mirror of
git://projects.qi-hardware.com/openwrt-xburst.git
synced 2024-11-20 04:48:27 +02:00
5fdaea419c
git-svn-id: svn://svn.openwrt.org/openwrt/trunk/openwrt@1548 3c298f89-4303-0410-b956-a3cf2f4a3e73
122 lines
5.3 KiB
Plaintext
122 lines
5.3 KiB
Plaintext
# Kismet drone config file
|
|
|
|
version=2005.04.R1
|
|
|
|
# Name of server (Purely for organiational purposes)
|
|
servername=Kismet
|
|
|
|
# User to setid to (should be your normal user)
|
|
suiduser=nobody
|
|
|
|
# Port to serve packet data... This probably shouldn't be the same as the port
|
|
# you configured kismet_server for, or else you'll have problems running them
|
|
# on the same system.
|
|
tcpport=3501
|
|
# People allowed to connect, comma seperated IP addresses or network/mask
|
|
# blocks. Netmasks can be expressed as dotted quad (/255.255.255.0) or as
|
|
# numbers (/24)
|
|
allowedhosts=127.0.0.1
|
|
# Maximum number of concurrent stream attachments
|
|
maxclients=5
|
|
|
|
# Packet sources:
|
|
# source=capture_cardtype,capture_interface,capture_name
|
|
# Card type - Specifies the type of device. It can be one of:
|
|
# cisco - Cisco card with Linux Kernel drivers
|
|
# cisco_cvs - Cisco card with CVS Linux drivers
|
|
# cisco_bsd - Cisco on *BSD
|
|
# prism2 - Prism2 using wlan-ng drivers with pcap support (all
|
|
# current versions support pcap)
|
|
# prism2_hostap - Prism2 using hostap drivers
|
|
# prism2_legacy - Prism2 using wlan-ng drivers without pcap support (0.1.9)
|
|
# prism2_bsd - Prism2 on *BSD
|
|
# orinoco - Orinoco cards using Snax's patched driers
|
|
# generic - Generic card with no specific support. You will have
|
|
# to put this into monitor mode yourself!
|
|
# wsp100 - WSP100 embedded remote sensor.
|
|
# wtapfile - Saved file of packets readable by libwiretap
|
|
# ar5k - ar5k 802.11a using the vt_ar5k drivers
|
|
# Capture interface - Specifies the network interface Kismet will watch for
|
|
# packets to come in on. Typically "ethX" or "wlanX". For the WSP100 capture
|
|
# engine, the WSP100 device sends packets via a UDP stream, so the capture
|
|
# interface should be in the form of host:port where 'host' is the WSP100 and
|
|
# 'port' is the local UDP port that it will send data to.
|
|
# Capture Name - The name Kismet uses for this capture source. This is the
|
|
# name used to specify what sources to enable.
|
|
#
|
|
# To enable multiple sources, specify a source line for each and then use the
|
|
# enablesources line to enable them. For example:
|
|
# source=prism2,wlan0,prism
|
|
# source=cisco,eth0,cisco
|
|
source=wrt54g,eth1,wireless
|
|
# For v1 hardware uncomment this:
|
|
# source=wrt54g,eth2,wireless
|
|
|
|
# Comma-separated list of sources to enable. This is only needed if you wish
|
|
# to selectively enable multiple sources.
|
|
# enablesources=prism,cisco
|
|
|
|
# Do we channelhop?
|
|
channelhop=true
|
|
|
|
# How many channels per second do we hop? (1-10)
|
|
channelvelocity=5
|
|
|
|
# By setting the dwell time for channel hopping we override the channelvelocity
|
|
# setting above and dwell on each channel for the given number of seconds.
|
|
#channeldwell=10
|
|
|
|
# Do we split channels between cards on the same spectrum? This means if
|
|
# multiple 802.11b capture sources are defined, they will be offset to cover
|
|
# the most possible spectrum at a given time. This also controls splitting
|
|
# fine-tuned sourcechannels lines which cover multiple interfaces (see below)
|
|
splitchannels=true
|
|
|
|
# Basic channel hopping control:
|
|
# These define the channels the cards hop through for various frequency ranges
|
|
# supported by Kismet. More finegrain control is available via the
|
|
# "sourcechannels" configuration option.
|
|
#
|
|
# Don't change the IEEE80211<x> identifiers or channel hopping won't work.
|
|
|
|
# Users outside the US might want to use this list:
|
|
# defaultchannels=IEEE80211b:1,7,13,2,8,3,14,9,4,10,5,11,6,12
|
|
defaultchannels=IEEE80211b:1,6,11,2,7,3,8,4,9,5,10
|
|
|
|
# 802.11g uses the same channels as 802.11b...
|
|
defaultchannels=IEEE80211g:1,6,11,2,7,3,8,4,9,5,10
|
|
|
|
# 802.11a channels are non-overlapping so sequential is fine. You may want to
|
|
# adjust the list depending on the channels your card actually supports.
|
|
# defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64,100,104,108,112,116,120,124,128,132,136,140,149,153,157,161,184,188,192,196,200,204,208,212,216
|
|
defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64
|
|
|
|
# Combo cards like Atheros use both 'a' and 'b/g' channels. Of course, you
|
|
# can also explicitly override a given source. You can use the script
|
|
# extras/listchan.pl to extract all the channels your card supports.
|
|
defaultchannels=IEEE80211ab:1,6,11,2,7,3,8,4,9,5,10,36,40,44,48,52,56,60,64
|
|
|
|
# Fine-tuning channel hopping control:
|
|
# The sourcechannels option can be used to set the channel hopping for
|
|
# specific interfaces, and to control what interfaces share a list of
|
|
# channels for split hopping. This can also be used to easily lock
|
|
# one card on a single channel while hopping with other cards.
|
|
# Any card without a sourcechannel definition will use the standard hopping
|
|
# list.
|
|
# sourcechannels=sourcename[,sourcename]:ch1,ch2,ch3,...chN
|
|
|
|
# ie, for us channels on the source 'prism2source' (same as normal channel
|
|
# hopping behavior):
|
|
# sourcechannels=prism2source:1,6,11,2,7,3,8,4,9,5,10
|
|
|
|
# Given two capture sources, "prism2a" and "prism2b", we want prism2a to stay
|
|
# on channel 6 and prism2b to hop normally. By not setting a sourcechannels
|
|
# line for prism2b, it will use the standard hopping.
|
|
# sourcechannels=prism2a:6
|
|
|
|
# To assign the same custom hop channel to multiple sources, or to split the
|
|
# same custom hop channel over two sources (if splitchannels is true), list
|
|
# them all on the same sourcechannels line:
|
|
# sourcechannels=prism2a,prism2b,prism2c:1,6,11
|
|
|