mirror of
git://projects.qi-hardware.com/openwrt-xburst.git
synced 2025-04-14 18:07:27 +03:00
128434cb23
This is the bcm57xx package. I have tested default vlan functions, but I dont have the equipment to test more advanced setups. The default vlan setup seems to be working fine. I also added the activate_gpio parameter which will make the driver activate the switch via gpio before probing for it. I'm not sure which method is best for autoload. For the wrt350n, I need the activate_gpio parameter. But its probably not a good idea to add that to the autoload file. On a system without a bcm57xx switch, isn't it a bad idea to mess with the gpios looking for the switch? Ideally, wouldn't it be best to load the bcm57xx module from broadcom-diag, after it has determined which router its on? I tried using 'request_module' from there, but had no success. For now, I am relying on preinit to load the bcm57xx module with activate_gpio param, after it has failed to load switch_robo and switch_adm. Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11471 3c298f89-4303-0410-b956-a3cf2f4a3e73
53 lines
1.4 KiB
C
53 lines
1.4 KiB
C
/*
|
|
* 802.1Q VLAN protocol definitions
|
|
*
|
|
* Copyright 2007, Broadcom Corporation
|
|
* All Rights Reserved.
|
|
*
|
|
* THIS SOFTWARE IS OFFERED "AS IS", AND BROADCOM GRANTS NO WARRANTIES OF ANY
|
|
* KIND, EXPRESS OR IMPLIED, BY STATUTE, COMMUNICATION OR OTHERWISE. BROADCOM
|
|
* SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
|
|
* FOR A SPECIFIC PURPOSE OR NONINFRINGEMENT CONCERNING THIS SOFTWARE.
|
|
*
|
|
* $Id: vlan.h,v 1.1.1.4 2007/05/31 08:00:41 michael Exp $
|
|
*/
|
|
|
|
#ifndef _vlan_h_
|
|
#define _vlan_h_
|
|
|
|
/* enable structure packing */
|
|
#if defined(__GNUC__)
|
|
#define PACKED __attribute__((packed))
|
|
#else
|
|
#pragma pack(1)
|
|
#define PACKED
|
|
#endif
|
|
|
|
#define VLAN_VID_MASK 0xfff /* low 12 bits are vlan id */
|
|
#define VLAN_CFI_SHIFT 12 /* canonical format indicator bit */
|
|
#define VLAN_PRI_SHIFT 13 /* user priority */
|
|
|
|
#define VLAN_PRI_MASK 7 /* 3 bits of priority */
|
|
|
|
#define VLAN_TAG_LEN 4
|
|
#define VLAN_TAG_OFFSET (2 * ETHER_ADDR_LEN) /* offset in Ethernet II packet only */
|
|
|
|
#define VLAN_TPID 0x8100 /* VLAN ethertype/Tag Protocol ID */
|
|
|
|
struct ethervlan_header {
|
|
uint8 ether_dhost[ETHER_ADDR_LEN];
|
|
uint8 ether_shost[ETHER_ADDR_LEN];
|
|
uint16 vlan_type; /* 0x8100 */
|
|
uint16 vlan_tag; /* priority, cfi and vid */
|
|
uint16 ether_type;
|
|
};
|
|
|
|
#define ETHERVLAN_HDR_LEN (ETHER_HDR_LEN + VLAN_TAG_LEN)
|
|
|
|
#undef PACKED
|
|
#if !defined(__GNUC__)
|
|
#pragma pack()
|
|
#endif
|
|
|
|
#endif /* _vlan_h_ */
|