qi-hardware/openwrt-xburst
1
0
Fork 0
mirror of git://projects.qi-hardware.com/openwrt-xburst.git synced 2024-12-11 20:40:37 +02:00
Code
c766a7bd69
openwrt-xburst/target/linux/generic/patches-2.6.33/975-ssb_update.patch
hauke dede4b7a95 kernel: fix some mistakes in ssb patch refresh in r22766, r22767 and r22768. 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22774 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-08-22 19:22:01 +00:00

534 lines
25 KiB
Diff
Raw Blame History

--- a/drivers/ssb/driver_chipcommon.c
+++ b/drivers/ssb/driver_chipcommon.c
@@ -373,6 +373,7 @@ u32 ssb_chipco_gpio_control(struct ssb_c
{
return chipco_write32_masked(cc, SSB_CHIPCO_GPIOCTL, mask, value);
}
+EXPORT_SYMBOL(ssb_chipco_gpio_control);
u32 ssb_chipco_gpio_intmask(struct ssb_chipcommon *cc, u32 mask, u32 value)
{
--- a/drivers/ssb/driver_chipcommon_pmu.c
+++ b/drivers/ssb/driver_chipcommon_pmu.c
@@ -332,6 +332,12 @@ static void ssb_pmu_pll_init(struct ssb_
case 0x5354:
ssb_pmu0_pllinit_r0(cc, crystalfreq);
break;
+ case 0x4322:
+ if (cc->pmu.rev == 2) {
+ chipco_write32(cc, SSB_CHIPCO_PLLCTL_ADDR, 0x0000000A);
+ chipco_write32(cc, SSB_CHIPCO_PLLCTL_DATA, 0x380005C0);
+ }
+ break;
default:
ssb_printk(KERN_ERR PFX
"ERROR: PLL init unknown for device %04X\n",
@@ -417,6 +423,7 @@ static void ssb_pmu_resources_init(struc
switch (bus->chip_id) {
case 0x4312:
+ case 0x4322:
/* We keep the default settings:
* min_msk = 0xCBB
* max_msk = 0x7FFFF
--- a/drivers/ssb/driver_mipscore.c
+++ b/drivers/ssb/driver_mipscore.c
@@ -270,7 +270,6 @@ void ssb_mipscore_init(struct ssb_mipsco
set_irq(dev, irq++);
}
break;
- /* fallthrough */
case SSB_DEV_PCI:
case SSB_DEV_ETHERNET:
case SSB_DEV_ETHERNET_GBIT:
@@ -281,6 +280,10 @@ void ssb_mipscore_init(struct ssb_mipsco
set_irq(dev, irq++);
break;
}
+ /* fallthrough */
+ case SSB_DEV_EXTIF:
+ set_irq(dev, 0);
+ break;
}
}
ssb_dprintk(KERN_INFO PFX "after irq reconfiguration\n");
--- a/drivers/ssb/driver_pcicore.c
+++ b/drivers/ssb/driver_pcicore.c
@@ -246,20 +246,12 @@ static struct pci_controller ssb_pcicore
.pci_ops = &ssb_pcicore_pciops,
.io_resource = &ssb_pcicore_io_resource,
.mem_resource = &ssb_pcicore_mem_resource,
- .mem_offset = 0x24000000,
};
-static u32 ssb_pcicore_pcibus_iobase = 0x100;
-static u32 ssb_pcicore_pcibus_membase = SSB_PCI_DMA;
-
/* This function is called when doing a pci_enable_device().
* We must first check if the device is a device on the PCI-core bridge. */
int ssb_pcicore_plat_dev_init(struct pci_dev *d)
{
- struct resource *res;
- int pos, size;
- u32 *base;
-
if (d->bus->ops != &ssb_pcicore_pciops) {
/* This is not a device on the PCI-core bridge. */
return -ENODEV;
@@ -268,27 +260,6 @@ int ssb_pcicore_plat_dev_init(struct pci
ssb_printk(KERN_INFO "PCI: Fixing up device %s\n",
pci_name(d));
- /* Fix up resource bases */
- for (pos = 0; pos < 6; pos++) {
- res = &d->resource[pos];
- if (res->flags & IORESOURCE_IO)
- base = &ssb_pcicore_pcibus_iobase;
- else
- base = &ssb_pcicore_pcibus_membase;
- res->flags |= IORESOURCE_PCI_FIXED;
- if (res->end) {
- size = res->end - res->start + 1;
- if (*base & (size - 1))
- *base = (*base + size) & ~(size - 1);
- res->start = *base;
- res->end = res->start + size - 1;
- *base += size;
- pci_write_config_dword(d, PCI_BASE_ADDRESS_0 + (pos << 2), res->start);
- }
- /* Fix up PCI bridge BAR0 only */
- if (d->bus->number == 0 && PCI_SLOT(d->devfn) == 0)
- break;
- }
/* Fix up interrupt lines */
d->irq = ssb_mips_irq(extpci_core->dev) + 2;
pci_write_config_byte(d, PCI_INTERRUPT_LINE, d->irq);
--- a/drivers/ssb/main.c
+++ b/drivers/ssb/main.c
@@ -833,6 +833,9 @@ int ssb_bus_pcibus_register(struct ssb_b
if (!err) {
ssb_printk(KERN_INFO PFX "Sonics Silicon Backplane found on "
"PCI device %s\n", dev_name(&host_pci->dev));
+ } else {
+ ssb_printk(KERN_ERR PFX "Failed to register PCI version"
+ " of SSB with error %d\n", err);
}
return err;
--- a/drivers/ssb/ssb_private.h
+++ b/drivers/ssb/ssb_private.h
@@ -196,7 +196,7 @@ extern int ssb_devices_thaw(struct ssb_f
#ifdef CONFIG_SSB_B43_PCI_BRIDGE
extern int __init b43_pci_ssb_bridge_init(void);
extern void __exit b43_pci_ssb_bridge_exit(void);
-#else /* CONFIG_SSB_B43_PCI_BRIDGR */
+#else /* CONFIG_SSB_B43_PCI_BRIDGE */
static inline int b43_pci_ssb_bridge_init(void)
{
return 0;
@@ -204,6 +204,6 @@ static inline int b43_pci_ssb_bridge_ini
static inline void b43_pci_ssb_bridge_exit(void)
{
}
-#endif /* CONFIG_SSB_PCIHOST */
+#endif /* CONFIG_SSB_B43_PCI_BRIDGE */
#endif /* LINUX_SSB_PRIVATE_H_ */
--- a/include/linux/ssb/ssb_driver_chipcommon.h
+++ b/include/linux/ssb/ssb_driver_chipcommon.h
@@ -54,6 +54,7 @@
#define SSB_CHIPCO_CAP_64BIT 0x08000000 /* 64-bit Backplane */
#define SSB_CHIPCO_CAP_PMU 0x10000000 /* PMU available (rev >= 20) */
#define SSB_CHIPCO_CAP_ECI 0x20000000 /* ECI available (rev >= 20) */
+#define SSB_CHIPCO_CAP_SPROM 0x40000000 /* SPROM present */
#define SSB_CHIPCO_CORECTL 0x0008
#define SSB_CHIPCO_CORECTL_UARTCLK0 0x00000001 /* Drive UART with internal clock */
#define SSB_CHIPCO_CORECTL_SE 0x00000002 /* sync clk out enable (corerev >= 3) */
@@ -386,6 +387,7 @@
/** Chip specific Chip-Status register contents. */
+#define SSB_CHIPCO_CHST_4322_SPROM_EXISTS 0x00000040 /* SPROM present */
#define SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL 0x00000003
#define SSB_CHIPCO_CHST_4325_DEFCIS_SEL 0 /* OTP is powered up, use def. CIS, no SPROM */
#define SSB_CHIPCO_CHST_4325_SPROM_SEL 1 /* OTP is powered up, SPROM is present */
@@ -399,6 +401,18 @@
#define SSB_CHIPCO_CHST_4325_RCAL_VALUE_SHIFT 4
#define SSB_CHIPCO_CHST_4325_PMUTOP_2B 0x00000200 /* 1 for 2b, 0 for to 2a */
+/** Macros to determine SPROM presence based on Chip-Status register. */
+#define SSB_CHIPCO_CHST_4312_SPROM_PRESENT(status) \
+ ((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \
+ SSB_CHIPCO_CHST_4325_OTP_SEL)
+#define SSB_CHIPCO_CHST_4322_SPROM_PRESENT(status) \
+ (status & SSB_CHIPCO_CHST_4322_SPROM_EXISTS)
+#define SSB_CHIPCO_CHST_4325_SPROM_PRESENT(status) \
+ (((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \
+ SSB_CHIPCO_CHST_4325_DEFCIS_SEL) && \
+ ((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \
+ SSB_CHIPCO_CHST_4325_OTP_SEL))
+
/** Clockcontrol masks and values **/
--- a/include/linux/ssb/ssb_regs.h
+++ b/include/linux/ssb/ssb_regs.h
@@ -178,19 +178,19 @@
#define SSB_SPROM_REVISION_CRC_SHIFT 8
/* SPROM Revision 1 */
-#define SSB_SPROM1_SPID 0x1004 /* Subsystem Product ID for PCI */
-#define SSB_SPROM1_SVID 0x1006 /* Subsystem Vendor ID for PCI */
-#define SSB_SPROM1_PID 0x1008 /* Product ID for PCI */
-#define SSB_SPROM1_IL0MAC 0x1048 /* 6 bytes MAC address for 802.11b/g */
-#define SSB_SPROM1_ET0MAC 0x104E /* 6 bytes MAC address for Ethernet */
-#define SSB_SPROM1_ET1MAC 0x1054 /* 6 bytes MAC address for 802.11a */
-#define SSB_SPROM1_ETHPHY 0x105A /* Ethernet PHY settings */
+#define SSB_SPROM1_SPID 0x0004 /* Subsystem Product ID for PCI */
+#define SSB_SPROM1_SVID 0x0006 /* Subsystem Vendor ID for PCI */
+#define SSB_SPROM1_PID 0x0008 /* Product ID for PCI */
+#define SSB_SPROM1_IL0MAC 0x0048 /* 6 bytes MAC address for 802.11b/g */
+#define SSB_SPROM1_ET0MAC 0x004E /* 6 bytes MAC address for Ethernet */
+#define SSB_SPROM1_ET1MAC 0x0054 /* 6 bytes MAC address for 802.11a */
+#define SSB_SPROM1_ETHPHY 0x005A /* Ethernet PHY settings */
#define SSB_SPROM1_ETHPHY_ET0A 0x001F /* MII Address for enet0 */
#define SSB_SPROM1_ETHPHY_ET1A 0x03E0 /* MII Address for enet1 */
#define SSB_SPROM1_ETHPHY_ET1A_SHIFT 5
#define SSB_SPROM1_ETHPHY_ET0M (1<<14) /* MDIO for enet0 */
#define SSB_SPROM1_ETHPHY_ET1M (1<<15) /* MDIO for enet1 */
-#define SSB_SPROM1_BINF 0x105C /* Board info */
+#define SSB_SPROM1_BINF 0x005C /* Board info */
#define SSB_SPROM1_BINF_BREV 0x00FF /* Board Revision */
#define SSB_SPROM1_BINF_CCODE 0x0F00 /* Country Code */
#define SSB_SPROM1_BINF_CCODE_SHIFT 8
@@ -198,63 +198,63 @@
#define SSB_SPROM1_BINF_ANTBG_SHIFT 12
#define SSB_SPROM1_BINF_ANTA 0xC000 /* Available A-PHY antennas */
#define SSB_SPROM1_BINF_ANTA_SHIFT 14
-#define SSB_SPROM1_PA0B0 0x105E
-#define SSB_SPROM1_PA0B1 0x1060
-#define SSB_SPROM1_PA0B2 0x1062
-#define SSB_SPROM1_GPIOA 0x1064 /* General Purpose IO pins 0 and 1 */
+#define SSB_SPROM1_PA0B0 0x005E
+#define SSB_SPROM1_PA0B1 0x0060
+#define SSB_SPROM1_PA0B2 0x0062
+#define SSB_SPROM1_GPIOA 0x0064 /* General Purpose IO pins 0 and 1 */
#define SSB_SPROM1_GPIOA_P0 0x00FF /* Pin 0 */
#define SSB_SPROM1_GPIOA_P1 0xFF00 /* Pin 1 */
#define SSB_SPROM1_GPIOA_P1_SHIFT 8
-#define SSB_SPROM1_GPIOB 0x1066 /* General Purpuse IO pins 2 and 3 */
+#define SSB_SPROM1_GPIOB 0x0066 /* General Purpuse IO pins 2 and 3 */
#define SSB_SPROM1_GPIOB_P2 0x00FF /* Pin 2 */
#define SSB_SPROM1_GPIOB_P3 0xFF00 /* Pin 3 */
#define SSB_SPROM1_GPIOB_P3_SHIFT 8
-#define SSB_SPROM1_MAXPWR 0x1068 /* Power Amplifier Max Power */
+#define SSB_SPROM1_MAXPWR 0x0068 /* Power Amplifier Max Power */
#define SSB_SPROM1_MAXPWR_BG 0x00FF /* B-PHY and G-PHY (in dBm Q5.2) */
#define SSB_SPROM1_MAXPWR_A 0xFF00 /* A-PHY (in dBm Q5.2) */
#define SSB_SPROM1_MAXPWR_A_SHIFT 8
-#define SSB_SPROM1_PA1B0 0x106A
-#define SSB_SPROM1_PA1B1 0x106C
-#define SSB_SPROM1_PA1B2 0x106E
-#define SSB_SPROM1_ITSSI 0x1070 /* Idle TSSI Target */
+#define SSB_SPROM1_PA1B0 0x006A
+#define SSB_SPROM1_PA1B1 0x006C
+#define SSB_SPROM1_PA1B2 0x006E
+#define SSB_SPROM1_ITSSI 0x0070 /* Idle TSSI Target */
#define SSB_SPROM1_ITSSI_BG 0x00FF /* B-PHY and G-PHY*/
#define SSB_SPROM1_ITSSI_A 0xFF00 /* A-PHY */
#define SSB_SPROM1_ITSSI_A_SHIFT 8
-#define SSB_SPROM1_BFLLO 0x1072 /* Boardflags (low 16 bits) */
-#define SSB_SPROM1_AGAIN 0x1074 /* Antenna Gain (in dBm Q5.2) */
+#define SSB_SPROM1_BFLLO 0x0072 /* Boardflags (low 16 bits) */
+#define SSB_SPROM1_AGAIN 0x0074 /* Antenna Gain (in dBm Q5.2) */
#define SSB_SPROM1_AGAIN_BG 0x00FF /* B-PHY and G-PHY */
#define SSB_SPROM1_AGAIN_BG_SHIFT 0
#define SSB_SPROM1_AGAIN_A 0xFF00 /* A-PHY */
#define SSB_SPROM1_AGAIN_A_SHIFT 8
/* SPROM Revision 2 (inherits from rev 1) */
-#define SSB_SPROM2_BFLHI 0x1038 /* Boardflags (high 16 bits) */
-#define SSB_SPROM2_MAXP_A 0x103A /* A-PHY Max Power */
+#define SSB_SPROM2_BFLHI 0x0038 /* Boardflags (high 16 bits) */
+#define SSB_SPROM2_MAXP_A 0x003A /* A-PHY Max Power */
#define SSB_SPROM2_MAXP_A_HI 0x00FF /* Max Power High */
#define SSB_SPROM2_MAXP_A_LO 0xFF00 /* Max Power Low */
#define SSB_SPROM2_MAXP_A_LO_SHIFT 8
-#define SSB_SPROM2_PA1LOB0 0x103C /* A-PHY PowerAmplifier Low Settings */
-#define SSB_SPROM2_PA1LOB1 0x103E /* A-PHY PowerAmplifier Low Settings */
-#define SSB_SPROM2_PA1LOB2 0x1040 /* A-PHY PowerAmplifier Low Settings */
-#define SSB_SPROM2_PA1HIB0 0x1042 /* A-PHY PowerAmplifier High Settings */
-#define SSB_SPROM2_PA1HIB1 0x1044 /* A-PHY PowerAmplifier High Settings */
-#define SSB_SPROM2_PA1HIB2 0x1046 /* A-PHY PowerAmplifier High Settings */
-#define SSB_SPROM2_OPO 0x1078 /* OFDM Power Offset from CCK Level */
+#define SSB_SPROM2_PA1LOB0 0x003C /* A-PHY PowerAmplifier Low Settings */
+#define SSB_SPROM2_PA1LOB1 0x003E /* A-PHY PowerAmplifier Low Settings */
+#define SSB_SPROM2_PA1LOB2 0x0040 /* A-PHY PowerAmplifier Low Settings */
+#define SSB_SPROM2_PA1HIB0 0x0042 /* A-PHY PowerAmplifier High Settings */
+#define SSB_SPROM2_PA1HIB1 0x0044 /* A-PHY PowerAmplifier High Settings */
+#define SSB_SPROM2_PA1HIB2 0x0046 /* A-PHY PowerAmplifier High Settings */
+#define SSB_SPROM2_OPO 0x0078 /* OFDM Power Offset from CCK Level */
#define SSB_SPROM2_OPO_VALUE 0x00FF
#define SSB_SPROM2_OPO_UNUSED 0xFF00
-#define SSB_SPROM2_CCODE 0x107C /* Two char Country Code */
+#define SSB_SPROM2_CCODE 0x007C /* Two char Country Code */
/* SPROM Revision 3 (inherits most data from rev 2) */
-#define SSB_SPROM3_IL0MAC 0x104A /* 6 bytes MAC address for 802.11b/g */
-#define SSB_SPROM3_OFDMAPO 0x102C /* A-PHY OFDM Mid Power Offset (4 bytes, BigEndian) */
-#define SSB_SPROM3_OFDMALPO 0x1030 /* A-PHY OFDM Low Power Offset (4 bytes, BigEndian) */
-#define SSB_SPROM3_OFDMAHPO 0x1034 /* A-PHY OFDM High Power Offset (4 bytes, BigEndian) */
-#define SSB_SPROM3_GPIOLDC 0x1042 /* GPIO LED Powersave Duty Cycle (4 bytes, BigEndian) */
+#define SSB_SPROM3_OFDMAPO 0x002C /* A-PHY OFDM Mid Power Offset (4 bytes, BigEndian) */
+#define SSB_SPROM3_OFDMALPO 0x0030 /* A-PHY OFDM Low Power Offset (4 bytes, BigEndian) */
+#define SSB_SPROM3_OFDMAHPO 0x0034 /* A-PHY OFDM High Power Offset (4 bytes, BigEndian) */
+#define SSB_SPROM3_GPIOLDC 0x0042 /* GPIO LED Powersave Duty Cycle (4 bytes, BigEndian) */
#define SSB_SPROM3_GPIOLDC_OFF 0x0000FF00 /* Off Count */
#define SSB_SPROM3_GPIOLDC_OFF_SHIFT 8
#define SSB_SPROM3_GPIOLDC_ON 0x00FF0000 /* On Count */
#define SSB_SPROM3_GPIOLDC_ON_SHIFT 16
-#define SSB_SPROM3_CCKPO 0x1078 /* CCK Power Offset */
+#define SSB_SPROM3_IL0MAC 0x004A /* 6 bytes MAC address for 802.11b/g */
+#define SSB_SPROM3_CCKPO 0x0078 /* CCK Power Offset */
#define SSB_SPROM3_CCKPO_1M 0x000F /* 1M Rate PO */
#define SSB_SPROM3_CCKPO_2M 0x00F0 /* 2M Rate PO */
#define SSB_SPROM3_CCKPO_2M_SHIFT 4
@@ -265,100 +265,100 @@
#define SSB_SPROM3_OFDMGPO 0x107A /* G-PHY OFDM Power Offset (4 bytes, BigEndian) */
/* SPROM Revision 4 */
-#define SSB_SPROM4_IL0MAC 0x104C /* 6 byte MAC address for a/b/g/n */
-#define SSB_SPROM4_ETHPHY 0x105A /* Ethernet PHY settings ?? */
+#define SSB_SPROM4_BFLLO 0x0044 /* Boardflags (low 16 bits) */
+#define SSB_SPROM4_BFLHI 0x0046 /* Board Flags Hi */
+#define SSB_SPROM4_IL0MAC 0x004C /* 6 byte MAC address for a/b/g/n */
+#define SSB_SPROM4_CCODE 0x0052 /* Country Code (2 bytes) */
+#define SSB_SPROM4_GPIOA 0x0056 /* Gen. Purpose IO # 0 and 1 */
+#define SSB_SPROM4_GPIOA_P0 0x00FF /* Pin 0 */
+#define SSB_SPROM4_GPIOA_P1 0xFF00 /* Pin 1 */
+#define SSB_SPROM4_GPIOA_P1_SHIFT 8
+#define SSB_SPROM4_GPIOB 0x0058 /* Gen. Purpose IO # 2 and 3 */
+#define SSB_SPROM4_GPIOB_P2 0x00FF /* Pin 2 */
+#define SSB_SPROM4_GPIOB_P3 0xFF00 /* Pin 3 */
+#define SSB_SPROM4_GPIOB_P3_SHIFT 8
+#define SSB_SPROM4_ETHPHY 0x005A /* Ethernet PHY settings ?? */
#define SSB_SPROM4_ETHPHY_ET0A 0x001F /* MII Address for enet0 */
#define SSB_SPROM4_ETHPHY_ET1A 0x03E0 /* MII Address for enet1 */
#define SSB_SPROM4_ETHPHY_ET1A_SHIFT 5
#define SSB_SPROM4_ETHPHY_ET0M (1<<14) /* MDIO for enet0 */
#define SSB_SPROM4_ETHPHY_ET1M (1<<15) /* MDIO for enet1 */
-#define SSB_SPROM4_CCODE 0x1052 /* Country Code (2 bytes) */
-#define SSB_SPROM4_ANTAVAIL 0x105D /* Antenna available bitfields */
-#define SSB_SPROM4_ANTAVAIL_A 0x00FF /* A-PHY bitfield */
-#define SSB_SPROM4_ANTAVAIL_A_SHIFT 0
-#define SSB_SPROM4_ANTAVAIL_BG 0xFF00 /* B-PHY and G-PHY bitfield */
-#define SSB_SPROM4_ANTAVAIL_BG_SHIFT 8
-#define SSB_SPROM4_BFLLO 0x1044 /* Boardflags (low 16 bits) */
-#define SSB_SPROM4_AGAIN01 0x105E /* Antenna Gain (in dBm Q5.2) */
+#define SSB_SPROM4_ANTAVAIL 0x005D /* Antenna available bitfields */
+#define SSB_SPROM4_ANTAVAIL_A 0x00FF /* A-PHY bitfield */
+#define SSB_SPROM4_ANTAVAIL_A_SHIFT 0
+#define SSB_SPROM4_ANTAVAIL_BG 0xFF00 /* B-PHY and G-PHY bitfield */
+#define SSB_SPROM4_ANTAVAIL_BG_SHIFT 8
+#define SSB_SPROM4_AGAIN01 0x005E /* Antenna Gain (in dBm Q5.2) */
#define SSB_SPROM4_AGAIN0 0x00FF /* Antenna 0 */
#define SSB_SPROM4_AGAIN0_SHIFT 0
#define SSB_SPROM4_AGAIN1 0xFF00 /* Antenna 1 */
#define SSB_SPROM4_AGAIN1_SHIFT 8
-#define SSB_SPROM4_AGAIN23 0x1060
+#define SSB_SPROM4_AGAIN23 0x0060
#define SSB_SPROM4_AGAIN2 0x00FF /* Antenna 2 */
#define SSB_SPROM4_AGAIN2_SHIFT 0
#define SSB_SPROM4_AGAIN3 0xFF00 /* Antenna 3 */
#define SSB_SPROM4_AGAIN3_SHIFT 8
-#define SSB_SPROM4_BFLHI 0x1046 /* Board Flags Hi */
-#define SSB_SPROM4_MAXP_BG 0x1080 /* Max Power BG in path 1 */
+#define SSB_SPROM4_MAXP_BG 0x0080 /* Max Power BG in path 1 */
#define SSB_SPROM4_MAXP_BG_MASK 0x00FF /* Mask for Max Power BG */
#define SSB_SPROM4_ITSSI_BG 0xFF00 /* Mask for path 1 itssi_bg */
#define SSB_SPROM4_ITSSI_BG_SHIFT 8
-#define SSB_SPROM4_MAXP_A 0x108A /* Max Power A in path 1 */
+#define SSB_SPROM4_MAXP_A 0x008A /* Max Power A in path 1 */
#define SSB_SPROM4_MAXP_A_MASK 0x00FF /* Mask for Max Power A */
#define SSB_SPROM4_ITSSI_A 0xFF00 /* Mask for path 1 itssi_a */
#define SSB_SPROM4_ITSSI_A_SHIFT 8
-#define SSB_SPROM4_GPIOA 0x1056 /* Gen. Purpose IO # 0 and 1 */
-#define SSB_SPROM4_GPIOA_P0 0x00FF /* Pin 0 */
-#define SSB_SPROM4_GPIOA_P1 0xFF00 /* Pin 1 */
-#define SSB_SPROM4_GPIOA_P1_SHIFT 8
-#define SSB_SPROM4_GPIOB 0x1058 /* Gen. Purpose IO # 2 and 3 */
-#define SSB_SPROM4_GPIOB_P2 0x00FF /* Pin 2 */
-#define SSB_SPROM4_GPIOB_P3 0xFF00 /* Pin 3 */
-#define SSB_SPROM4_GPIOB_P3_SHIFT 8
-#define SSB_SPROM4_PA0B0 0x1082 /* The paXbY locations are */
-#define SSB_SPROM4_PA0B1 0x1084 /* only guesses */
-#define SSB_SPROM4_PA0B2 0x1086
-#define SSB_SPROM4_PA1B0 0x108E
-#define SSB_SPROM4_PA1B1 0x1090
-#define SSB_SPROM4_PA1B2 0x1092
+#define SSB_SPROM4_PA0B0 0x0082 /* The paXbY locations are */
+#define SSB_SPROM4_PA0B1 0x0084 /* only guesses */
+#define SSB_SPROM4_PA0B2 0x0086
+#define SSB_SPROM4_PA1B0 0x008E
+#define SSB_SPROM4_PA1B1 0x0090
+#define SSB_SPROM4_PA1B2 0x0092
/* SPROM Revision 5 (inherits most data from rev 4) */
-#define SSB_SPROM5_BFLLO 0x104A /* Boardflags (low 16 bits) */
-#define SSB_SPROM5_BFLHI 0x104C /* Board Flags Hi */
-#define SSB_SPROM5_IL0MAC 0x1052 /* 6 byte MAC address for a/b/g/n */
-#define SSB_SPROM5_CCODE 0x1044 /* Country Code (2 bytes) */
-#define SSB_SPROM5_GPIOA 0x1076 /* Gen. Purpose IO # 0 and 1 */
+#define SSB_SPROM5_CCODE 0x0044 /* Country Code (2 bytes) */
+#define SSB_SPROM5_BFLLO 0x004A /* Boardflags (low 16 bits) */
+#define SSB_SPROM5_BFLHI 0x004C /* Board Flags Hi */
+#define SSB_SPROM5_IL0MAC 0x0052 /* 6 byte MAC address for a/b/g/n */
+#define SSB_SPROM5_GPIOA 0x0076 /* Gen. Purpose IO # 0 and 1 */
#define SSB_SPROM5_GPIOA_P0 0x00FF /* Pin 0 */
#define SSB_SPROM5_GPIOA_P1 0xFF00 /* Pin 1 */
#define SSB_SPROM5_GPIOA_P1_SHIFT 8
-#define SSB_SPROM5_GPIOB 0x1078 /* Gen. Purpose IO # 2 and 3 */
+#define SSB_SPROM5_GPIOB 0x0078 /* Gen. Purpose IO # 2 and 3 */
#define SSB_SPROM5_GPIOB_P2 0x00FF /* Pin 2 */
#define SSB_SPROM5_GPIOB_P3 0xFF00 /* Pin 3 */
#define SSB_SPROM5_GPIOB_P3_SHIFT 8
/* SPROM Revision 8 */
-#define SSB_SPROM8_BOARDREV 0x1082 /* Board revision */
-#define SSB_SPROM8_BFLLO 0x1084 /* Board flags (bits 0-15) */
-#define SSB_SPROM8_BFLHI 0x1086 /* Board flags (bits 16-31) */
-#define SSB_SPROM8_BFL2LO 0x1088 /* Board flags (bits 32-47) */
-#define SSB_SPROM8_BFL2HI 0x108A /* Board flags (bits 48-63) */
-#define SSB_SPROM8_IL0MAC 0x108C /* 6 byte MAC address */
-#define SSB_SPROM8_CCODE 0x1092 /* 2 byte country code */
-#define SSB_SPROM8_ANTAVAIL 0x109C /* Antenna available bitfields*/
-#define SSB_SPROM8_ANTAVAIL_A 0xFF00 /* A-PHY bitfield */
-#define SSB_SPROM8_ANTAVAIL_A_SHIFT 8
-#define SSB_SPROM8_ANTAVAIL_BG 0x00FF /* B-PHY and G-PHY bitfield */
-#define SSB_SPROM8_ANTAVAIL_BG_SHIFT 0
-#define SSB_SPROM8_AGAIN01 0x109E /* Antenna Gain (in dBm Q5.2) */
+#define SSB_SPROM8_BOARDREV 0x0082 /* Board revision */
+#define SSB_SPROM8_BFLLO 0x0084 /* Board flags (bits 0-15) */
+#define SSB_SPROM8_BFLHI 0x0086 /* Board flags (bits 16-31) */
+#define SSB_SPROM8_BFL2LO 0x0088 /* Board flags (bits 32-47) */
+#define SSB_SPROM8_BFL2HI 0x008A /* Board flags (bits 48-63) */
+#define SSB_SPROM8_IL0MAC 0x008C /* 6 byte MAC address */
+#define SSB_SPROM8_CCODE 0x0092 /* 2 byte country code */
+#define SSB_SPROM8_GPIOA 0x0096 /*Gen. Purpose IO # 0 and 1 */
+#define SSB_SPROM8_GPIOA_P0 0x00FF /* Pin 0 */
+#define SSB_SPROM8_GPIOA_P1 0xFF00 /* Pin 1 */
+#define SSB_SPROM8_GPIOA_P1_SHIFT 8
+#define SSB_SPROM8_GPIOB 0x0098 /* Gen. Purpose IO # 2 and 3 */
+#define SSB_SPROM8_GPIOB_P2 0x00FF /* Pin 2 */
+#define SSB_SPROM8_GPIOB_P3 0xFF00 /* Pin 3 */
+#define SSB_SPROM8_GPIOB_P3_SHIFT 8
+#define SSB_SPROM8_ANTAVAIL 0x009C /* Antenna available bitfields*/
+#define SSB_SPROM8_ANTAVAIL_A 0xFF00 /* A-PHY bitfield */
+#define SSB_SPROM8_ANTAVAIL_A_SHIFT 8
+#define SSB_SPROM8_ANTAVAIL_BG 0x00FF /* B-PHY and G-PHY bitfield */
+#define SSB_SPROM8_ANTAVAIL_BG_SHIFT 0
+#define SSB_SPROM8_AGAIN01 0x009E /* Antenna Gain (in dBm Q5.2) */
#define SSB_SPROM8_AGAIN0 0x00FF /* Antenna 0 */
#define SSB_SPROM8_AGAIN0_SHIFT 0
#define SSB_SPROM8_AGAIN1 0xFF00 /* Antenna 1 */
#define SSB_SPROM8_AGAIN1_SHIFT 8
-#define SSB_SPROM8_AGAIN23 0x10A0
+#define SSB_SPROM8_AGAIN23 0x00A0
#define SSB_SPROM8_AGAIN2 0x00FF /* Antenna 2 */
#define SSB_SPROM8_AGAIN2_SHIFT 0
#define SSB_SPROM8_AGAIN3 0xFF00 /* Antenna 3 */
#define SSB_SPROM8_AGAIN3_SHIFT 8
-#define SSB_SPROM8_GPIOA 0x1096 /*Gen. Purpose IO # 0 and 1 */
-#define SSB_SPROM8_GPIOA_P0 0x00FF /* Pin 0 */
-#define SSB_SPROM8_GPIOA_P1 0xFF00 /* Pin 1 */
-#define SSB_SPROM8_GPIOA_P1_SHIFT 8
-#define SSB_SPROM8_GPIOB 0x1098 /* Gen. Purpose IO # 2 and 3 */
-#define SSB_SPROM8_GPIOB_P2 0x00FF /* Pin 2 */
-#define SSB_SPROM8_GPIOB_P3 0xFF00 /* Pin 3 */
-#define SSB_SPROM8_GPIOB_P3_SHIFT 8
-#define SSB_SPROM8_RSSIPARM2G 0x10A4 /* RSSI params for 2GHz */
+#define SSB_SPROM8_RSSIPARM2G 0x00A4 /* RSSI params for 2GHz */
#define SSB_SPROM8_RSSISMF2G 0x000F
#define SSB_SPROM8_RSSISMC2G 0x00F0
#define SSB_SPROM8_RSSISMC2G_SHIFT 4
@@ -366,7 +366,7 @@
#define SSB_SPROM8_RSSISAV2G_SHIFT 8
#define SSB_SPROM8_BXA2G 0x1800
#define SSB_SPROM8_BXA2G_SHIFT 11
-#define SSB_SPROM8_RSSIPARM5G 0x10A6 /* RSSI params for 5GHz */
+#define SSB_SPROM8_RSSIPARM5G 0x00A6 /* RSSI params for 5GHz */
#define SSB_SPROM8_RSSISMF5G 0x000F
#define SSB_SPROM8_RSSISMC5G 0x00F0
#define SSB_SPROM8_RSSISMC5G_SHIFT 4
@@ -374,47 +374,47 @@
#define SSB_SPROM8_RSSISAV5G_SHIFT 8
#define SSB_SPROM8_BXA5G 0x1800
#define SSB_SPROM8_BXA5G_SHIFT 11
-#define SSB_SPROM8_TRI25G 0x10A8 /* TX isolation 2.4&5.3GHz */
+#define SSB_SPROM8_TRI25G 0x00A8 /* TX isolation 2.4&5.3GHz */
#define SSB_SPROM8_TRI2G 0x00FF /* TX isolation 2.4GHz */
#define SSB_SPROM8_TRI5G 0xFF00 /* TX isolation 5.3GHz */
#define SSB_SPROM8_TRI5G_SHIFT 8
-#define SSB_SPROM8_TRI5GHL 0x10AA /* TX isolation 5.2/5.8GHz */
+#define SSB_SPROM8_TRI5GHL 0x00AA /* TX isolation 5.2/5.8GHz */
#define SSB_SPROM8_TRI5GL 0x00FF /* TX isolation 5.2GHz */
#define SSB_SPROM8_TRI5GH 0xFF00 /* TX isolation 5.8GHz */
#define SSB_SPROM8_TRI5GH_SHIFT 8
-#define SSB_SPROM8_RXPO 0x10AC /* RX power offsets */
+#define SSB_SPROM8_RXPO 0x00AC /* RX power offsets */
#define SSB_SPROM8_RXPO2G 0x00FF /* 2GHz RX power offset */
#define SSB_SPROM8_RXPO5G 0xFF00 /* 5GHz RX power offset */
#define SSB_SPROM8_RXPO5G_SHIFT 8
-#define SSB_SPROM8_MAXP_BG 0x10C0 /* Max Power 2GHz in path 1 */
+#define SSB_SPROM8_MAXP_BG 0x00C0 /* Max Power 2GHz in path 1 */
#define SSB_SPROM8_MAXP_BG_MASK 0x00FF /* Mask for Max Power 2GHz */
#define SSB_SPROM8_ITSSI_BG 0xFF00 /* Mask for path 1 itssi_bg */
#define SSB_SPROM8_ITSSI_BG_SHIFT 8
-#define SSB_SPROM8_PA0B0 0x10C2 /* 2GHz power amp settings */
-#define SSB_SPROM8_PA0B1 0x10C4
-#define SSB_SPROM8_PA0B2 0x10C6
-#define SSB_SPROM8_MAXP_A 0x10C8 /* Max Power 5.3GHz */
+#define SSB_SPROM8_PA0B0 0x00C2 /* 2GHz power amp settings */
+#define SSB_SPROM8_PA0B1 0x00C4
+#define SSB_SPROM8_PA0B2 0x00C6
+#define SSB_SPROM8_MAXP_A 0x00C8 /* Max Power 5.3GHz */
#define SSB_SPROM8_MAXP_A_MASK 0x00FF /* Mask for Max Power 5.3GHz */
#define SSB_SPROM8_ITSSI_A 0xFF00 /* Mask for path 1 itssi_a */
#define SSB_SPROM8_ITSSI_A_SHIFT 8
-#define SSB_SPROM8_MAXP_AHL 0x10CA /* Max Power 5.2/5.8GHz */
+#define SSB_SPROM8_MAXP_AHL 0x00CA /* Max Power 5.2/5.8GHz */
#define SSB_SPROM8_MAXP_AH_MASK 0x00FF /* Mask for Max Power 5.8GHz */
#define SSB_SPROM8_MAXP_AL_MASK 0xFF00 /* Mask for Max Power 5.2GHz */
#define SSB_SPROM8_MAXP_AL_SHIFT 8
-#define SSB_SPROM8_PA1B0 0x10CC /* 5.3GHz power amp settings */
-#define SSB_SPROM8_PA1B1 0x10CE
-#define SSB_SPROM8_PA1B2 0x10D0
-#define SSB_SPROM8_PA1LOB0 0x10D2 /* 5.2GHz power amp settings */
-#define SSB_SPROM8_PA1LOB1 0x10D4
-#define SSB_SPROM8_PA1LOB2 0x10D6
-#define SSB_SPROM8_PA1HIB0 0x10D8 /* 5.8GHz power amp settings */
-#define SSB_SPROM8_PA1HIB1 0x10DA
-#define SSB_SPROM8_PA1HIB2 0x10DC
-#define SSB_SPROM8_CCK2GPO 0x1140 /* CCK power offset */
-#define SSB_SPROM8_OFDM2GPO 0x1142 /* 2.4GHz OFDM power offset */
-#define SSB_SPROM8_OFDM5GPO 0x1146 /* 5.3GHz OFDM power offset */
-#define SSB_SPROM8_OFDM5GLPO 0x114A /* 5.2GHz OFDM power offset */
-#define SSB_SPROM8_OFDM5GHPO 0x114E /* 5.8GHz OFDM power offset */
+#define SSB_SPROM8_PA1B0 0x00CC /* 5.3GHz power amp settings */
+#define SSB_SPROM8_PA1B1 0x00CE
+#define SSB_SPROM8_PA1B2 0x00D0
+#define SSB_SPROM8_PA1LOB0 0x00D2 /* 5.2GHz power amp settings */
+#define SSB_SPROM8_PA1LOB1 0x00D4
+#define SSB_SPROM8_PA1LOB2 0x00D6
+#define SSB_SPROM8_PA1HIB0 0x00D8 /* 5.8GHz power amp settings */
+#define SSB_SPROM8_PA1HIB1 0x00DA
+#define SSB_SPROM8_PA1HIB2 0x00DC
+#define SSB_SPROM8_CCK2GPO 0x0140 /* CCK power offset */
+#define SSB_SPROM8_OFDM2GPO 0x0142 /* 2.4GHz OFDM power offset */
+#define SSB_SPROM8_OFDM5GPO 0x0146 /* 5.3GHz OFDM power offset */
+#define SSB_SPROM8_OFDM5GLPO 0x014A /* 5.2GHz OFDM power offset */
+#define SSB_SPROM8_OFDM5GHPO 0x014E /* 5.8GHz OFDM power offset */
/* Values for SSB_SPROM1_BINF_CCODE */
enum {
View Git Blame Copy Permalink