mirror of
git://projects.qi-hardware.com/openwrt-xburst.git
synced 2024-09-12 23:24:37 +03:00
This is the bcm57xx package. I have tested default vlan functions, but I dont have the equipment to test more advanced setups. The default vlan setup seems to be working fine. I also added the activate_gpio parameter which will make the driver activate the switch via gpio before probing for it. I'm not sure which method is best for autoload. For the wrt350n, I need the activate_gpio parameter. But its probably not a good idea to add that to the autoload file. On a system without a bcm57xx switch, isn't it a bad idea to mess with the gpios looking for the switch? Ideally, wouldn't it be best to load the bcm57xx module from broadcom-diag, after it has determined which router its on? I tried using 'request_module' from there, but had no success. For now, I am relying on preinit to load the bcm57xx module with activate_gpio param, after it has failed to load switch_robo and switch_adm. Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11471 3c298f89-4303-0410-b956-a3cf2f4a3e73
47 lines
1.9 KiB
C
47 lines
1.9 KiB
C
/******************************************************************************/
|
|
/* */
|
|
/* Broadcom BCM5700 Linux Network Driver, Copyright (c) 2000 - 2004 Broadcom */
|
|
/* Corporation. */
|
|
/* All rights reserved. */
|
|
/* */
|
|
/* This program is free software; you can redistribute it and/or modify */
|
|
/* it under the terms of the GNU General Public License as published by */
|
|
/* the Free Software Foundation, located in the file LICENSE. */
|
|
/* */
|
|
/* History: */
|
|
/* */
|
|
/******************************************************************************/
|
|
|
|
#ifdef INCLUDE_5701_AX_FIX
|
|
|
|
#include "mm.h"
|
|
#include "5701rls.h"
|
|
|
|
LM_STATUS LM_LoadRlsFirmware(PLM_DEVICE_BLOCK pDevice)
|
|
{
|
|
T3_FWIMG_INFO FwImgInfo;
|
|
|
|
FwImgInfo.StartAddress = t3FwStartAddr;
|
|
FwImgInfo.Text.Buffer = (PLM_UINT8)t3FwText;
|
|
FwImgInfo.Text.Offset = t3FwTextAddr;
|
|
FwImgInfo.Text.Length = t3FwTextLen;
|
|
FwImgInfo.ROnlyData.Buffer = (PLM_UINT8)t3FwRodata;
|
|
FwImgInfo.ROnlyData.Offset = t3FwRodataAddr;
|
|
FwImgInfo.ROnlyData.Length = t3FwRodataLen;
|
|
FwImgInfo.Data.Buffer = (PLM_UINT8)t3FwData;
|
|
FwImgInfo.Data.Offset = t3FwDataAddr;
|
|
FwImgInfo.Data.Length = t3FwDataLen;
|
|
|
|
if (LM_LoadFirmware(pDevice,
|
|
&FwImgInfo,
|
|
T3_RX_CPU_ID | T3_TX_CPU_ID,
|
|
T3_RX_CPU_ID) != LM_STATUS_SUCCESS)
|
|
{
|
|
return LM_STATUS_FAILURE;
|
|
}
|
|
|
|
return LM_STATUS_SUCCESS;
|
|
}
|
|
|
|
#endif /* INCLUDE_5701_AX_FIX */
|