qi-hardware/openwrt-xburst
1
0
Fork 0
mirror of git://projects.qi-hardware.com/openwrt-xburst.git synced 2024-12-01 08:48:25 +02:00
Code
312e64a8db
openwrt-xburst/target/linux/at91/image/u-boot/patches/100-netusg20.patch
claudio 8d879e2449 [at91] Add support for u-boot 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22351 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-07-22 11:32:38 +00:00

575 lines
17 KiB
Diff
Raw Blame History

Add support for the NetusG20 board by Acmesystems srl.
This board is based on AT91SAM9G20 SoC.
Signed-off-by: Claudio Mignanti <c.mignanti@gmail.com>
---
MAKEALL | 1 +
Makefile | 3 +
arch/arm/cpu/arm926ejs/at91/at91sam9260_devices.c | 5 +
board/acmesystems/netusg20/Makefile | 56 +++++++
board/acmesystems/netusg20/config.mk | 1 +
board/acmesystems/netusg20/led.c | 40 +++++
board/acmesystems/netusg20/netusg20.c | 152 +++++++++++++++++
board/acmesystems/netusg20/partition.c | 39 +++++
include/configs/netusg20.h | 181 +++++++++++++++++++++
9 files changed, 478 insertions(+), 0 deletions(-)
create mode 100644 board/acmesystems/netusg20/Makefile
create mode 100644 board/acmesystems/netusg20/config.mk
create mode 100644 board/acmesystems/netusg20/led.c
create mode 100644 board/acmesystems/netusg20/netusg20.c
create mode 100644 board/acmesystems/netusg20/partition.c
create mode 100644 include/configs/netusg20.h
diff --git a/MAKEALL b/MAKEALL
index d6d5f5b..60e36e1 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -684,6 +684,7 @@ LIST_at91=" \
meesc \
mp2usb \
m501sk \
+ netusg20 \
otc570 \
pm9261 \
pm9263 \
diff --git a/Makefile b/Makefile
index 87d5214..b73659f 100644
--- a/Makefile
+++ b/Makefile
@@ -2867,6 +2867,9 @@ at91sam9g45ekes_config : unconfig
fi;
@$(MKCONFIG) -a at91sam9m10g45ek arm arm926ejs at91sam9m10g45ek atmel at91
+netusg20_config: unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm926ejs netusg20 acmesystems at91
+
otc570_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm926ejs otc570 esd at91
diff --git a/arch/arm/cpu/arm926ejs/at91/at91sam9260_devices.c b/arch/arm/cpu/arm926ejs/at91/at91sam9260_devices.c
index 77d49ab..87ec531 100644
--- a/arch/arm/cpu/arm926ejs/at91/at91sam9260_devices.c
+++ b/arch/arm/cpu/arm926ejs/at91/at91sam9260_devices.c
@@ -59,7 +59,12 @@ void at91_serial3_hw_init(void)
{
at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE;
+#ifdef CONFIG_NETUSG20
+ /* pull-up active on DRXD*/
+ at91_set_a_periph(AT91_PIO_PORTB, 14, 1);
+#else
at91_set_a_periph(AT91_PIO_PORTB, 14, 0); /* DRXD */
+#endif
at91_set_a_periph(AT91_PIO_PORTB, 15, 1); /* DTXD */
writel(1 << AT91_ID_SYS, &pmc->pcer);
}
diff --git a/board/acmesystems/netusg20/Makefile b/board/acmesystems/netusg20/Makefile
new file mode 100644
index 0000000..31589fd
--- /dev/null
+++ b/board/acmesystems/netusg20/Makefile
@@ -0,0 +1,56 @@
+#
+# (C) Copyright 2003-2008
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# (C) Copyright 2008
+# Stelian Pop <stelian.pop@leadtechdesign.com>
+# Lead Tech Design <www.leadtechdesign.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS-y += netusg20.o
+COBJS-y += led.o
+COBJS-y += partition.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS-y))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/acmesystems/netusg20/config.mk b/board/acmesystems/netusg20/config.mk
new file mode 100644
index 0000000..ff2cfd1
--- /dev/null
+++ b/board/acmesystems/netusg20/config.mk
@@ -0,0 +1 @@
+TEXT_BASE = 0x23f00000
diff --git a/board/acmesystems/netusg20/led.c b/board/acmesystems/netusg20/led.c
new file mode 100644
index 0000000..1016b98
--- /dev/null
+++ b/board/acmesystems/netusg20/led.c
@@ -0,0 +1,40 @@
+/*
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian.pop@leadtechdesign.com>
+ * Lead Tech Design <www.leadtechdesign.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/at91sam9260.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/io.h>
+
+
+void coloured_LED_init(void)
+{
+ /* Enable clock */
+ at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9260_ID_PIOA);
+
+ at91_set_gpio_output(CONFIG_RED_LED, 1);
+
+ at91_set_gpio_value(CONFIG_RED_LED, 1);
+}
diff --git a/board/acmesystems/netusg20/netusg20.c b/board/acmesystems/netusg20/netusg20.c
new file mode 100644
index 0000000..94b4d4c
--- /dev/null
+++ b/board/acmesystems/netusg20/netusg20.c
@@ -0,0 +1,152 @@
+/*
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian.pop@leadtechdesign.com>
+ * Lead Tech Design <www.leadtechdesign.com>
+ *
+ * (C) Copyright 2010
+ * Claudio Mignanti <c.mignanti@gmail.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/at91sam9260.h>
+#include <asm/arch/at91sam9260_matrix.h>
+#include <asm/arch/at91sam9_smc.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_rstc.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/io.h>
+#include <asm/arch/hardware.h>
+#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
+#include <net.h>
+#endif
+#include <netdev.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* ------------------------------------------------------------------------- */
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+
+#ifdef CONFIG_MACB
+static void at91sam9260ek_macb_hw_init(void)
+{
+ unsigned long rstc;
+
+ /* Enable clock */
+ at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9260_ID_EMAC);
+
+ /*
+ * Disable pull-up on:
+ * RXDV (PA17) => PHY normal mode (not Test mode)
+ * ERX0 (PA14) => PHY ADDR0
+ * ERX1 (PA15) => PHY ADDR1
+ * ERX2 (PA25) => PHY ADDR2
+ * ERX3 (PA26) => PHY ADDR3
+ * ECRS (PA28) => PHY ADDR4 => PHYADDR = 0x0
+ *
+ * PHY has internal pull-down
+ */
+ writel(pin_to_mask(AT91_PIN_PA14) |
+ pin_to_mask(AT91_PIN_PA15) |
+ pin_to_mask(AT91_PIN_PA17) |
+ pin_to_mask(AT91_PIN_PA25) |
+ pin_to_mask(AT91_PIN_PA26) |
+ pin_to_mask(AT91_PIN_PA28),
+ pin_to_controller(AT91_PIN_PA0) + PIO_PUDR);
+
+ rstc = at91_sys_read(AT91_RSTC_MR) & AT91_RSTC_ERSTL;
+
+ at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_EXTRST);
+
+ /* Wait for end hardware reset */
+ while (!(at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_NRSTL));
+
+ /* Restore NRST value */
+ at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
+ (rstc) |
+ AT91_RSTC_URSTEN);
+
+ /* Re-enable pull-up */
+ writel(pin_to_mask(AT91_PIN_PA14) |
+ pin_to_mask(AT91_PIN_PA15) |
+ pin_to_mask(AT91_PIN_PA17) |
+ pin_to_mask(AT91_PIN_PA25) |
+ pin_to_mask(AT91_PIN_PA26) |
+ pin_to_mask(AT91_PIN_PA28),
+ pin_to_controller(AT91_PIN_PA0) + PIO_PUER);
+
+ at91_macb_hw_init();
+}
+#endif
+
+int board_init(void)
+{
+ /* Enable Ctrlc */
+ console_init_f();
+
+ gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G20EK;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+ at91_serial_hw_init();
+#ifdef CONFIG_HAS_DATAFLASH
+ at91_spi0_hw_init((1 << 0) | (1 << 1));
+#endif
+#ifdef CONFIG_MACB
+ at91sam9260ek_macb_hw_init();
+#endif
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+void reset_phy(void)
+{
+#ifdef CONFIG_MACB
+ /*
+ * Initialize ethernet HW addr prior to starting Linux,
+ * needed for nfsroot
+ */
+ eth_init(gd->bd);
+#endif
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+ int rc = 0;
+#ifdef CONFIG_MACB
+ rc = macb_eth_initialize(0, (void *)AT91SAM9260_BASE_EMAC, 0x00);
+#endif
+ return rc;
+}
+
+void show_boot_progress (int val){}
diff --git a/board/acmesystems/netusg20/partition.c b/board/acmesystems/netusg20/partition.c
new file mode 100644
index 0000000..7d79e53
--- /dev/null
+++ b/board/acmesystems/netusg20/partition.c
@@ -0,0 +1,39 @@
+/*
+ * (C) Copyright 2008
+ * Ulf Samuelsson <ulf@atmel.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+#include <common.h>
+#include <config.h>
+#include <asm/hardware.h>
+#include <dataflash.h>
+
+AT91S_DATAFLASH_INFO dataflash_info[CONFIG_SYS_MAX_DATAFLASH_BANKS];
+
+struct dataflash_addr cs[CONFIG_SYS_MAX_DATAFLASH_BANKS] = {
+ {CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1, 1}
+};
+
+/*define the area offsets*/
+dataflash_protect_t area_list[NB_DATAFLASH_AREA] = {
+ {0x00000000, 0x000041FF, FLAG_PROTECT_SET, 0, "Bootstrap"},
+ {0x00004200, 0x000083FF, FLAG_PROTECT_CLEAR, 0, "Environment"},
+ {0x00008400, 0x00041FFF, FLAG_PROTECT_SET, 0, "U-Boot"},
+ {0x00042000, 0x00251FFF, FLAG_PROTECT_CLEAR, 0, "Kernel"},
+ {0x00252000, 0xFFFFFFFF, FLAG_PROTECT_CLEAR, 0, "FS"},
+};
diff --git a/include/configs/netusg20.h b/include/configs/netusg20.h
new file mode 100644
index 0000000..99b4f12
--- /dev/null
+++ b/include/configs/netusg20.h
@@ -0,0 +1,181 @@
+/*
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian.pop@leadtechdesign.com>
+ * Lead Tech Design <www.leadtechdesign.com>
+ *
+ * Configuation settings for the NetusG20 boards.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_AT91_LEGACY
+
+/* ARM asynchronous clock */
+#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* 18.432 MHz crystal */
+#define CONFIG_SYS_HZ 1000
+
+#define CONFIG_DISPLAY_CPUINFO
+
+#define CONFIG_ARM926EJS 1 /* This is an ARM926EJS Core */
+#define CONFIG_AT91SAM9G20 1 /* It's an Atmel AT91SAM9G20 SoC*/
+#define CONFIG_NETUSG20 1
+
+#define CONFIG_ARCH_CPU_INIT
+#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
+
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_INITRD_TAG 1
+
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_SKIP_RELOCATE_UBOOT
+
+/*
+ * Hardware drivers
+ */
+#define CONFIG_AT91_GPIO 1
+#define CONFIG_ATMEL_USART 1
+#undef CONFIG_USART0
+#undef CONFIG_USART1
+#undef CONFIG_USART2
+#define CONFIG_USART3 1 /* USART 3 is DBGU */
+
+/* LED */
+#define CONFIG_AT91_LED
+#define CONFIG_RED_LED AT91_PIN_PA9 /* this is the power led */
+#define CONFIG_GREEN_LED AT91_PIN_PA6 /* this is the user led */
+
+#define CONFIG_BOOTDELAY 3
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE 1
+#define CONFIG_BOOTP_BOOTPATH 1
+#define CONFIG_BOOTP_GATEWAY 1
+#define CONFIG_BOOTP_HOSTNAME 1
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_BDI
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_IMI
+#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_SOURCE
+
+#define CONFIG_CMD_PING 1
+#define CONFIG_CMD_DHCP 1
+#define CONFIG_CMD_USB 1
+
+/* SDRAM */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM 0x20000000
+#define PHYS_SDRAM_SIZE 0x04000000 /* 64 megs */
+
+/* DataFlash */
+#define CONFIG_ATMEL_DATAFLASH_SPI
+#define CONFIG_HAS_DATAFLASH 1
+#define CONFIG_SYS_SPI_WRITE_TOUT (5*CONFIG_SYS_HZ)
+#define CONFIG_SYS_MAX_DATAFLASH_BANKS 1
+#define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1 0xD0000000 /* CS1 */
+#define AT91_SPI_CLK 15000000
+
+#define DATAFLASH_TCSS (0x22 << 16)
+#define DATAFLASH_TCHS (0x1 << 24)
+
+/* no NAND flash on this board*/
+#define CONFIG_SYS_NO_FLASH
+
+/* Ethernet */
+#define CONFIG_MACB 1
+#define CONFIG_RMII 1
+#define CONFIG_NET_MULTI 1
+#define CONFIG_NET_RETRY_COUNT 20
+#define CONFIG_RESET_PHY_R 1
+
+/* MMC */
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_ATMEL_MCI
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_IMI
+#define CONFIG_CMD_SOURCE
+
+#define MMCI_BASE 0xFFFA8000
+
+/* USB */
+#define CONFIG_USB_ATMEL
+#define CONFIG_USB_OHCI_NEW 1
+#define CONFIG_DOS_PARTITION 1
+#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
+#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00500000 /* AT91SAM9260_UHP_BASE */
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
+#define CONFIG_USB_STORAGE 1
+
+#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
+
+#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
+#define CONFIG_SYS_MEMTEST_END 0x23e00000
+
+/* Filesystem */
+#define CONFIG_CMD_FAT 1
+#define CONFIG_CMD_EXT2 1
+
+/* bootstrap + u-boot + env + linux in dataflash on CS1 */
+#define CONFIG_ENV_IS_IN_DATAFLASH 1
+#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1 + 0x8400)
+#define CONFIG_ENV_OFFSET 0x4200
+#define CONFIG_ENV_ADDR (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1 + CONFIG_ENV_OFFSET)
+#define CONFIG_ENV_SIZE 0x4200
+#define CONFIG_BOOTCOMMAND "mmc init; sleep 1; " \
+ "ext2load mmc 0 0x20000000 uImage; " \
+ "source 0x20000000"
+#define CONFIG_BOOTARGS "mem=64M console=ttyS0,115200 " \
+ "root=/dev/mmcblk0p1 rootwait"
+
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 }
+
+#define CONFIG_SYS_PROMPT "U-Boot> "
+#define CONFIG_SYS_CBSIZE 256
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_LONGHELP 1
+#define CONFIG_CMDLINE_EDITING 1
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* 128 bytes for initial data */
+
+#define CONFIG_STACKSIZE (32*1024) /* regular stack */
+
+#ifdef CONFIG_USE_IRQ
+#error CONFIG_USE_IRQ not supported
+#endif
+
+#endif
--
1.7.0.4
View Git Blame Copy Permalink