZ4750 || SOC_JZ4750D
+	help
+	  This selects boot from the Sd/Multimedia Card.
+
+	  If unsure,say N.
+
 config MMC_ARMMMCI
 	tristate "ARM AMBA Multimedia Card Interface support"
 	depends on ARM_AMBA
diff -ru linux-2.6/drivers/mmc/host/Makefile /plain/src/qi/linux-2.6.27.git.svn/drivers/mmc/host/Makefile
--- linux-2.6/drivers/mmc/host/Makefile	2009-08-17 23:58:01.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/mmc/host/Makefile	2009-08-12 10:39:09.000000000 +0200
@@ -6,6 +6,9 @@
 	EXTRA_CFLAGS		+= -DDEBUG
 endif
 
+obj-$(CONFIG_MMC_JZ)		+= jz_mmc.o
+obj-$(CONFIG_MSC0_JZ4750)	+= jz4750_mmc.o
+obj-$(CONFIG_MSC1_JZ4750)	+= jz4750_mmc.o
 obj-$(CONFIG_MMC_ARMMMCI)	+= mmci.o
 obj-$(CONFIG_MMC_PXA)		+= pxamci.o
 obj-$(CONFIG_MMC_IMX)		+= imxmmc.o
diff -ru linux-2.6/drivers/net/Kconfig /plain/src/qi/linux-2.6.27.git.svn/drivers/net/Kconfig
--- linux-2.6/drivers/net/Kconfig	2009-08-17 23:58:01.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/net/Kconfig	2009-08-12 10:39:09.000000000 +0200
@@ -207,6 +207,33 @@
 	  or internal device.  It is safe to say Y or M here even if your
 	  ethernet card lack MII.
 
+config JZ_ETH
+	tristate "JZ4730/JZ5730 On-Chip Ethernet support"
+	depends on NET_ETHERNET && (SOC_JZ4730 || SOC_JZ5730 || JZ_FPGA)
+	help
+	  Say Y for support of JZ4730/JZ5730 On-Chip Ethernet interface.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called jz_eth.
+
+config JZCS8900
+	tristate "JZ CS8900A Ethernet support"
+	depends on NET_ETHERNET && (SOC_JZ4740 || SOC_JZ4750)
+	help
+	  Say Y for support of JZ CS8900A Ethernet interface.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called jzcs8900a.
+
+config JZ4760_ETH
+	tristate "JZ4760 On-Chip Ethernet support"
+	depends on NET_ETHERNET && (SOC_JZ4760 || SOC_JZ4810 || JZ_FPGA)
+	help
+	  Say Y for support of JZ4760 On-Chip Ethernet interface.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called jz4760_eth.
+
 config MACB
 	tristate "Atmel MACB support"
 	depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91CAP9
diff -ru linux-2.6/drivers/net/Makefile /plain/src/qi/linux-2.6.27.git.svn/drivers/net/Makefile
--- linux-2.6/drivers/net/Makefile	2009-08-17 23:58:01.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/net/Makefile	2009-08-12 10:39:09.000000000 +0200
@@ -90,6 +90,9 @@
 obj-$(CONFIG_MII) += mii.o
 obj-$(CONFIG_PHYLIB) += phy/
 
+obj-$(CONFIG_JZ_ETH) += jz_eth.o
+obj-$(CONFIG_JZCS8900) += jzcs8900a.o
+obj-$(CONFIG_JZ4760_ETH) += jz4760_eth.o
 obj-$(CONFIG_SUNDANCE) += sundance.o
 obj-$(CONFIG_HAMACHI) += hamachi.o
 obj-$(CONFIG_NET) += Space.o loopback.o
diff -ru linux-2.6/drivers/power/Kconfig /plain/src/qi/linux-2.6.27.git.svn/drivers/power/Kconfig
--- linux-2.6/drivers/power/Kconfig	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/power/Kconfig	2009-08-12 10:39:09.000000000 +0200
@@ -62,4 +62,9 @@
 	help
 	  Say Y to enable support for the battery in Palm T|X.
 
+config BATTERY_JZ
+	tristate "JZ battery"
+	help
+	  Say Y to enable support for the battery in JZ SOC.
+
 endif # POWER_SUPPLY
diff -ru linux-2.6/drivers/power/Makefile /plain/src/qi/linux-2.6.27.git.svn/drivers/power/Makefile
--- linux-2.6/drivers/power/Makefile	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/power/Makefile	2009-08-12 10:39:09.000000000 +0200
@@ -22,3 +22,4 @@
 obj-$(CONFIG_BATTERY_OLPC)	+= olpc_battery.o
 obj-$(CONFIG_BATTERY_TOSA)	+= tosa_battery.o
 obj-$(CONFIG_BATTERY_PALMTX)	+= palmtx_battery.o
+obj-$(CONFIG_BATTERY_JZ)	+= jz_battery.o
diff -ru linux-2.6/drivers/power/power_supply_sysfs.c /plain/src/qi/linux-2.6.27.git.svn/drivers/power/power_supply_sysfs.c
--- linux-2.6/drivers/power/power_supply_sysfs.c	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/power/power_supply_sysfs.c	2009-08-12 10:39:09.000000000 +0200
@@ -107,7 +107,8 @@
 	POWER_SUPPLY_ATTR(energy_now),
 	POWER_SUPPLY_ATTR(energy_avg),
 	POWER_SUPPLY_ATTR(capacity),
-	POWER_SUPPLY_ATTR(temp),
+	POWER_SUPPLY_ATTR(batt_temp),
+	POWER_SUPPLY_ATTR(batt_vol),
 	POWER_SUPPLY_ATTR(temp_ambient),
 	POWER_SUPPLY_ATTR(time_to_empty_now),
 	POWER_SUPPLY_ATTR(time_to_empty_avg),
diff -ru linux-2.6/drivers/rtc/Kconfig /plain/src/qi/linux-2.6.27.git.svn/drivers/rtc/Kconfig
--- linux-2.6/drivers/rtc/Kconfig	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/rtc/Kconfig	2009-08-12 10:39:09.000000000 +0200
@@ -105,6 +105,16 @@
 	  driver does not expose RTC_UIE ioctls.  Those requests generate
 	  once-per-second update interrupts, used for synchronization.
 
+config RTC_INTF_ALARM
+	bool "Android alarm driver"
+	depends on RTC_CLASS
+	default y
+	help
+	  Provides non-wakeup and rtc backed wakeup alarms based on rtc or
+	  elapsed realtime, and a non-wakeup alarm on the monotonic clock.
+	  Also provides an ioctl to set the wall time which must be used
+	  for elapsed realtime to work.
+
 config RTC_DRV_TEST
 	tristate "Test driver/device"
 	help
@@ -468,6 +478,16 @@
 	  To compile this driver as a module, choose M here: the
 	  module will be called rtc-sa1100.
 
+config RTC_DRV_JZ4750
+	tristate "JZ4750/JZ4750D"
+	depends on SOC_JZ4750 || SOC_JZ4750D
+	help
+	  If you say Y here you will get access to the real time clock
+	  built into your JZ4750 or JZ4750D CPU.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called rtc-jz4750.
+
 config RTC_DRV_SH
 	tristate "SuperH On-Chip RTC"
 	depends on RTC_CLASS && SUPERH
diff -ru linux-2.6/drivers/rtc/Makefile /plain/src/qi/linux-2.6.27.git.svn/drivers/rtc/Makefile
--- linux-2.6/drivers/rtc/Makefile	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/rtc/Makefile	2009-08-12 10:39:09.000000000 +0200
@@ -11,6 +11,7 @@
 obj-$(CONFIG_RTC_CLASS)		+= rtc-core.o
 rtc-core-y			:= class.o interface.o
 
+rtc-core-$(CONFIG_RTC_INTF_ALARM) += alarm.o
 rtc-core-$(CONFIG_RTC_INTF_DEV)	+= rtc-dev.o
 rtc-core-$(CONFIG_RTC_INTF_PROC) += rtc-proc.o
 rtc-core-$(CONFIG_RTC_INTF_SYSFS) += rtc-sysfs.o
@@ -59,3 +60,4 @@
 obj-$(CONFIG_RTC_DRV_V3020)	+= rtc-v3020.o
 obj-$(CONFIG_RTC_DRV_VR41XX)	+= rtc-vr41xx.o
 obj-$(CONFIG_RTC_DRV_X1205)	+= rtc-x1205.o
+obj-$(CONFIG_RTC_DRV_JZ4750)	+= rtc-jz4750.o
diff -ru linux-2.6/drivers/serial/8250.c /plain/src/qi/linux-2.6.27.git.svn/drivers/serial/8250.c
--- linux-2.6/drivers/serial/8250.c	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/serial/8250.c	2009-08-12 10:39:09.000000000 +0200
@@ -178,7 +178,7 @@
 	[PORT_16550A] = {
 		.name		= "16550A",
 		.fifo_size	= 16,
-		.tx_loadsz	= 16,
+		.tx_loadsz	= 8,
 		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
 		.flags		= UART_CAP_FIFO,
 	},
@@ -397,6 +397,10 @@
 		break;
 
 	case UPIO_MEM:
+#if defined(CONFIG_JZSOC)
+		if (offset == (UART_FCR << up->port.regshift))
+			value |= 0x10; /* set FCR.UUE */
+#endif
 		writeb(value, up->port.membase + offset);
 		break;
 
@@ -2057,6 +2061,83 @@
 		serial_unlink_irq_chain(up);
 }
 
+#if defined(CONFIG_JZSOC) && !defined(CONFIG_SOC_JZ4730)
+static unsigned short quot1[3] = {0}; /* quot[0]:baud_div, quot[1]:umr, quot[2]:uacr */
+static unsigned short * serial8250_get_divisor(struct uart_port *port, unsigned int baud)
+{
+	int err, sum, i, j;
+	int a[12], b[12];
+	unsigned short div, umr, uacr;
+	unsigned short umr_best, div_best, uacr_best;
+	long long t0, t1, t2, t3;
+
+	sum = 0;
+	umr_best = div_best = uacr_best = 0;
+	div = 1;
+
+	if ((port->uartclk % (16 * baud)) == 0) {
+		quot1[0] = port->uartclk / (16 * baud);
+		quot1[1] = 16;
+		quot1[2] = 0;
+		return quot1;
+	}
+
+	while (1) {
+		umr = port->uartclk / (baud * div);
+  		if (umr > 32) {
+			div++;
+			continue;
+		}
+		if (umr < 4) {
+			break;
+		}
+		for (i = 0; i < 12; i++) {
+			a[i] = umr;
+			b[i] = 0;
+			sum = 0;
+			for (j = 0; j <= i; j++) {
+				sum += a[j];
+			}
+
+                        /* the precision could be 1/2^(36) due to the value of t0 */
+			t0 = 0x1000000000LL;
+			t1 = (i + 1) * t0;
+			t2 = (sum * div) * t0;
+			t3 = div * t0;
+			do_div(t1, baud);
+			do_div(t2, port->uartclk);
+			do_div(t3, (2 * port->uartclk));
+			err = t1 - t2 - t3;
+
+			if (err > 0) {
+				a[i] += 1;
+				b[i] = 1;
+			}
+		}
+
+		uacr = 0;
+		for (i = 0; i < 12; i++) {
+			if (b[i] == 1) {
+				uacr |= 1 << i;
+			}
+		}
+
+                /* the best value of umr should be near 16, and the value of uacr should better be smaller */
+		if (abs(umr - 16) < abs(umr_best - 16) || (abs(umr - 16) == abs(umr_best - 16) && uacr_best > uacr)) {
+			div_best = div;
+			umr_best = umr;
+			uacr_best = uacr;
+		}
+		div++;
+	}
+
+	quot1[0] = div_best;
+	quot1[1] = umr_best;
+	quot1[2] = uacr_best;
+
+	return quot1;
+}
+#else
 static unsigned int serial8250_get_divisor(struct uart_port *port, unsigned int baud)
 {
 	unsigned int quot;
@@ -2076,6 +2157,7 @@
 
 	return quot;
 }
+#endif
 
 static void
 serial8250_set_termios(struct uart_port *port, struct ktermios *termios,
@@ -2085,6 +2167,9 @@
 	unsigned char cval, fcr = 0;
 	unsigned long flags;
 	unsigned int baud, quot;
+#if defined(CONFIG_JZSOC) && !defined(CONFIG_SOC_JZ4730)
+	unsigned short *quot1;
+#endif
 
 	switch (termios->c_cflag & CSIZE) {
 	case CS5:
@@ -2117,7 +2202,12 @@
 	 * Ask the core to calculate the divisor for us.
 	 */
 	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
+#if defined(CONFIG_JZSOC) && !defined(CONFIG_SOC_JZ4730)
+	quot1 = serial8250_get_divisor(port, baud);
+	quot = quot1[0]; /* not usefull, just let gcc happy */
+#else
 	quot = serial8250_get_divisor(port, baud);
+#endif
 
 	/*
 	 * Oxford Semi 952 rev B workaround
@@ -2195,6 +2285,10 @@
 	if (up->capabilities & UART_CAP_UUE)
 		up->ier |= UART_IER_UUE | UART_IER_RTOIE;
 
+#ifdef CONFIG_JZSOC
+	up->ier |= UART_IER_RTOIE; /* Set this flag, or very slow */
+#endif
+
 	serial_out(up, UART_IER, up->ier);
 
 	if (up->capabilities & UART_CAP_EFR) {
@@ -2229,7 +2323,15 @@
 		serial_outp(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */
 	}
 
+#if defined(CONFIG_JZSOC) && !defined(CONFIG_SOC_JZ4730)
+#define UART_UMR  9
+#define UART_UACR 10
+	serial_dl_write(up, quot1[0]);
+	serial_outp(up, UART_UMR, quot1[1]);
+	serial_outp(up, UART_UACR, quot1[2]);
+#else
 	serial_dl_write(up, quot);
+#endif
 
 	/*
 	 * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR
diff -ru linux-2.6/drivers/usb/core/hub.c /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/core/hub.c
--- linux-2.6/drivers/usb/core/hub.c	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/core/hub.c	2009-08-12 10:39:09.000000000 +0200
@@ -1749,6 +1749,25 @@
 {
 	int i, status;
 
+#ifdef CONFIG_SOC_JZ4730
+	/*
+	 * On Jz4730, we assume that the first USB port was used as device.
+	 * If not, please comment next lines.
+	 */
+	if (port1 == 1) {
+		return 0;
+	}
+#endif
+
+#if defined(CONFIG_SOC_JZ4740) || defined(CONFIG_SOC_JZ4750) || defined(CONFIG_SOC_JZ4750D)
+	/*
+	 * On Jz4740 and Jz4750, the second USB port was used as device.
+	 */
+	if (port1 == 2) {
+		return 0;
+	}
+#endif
+
 	/* Block EHCI CF initialization during the port reset.
 	 * Some companion controllers don't like it when they mix.
 	 */
@@ -2666,11 +2685,35 @@
 			le16_to_cpu(hub->descriptor->wHubCharacteristics);
 	struct usb_device *udev;
 	int status, i;
+#ifdef CONFIG_JZSOC
+	static char jzhub = 1; /* the hub first to be initialized is jzsoc on-chip hub */
+#endif
 
 	dev_dbg (hub_dev,
 		"port %d, status %04x, change %04x, %s\n",
 		port1, portstatus, portchange, portspeed (portstatus));
 
+#ifdef CONFIG_SOC_JZ4730
+	/*
+	 * On Jz4730, we assume that the first USB port was used as device.
+	 * If not, please comment next lines.
+	 */
+	if ((port1 == 1) && (jzhub)) {
+		jzhub = 0;
+		return;
+	}
+#endif
+
+#if defined(CONFIG_SOC_JZ4740) || defined(CONFIG_SOC_JZ4750) || defined(CONFIG_SOC_JZ4750D)
+	/*
+	 * On Jz4740 and Jz4750, the second USB port was used as device.
+	 */
+	if ((port1 == 2) && (jzhub)) {
+		jzhub = 0;
+		return;
+	}
+#endif
+
 	if (hub->has_indicators) {
 		set_port_led(hub, port1, HUB_LED_AUTO);
 		hub->indicator[port1-1] = INDICATOR_AUTO;
diff -ru linux-2.6/drivers/usb/gadget/composite.c /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/gadget/composite.c
--- linux-2.6/drivers/usb/gadget/composite.c	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/gadget/composite.c	2009-08-12 10:39:09.000000000 +0200
@@ -492,7 +492,8 @@
 
 	while (*sp) {
 		s = *sp++;
-		if (s->language != language)
+		
+		if (language && s->language != language)
 			continue;
 		value = usb_gadget_get_string(s, id, buf);
 		if (value > 0)
@@ -612,8 +613,8 @@
  * housekeeping for the gadget function we're implementing.  Most of
  * the work is in config and function specific setup.
  */
-static int
-composite_setup(struct usb_gadget *gadget, const struct usb_ctrlrequest *ctrl)
+
+int composite_setup(struct usb_gadget *gadget, const struct usb_ctrlrequest *ctrl)
 {
 	struct usb_composite_dev	*cdev = get_gadget_data(gadget);
 	struct usb_request		*req = cdev->req;
@@ -984,7 +985,7 @@
 	.speed		= USB_SPEED_HIGH,
 
 	.bind		= composite_bind,
-	.unbind		= __exit_p(composite_unbind),
+	.unbind		= composite_unbind,
 
 	.setup		= composite_setup,
 	.disconnect	= composite_disconnect,
diff -ru linux-2.6/drivers/usb/gadget/file_storage.c /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/gadget/file_storage.c
--- linux-2.6/drivers/usb/gadget/file_storage.c	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/gadget/file_storage.c	2009-08-12 10:39:09.000000000 +0200
@@ -274,6 +274,18 @@
 
 
 /*-------------------------------------------------------------------------*/
+#if defined(CONFIG_UDC_USE_LB_CACHE)
+#define GHOST
+#endif
+
+#ifdef GHOST
+extern unsigned long udc_read(unsigned int offset, unsigned int len, unsigned char *);
+extern unsigned long udc_write(unsigned int offset, unsigned int len, unsigned char *);
+extern int NAND_LB_Init(void);
+extern int NAND_LB_FLASHCACHE(void);
+extern int NAND_MTD_FLASHCACHE(void);
+extern int FlushDataState;
+#endif
 
 #define LDBG(lun,fmt,args...) \
 	dev_dbg(&(lun)->dev , fmt , ## args)
@@ -345,8 +357,8 @@
 } mod_data = {					// Default values
 	.transport_parm		= "BBB",
 	.protocol_parm		= "SCSI",
-	.removable		= 0,
-	.can_stall		= 1,
+	.removable		= 1,
+	.can_stall		= 0,
 	.vendor			= DRIVER_VENDOR_ID,
 	.product		= DRIVER_PRODUCT_ID,
 	.release		= 0xffff,	// Use controller chip type
@@ -806,6 +818,7 @@
 #define STRING_SERIAL		3
 #define STRING_CONFIG		4
 #define STRING_INTERFACE	5
+#define STRING_MS_OS		0xee
 
 /* There is only one configuration. */
 #define	CONFIG_VALUE		1
@@ -993,6 +1006,7 @@
 	{STRING_SERIAL,		serial},
 	{STRING_CONFIG,		"Self-powered"},
 	{STRING_INTERFACE,	"Mass Storage"},
+	{STRING_MS_OS,		"Microsoft"},
 	{}
 };
 
@@ -1614,9 +1628,13 @@
 
 		/* Perform the read */
 		file_offset_tmp = file_offset;
+#ifdef GHOST
+		nread = udc_read(file_offset_tmp, amount, bh->buf);
+#else
 		nread = vfs_read(curlun->filp,
 				(char __user *) bh->buf,
 				amount, &file_offset_tmp);
+#endif
 		VLDBG(curlun, "file read %u @ %llu -> %d\n", amount,
 				(unsigned long long) file_offset,
 				(int) nread);
@@ -1795,9 +1813,13 @@
 
 			/* Perform the write */
 			file_offset_tmp = file_offset;
+#ifdef GHOST
+			nwritten = udc_write(file_offset_tmp, amount, bh->buf);
+#else
 			nwritten = vfs_write(curlun->filp,
 					(char __user *) bh->buf,
 					amount, &file_offset_tmp);
+#endif
 			VLDBG(curlun, "file write %u @ %llu -> %d\n", amount,
 					(unsigned long long) file_offset,
 					(int) nwritten);
@@ -1972,9 +1994,13 @@
 
 		/* Perform the read */
 		file_offset_tmp = file_offset;
+#ifdef GHOST
+		nread = udc_read(file_offset_tmp, amount, bh->buf);
+#else
 		nread = vfs_read(curlun->filp,
 				(char __user *) bh->buf,
 				amount, &file_offset_tmp);
+#endif
 		VLDBG(curlun, "file read %u @ %llu -> %d\n", amount,
 				(unsigned long long) file_offset,
 				(int) nread);
@@ -2009,7 +2035,7 @@
 {
 	u8	*buf = (u8 *) bh->buf;
 
-	static char vendor_id[] = "Linux   ";
+	static char vendor_id[] = "Ingenic  ";
 	static char product_id[] = "File-Stor Gadget";
 
 	if (!fsg->curlun) {		// Unsupported LUNs are okay
@@ -2876,6 +2902,15 @@
 		reply = check_command(fsg, 6, DATA_DIR_NONE,
 				0, 1,
 				"TEST UNIT READY");
+#ifdef GHOST
+		if( FlushDataState >= 1)
+			FlushDataState++;
+		if(FlushDataState > 6)
+		{	
+			NAND_LB_FLASHCACHE();
+			FlushDataState = 0;
+		}
+#endif
 		break;
 
 	/* Although optional, this command is used by MS-Windows.  We
@@ -3425,6 +3460,13 @@
 
 	/* The main loop */
 	while (fsg->state != FSG_STATE_TERMINATED) {
+#ifdef GHOST
+		if ((fsg->atomic_bitflags & SUSPENDED))
+		{
+			NAND_LB_FLASHCACHE();
+			NAND_MTD_FLASHCACHE();
+		}
+#endif
 		if (exception_in_progress(fsg) || signal_pending(current)) {
 			handle_exception(fsg);
 			continue;
@@ -3547,6 +3589,10 @@
 	LDBG(curlun, "open backing file: %s\n", filename);
 	rc = 0;
 
+#ifdef GHOST
+	NAND_LB_Init(); 
+#endif
+
 out:
 	filp_close(filp, current->files);
 	return rc;
diff -ru linux-2.6/drivers/usb/gadget/gadget_chips.h /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/gadget/gadget_chips.h
--- linux-2.6/drivers/usb/gadget/gadget_chips.h	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/gadget/gadget_chips.h	2009-08-12 10:39:09.000000000 +0200
@@ -15,6 +15,24 @@
 #ifndef __GADGET_CHIPS_H
 #define __GADGET_CHIPS_H
 
+#ifdef CONFIG_USB_GADGET_JZ4750
+#define	gadget_is_jz4750(g)	!strcmp("ingenic_hsusb", (g)->name) /* same driver */
+#else
+#define	gadget_is_jz4750(g)	0
+#endif
+
+#ifdef CONFIG_USB_GADGET_JZ4740
+#define	gadget_is_jz4740(g)	!strcmp("ingenic_hsusb", (g)->name)
+#else
+#define	gadget_is_jz4740(g)	0
+#endif
+
+#ifdef CONFIG_USB_GADGET_JZ4730
+#define	gadget_is_jz4730(g)	!strcmp("jz4730_udc", (g)->name)
+#else
+#define	gadget_is_jz4730(g)	0
+#endif
+
 #ifdef CONFIG_USB_GADGET_NET2280
 #define	gadget_is_net2280(g)	!strcmp("net2280", (g)->name)
 #else
@@ -216,6 +234,13 @@
 		return 0x20;
 	else if (gadget_is_m66592(gadget))
 		return 0x21;
+	else if (gadget_is_jz4730(gadget))
+		return 0x22;
+	else if (gadget_is_jz4740(gadget))
+		return 0x23;
+	else if (gadget_is_jz4750(gadget))
+		return 0x24;
+
 	return -ENOENT;
 }
 
diff -ru linux-2.6/drivers/usb/gadget/Kconfig /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/gadget/Kconfig
--- linux-2.6/drivers/usb/gadget/Kconfig	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/gadget/Kconfig	2009-08-12 10:39:09.000000000 +0200
@@ -94,6 +94,47 @@
 	   Many controller drivers are platform-specific; these
 	   often need board-specific hooks.
 
+config USB_GADGET_JZ4740
+	boolean "JZ4740 UDC"
+	depends on SOC_JZ4740
+	select USB_GADGET_DUALSPEED
+	help
+    	   Select this to support the Ingenic JZ4740 processor 
+           high speed USB device controller.
+
+config USB_JZ4740
+	tristate
+	depends on USB_GADGET_JZ4740
+	default USB_GADGET
+	select USB_GADGET_SELECTED
+
+config USB_GADGET_JZ4750
+	boolean "JZ4750 UDC"
+	depends on SOC_JZ4750 || SOC_JZ4750D
+	select USB_GADGET_DUALSPEED
+	help
+    	   Select this to support the Ingenic JZ4750 processor 
+           high speed USB device controller.
+
+config USB_JZ4750
+	tristate
+	depends on USB_GADGET_JZ4750
+	default USB_GADGET
+	select USB_GADGET_SELECTED
+
+config USB_GADGET_JZ4730
+	boolean "JZ4730 UDC"
+	depends on SOC_JZ4730
+	help
+    	   Select this to support the Ingenic JZ4730 processor 
+           full speed USB device controller.
+
+config USB_JZ4730
+	tristate
+	depends on USB_GADGET_JZ4730
+	default USB_GADGET
+	select USB_GADGET_SELECTED
+
 config USB_GADGET_AMD5536UDC
 	boolean "AMD5536 UDC"
 	depends on PCI
@@ -399,6 +440,18 @@
 
 endchoice
 
+config USB_JZ_UDC_HOTPLUG
+	boolean "Ingenic USB Device Controller Hotplug Support"
+	depends on USB_GADGET_JZ4750
+
+config UDC_USE_LB_CACHE
+	bool "NAND LB Cache Support"
+	depends on (USB_FILE_STORAGE || USB_ANDROID) && (SOC_JZ4740 || SOC_JZ4750 || SOC_JZ4750D)
+	default y
+	help
+	  say "y" to enable lb cache and UDC work in faster speed.
+	  say "n" to disable lb cache and UDC work in normal speed.
+
 config USB_GADGET_DUALSPEED
 	bool
 	depends on USB_GADGET
@@ -406,7 +459,6 @@
 	help
 	  Means that gadget drivers should include extra descriptors
 	  and code to handle dual-speed controllers.
-
 #
 # USB Gadget Drivers
 #
@@ -596,6 +648,16 @@
 	  For more information, see Documentation/usb/gadget_printer.txt
 	  which includes sample code for accessing the device file.
 
+config USB_ANDROID
+	tristate "Android Gadget"
+	select USB_JZ_UDC_HOTPLUG
+
+	help
+	  The Android gadget provides mass storage and adb transport.
+
+	  Say "y" to link the driver statically, or "m" to build a
+	  dynamically linked module called "g_android".
+
 config USB_CDC_COMPOSITE
 	tristate "CDC Composite Device (Ethernet and ACM)"
 	depends on NET
diff -ru linux-2.6/drivers/usb/gadget/Makefile /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/gadget/Makefile
--- linux-2.6/drivers/usb/gadget/Makefile	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/gadget/Makefile	2009-08-12 10:39:09.000000000 +0200
@@ -18,6 +18,11 @@
 obj-$(CONFIG_USB_ATMEL_USBA)	+= atmel_usba_udc.o
 obj-$(CONFIG_USB_FSL_USB2)	+= fsl_usb2_udc.o
 obj-$(CONFIG_USB_M66592)	+= m66592-udc.o
+obj-$(CONFIG_USB_JZ4740)	+= jz4740_udc.o
+obj-$(CONFIG_USB_JZ4730)	+= jz4730_udc.o
+obj-$(CONFIG_USB_JZ4750)	+= jz4740_udc.o
+
+obj-$(CONFIG_USB_JZ_UDC_HOTPLUG)+= udc_hotplug_core.o
 
 #
 # USB gadget drivers
@@ -35,6 +40,7 @@
 					epautoconf.o
 g_cdc-objs			:= cdc2.o u_ether.o f_ecm.o \
 					u_serial.o f_acm.o $(C_UTILS)
+g_android-objs			:= android.o f_adb.o f_mass_storage.o $(C_UTILS)
 
 ifeq ($(CONFIG_USB_ETH_RNDIS),y)
 	g_ether-objs		+= f_rndis.o rndis.o
@@ -48,4 +54,5 @@
 obj-$(CONFIG_USB_G_PRINTER)	+= g_printer.o
 obj-$(CONFIG_USB_MIDI_GADGET)	+= g_midi.o
 obj-$(CONFIG_USB_CDC_COMPOSITE) += g_cdc.o
+obj-$(CONFIG_USB_ANDROID)	+= g_android.o
 
diff -ru linux-2.6/drivers/usb/host/ohci-hcd.c /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/host/ohci-hcd.c
--- linux-2.6/drivers/usb/host/ohci-hcd.c	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/host/ohci-hcd.c	2009-08-12 10:39:09.000000000 +0200
@@ -995,6 +995,11 @@
 #define PCI_DRIVER		ohci_pci_driver
 #endif
 
+#ifdef CONFIG_JZSOC
+#include "ohci-jz.c"
+#define PLATFORM_DRIVER		ohci_hcd_jz_driver
+#endif
+
 #if defined(CONFIG_ARCH_SA1100) && defined(CONFIG_SA1111)
 #include "ohci-sa1111.c"
 #define SA1111_DRIVER		ohci_hcd_sa1111_driver
diff -ru linux-2.6/drivers/usb/Kconfig /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/Kconfig
--- linux-2.6/drivers/usb/Kconfig	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/Kconfig	2009-08-12 10:39:09.000000000 +0200
@@ -42,6 +42,7 @@
 	default y if PPC_MPC52xx
 	# MIPS:
 	default y if SOC_AU1X00
+	default y if JZSOC
 	# SH:
 	default y if CPU_SUBTYPE_SH7720
 	default y if CPU_SUBTYPE_SH7721
diff -ru linux-2.6/drivers/usb/musb/Kconfig /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/musb/Kconfig
--- linux-2.6/drivers/usb/musb/Kconfig	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/musb/Kconfig	2009-08-12 10:39:09.000000000 +0200
@@ -8,7 +8,10 @@
 
 # (M)HDRC = (Multipoint) Highspeed Dual-Role Controller
 config USB_MUSB_HDRC
-	depends on (USB || USB_GADGET) && HAVE_CLK
+	depends on (USB || USB_GADGET) 
+
+#&& HAVE_CLK Disabled by River
+
 	depends on !SUPERH
 	select TWL4030_USB if MACH_OMAP_3430SDP
 	tristate 'Inventra Highspeed Dual Role Controller (TI, ...)'
@@ -144,12 +147,17 @@
 	  parameter.
 
 config USB_INVENTRA_DMA
-	bool
+	bool 'Use INVENTRA DMA'
 	depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY
-	default ARCH_OMAP2430 || ARCH_OMAP34XX
+	default ARCH_OMAP2430 || ARCH_OMAP34XX || SOC_JZ4760
 	help
 	  Enable DMA transfers using Mentor's engine.
 
+config USB_MUSB_HSDMA_IRQ_SHARED
+	bool 'INVENTRA DMA IRQ shared with USB IRQ'
+	depends on USB_MUSB_HDRC && USB_INVENTRA_DMA && !MUSB_PIO_ONLY
+	default SOC_JZ4760
+
 config USB_TI_CPPI_DMA
 	bool
 	depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY
diff -ru linux-2.6/drivers/usb/musb/Makefile /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/musb/Makefile
--- linux-2.6/drivers/usb/musb/Makefile	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/musb/Makefile	2009-08-12 10:39:09.000000000 +0200
@@ -22,6 +22,10 @@
 	musb_hdrc-objs	+= omap2430.o
 endif
 
+ifeq ($(CONFIG_SOC_JZ4760),y)
+	musb_hdrc-objs	+= jz4760.o
+endif
+
 ifeq ($(CONFIG_USB_GADGET_MUSB_HDRC),y)
 	musb_hdrc-objs		+= musb_gadget_ep0.o musb_gadget.o
 endif
diff -ru linux-2.6/drivers/usb/musb/musb_core.c /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/musb/musb_core.c
--- linux-2.6/drivers/usb/musb/musb_core.c	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/musb/musb_core.c	2009-08-12 10:39:09.000000000 +0200
@@ -107,13 +107,10 @@
 
 #include "musb_core.h"
 
-
 #ifdef CONFIG_ARCH_DAVINCI
 #include "davinci.h"
 #endif
 
-
-
 unsigned debug;
 module_param(debug, uint, S_IRUGO | S_IWUSR);
 MODULE_PARM_DESC(debug, "Debug message level. Default = 0");
@@ -148,6 +145,34 @@
 
 /*-------------------------------------------------------------------------*/
 
+static inline void musb_dump_packet(int epnum, const u8 *packet, u16 len)
+{
+	u16 i;
+	
+#ifdef MUSB_DUMP_EP_NUM
+	if (epnum != MUSB_DUMP_EP_NUM)
+		return;
+#endif
+
+	printk(KERN_ERR "\nMUSB Packet Dump: Length: %d bytes.\n", len);
+	printk(KERN_ERR "==============================================\n");
+	
+	for (i = 0; i < len; i++) {
+		printk("0x%02x ", packet[i]);
+		if ((i+ 1) % 10 == 0) 
+			printk("\n");
+	}
+	
+	printk("\n");
+	printk(KERN_ERR "==============================================\n");
+}
+
+#define MUSB_DUMP_TX_PACKET(epnum, packet, len)	\
+//	musb_dump_packet(epnum, packet, len)
+
+#define MUSB_DUMP_RX_PACKET(epnum, packet, len)	\
+//	musb_dump_packet(epnum, packet, len)
+
 #ifndef CONFIG_USB_TUSB6010
 /*
  * Load an endpoint's FIFO
@@ -187,6 +212,8 @@
 		/* byte aligned */
 		writesb(fifo, src, len);
 	}
+	
+	MUSB_DUMP_TX_PACKET(hw_ep->num, src, len);
 }
 
 /*
@@ -225,6 +252,8 @@
 		/* byte aligned */
 		readsb(fifo, dst, len);
 	}
+	
+	MUSB_DUMP_RX_PACKET(hw_ep->epnum, dst, len);
 }
 
 #endif	/* normal PIO */
@@ -477,6 +506,20 @@
 
 #ifdef CONFIG_USB_MUSB_HDRC_HCD
 	/* see manual for the order of the tests */
+
+#ifdef CONFIG_SOC_JZ4760
+	/*
+	 * Modified by River
+	 * Note: There is a strange Session request IRQ asserted in the MUSB IP core of JZ4760 when MUSB is operating in DEVICE mode.
+	 * We just ignore it.
+	 */
+
+	if ((int_usb & MUSB_INTR_SESSREQ) && !(devctl & MUSB_DEVCTL_HM)) {
+		DBG(1, "SESSION_REQUEST (%s)\n", otg_state_string(musb));
+
+		handled = IRQ_HANDLED;
+	}
+#else
 	if (int_usb & MUSB_INTR_SESSREQ) {
 		DBG(1, "SESSION_REQUEST (%s)\n", otg_state_string(musb));
 
@@ -495,6 +538,7 @@
 
 		handled = IRQ_HANDLED;
 	}
+#endif
 
 	if (int_usb & MUSB_INTR_VBUSERROR) {
 		int	ignore = 0;
@@ -766,6 +810,7 @@
 #ifdef CONFIG_USB_MUSB_HDRC_HCD
 		case OTG_STATE_A_HOST:
 		case OTG_STATE_A_SUSPEND:
+			usb_hcd_resume_root_hub(musb_to_hcd(musb)); /* River - from Linux-2.6.29-rc6 usb-musb-resume-suspend-root-hub-on-disconnect.patch */
 			musb_root_disconnect(musb);
 			if (musb->a_wait_bcon != 0)
 				musb_platform_try_idle(musb, jiffies
@@ -959,10 +1004,13 @@
 	spin_lock_irqsave(&musb->lock, flags);
 	musb_platform_disable(musb);
 	musb_generic_disable(musb);
+
+#ifdef CONFIG_HAVE_CLK
 	if (musb->clock) {
 		clk_put(musb->clock);
 		musb->clock = NULL;
 	}
+#endif	
 	spin_unlock_irqrestore(&musb->lock, flags);
 
 	/* FIXME power down */
@@ -1259,7 +1307,7 @@
 		hw_ep = musb->endpoints + epnum;
 
 		/* read from core using indexed model */
-		reg = musb_readb(hw_ep->regs, 0x10 + MUSB_FIFOSIZE);
+		reg = musb_readb(mbase, 0x10 + MUSB_FIFOSIZE); /* Do not use hw_ep->regs before it's initialized. - Fixed by River. */
 		if (!reg) {
 			/* 0's returned when no more endpoints */
 			break;
@@ -1402,6 +1450,9 @@
 	/* configure ep0 */
 	musb->endpoints[0].max_packet_sz_tx = MUSB_EP0_FIFOSIZE;
 	musb->endpoints[0].max_packet_sz_rx = MUSB_EP0_FIFOSIZE;
+	
+	/* Added by River */
+	musb->endpoints[0].is_shared_fifo = 1;
 
 	/* discover endpoint configuration */
 	musb->nr_endpoints = 1;
@@ -1477,8 +1528,48 @@
 
 /*-------------------------------------------------------------------------*/
 
-#if defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3430)
+#if defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3430) || defined(CONFIG_SOC_JZ4760) /* Added by River */
+
+/* Modified by River - For DMA IRQ Sharing */
+#if defined(CONFIG_USB_MUSB_HSDMA_IRQ_SHARED)
+static irqreturn_t generic_interrupt(int irq, void *__hci)
+{
+	unsigned long	flags;
+	struct musb	*musb = __hci;
+	
+	irqreturn_t	rv, rv_dma, rv_usb;
+	
+	rv = rv_dma = rv_usb = IRQ_NONE;
+
+	spin_lock_irqsave(&musb->lock, flags);
+	
+	/* Process DMA IRQ. */
+	if (dma_controller_fetch_intr(musb->dma_controller))
+		rv_dma = dma_controller_irq(irq, (void *)musb);
+	
+	musb->int_usb = musb_readb(musb->mregs, MUSB_INTRUSB);
+	musb->int_tx = musb_readw(musb->mregs, MUSB_INTRTX);
+	musb->int_rx = musb_readw(musb->mregs, MUSB_INTRRX);
+
+	if (musb->int_usb || musb->int_tx || musb->int_rx)
+		rv_usb = musb_interrupt(musb);
+
+	spin_unlock_irqrestore(&musb->lock, flags);
+
+	/* REVISIT we sometimes get spurious IRQs on g_ep0
+	 * not clear why...
+	 */
+
+	rv = (rv_dma == IRQ_HANDLED || rv_usb == IRQ_HANDLED) ? IRQ_HANDLED : IRQ_NONE;
 
+	if (rv != IRQ_HANDLED)
+		DBG(5, "spurious?\n");
+
+	return IRQ_HANDLED;
+}
+
+#else /* !CONFIG_USB_MUSB_HSDMA_IRQ_SHARED */
+/* Original IRQ Handler */
 static irqreturn_t generic_interrupt(int irq, void *__hci)
 {
 	unsigned long	flags;
@@ -1504,6 +1595,7 @@
 
 	return IRQ_HANDLED;
 }
+#endif /* Defined CONFIG_USB_MUSB_HSDMA_IRQ_SHARED - End added */
 
 #else
 #define generic_interrupt	NULL
@@ -1525,11 +1617,14 @@
 
 	devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
 	power = musb_readb(musb->mregs, MUSB_POWER);
+	
+	D("DEVCTL: 0x%x, POWER: 0x%x.\n", devctl, power);
+	D("musb->int_usb: 0x%x, musb->int_tx: 0x%x, musb->int_rx: 0x%x.\n", musb->int_usb, musb->int_tx, musb->int_rx);
 
 	DBG(4, "** IRQ %s usb%04x tx%04x rx%04x\n",
 		(devctl & MUSB_DEVCTL_HM) ? "host" : "peripheral",
 		musb->int_usb, musb->int_tx, musb->int_rx);
-
+	
 	/* the core can interrupt us for multiple reasons; docs have
 	 * a generic interrupt flowchart to follow
 	 */
@@ -1652,6 +1747,30 @@
 #ifdef CONFIG_SYSFS
 
 static ssize_t
+musb_devctl_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct musb *musb = dev_to_musb(dev);
+	unsigned long flags;
+	int ret = -EINVAL;
+
+
+	spin_lock_irqsave(&musb->lock, flags);
+	ret = sprintf(buf, "0x%x\n", musb_readb(musb->mregs, MUSB_DEVCTL));
+	spin_unlock_irqrestore(&musb->lock, flags);
+
+	return ret;
+}
+
+static ssize_t
+musb_devctl_store(struct device *dev, struct device_attribute *attr,
+		const char *buf, size_t n)
+{
+	return n;
+}
+static DEVICE_ATTR(devctl, 0644, musb_devctl_show, musb_devctl_store);
+
+
+static ssize_t
 musb_mode_show(struct device *dev, struct device_attribute *attr, char *buf)
 {
 	struct musb *musb = dev_to_musb(dev);
@@ -1826,6 +1945,7 @@
 	 */
 
 #ifdef CONFIG_SYSFS
+	device_remove_file(musb->controller, &dev_attr_devctl);
 	device_remove_file(musb->controller, &dev_attr_mode);
 	device_remove_file(musb->controller, &dev_attr_vbus);
 #ifdef CONFIG_USB_MUSB_OTG
@@ -1838,9 +1958,12 @@
 #endif
 
 	if (musb->nIrq >= 0) {
-		disable_irq_wake(musb->nIrq);
+		if (musb->b_irq_wake) /* Fixed by River. - Don't call disable_irq_wake() when set_irq_wake() fails. */
+			disable_irq_wake(musb->nIrq);
+	
 		free_irq(musb->nIrq, musb);
 	}
+
 	if (is_dma_capable() && musb->dma_controller) {
 		struct dma_controller	*c = musb->dma_controller;
 
@@ -1852,10 +1975,12 @@
 	musb_platform_exit(musb);
 	musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
 
+#ifdef CONFIG_HAVE_CLK /* Added by River */	
 	if (musb->clock) {
 		clk_disable(musb->clock);
 		clk_put(musb->clock);
 	}
+#endif
 
 #ifdef CONFIG_USB_MUSB_OTG
 	put_device(musb->xceiv.dev);
@@ -1922,9 +2047,13 @@
 	spin_lock_init(&musb->lock);
 	musb->board_mode = plat->mode;
 	musb->board_set_power = plat->set_power;
+
+#ifdef CONFIG_HAVE_CLK /* Added by River */
 	musb->set_clock = plat->set_clock;
+#endif
 	musb->min_power = plat->min_power;
 
+#ifdef CONFIG_HAVE_CLK /* Added by River */
 	/* Clock usage is chip-specific ... functional clock (DaVinci,
 	 * OMAP2430), or PHY ref (some TUSB6010 boards).  All this core
 	 * code does is make sure a clock handle is available; platform
@@ -1938,6 +2067,7 @@
 			goto fail;
 		}
 	}
+#endif
 
 	/* assume vbus is off */
 
@@ -1990,8 +2120,10 @@
 	}
 	musb->nIrq = nIrq;
 /* FIXME this handles wakeup irqs wrong */
-	if (enable_irq_wake(nIrq) == 0)
+	if (enable_irq_wake(nIrq) == 0) { /* Fixe by River. */
 		device_init_wakeup(dev, 1);
+		musb->b_irq_wake = 1;
+	}
 
 	pr_info("%s: USB %s mode controller at %p using %s, IRQ %d\n",
 			musb_driver_name,
@@ -2057,13 +2189,18 @@
 	return 0;
 
 fail:
+
+#ifdef CONFIG_HAVE_CLK	
 	if (musb->clock)
 		clk_put(musb->clock);
+#endif
+
 	device_init_wakeup(dev, 0);
 	musb_free(musb);
 	return status;
 
 #ifdef CONFIG_SYSFS
+	status = device_create_file(dev, &dev_attr_devctl);
 	status = device_create_file(dev, &dev_attr_mode);
 	status = device_create_file(dev, &dev_attr_vbus);
 #ifdef CONFIG_USB_GADGET_MUSB_HDRC
@@ -2144,8 +2281,10 @@
 	unsigned long	flags;
 	struct musb	*musb = dev_to_musb(&pdev->dev);
 
+#ifdef CONFIG_HAVE_CLK
 	if (!musb->clock)
 		return 0;
+#endif
 
 	spin_lock_irqsave(&musb->lock, flags);
 
@@ -2159,10 +2298,13 @@
 		 */
 	}
 
+#ifdef CONFIG_HAVE_CLK
 	if (musb->set_clock)
 		musb->set_clock(musb->clock, 0);
 	else
 		clk_disable(musb->clock);
+#endif
+
 	spin_unlock_irqrestore(&musb->lock, flags);
 	return 0;
 }
@@ -2172,15 +2314,18 @@
 	unsigned long	flags;
 	struct musb	*musb = dev_to_musb(&pdev->dev);
 
+#ifdef CONFIG_HAVE_CLK	
 	if (!musb->clock)
 		return 0;
-
+#endif
 	spin_lock_irqsave(&musb->lock, flags);
 
+#ifdef CONFIG_HAVE_CLK
 	if (musb->set_clock)
 		musb->set_clock(musb->clock, 1);
 	else
 		clk_enable(musb->clock);
+#endif
 
 	/* for static cmos like DaVinci, register values were preserved
 	 * unless for some reason the whole soc powered down and we're
diff -ru linux-2.6/drivers/usb/musb/musb_core.h /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/musb/musb_core.h
--- linux-2.6/drivers/usb/musb/musb_core.h	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/musb/musb_core.h	2009-08-12 10:39:09.000000000 +0200
@@ -52,7 +52,6 @@
 struct musb_hw_ep;
 struct musb_ep;
 
-
 #include "musb_debug.h"
 #include "musb_dma.h"
 
@@ -63,7 +62,8 @@
 #include "../core/hcd.h"
 #include "musb_host.h"
 
-
+#define D(fmt, args...) \
+//	printk(KERN_ERR "%s(): LINE: %d "fmt, __func__, __LINE__, ##args)
 
 #ifdef CONFIG_USB_MUSB_OTG
 
@@ -306,7 +306,10 @@
 struct musb {
 	/* device lock */
 	spinlock_t		lock;
+
+#ifdef CONFIG_HAVE_CLK /* Added by River */
 	struct clk		*clock;
+#endif
 	irqreturn_t		(*isr)(int, void *);
 	struct work_struct	irq_work;
 
@@ -359,7 +362,8 @@
 	struct otg_transceiver	xceiv;
 
 	int nIrq;
-
+	u8 			b_irq_wake; /* Added by River. */
+	
 	struct musb_hw_ep	 endpoints[MUSB_C_NUM_EPS];
 #define control_ep		endpoints
 
@@ -371,8 +375,9 @@
 	u8 board_mode;		/* enum musb_mode */
 	int			(*board_set_power)(int state);
 
+#ifdef CONFIG_HAVE_CLK /* Added by River */
 	int			(*set_clock)(struct clk *clk, int is_active);
-
+#endif
 	u8			min_power;	/* vbus for periph, in mA/2 */
 
 	bool			is_host;
diff -ru linux-2.6/drivers/usb/musb/musb_dma.h /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/musb/musb_dma.h
--- linux-2.6/drivers/usb/musb/musb_dma.h	2009-08-17 23:57:37.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/musb/musb_dma.h	2009-08-12 10:39:09.000000000 +0200
@@ -148,6 +148,13 @@
  * Controllers manage dma channels.
  */
 struct dma_controller {
+
+/* Added by River - For DMA IRQ Sharing */
+#ifdef  CONFIG_USB_MUSB_HSDMA_IRQ_SHARED
+	u8			int_hsdma;	/* MUSB_HSDMA_INTR */
+#endif
+/* End added */	
+
 	int			(*start)(struct dma_controller *);
 	int			(*stop)(struct dma_controller *);
 	struct dma_channel	*(*channel_alloc)(struct dma_controller *,
@@ -163,10 +170,18 @@
 /* called after channel_program(), may indicate a fault */
 extern void musb_dma_completion(struct musb *musb, u8 epnum, u8 transmit);
 
-
 extern struct dma_controller *__init
 dma_controller_create(struct musb *, void __iomem *);
 
 extern void dma_controller_destroy(struct dma_controller *);
 
+/* Added by River - For DMA IRQ Sharing */
+#ifdef CONFIG_USB_MUSB_HSDMA_IRQ_SHARED
+extern u8 dma_controller_fetch_intr(struct dma_controller *c);
+
+irqreturn_t dma_controller_irq(int irq, void *private_data);
+
+#endif /* End added */
+
 #endif	/* __MUSB_DMA_H__ */
+
diff -ru linux-2.6/drivers/usb/musb/musb_gadget_ep0.c /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/musb/musb_gadget_ep0.c
--- linux-2.6/drivers/usb/musb/musb_gadget_ep0.c	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/musb/musb_gadget_ep0.c	2009-08-12 10:39:09.000000000 +0200
@@ -405,7 +405,8 @@
 					csr |= MUSB_RXCSR_P_SENDSTALL
 						| MUSB_RXCSR_FLUSHFIFO
 						| MUSB_RXCSR_CLRDATATOG
-						| MUSB_TXCSR_P_WZC_BITS;
+//						| MUSB_TXCSR_P_WZC_BITS;
+						| MUSB_RXCSR_P_WZC_BITS; /* Corrected by River. */
 					musb_writew(regs, MUSB_RXCSR,
 							csr);
 				}
diff -ru linux-2.6/drivers/usb/musb/musb_host.c /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/musb/musb_host.c
--- linux-2.6/drivers/usb/musb/musb_host.c	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/musb/musb_host.c	2009-08-12 10:39:09.000000000 +0200
@@ -40,10 +40,16 @@
 #include <linux/errno.h>
 #include <linux/init.h>
 #include <linux/list.h>
+#include <linux/autoconf.h>
 
 #include "musb_core.h"
 #include "musb_host.h"
 
+/* Added by River. */
+/* The MUSBHDRC core RTL V1.8 in JZ4760 has no data toogle control. */
+#ifndef CONFIG_SOC_JZ4760
+#define HAVE_DATA_TOGGLE_CONTROL	1
+#endif
 
 /* MUSB HOST status 22-mar-2006
  *
@@ -296,9 +302,10 @@
 	spin_lock(&musb->lock);
 }
 
+/* Modified by River. */
+#ifdef HAVE_DATA_TOGGLE_CONTROL
 /* for bulk/interrupt endpoints only */
-static inline void
-musb_save_toggle(struct musb_hw_ep *ep, int is_in, struct urb *urb)
+static inline void musb_save_toggle(struct musb_hw_ep *ep, int is_in, struct urb *urb)
 {
 	struct usb_device	*udev = urb->dev;
 	u16			csr;
@@ -326,6 +333,12 @@
 				? 1 : 0);
 	}
 }
+#else /* !HAVE_DATA_TOGGLE_CONTROL */
+static inline void musb_save_toggle(struct musb_hw_ep *ep, int is_in, struct urb *urb)
+{
+	return;
+}
+#endif
 
 /* caller owns controller lock, irqs are blocked */
 static struct musb_qh *
@@ -563,7 +576,7 @@
 musb_rx_reinit(struct musb *musb, struct musb_qh *qh, struct musb_hw_ep *ep)
 {
 	u16	csr;
-
+	
 	/* NOTE:  we know the "rx" fifo reinit never triggers for ep0.
 	 * That always uses tx_reinit since ep0 repurposes TX register
 	 * offsets; the initial SETUP packet is also a kind of OUT.
@@ -586,8 +599,12 @@
 		if (csr & MUSB_RXCSR_RXPKTRDY)
 			WARNING("rx%d, packet/%d ready?\n", ep->epnum,
 				musb_readw(ep->regs, MUSB_RXCOUNT));
-
+/* Modified by River. */
+#ifdef HAVE_DATA_TOGGLE_CONTROL
 		musb_h_flush_rxfifo(ep, MUSB_RXCSR_CLRDATATOG);
+#else
+		musb_h_flush_rxfifo(ep, 0);
+#endif
 	}
 
 	/* target addr and (for multipoint) hub addr/port */
@@ -688,13 +705,15 @@
 					| MUSB_TXCSR_TXPKTRDY
 					);
 			csr |= MUSB_TXCSR_MODE;
-
+/* Modified by River. */
+#ifdef HAVE_DATA_TOGGLE_CONTROL
 			if (usb_gettoggle(urb->dev,
 					qh->epnum, 1))
 				csr |= MUSB_TXCSR_H_WR_DATATOGGLE
 					| MUSB_TXCSR_H_DATATOGGLE;
 			else
 				csr |= MUSB_TXCSR_CLRDATATOG;
+#endif
 
 			/* twice in case of double packet buffering */
 			musb_writew(epio, MUSB_TXCSR, csr);
@@ -867,13 +886,18 @@
 
 		if (hw_ep->rx_reinit) {
 			musb_rx_reinit(musb, qh, hw_ep);
-
+/* Modified by River. */
+#ifdef HAVE_DATA_TOGGLE_CONTROL 
 			/* init new state: toggle and NYET, maybe DMA later */
-			if (usb_gettoggle(urb->dev, qh->epnum, 0))
+			if (usb_gettoggle(urb->dev, qh->epnum, 0)) {
 				csr = MUSB_RXCSR_H_WR_DATATOGGLE
 					| MUSB_RXCSR_H_DATATOGGLE;
-			else
+			}else{
 				csr = 0;
+			}
+#else
+			csr = 0;
+#endif
 			if (qh->type == USB_ENDPOINT_XFER_INT)
 				csr |= MUSB_RXCSR_DISNYET;
 
diff -ru linux-2.6/drivers/usb/musb/musbhsdma.c /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/musb/musbhsdma.c
--- linux-2.6/drivers/usb/musb/musbhsdma.c	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/musb/musbhsdma.c	2009-08-12 10:39:09.000000000 +0200
@@ -294,7 +294,11 @@
 	return 0;
 }
 
+#ifdef CONFIG_USB_MUSB_HSDMA_IRQ_SHARED
+irqreturn_t dma_controller_irq(int irq, void *private_data)
+#else
 static irqreturn_t dma_controller_irq(int irq, void *private_data)
+#endif	/* Defined CONFIG_USB_MUSB_HSDMA_IRQ_SHARED */
 {
 	struct musb_dma_controller *controller =
 		(struct musb_dma_controller *)private_data;
@@ -311,7 +315,14 @@
 
 	spin_lock_irqsave(&musb->lock, flags);
 
+	/* Added By River - For DMA IRQ Sharing */
+#ifdef CONFIG_USB_MUSB_HSDMA_IRQ_SHARED
+	int_hsdma = controller->Controller.int_hsdma;
+#else
 	int_hsdma = musb_readb(mbase, MUSB_HSDMA_INTR);
+#endif
+	/* End added */
+
 	if (!int_hsdma)
 		goto done;
 
@@ -419,15 +430,32 @@
 	controller->Controller.channel_release = dma_channel_release;
 	controller->Controller.channel_program = dma_channel_program;
 	controller->Controller.channel_abort = dma_channel_abort;
-
+	
+	/* Modified By River - For DMA IRQ Sharing */
+#ifdef CONFIG_USB_MUSB_HSDMA_IRQ_SHARED	
+	irq = 0;	/* Skip free_irq() when the controller will be removed. */
+#else	
 	if (request_irq(irq, dma_controller_irq, IRQF_DISABLED,
 			musb->controller->bus_id, &controller->Controller)) {
 		dev_err(dev, "request_irq %d failed!\n", irq);
 		dma_controller_destroy(&controller->Controller);
 		return NULL;
 	}
-
+#endif
+	/* End modified */
 	controller->irq = irq;
 
 	return &controller->Controller;
 }
+
+/* Added by river - For DMA IRQ Sharing */
+#ifdef CONFIG_USB_MUSB_HSDMA_IRQ_SHARED
+u8 dma_controller_fetch_intr(struct dma_controller *c)
+{
+	struct musb_dma_controller *mc = (struct musb_dma_controller *)c; /* See the defination... */
+
+	c->int_hsdma = musb_readb(mc->pCoreBase, MUSB_HSDMA_INTR);
+
+	return c->int_hsdma;
+}
+#endif
diff -ru linux-2.6/drivers/usb/musb/musb_io.h /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/musb/musb_io.h
--- linux-2.6/drivers/usb/musb/musb_io.h	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/usb/musb/musb_io.h	2009-08-12 10:39:09.000000000 +0200
@@ -37,7 +37,7 @@
 
 #include <linux/io.h>
 
-#ifndef	CONFIG_ARM
+#if !defined(CONFIG_ARM) && !defined(CONFIG_MIPS)
 static inline void readsl(const void __iomem *addr, void *buf, int len)
 	{ insl((unsigned long)addr, buf, len); }
 static inline void readsw(const void __iomem *addr, void *buf, int len)
diff -ru linux-2.6/drivers/video/Kconfig /plain/src/qi/linux-2.6.27.git.svn/drivers/video/Kconfig
--- linux-2.6/drivers/video/Kconfig	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/video/Kconfig	2009-08-12 10:39:09.000000000 +0200
@@ -234,6 +234,454 @@
 comment "Frame buffer hardware drivers"
 	depends on FB
 
+/************************************************************/
+
+config JZSOC_BOOT_LOGO
+	tristate "JZSOC boot up LOGO support"
+	depends on FB && JZSOC
+	---help---
+	If you select this function, you need put a logo file at ramdisk root directory,
+	whose name should be "/logo.rle" or "/logo.rgb565".
+
+choice
+	prompt "Boot LOGO File Format Select"
+	depends on JZSOC_BOOT_LOGO
+
+config FB_565RLE_LOGO
+	bool "Boot logo is 565REL file"
+
+config FB_565RGB_LOGO
+	bool "Boot logo a 565RGB file"
+
+endchoice
+
+
+config FB_ANDROID_JZ4755SOC
+	tristate "JZ4755SOC ANDROID LCD controller support"
+	depends on FB && JZSOC
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	---help---
+	   JZSOC ANDROID LCD Controller driver support.
+
+config IPU_ANDROID_JZ4755
+	bool  "Jz4755 android ipu support"
+	depends on FB_ANDROID_JZ4755SOC && SOC_JZ4750D
+	---help---
+	   Use JZ4755 Android IPU, if need, please select this.
+config FB_JZ4755_ANDROID_LCD
+	tristate "JZ4755 Android LCD Controller support"
+	depends on FB_ANDROID_JZ4755SOC && SOC_JZ4750D
+	---help---
+	   JZ4755 Android LCD Controller driver.
+	   JZ4755 Android LCD Controller support OSD function(refer jz4755_lcdc_spec.pdf).
+	   JZ4755 Android LCD OSD implement 2 framebuffer layers: foreground0 and foreground1.
+#	   JZ4755 LCD driver support 2 foregrounds default.
+
+choice
+	prompt "Android LCD Type Select"	
+	depends on FB_JZ4755_ANDROID_LCD
+	default FB_JZ4755_ANDROID_TFT_LCD
+
+config FB_JZ4755_ANDROID_TFT
+	bool "JZ4755 Android LCD Controller TFT LCD support"
+
+endchoice
+
+choice
+	depends on FB_JZ4755_ANDROID_LCD && FB_JZ4755_ANDROID_TFT
+	prompt "JZ4755 Android LCD TFT Panels Support"
+	default JZ4755_ANDROID_LCD_AUO_A043FL01V2
+	---help---
+	   Please select the lcd panel in you board
+
+config JZ4755_ANDROID_LCD_AUO_A043FL01V2
+	bool "AUO A043FL01V2 TFT panel (480x272)(24bits)"
+
+config JZ4755_ANDROID_LCD_TOPPOLY_TD043MGEB1
+	bool "TOPPOLY_TD043MGEB1 TFT panel(800x480)(24bit mode)"
+
+endchoice
+
+
+config FB_ANDROID_JZSOC
+	tristate "JZSOC ANDROID LCD controller support"
+	depends on FB && JZSOC
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	---help---
+	   JZSOC ANDROID LCD Controller driver support.
+
+config IPU_ANDROID_JZ4750
+	bool  "Jz4750 android ipu support"
+	depends on FB_ANDROID_JZSOC && SOC_JZ4750
+	---help---
+	   Use JZ4750 Android IPU, if need, please select this.
+config FB_JZ4750_ANDROID_LCD
+	tristate "JZ4750 Android LCD Controller support"
+	depends on FB_ANDROID_JZSOC && SOC_JZ4750 
+	---help---
+	   JZ4750 Android LCD Controller driver.
+	   JZ4750 Android LCD Controller support OSD function(refer jz4750_lcdc_spec.pdf).
+	   JZ4750 Android LCD OSD implement 2 framebuffer layers: foreground0 and foreground1.
+#	   JZ4750 LCD driver support 2 foregrounds default.
+
+choice
+	prompt "Android LCD Type Select"	
+	depends on FB_JZ4750_ANDROID_LCD
+	default FB_JZ4750_ANDROID_TFT_LCD
+
+config FB_JZ4750_ANDROID_TFT
+	bool "JZ4750 Android LCD Controller TFT LCD support"
+
+endchoice
+
+choice
+	depends on FB_JZ4750_ANDROID_LCD && FB_JZ4750_ANDROID_TFT
+	prompt "JZ4750 Android LCD TFT Panels Support"
+	default JZ4750_ANDROID_LCD_AUO_A043FL01V2
+	---help---
+	   Please select the lcd panel in you board
+
+config JZ4750_ANDROID_LCD_AUO_A043FL01V2
+	bool "AUO A043FL01V2 TFT panel (480x272)(24bits)"
+
+config JZ4750_ANDROID_LCD_TOPPOLY_TD043MGEB1
+	bool "TOPPOLY_TD043MGEB1 TFT panel(800x480)(24bit mode)"
+
+endchoice
+
+/************************************************************/
+config FB_JZSOC
+	tristate "JZSOC LCD controller support"
+	depends on FB && JZSOC
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	---help---
+	   JZSOC LCD Controller and Smart LCD Controller driver support.
+
+config FB_JZ4740_SLCD
+	tristate "JZ4740 Smart LCD controller support"
+	depends on FB_JZSOC && SOC_JZ4740
+	default n
+	---help---
+	  This is the frame buffer device driver for the JZ4740 Smart LCD controller. 
+	  If select this, please set <JZ4740 LCD controller support> to <n>.
+
+choice
+	depends on FB_JZ4740_SLCD
+	prompt "SLCD Panel"
+	default JZ_SLCD_LGDP4551_8BUS
+
+config JZ_SLCD_LGDP4551
+	bool "LG LGDP4551 Smart LCD panel"
+	---help---
+	Driver for Smart LCD LGDP4551, 8-bit sytem interface, 16BPP.
+
+config JZ_SLCD_SPFD5420A
+	bool "SPFD5420A Smart LCD panel"
+	---help---
+	Driver for Smart LCD SPFD5420A 18-bit sytem interface, 18BPP.
+	
+config JZ_SLCD_TRULY
+	bool "TRULY Smart LCD panel (MAX Pixels 400x240)"
+	---help---
+
+endchoice
+
+config FB_JZLCD_4730_4740
+	tristate "JZ4730 JZ4740 LCD controller support"
+	depends on FB_JZSOC && (SOC_JZ4730 || SOC_JZ4740)
+	help
+	  This is the frame buffer device driver for the JZ4730 and JZ4740 LCD controller.
+config JZLCD_FRAMEBUFFER_MAX
+	int "Default FrameBuffer num"
+	depends on FB_JZLCD_4730_4740
+	default "1"
+       	---help---
+	  JZ LCD driver support multi-framebuffers for video applications.
+config JZLCD_FRAMEBUFFER_ROTATE_SUPPORT
+	bool "JZLCD FrameBuffer Rotate Support(For TEST)"
+	depends on FB_JZLCD_4730_4740
+	default n
+       	---help---
+	  JZ LCD driver framebuffer rotate support. Rotate angle can be 0,90,180,270.
+	  Note, this fearture is implemented by software, and will cost a lot of cpu capcity.
+	  That is to say, if you select this function, you system will become slowly.
+	  Rotate cost cpu about:
+	  ratate angle 0'C:    0% cpu
+	  ratate angle 90'C:  40% cpu
+	  ratate angle 180'C: 20% cpu
+	  ratate angle 270'C: 40% cpu
+
+config JZLCD_FRAMEBUFFER_DEFAULT_ROTATE_ANGLE
+	int "FrameBuffer default rotate angle"
+	depends on JZLCD_FRAMEBUFFER_ROTATE_SUPPORT
+	default 0
+       	---help---
+	  JZ LCD driver framebuffer angle value can be:
+	  	0:	0'C
+	  	1:	90'C
+	  	2:	180'C
+	  	3:	270'C
+config JZLCD_FRAMEBUFFER_BPP
+	int "FrameBuffer bit per pixel"
+	depends on JZLCD_FRAMEBUFFER_ROTATE_SUPPORT
+	default 32
+       	---help---
+	  JZ LCD driver framebuffer support 8bpp, 16bpp, 32bpp
+choice
+	depends on FB_JZLCD_4730_4740
+	prompt "LCD Panel"
+	default JZLCD_SAMSUNG_LTP400WQF01
+
+config JZLCD_SHARP_LQ035Q7
+	bool "SHARP LQ035Q7 TFT panel (240x320)"
+
+config JZLCD_SAMSUNG_LTS350Q1
+	bool "SAMSUNG LTS350Q1 TFT panel (240x320)"
+
+config JZLCD_SAMSUNG_LTV350QVF04
+	bool "SAMSUNG LTV350QV_F04 TFT panel (320x240)"
+
+config JZLCD_SAMSUNG_LTP400WQF01
+	bool "SAMSUNG LTP400WQF01 TFT panel (480x272)(16bits)"
+
+config JZLCD_SAMSUNG_LTP400WQF02
+	bool "SAMSUNG LTP400WQF02 TFT panel (480x272)(18bits)"
+
+config JZLCD_AUO_A030FL01_V1
+	bool "AUO A030FL01_V1 TFT panel (480x272)"
+
+config JZLCD_TRULY_TFTG320240DTSW
+	bool "TRULY TFTG320240DTSW TFT panel (320x240)"
+
+config JZLCD_TRULY_TFTG320240DTSW_SERIAL
+	bool "TRULY TFTG320240DTSW TFT panel (320x240)(8bit-serial mode)"
+
+config JZLCD_TRULY_TFTG240320UTSW_63W_E
+      	bool "TRULY TFTG240320UTSW-63W-E TFT panel (240x320,2.5in)"
+
+config JZLCD_FOXCONN_PT035TN01
+	bool "FOXCONN PT035TN01 TFT panel (320x240)"
+
+config JZLCD_INNOLUX_PT035TN01_SERIAL
+     	bool "INNOLUX PT035TN01 TFT panel (320x240,3.5in)(8bit-serial mode)"
+
+config JZLCD_TOSHIBA_LTM084P363
+	bool "Toshiba LTM084P363 TFT panel (800x600)"
+
+config JZLCD_HYNIX_HT10X21
+	bool "Hynix HT10X21_300 TFT panel (1024x768)"
+
+config JZLCD_INNOLUX_AT080TN42
+      	bool "INNOLUX AT080TN42 TFT panel (800x600)"
+
+config JZLCD_CSTN_800x600
+	bool "800x600 colorDSTN panel"
+
+config JZLCD_CSTN_320x240
+	bool "320x240 colorSTN panel"
+
+config JZLCD_MSTN_480x320
+	bool "480x320 monoSTN panel"
+
+config JZLCD_MSTN_320x240
+	bool "320x240 monoSTN panel"
+
+config JZLCD_MSTN_240x128
+	bool "240x128 monoSTN panel"
+
+config JZLCD_MSTN_INVERSE
+	bool "Use an inverse color display."
+	depends on (JZLCD_MSTN_480x320 || JZLCD_MSTN_240x128)
+
+endchoice
+
+
+config FB_JZ4750_TVE
+	bool  "Jz4750 TV Encode support"
+	depends on FB_JZSOC && (SOC_JZ4750 || SOC_JZ4750D)
+	---help---
+	   Use JZ4750 TV Encoder controller to display on TV.
+
+config IPU_JZ4750
+	bool  "Jz4750 ipu support"
+	depends on FB_JZSOC && (SOC_JZ4750 || SOC_JZ4750D) 
+	---help---
+	   Use JZ4750 IPU, if need, please select this.
+
+config FB_JZ4750_LCD
+	tristate "JZ4750 LCD Controller support"
+	depends on FB_JZSOC && (SOC_JZ4750 || SOC_JZ4750D)
+	---help---
+	   JZ4750 LCD Controller driver.
+	   JZ4750 LCD Controller support OSD function(refer jz4750_lcdc_spec.pdf).
+	   JZ4750 LCD OSD implement 2 framebuffer layers: foreground0 and foreground1.
+#	   JZ4750 LCD driver support only foreground0 default.
+
+choice
+	depends on FB_JZ4750_LCD
+	prompt "JZ4750 LCD OSD Mode select"
+	default JZ4750_LCD_USE_FG1_ONLY
+
+config JZ4750_LCD_USE_FG0_ONLY
+	bool "Only use foreground 0"
+
+config JZ4750_LCD_USE_FG1_ONLY
+	bool "Only use foreground 1"
+
+config JZ4750_LCD_USE_2LAYER_FG
+       bool "Use two-layer foregrounds."
+endchoice
+
+
+choice
+	prompt "LCD Type Select"	
+	depends on FB_JZ4750_LCD
+	default FB_JZ4750_TFT_LCD
+
+config FB_JZ4750_TFT
+	bool "JZ4750 LCD Controller TFT LCD support"
+
+config FB_JZ4750_SLCD
+	bool "JZ4750 LCD Controller Smart LCD support"
+endchoice
+
+choice
+	depends on FB_JZ4750_LCD && FB_JZ4750_TFT
+	prompt "JZ4750 LCD TFT Panels Support"
+	default JZ4750_LCD_SAMSUNG_LTP400WQF02
+	---help---
+	   Please select the lcd panel in you board
+
+config JZ4750_LCD_SAMSUNG_LTP400WQF01
+	bool "SAMSUNG LTP400WQF01 TFT panel (480x272)(16bits)"
+
+config JZ4750_LCD_SAMSUNG_LTP400WQF02
+	bool "SAMSUNG LTP400WQF02 TFT panel (480x272)(18bits)"
+
+config JZ4750_LCD_AUO_A043FL01V2
+	bool "AUO A043FL01V2 TFT panel (480x272)(24bits)"
+
+config JZ4750_LCD_FOXCONN_PT035TN01
+     	bool "FOXCONN PT035TN01 TFT panel (320x240,3.5in)(18bit-parallel mode)"
+
+config JZ4750_LCD_INNOLUX_PT035TN01_SERIAL
+     	bool "INNOLUX PT035TN01 TFT panel (320x240,3.5in)(8bit-serial mode)"
+
+config JZ4750_LCD_TOPPOLY_TD025THEA7_RGB_DELTA
+	bool "TOPPOLY_TD025THEA7 TFT panel(320x240)(serial RGB delta mode)"
+
+config JZ4750_LCD_TRULY_TFTG320240DTSW_18BIT
+	bool "TRULY_TFTG320240DTSW TFT panel (320x240) (Parallel 18bit mode)"
+
+config JZ4750D_VGA_DISPLAY
+	depends on SOC_JZ4750D
+	bool "Jz4750D VGA Display, Jz4750 don't support"
+endchoice
+
+choice
+	depends on FB_JZ4750_LCD && FB_JZ4750_SLCD
+	prompt "JZ4750 Smart LCD Panels Support"
+	default JZ4750_SLCD_KGM701A3_TFT_SPFD5420A
+	---help---
+	   Please select the lcd panel in you board
+config JZ4750_LCD_TRULY_TFT_GG1P0319LTSW_W
+	bool "TRULY_TFT_GG1P0319LTSW_W (240x320) (Smart LCD 16bit)"
+
+config JZ4750_SLCD_KGM701A3_TFT_SPFD5420A
+	bool "KGM701A3_TFT_SPFD5420A (400x240) (Smart LCD 18bit)"
+
+endchoice
+
+config FB_JZ4760_LCD
+	tristate "JZ4760 LCD Controller support"
+	depends on FB_JZSOC && SOC_JZ4760
+	---help---
+	   JZ4760 LCD Controller driver.
+	   JZ4760 LCD Controller support OSD function(refer jz4760_lcdc_spec.pdf).
+	   JZ4760 LCD OSD implement 2 framebuffer layers: foreground0 and foreground1.
+#	   JZ4760 LCD driver support only foreground0 default.
+
+choice
+	depends on FB_JZ4760_LCD
+	prompt "JZ4760 LCD OSD Mode select"
+	default JZ4760_LCD_USE_FG1_ONLY
+
+config JZ4760_LCD_USE_FG0_ONLY
+	bool "Only use foreground 0"
+
+config JZ4760_LCD_USE_FG1_ONLY
+	bool "Only use foreground 1"
+
+config JZ4760_LCD_USE_2LAYER_FG
+       bool "Use two-layer foregrounds."
+endchoice
+
+
+choice
+	prompt "LCD Type Select"	
+	depends on FB_JZ4760_LCD
+	default FB_JZ4760_TFT_LCD
+
+config FB_JZ4760_TFT
+	bool "JZ4760 LCD Controller TFT LCD support"
+
+config FB_JZ4760_SLCD
+	bool "JZ4760 LCD Controller Smart LCD support"
+endchoice
+
+choice
+	depends on FB_JZ4760_LCD && FB_JZ4760_TFT
+	prompt "JZ4760 LCD TFT Panels Support"
+	default JZ4760_LCD_SAMSUNG_LTP400WQF02
+	---help---
+	   Please select the lcd panel in you board
+
+config JZ4760_LCD_SAMSUNG_LTP400WQF01
+	bool "SAMSUNG LTP400WQF01 TFT panel (480x272)(16bits)"
+
+config JZ4760_LCD_SAMSUNG_LTP400WQF02
+	bool "SAMSUNG LTP400WQF02 TFT panel (480x272)(18bits)"
+
+config JZ4760_LCD_AUO_A043FL01V2
+	bool "AUO A043FL01V2 TFT panel (480x272)(24bits)"
+
+config JZ4760_LCD_FOXCONN_PT035TN01
+     	bool "FOXCONN PT035TN01 TFT panel (320x240,3.5in)(18bit-parallel mode)"
+
+config JZ4760_LCD_INNOLUX_PT035TN01_SERIAL
+     	bool "INNOLUX PT035TN01 TFT panel (320x240,3.5in)(8bit-serial mode)"
+
+config JZ4760_LCD_TOPPOLY_TD025THEA7_RGB_DELTA
+	bool "TOPPOLY_TD025THEA7 TFT panel(320x240)(serial RGB delta mode)"
+
+config JZ4760_LCD_TRULY_TFTG320240DTSW_18BIT
+	bool "TRULY_TFTG320240DTSW TFT panel (320x240) (Parallel 18bit mode)"
+
+config JZ4760_VGA_DISPLAY
+	bool "Jz4760 VGA Display, Jz4760 don't support"
+endchoice
+
+choice
+	depends on FB_JZ4760_LCD && FB_JZ4760_SLCD
+	prompt "JZ4760 Smart LCD Panels Support"
+	default JZ4760_SLCD_KGM701A3_TFT_SPFD5420A
+	---help---
+	   Please select the lcd panel in you board
+config JZ4760_LCD_TRULY_TFT_GG1P0319LTSW_W
+	bool "TRULY_TFT_GG1P0319LTSW_W (240x320) (Smart LCD 16bit)"
+
+config JZ4760_SLCD_KGM701A3_TFT_SPFD5420A
+	bool "KGM701A3_TFT_SPFD5420A (400x240) (Smart LCD 18bit)"
+
+endchoice
+
+
 config FB_CIRRUS
 	tristate "Cirrus Logic support"
 	depends on FB && (ZORRO || PCI)
diff -ru linux-2.6/drivers/video/Makefile /plain/src/qi/linux-2.6.27.git.svn/drivers/video/Makefile
--- linux-2.6/drivers/video/Makefile	2009-08-17 23:58:02.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/drivers/video/Makefile	2009-08-12 10:39:09.000000000 +0200
@@ -28,6 +28,17 @@
 obj-$(CONFIG_FB_DEFERRED_IO)   += fb_defio.o
 
 # Hardware specific drivers go first
+obj-$(CONFIG_JZSOC_BOOT_LOGO) += logo.o
+obj-$(CONFIG_FB_JZLCD_4730_4740)  += jzlcd.o
+obj-$(CONFIG_FB_JZ4740_SLCD)      += jz4740_slcd.o
+obj-$(CONFIG_FB_JZ4750_TFT)       += jz4750_lcd.o
+obj-$(CONFIG_FB_JZ4750_SLCD)      += jz4750_slcd.o
+obj-$(CONFIG_FB_JZ4760_TFT)       += jz4760_lcd.o
+obj-$(CONFIG_FB_JZ4760_SLCD)      += jz4760_slcd.o
+obj-$(CONFIG_FB_JZ4750_TVE)       += jz4750_tve.o
+obj-$(CONFIG_FB_JZ4750_ANDROID_TFT)       += jz4750_android_lcd.o
+obj-$(CONFIG_FB_JZ4755_ANDROID_TFT)       += jz4755_android_lcd.o
+
 obj-$(CONFIG_FB_AMIGA)            += amifb.o c2p.o
 obj-$(CONFIG_FB_AM200EPD)         += am200epd.o
 obj-$(CONFIG_FB_ARC)              += arcfb.o
diff -ru linux-2.6/include/asm-mips/bootinfo.h /plain/src/qi/linux-2.6.27.git.svn/include/asm-mips/bootinfo.h
--- linux-2.6/include/asm-mips/bootinfo.h	2009-08-17 23:58:03.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/include/asm-mips/bootinfo.h	2009-08-12 10:39:09.000000000 +0200
@@ -57,6 +57,15 @@
 #define	MACH_MIKROTIK_RB532	0	/* Mikrotik RouterBoard 532 	*/
 #define MACH_MIKROTIK_RB532A	1	/* Mikrotik RouterBoard 532A 	*/
 
+/*
+ * Valid machtype for group INGENIC
+ */
+#define  MACH_INGENIC_JZ4730	0	/* JZ4730 SOC		*/
+#define  MACH_INGENIC_JZ4740	1	/* JZ4740 SOC		*/
+#define  MACH_INGENIC_JZ4750	2	/* JZ4750 SOC		*/
+#define  MACH_INGENIC_JZ4750D	3	/* JZ4750D SOC		*/
+#define  MACH_INGENIC_JZ4760	4	/* JZ4760 SOC		*/
+
 #define CL_SIZE			COMMAND_LINE_SIZE
 
 extern char *system_type;
diff -ru linux-2.6/include/asm-mips/cpu.h /plain/src/qi/linux-2.6.27.git.svn/include/asm-mips/cpu.h
--- linux-2.6/include/asm-mips/cpu.h	2009-08-17 23:58:03.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/include/asm-mips/cpu.h	2009-08-12 10:39:09.000000000 +0200
@@ -33,8 +33,11 @@
 #define PRID_COMP_TOSHIBA	0x070000
 #define PRID_COMP_LSI		0x080000
 #define PRID_COMP_LEXRA		0x0b0000
-
-
+#if defined(CONFIG_JZ_FPGA) && defined(CONFIG_SOC_JZ4760)
+#define PRID_COMP_INGENIC	0xd80000
+#else
+#define PRID_COMP_INGENIC	0xd00000
+#endif
 /*
  * Assigned values for the product ID register.  In order to detect a
  * certain CPU type exactly eventually additional registers may need to
@@ -114,6 +117,12 @@
 #define PRID_IMP_BCM3302	0x9000
 
 /*
+ * These are the PRID's for when 23:16 == PRID_COMP_INGENIC
+ */
+
+#define PRID_IMP_JZRISC        0x0200
+
+/*
  * Definitions for 7:0 on legacy processors
  */
 
@@ -204,6 +213,11 @@
 	 */
 	CPU_5KC, CPU_20KC, CPU_25KF, CPU_SB1, CPU_SB1A, CPU_LOONGSON2,
 
+	/*
+	 * Ingenic class processors
+	 */
+	CPU_JZRISC, CPU_XBURST,
+
 	CPU_LAST
 };
 
diff -ru linux-2.6/include/asm-mips/mach-generic/irq.h /plain/src/qi/linux-2.6.27.git.svn/include/asm-mips/mach-generic/irq.h
--- linux-2.6/include/asm-mips/mach-generic/irq.h	2009-08-17 23:58:03.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/include/asm-mips/mach-generic/irq.h	2009-08-12 10:39:09.000000000 +0200
@@ -9,7 +9,7 @@
 #define __ASM_MACH_GENERIC_IRQ_H
 
 #ifndef NR_IRQS
-#define NR_IRQS	128
+#define NR_IRQS	256
 #endif
 
 #ifdef CONFIG_I8259
diff -ru linux-2.6/include/asm-mips/ptrace.h /plain/src/qi/linux-2.6.27.git.svn/include/asm-mips/ptrace.h
--- linux-2.6/include/asm-mips/ptrace.h	2009-08-17 23:58:03.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/include/asm-mips/ptrace.h	2009-08-12 10:39:09.000000000 +0200
@@ -79,7 +79,12 @@
 /*
  * Does the process account for user or for system time?
  */
+
+#if defined(CONFIG_JZ_TCSM)
+#define user_mode(regs) ((((regs)->cp0_status & KU_MASK) == KU_USER) || (((regs)->cp0_status & 0x08000000) == 0x08000000))
+# else
 #define user_mode(regs) (((regs)->cp0_status & KU_MASK) == KU_USER)
+#endif
 
 #define instruction_pointer(regs) ((regs)->cp0_epc)
 #define profile_pc(regs) instruction_pointer(regs)
diff -ru linux-2.6/include/asm-mips/r4kcache.h /plain/src/qi/linux-2.6.27.git.svn/include/asm-mips/r4kcache.h
--- linux-2.6/include/asm-mips/r4kcache.h	2009-08-17 23:58:03.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/include/asm-mips/r4kcache.h	2009-08-12 10:39:09.000000000 +0200
@@ -17,6 +17,58 @@
 #include <asm/cpu-features.h>
 #include <asm/mipsmtregs.h>
 
+#ifdef CONFIG_JZRISC
+
+#define K0_TO_K1()				\
+do {						\
+	unsigned long __k0_addr;		\
+						\
+	__asm__ __volatile__(			\
+	"la %0, 1f\n\t"				\
+	"or	%0, %0, %1\n\t"			\
+	"jr	%0\n\t"				\
+	"nop\n\t"				\
+	"1: nop\n"				\
+	: "=&r"(__k0_addr)			\
+	: "r" (0x20000000) );			\
+} while(0)
+
+#define K1_TO_K0()				\
+do {						\
+	unsigned long __k0_addr;		\
+	__asm__ __volatile__(			\
+	"nop;nop;nop;nop;nop;nop;nop\n\t"	\
+	"la %0, 1f\n\t"				\
+	"jr	%0\n\t"				\
+	"nop\n\t"				\
+	"1:	nop\n"				\
+	: "=&r" (__k0_addr));			\
+} while (0)
+
+#define INVALIDATE_BTB()			\
+do {						\
+	unsigned long tmp;			\
+	__asm__ __volatile__(			\
+	".set mips32\n\t"			\
+	"mfc0 %0, $16, 7\n\t"			\
+	"nop\n\t"				\
+	"ori %0, 2\n\t"				\
+	"mtc0 %0, $16, 7\n\t"			\
+	"nop\n\t"				\
+	: "=&r" (tmp));				\
+} while (0)
+
+#define SYNC_WB() __asm__ __volatile__ ("sync")
+
+#else /* CONFIG_JZRISC */
+
+#define K0_TO_K1() do { } while (0)
+#define K1_TO_K0() do { } while (0)
+#define INVALIDATE_BTB() do { } while (0)
+#define SYNC_WB() do { } while (0)
+
+#endif /* CONFIG_JZRISC */
+
 /*
  * This macro return a properly sign-extended address suitable as base address
  * for indexed cache operations.  Two issues here:
@@ -144,6 +196,7 @@
 {
 	__iflush_prologue
 	cache_op(Index_Invalidate_I, addr);
+	INVALIDATE_BTB();
 	__iflush_epilogue
 }
 
@@ -151,6 +204,7 @@
 {
 	__dflush_prologue
 	cache_op(Index_Writeback_Inv_D, addr);
+	SYNC_WB();
 	__dflush_epilogue
 }
 
@@ -163,6 +217,7 @@
 {
 	__iflush_prologue
 	cache_op(Hit_Invalidate_I, addr);
+	INVALIDATE_BTB();
 	__iflush_epilogue
 }
 
@@ -170,6 +225,7 @@
 {
 	__dflush_prologue
 	cache_op(Hit_Writeback_Inv_D, addr);
+	SYNC_WB();
 	__dflush_epilogue
 }
 
@@ -177,6 +233,7 @@
 {
 	__dflush_prologue
 	cache_op(Hit_Invalidate_D, addr);
+	SYNC_WB();
 	__dflush_epilogue
 }
 
@@ -209,6 +266,7 @@
 static inline void protected_flush_icache_line(unsigned long addr)
 {
 	protected_cache_op(Hit_Invalidate_I, addr);
+	INVALIDATE_BTB();
 }
 
 /*
@@ -220,6 +278,7 @@
 static inline void protected_writeback_dcache_line(unsigned long addr)
 {
 	protected_cache_op(Hit_Writeback_Inv_D, addr);
+	SYNC_WB();
 }
 
 static inline void protected_writeback_scache_line(unsigned long addr)
@@ -396,20 +455,132 @@
 __BUILD_BLAST_CACHE(d, dcache, Index_Writeback_Inv_D, Hit_Writeback_Inv_D, 16)
 __BUILD_BLAST_CACHE(i, icache, Index_Invalidate_I, Hit_Invalidate_I, 16)
 __BUILD_BLAST_CACHE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 16)
+#ifndef CONFIG_JZRISC
 __BUILD_BLAST_CACHE(d, dcache, Index_Writeback_Inv_D, Hit_Writeback_Inv_D, 32)
 __BUILD_BLAST_CACHE(i, icache, Index_Invalidate_I, Hit_Invalidate_I, 32)
+#endif
 __BUILD_BLAST_CACHE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 32)
 __BUILD_BLAST_CACHE(i, icache, Index_Invalidate_I, Hit_Invalidate_I, 64)
 __BUILD_BLAST_CACHE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 64)
 __BUILD_BLAST_CACHE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 128)
 
 __BUILD_BLAST_CACHE(inv_d, dcache, Index_Writeback_Inv_D, Hit_Invalidate_D, 16)
+#ifndef CONFIG_JZRISC
 __BUILD_BLAST_CACHE(inv_d, dcache, Index_Writeback_Inv_D, Hit_Invalidate_D, 32)
+#endif
 __BUILD_BLAST_CACHE(inv_s, scache, Index_Writeback_Inv_SD, Hit_Invalidate_SD, 16)
 __BUILD_BLAST_CACHE(inv_s, scache, Index_Writeback_Inv_SD, Hit_Invalidate_SD, 32)
 __BUILD_BLAST_CACHE(inv_s, scache, Index_Writeback_Inv_SD, Hit_Invalidate_SD, 64)
 __BUILD_BLAST_CACHE(inv_s, scache, Index_Writeback_Inv_SD, Hit_Invalidate_SD, 128)
 
+#ifdef CONFIG_JZRISC
+
+static inline void blast_dcache32(void)
+{
+	unsigned long start = INDEX_BASE;
+	unsigned long end = start + current_cpu_data.dcache.waysize;
+	unsigned long ws_inc = 1UL << current_cpu_data.dcache.waybit;
+	unsigned long ws_end = current_cpu_data.dcache.ways <<
+	                       current_cpu_data.dcache.waybit;
+	unsigned long ws, addr;
+
+	for (ws = 0; ws < ws_end; ws += ws_inc)
+		for (addr = start; addr < end; addr += 0x400)
+			cache32_unroll32(addr|ws,Index_Writeback_Inv_D);
+
+	SYNC_WB();
+}
+
+static inline void blast_dcache32_page(unsigned long page)
+{
+	unsigned long start = page;
+	unsigned long end = page + PAGE_SIZE;
+
+	do {
+		cache32_unroll32(start,Hit_Writeback_Inv_D);
+		start += 0x400;
+	} while (start < end);
+
+	SYNC_WB();
+}
+
+static inline void blast_dcache32_page_indexed(unsigned long page)
+{
+	unsigned long indexmask = current_cpu_data.dcache.waysize - 1;
+	unsigned long start = INDEX_BASE + (page & indexmask);
+	unsigned long end = start + PAGE_SIZE;
+	unsigned long ws_inc = 1UL << current_cpu_data.dcache.waybit;
+	unsigned long ws_end = current_cpu_data.dcache.ways <<
+	                       current_cpu_data.dcache.waybit;
+	unsigned long ws, addr;
+
+	for (ws = 0; ws < ws_end; ws += ws_inc)
+		for (addr = start; addr < end; addr += 0x400)
+			cache32_unroll32(addr|ws,Index_Writeback_Inv_D);
+
+	SYNC_WB();
+}
+
+static inline void blast_icache32(void)
+{
+	unsigned long start = INDEX_BASE;
+	unsigned long end = start + current_cpu_data.icache.waysize;
+	unsigned long ws_inc = 1UL << current_cpu_data.icache.waybit;
+	unsigned long ws_end = current_cpu_data.icache.ways <<
+	                       current_cpu_data.icache.waybit;
+	unsigned long ws, addr;
+
+	K0_TO_K1();
+
+	for (ws = 0; ws < ws_end; ws += ws_inc)
+		for (addr = start; addr < end; addr += 0x400)
+			cache32_unroll32(addr|ws,Index_Invalidate_I);
+
+	INVALIDATE_BTB();
+
+	K1_TO_K0();
+}
+
+static inline void blast_icache32_page(unsigned long page)
+{
+	unsigned long start = page;
+	unsigned long end = page + PAGE_SIZE;
+
+	K0_TO_K1();
+
+	do {
+		cache32_unroll32(start,Hit_Invalidate_I);
+		start += 0x400;
+	} while (start < end);
+
+	INVALIDATE_BTB();
+
+	K1_TO_K0();
+}
+
+static inline void blast_icache32_page_indexed(unsigned long page)
+{
+	unsigned long indexmask = current_cpu_data.icache.waysize - 1;
+	unsigned long start = INDEX_BASE + (page & indexmask);
+	unsigned long end = start + PAGE_SIZE;
+	unsigned long ws_inc = 1UL << current_cpu_data.icache.waybit;
+	unsigned long ws_end = current_cpu_data.icache.ways <<
+	                       current_cpu_data.icache.waybit;
+	unsigned long ws, addr;
+
+	K0_TO_K1();
+
+	for (ws = 0; ws < ws_end; ws += ws_inc)
+		for (addr = start; addr < end; addr += 0x400)
+			cache32_unroll32(addr|ws,Index_Invalidate_I);
+
+	INVALIDATE_BTB();
+
+	K1_TO_K0();
+}
+
+#endif /* CONFIG_JZRISC */
+
 /* build blast_xxx_range, protected_blast_xxx_range */
 #define __BUILD_BLAST_CACHE_RANGE(pfx, desc, hitop, prot) \
 static inline void prot##blast_##pfx##cache##_range(unsigned long start, \
@@ -431,13 +602,73 @@
 	__##pfx##flush_epilogue						\
 }
 
+#ifndef CONFIG_JZRISC
 __BUILD_BLAST_CACHE_RANGE(d, dcache, Hit_Writeback_Inv_D, protected_)
+#endif
 __BUILD_BLAST_CACHE_RANGE(s, scache, Hit_Writeback_Inv_SD, protected_)
+#ifndef CONFIG_JZRISC
 __BUILD_BLAST_CACHE_RANGE(i, icache, Hit_Invalidate_I, protected_)
 __BUILD_BLAST_CACHE_RANGE(d, dcache, Hit_Writeback_Inv_D, )
+#endif
 __BUILD_BLAST_CACHE_RANGE(s, scache, Hit_Writeback_Inv_SD, )
 /* blast_inv_dcache_range */
 __BUILD_BLAST_CACHE_RANGE(inv_d, dcache, Hit_Invalidate_D, )
 __BUILD_BLAST_CACHE_RANGE(inv_s, scache, Hit_Invalidate_SD, )
 
+#ifdef CONFIG_JZRISC
+
+static inline void protected_blast_dcache_range(unsigned long start,
+						unsigned long end)
+{
+	unsigned long lsize = cpu_dcache_line_size();
+	unsigned long addr = start & ~(lsize - 1);
+	unsigned long aend = (end - 1) & ~(lsize - 1);
+
+	while (1) {
+		protected_cache_op(Hit_Writeback_Inv_D, addr);
+		if (addr == aend)
+			break;
+		addr += lsize;
+	}
+	SYNC_WB();
+}
+
+static inline void protected_blast_icache_range(unsigned long start,
+						unsigned long end)
+{
+	unsigned long lsize = cpu_icache_line_size();
+	unsigned long addr = start & ~(lsize - 1);
+	unsigned long aend = (end - 1) & ~(lsize - 1);
+
+	K0_TO_K1();
+
+	while (1) {
+		protected_cache_op(Hit_Invalidate_I, addr);
+		if (addr == aend)
+			break;
+		addr += lsize;
+	}
+	INVALIDATE_BTB();
+
+	K1_TO_K0();
+}
+
+static inline void blast_dcache_range(unsigned long start,
+				      unsigned long end)
+{
+	unsigned long lsize = cpu_dcache_line_size();
+	unsigned long addr = start & ~(lsize - 1);
+	unsigned long aend = (end - 1) & ~(lsize - 1);
+
+	while (1) {
+		cache_op(Hit_Writeback_Inv_D, addr);
+		if (addr == aend)
+			break;
+		addr += lsize;
+	}
+	SYNC_WB();
+}
+
+#endif /* CONFIG_JZRISC */
+
 #endif /* _ASM_R4KCACHE_H */
diff -ru linux-2.6/include/asm-mips/signal.h /plain/src/qi/linux-2.6.27.git.svn/include/asm-mips/signal.h
--- linux-2.6/include/asm-mips/signal.h	2009-08-17 23:58:03.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/include/asm-mips/signal.h	2009-08-12 10:39:09.000000000 +0200
@@ -11,6 +11,11 @@
 
 #include <linux/types.h>
 
+/* Avoid too many header ordering problems.  */
+struct siginfo;
+
+#ifdef __KERNEL__
+
 #define _NSIG		128
 #define _NSIG_BPW	(sizeof(unsigned long) * 8)
 #define _NSIG_WORDS	(_NSIG / _NSIG_BPW)
@@ -21,6 +26,14 @@
 
 typedef unsigned long old_sigset_t;		/* at least 32 bits */
 
+#else
+/* Here we must cater to libcs that poke about in kernel headers.  */
+
+#define NSIG		32
+typedef unsigned long sigset_t;
+
+#endif /* __KERNEL__ */
+
 #define SIGHUP		 1	/* Hangup (POSIX).  */
 #define SIGINT		 2	/* Interrupt (ANSI).  */
 #define SIGQUIT		 3	/* Quit (POSIX).  */
@@ -55,6 +68,9 @@
 #define SIGPROF		29	/* Profiling alarm clock (4.2 BSD).  */
 #define SIGXCPU		30	/* CPU limit exceeded (4.2 BSD).  */
 #define SIGXFSZ		31	/* File size limit exceeded (4.2 BSD).  */
+/* Define these two used by Android's bionic */
+#define	SIGUNUSED	SIGSYS
+#define SIGSTKFLT	SIGEMT
 
 /* These should not be considered constants from userland.  */
 #define SIGRTMIN	32
@@ -111,16 +127,38 @@
 
 #include <asm-generic/signal.h>
 
+#ifdef __KERNEL__
+
 struct sigaction {
 	unsigned int	sa_flags;
 	__sighandler_t	sa_handler;
 	sigset_t	sa_mask;
+	__sigrestore_t  sa_restorer;
 };
 
 struct k_sigaction {
 	struct sigaction sa;
 };
 
+#else
+/* Here we must cater to libcs that poke about in kernel headers.  */
+
+struct sigaction {
+	unsigned long sa_flags;
+	union {
+		__sighandler_t _sa_handler;
+		void (*_sa_sigaction)(int, struct siginfo *, void *);
+	} _u;
+	sigset_t sa_mask;
+	unsigned long pad[3]; /* padding for sa_mask */
+	void (*sa_restorer)(void);
+};
+
+#define sa_handler	_u._sa_handler
+#define sa_sigaction	_u._sa_sigaction
+
+#endif
+
 /* IRIX compatible stack_t  */
 typedef struct sigaltstack {
 	void __user *ss_sp;
diff -ru linux-2.6/include/asm-mips/suspend.h /plain/src/qi/linux-2.6.27.git.svn/include/asm-mips/suspend.h
--- linux-2.6/include/asm-mips/suspend.h	2009-08-17 23:58:03.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/include/asm-mips/suspend.h	2009-08-12 10:39:09.000000000 +0200
@@ -1,6 +1,11 @@
 #ifndef __ASM_SUSPEND_H
 #define __ASM_SUSPEND_H
 
-/* Somewhen...  Maybe :-)  */
+/* Jz suspend interfaces */
+
+#if defined(CONFIG_PM) && defined(CONFIG_JZSOC)
+extern int jz_pm_init(void);
+static inline int arch_prepare_suspend(void) { return 0; }
+#endif
 
 #endif /* __ASM_SUSPEND_H */
diff -ru linux-2.6/include/linux/miscdevice.h /plain/src/qi/linux-2.6.27.git.svn/include/linux/miscdevice.h
--- linux-2.6/include/linux/miscdevice.h	2009-08-17 23:58:03.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/include/linux/miscdevice.h	2009-08-12 10:39:09.000000000 +0200
@@ -30,6 +30,8 @@
 #define TUN_MINOR	     200
 #define	HPET_MINOR	     228
 #define KVM_MINOR            232
+#define TCSM_MINOR           233        /* JZ TCSM for multimedia */
+#define CIM_MINOR            234        /* JZ CIM for multimedia */
 
 struct device;
 
diff -ru linux-2.6/include/linux/mmc/host.h /plain/src/qi/linux-2.6.27.git.svn/include/linux/mmc/host.h
--- linux-2.6/include/linux/mmc/host.h	2009-08-17 23:58:03.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/include/linux/mmc/host.h	2009-08-12 10:39:09.000000000 +0200
@@ -41,6 +41,7 @@
 
 #define MMC_BUS_WIDTH_1		0
 #define MMC_BUS_WIDTH_4		2
+#define MMC_BUS_WIDTH_8		4
 
 	unsigned char	timing;			/* timing specification used */
 
@@ -159,6 +160,15 @@
 
 	struct dentry		*debugfs_root;
 
+#ifdef CONFIG_MMC_EMBEDDED_SDIO
+	struct {
+		struct sdio_cis			*cis;
+		struct sdio_cccr		*cccr;
+		struct sdio_embedded_func	*funcs;
+		int				num_funcs;
+	} embedded_sdio_data;
+#endif
+
 	unsigned long		private[0] ____cacheline_aligned;
 };
 
@@ -167,6 +177,14 @@
 extern void mmc_remove_host(struct mmc_host *);
 extern void mmc_free_host(struct mmc_host *);
 
+#ifdef CONFIG_MMC_EMBEDDED_SDIO
+extern void mmc_set_embedded_sdio_data(struct mmc_host *host,
+				       struct sdio_cis *cis,
+				       struct sdio_cccr *cccr,
+				       struct sdio_embedded_func *funcs,
+				       int num_funcs);
+#endif
+
 static inline void *mmc_priv(struct mmc_host *host)
 {
 	return (void *)host->private;
diff -ru linux-2.6/include/linux/power_supply.h /plain/src/qi/linux-2.6.27.git.svn/include/linux/power_supply.h
--- linux-2.6/include/linux/power_supply.h	2009-08-17 23:58:03.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/include/linux/power_supply.h	2009-08-12 10:39:09.000000000 +0200
@@ -86,7 +86,8 @@
 	POWER_SUPPLY_PROP_ENERGY_NOW,
 	POWER_SUPPLY_PROP_ENERGY_AVG,
 	POWER_SUPPLY_PROP_CAPACITY, /* in percents! */
-	POWER_SUPPLY_PROP_TEMP,
+	POWER_SUPPLY_PROP_TEMP, /* for android, but not supported */
+	POWER_SUPPLY_PROP_VOL,  /* for android, but not supported */
 	POWER_SUPPLY_PROP_TEMP_AMBIENT,
 	POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW,
 	POWER_SUPPLY_PROP_TIME_TO_EMPTY_AVG,
diff -ru linux-2.6/include/linux/suspend.h /plain/src/qi/linux-2.6.27.git.svn/include/linux/suspend.h
--- linux-2.6/include/linux/suspend.h	2009-08-17 23:58:03.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/include/linux/suspend.h	2009-08-12 10:39:09.000000000 +0200
@@ -1,9 +1,11 @@
 #ifndef _LINUX_SUSPEND_H
 #define _LINUX_SUSPEND_H
 
-#if defined(CONFIG_X86) || defined(CONFIG_FRV) || defined(CONFIG_PPC32) || defined(CONFIG_PPC64)
+#if defined(CONFIG_X86) || defined(CONFIG_FRV) || defined(CONFIG_PPC32)\
+	|| defined(CONFIG_PPC64) || defined(CONFIG_MIPS)
 #include <asm/suspend.h>
 #endif
+
 #include <linux/swap.h>
 #include <linux/notifier.h>
 #include <linux/init.h>
@@ -245,6 +247,9 @@
 void save_processor_state(void);
 void restore_processor_state(void);
 
+//void save_processor_state(void){}
+//void restore_processor_state(void){}
+
 /* kernel/power/main.c */
 extern int register_pm_notifier(struct notifier_block *nb);
 extern int unregister_pm_notifier(struct notifier_block *nb);
diff -ru linux-2.6/include/sound/pcm.h /plain/src/qi/linux-2.6.27.git.svn/include/sound/pcm.h
--- linux-2.6/include/sound/pcm.h	2009-08-17 23:58:03.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/include/sound/pcm.h	2009-08-12 10:39:09.000000000 +0200
@@ -107,23 +107,23 @@
 #define SNDRV_PCM_RATE_5512		(1<<0)		/* 5512Hz */
 #define SNDRV_PCM_RATE_8000		(1<<1)		/* 8000Hz */
 #define SNDRV_PCM_RATE_11025		(1<<2)		/* 11025Hz */
-#define SNDRV_PCM_RATE_16000		(1<<3)		/* 16000Hz */
-#define SNDRV_PCM_RATE_22050		(1<<4)		/* 22050Hz */
-#define SNDRV_PCM_RATE_32000		(1<<5)		/* 32000Hz */
-#define SNDRV_PCM_RATE_44100		(1<<6)		/* 44100Hz */
-#define SNDRV_PCM_RATE_48000		(1<<7)		/* 48000Hz */
-#define SNDRV_PCM_RATE_64000		(1<<8)		/* 64000Hz */
-#define SNDRV_PCM_RATE_88200		(1<<9)		/* 88200Hz */
-#define SNDRV_PCM_RATE_96000		(1<<10)		/* 96000Hz */
-#define SNDRV_PCM_RATE_176400		(1<<11)		/* 176400Hz */
-#define SNDRV_PCM_RATE_192000		(1<<12)		/* 192000Hz */
+#define SNDRV_PCM_RATE_12000		(1<<3)		/* 12000Hz */
+#define SNDRV_PCM_RATE_16000		(1<<4)		/* 16000Hz */
+#define SNDRV_PCM_RATE_22050		(1<<5)		/* 22050Hz */
+#define SNDRV_PCM_RATE_24000		(1<<6)		/* 24000Hz */
+#define SNDRV_PCM_RATE_32000		(1<<7)		/* 32000Hz */
+#define SNDRV_PCM_RATE_44100		(1<<8)		/* 44100Hz */
+#define SNDRV_PCM_RATE_48000		(1<<9)		/* 48000Hz */
+#define SNDRV_PCM_RATE_64000		(1<<10)		/* 64000Hz */
+#define SNDRV_PCM_RATE_88200		(1<<11)		/* 88200Hz */
+#define SNDRV_PCM_RATE_96000		(1<<12)		/* 96000Hz */
+#define SNDRV_PCM_RATE_176400		(1<<13)		/* 176400Hz */
+#define SNDRV_PCM_RATE_192000		(1<<14)		/* 192000Hz */
 
 #define SNDRV_PCM_RATE_CONTINUOUS	(1<<30)		/* continuous range */
 #define SNDRV_PCM_RATE_KNOT		(1<<31)		/* supports more non-continuos rates */
 
-#define SNDRV_PCM_RATE_8000_44100	(SNDRV_PCM_RATE_8000|SNDRV_PCM_RATE_11025|\
-					 SNDRV_PCM_RATE_16000|SNDRV_PCM_RATE_22050|\
-					 SNDRV_PCM_RATE_32000|SNDRV_PCM_RATE_44100)
+#define SNDRV_PCM_RATE_8000_44100	(SNDRV_PCM_RATE_8000|SNDRV_PCM_RATE_11025|SNDRV_PCM_RATE_12000|SNDRV_PCM_RATE_16000|SNDRV_PCM_RATE_22050|SNDRV_PCM_RATE_24000|SNDRV_PCM_RATE_32000|SNDRV_PCM_RATE_44100)
 #define SNDRV_PCM_RATE_8000_48000	(SNDRV_PCM_RATE_8000_44100|SNDRV_PCM_RATE_48000)
 #define SNDRV_PCM_RATE_8000_96000	(SNDRV_PCM_RATE_8000_48000|SNDRV_PCM_RATE_64000|\
 					 SNDRV_PCM_RATE_88200|SNDRV_PCM_RATE_96000)
diff -ru linux-2.6/sound/core/pcm_lib.c /plain/src/qi/linux-2.6.27.git.svn/sound/core/pcm_lib.c
--- linux-2.6/sound/core/pcm_lib.c	2009-08-17 23:58:04.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/sound/core/pcm_lib.c	2009-08-12 10:39:09.000000000 +0200
@@ -1875,6 +1875,7 @@
 	return xfer > 0 ? (snd_pcm_sframes_t)xfer : err;
 }
 
+#if 0
 snd_pcm_sframes_t snd_pcm_lib_read(struct snd_pcm_substream *substream, void __user *buf, snd_pcm_uframes_t size)
 {
 	struct snd_pcm_runtime *runtime;
@@ -1892,6 +1893,99 @@
 		return -EINVAL;
 	return snd_pcm_lib_read1(substream, (unsigned long)buf, size, nonblock, snd_pcm_lib_read_transfer);
 }
+#else
+snd_pcm_sframes_t snd_pcm_lib_read(struct snd_pcm_substream *substream, void __user *buf, snd_pcm_uframes_t size)
+{
+	struct snd_pcm_runtime *runtime;
+	int nonblock;
+
+	snd_pcm_sframes_t tmp_frames;
+	snd_pcm_sframes_t final_frames;
+	int channels;
+
+	snd_assert(substream != NULL, return -ENXIO);
+	runtime = substream->runtime;
+	snd_assert(runtime != NULL, return -ENXIO);
+	snd_assert(substream->ops->copy != NULL || runtime->dma_area != NULL, return -EINVAL);
+	if (runtime->status->state == SNDRV_PCM_STATE_OPEN)
+		return -EBADFD;
+
+	nonblock = !!(substream->f_flags & O_NONBLOCK);
+	if (runtime->access != SNDRV_PCM_ACCESS_RW_INTERLEAVED)
+		return -EINVAL;
+
+	/* 
+	 * mono capture process for no mono codec 
+	 * function codec such as ipcood and dlv 
+	 */
+	
+	tmp_frames = snd_pcm_lib_read1(substream, (unsigned long)buf, size, nonblock, snd_pcm_lib_read_transfer);
+	
+	channels = runtime->channels;
+
+	if (channels == 1) {
+		short *tmpbuf = kcalloc(tmp_frames, sizeof(short), GFP_KERNEL);
+		short *src, *dst, *end;
+		
+		memcpy(tmpbuf, buf, frames_to_bytes(runtime, tmp_frames));
+		
+		src = (short *)buf;
+		dst = (short *)tmpbuf;
+		end = dst + tmp_frames - 1;
+	
+		src++;
+		dst++;
+		dst++;
+		final_frames = 1;
+		while (dst <= end) {
+			*src = *dst;
+			final_frames++;
+			src++;
+			dst++;
+			dst++;
+		}
+		tmp_frames = final_frames;
+		kfree(tmpbuf);
+
+#if 0
+		/* when i have time, i will try the code, no kcalloc */
+		snd_assert(runtime->dma_area, return -EFAULT);
+		if (copy_to_user(buf, hwbuf, frames_to_bytes(runtime, frames)))
+			return -EFAULT;
+		
+		unsigned int up_bytes = frames_to_bytes(runtime, frames);
+		
+		int while_cnt = 4;
+		int while_all = up_bytes - 2;
+		
+		while (while_cnt <= while_all) {
+			//printk("[%d = %d]\n",(while_cnt/2),while_cnt);
+			buf[(while_cnt/2)] = buf[while_cnt];
+			//printk("[%d = %d]\n",((while_cnt/2)+1),(while_cnt+1));
+			buf[((while_cnt/2)+1)] = buf[(while_cnt+1)];
+			while_cnt += 4;
+#if 0				       
+			buf[2] = buf[4];
+			buf[3] = buf[5];
+			
+			buf[4] = buf[8];
+			buf[5] = buf[9];
+			
+			buf[6] = buf[12];
+			buf[7] = buf[13];
+			
+			buf[8] = buf[16];
+			buf[9] = buf[17];
+#endif
+		}
+		/* when i have time, i will try the code, no kcalloc */
+#endif
+
+	}
+
+	return tmp_frames;
+}
+#endif
 
 EXPORT_SYMBOL(snd_pcm_lib_read);
 
diff -ru linux-2.6/sound/core/pcm_native.c /plain/src/qi/linux-2.6.27.git.svn/sound/core/pcm_native.c
--- linux-2.6/sound/core/pcm_native.c	2009-08-17 23:58:04.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/sound/core/pcm_native.c	2009-08-12 10:39:09.000000000 +0200
@@ -1756,12 +1756,13 @@
 	return snd_interval_refine(hw_param_interval(params, rule->var), &t);
 }
 
-#if SNDRV_PCM_RATE_5512 != 1 << 0 || SNDRV_PCM_RATE_192000 != 1 << 12
+#if SNDRV_PCM_RATE_5512 != 1 << 0 || SNDRV_PCM_RATE_192000 != 1 << 14
 #error "Change this table"
 #endif
 
-static unsigned int rates[] = { 5512, 8000, 11025, 16000, 22050, 32000, 44100,
-                                 48000, 64000, 88200, 96000, 176400, 192000 };
+static unsigned int rates[] = { 5512, 8000, 11025, 12000, 16000, 22050, 24000, 
+				32000, 44100, 48000, 64000, 88200, 96000, 
+				176400, 192000 };
 
 const struct snd_pcm_hw_constraint_list snd_pcm_known_rates = {
 	.count = ARRAY_SIZE(rates),
@@ -1772,9 +1773,17 @@
 				struct snd_pcm_hw_rule *rule)
 {
 	struct snd_pcm_hardware *hw = rule->private;
+#if 0
 	return snd_interval_list(hw_param_interval(params, rule->var),
 				 snd_pcm_known_rates.count,
 				 snd_pcm_known_rates.list, hw->rates);
+#else
+	//printk("hw->rates=0x%08x\n",hw->rates);//0x3b6
+	hw->rates = 0x3fe;//12KHz and 24KHz bits are all zero,you need set 1
+	return snd_interval_list(hw_param_interval(params, rule->var),
+				 snd_pcm_known_rates.count,
+				 snd_pcm_known_rates.list, hw->rates);
+#endif
 }		
 
 static int snd_pcm_hw_rule_buffer_bytes_max(struct snd_pcm_hw_params *params,
diff -ru linux-2.6/sound/soc/codecs/Kconfig /plain/src/qi/linux-2.6.27.git.svn/sound/soc/codecs/Kconfig
--- linux-2.6/sound/soc/codecs/Kconfig	2009-08-17 23:58:04.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/sound/soc/codecs/Kconfig	2009-08-12 10:39:09.000000000 +0200
@@ -50,3 +50,15 @@
 config SND_SOC_TLV320AIC3X
 	tristate
 	depends on I2C
+
+config SND_SOC_ICODEC
+	tristate "Jz4740 internal codec"
+	depends on SND_SOC && SND_JZ4740_SOC_PAVO && SND_JZ4740_SOC_I2S
+	help
+	  Say Y if you want to use internal codec on Ingenic Jz4740 PAVO board.
+
+config SND_SOC_DLV
+	tristate "Jz4750 internal codec"
+	depends on SND_SOC && SND_JZ4750_SOC_APUS && SND_JZ4750_SOC_I2S
+	help
+	  Say Y if you want to use internal codec on Ingenic Jz4750 APUS board.
\ No newline at end of file
diff -ru linux-2.6/sound/soc/codecs/Makefile /plain/src/qi/linux-2.6.27.git.svn/sound/soc/codecs/Makefile
--- linux-2.6/sound/soc/codecs/Makefile	2009-08-17 23:58:04.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/sound/soc/codecs/Makefile	2009-08-12 10:39:09.000000000 +0200
@@ -10,6 +10,8 @@
 snd-soc-wm9713-objs := wm9713.o
 snd-soc-cs4270-objs := cs4270.o
 snd-soc-tlv320aic3x-objs := tlv320aic3x.o
+snd-soc-jzcodec-objs := jzcodec.o
+snd-soc-jzdlv-objs := jzdlv.o
 
 obj-$(CONFIG_SND_SOC_AC97_CODEC)	+= snd-soc-ac97.o
 obj-$(CONFIG_SND_SOC_AK4535)	+= snd-soc-ak4535.o
@@ -23,3 +25,5 @@
 obj-$(CONFIG_SND_SOC_WM9713)	+= snd-soc-wm9713.o
 obj-$(CONFIG_SND_SOC_CS4270)	+= snd-soc-cs4270.o
 obj-$(CONFIG_SND_SOC_TLV320AIC3X)	+= snd-soc-tlv320aic3x.o
+obj-$(CONFIG_SND_SOC_ICODEC)	+= snd-soc-jzcodec.o
+obj-$(CONFIG_SND_SOC_DLV)	+= snd-soc-jzdlv.o
\ No newline at end of file
diff -ru linux-2.6/sound/soc/Kconfig /plain/src/qi/linux-2.6.27.git.svn/sound/soc/Kconfig
--- linux-2.6/sound/soc/Kconfig	2009-08-17 23:58:04.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/sound/soc/Kconfig	2009-08-12 10:39:09.000000000 +0200
@@ -31,6 +31,8 @@
 source "sound/soc/fsl/Kconfig"
 source "sound/soc/davinci/Kconfig"
 source "sound/soc/omap/Kconfig"
+source "sound/soc/jz4740/Kconfig"
+source "sound/soc/jz4750/Kconfig"
 
 # Supported codecs
 source "sound/soc/codecs/Kconfig"
diff -ru linux-2.6/sound/soc/Makefile /plain/src/qi/linux-2.6.27.git.svn/sound/soc/Makefile
--- linux-2.6/sound/soc/Makefile	2009-08-17 23:58:04.000000000 +0200
+++ /plain/src/qi/linux-2.6.27.git.svn/sound/soc/Makefile	2009-08-12 10:39:09.000000000 +0200
@@ -2,4 +2,4 @@
 
 obj-$(CONFIG_SND_SOC)	+= snd-soc-core.o
 obj-$(CONFIG_SND_SOC)	+= codecs/ at32/ at91/ pxa/ s3c24xx/ sh/ fsl/ davinci/
-obj-$(CONFIG_SND_SOC)	+= omap/ au1x/
+obj-$(CONFIG_SND_SOC)	+= omap/ au1x/ jz4740/ jz4750/