mirror of
git://projects.qi-hardware.com/openwrt-xburst.git
synced 2024-11-30 14:48:27 +02:00
2cea1e6b9a
openwrt. this gives us the ability to better support different hardware models, without changing any external tar-balls. only et.o and wl.o is missing and is fetched from my webserver. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@379 3c298f89-4303-0410-b956-a3cf2f4a3e73
118 lines
2.8 KiB
C
118 lines
2.8 KiB
C
/*
|
|
* Copyright 2004, Broadcom Corporation
|
|
* All Rights Reserved.
|
|
*
|
|
* THIS SOFTWARE IS OFFERED "AS IS", AND BROADCOM GRANTS NO WARRANTIES OF ANY
|
|
* KIND, EXPRESS OR IMPLIED, BY STATUTE, COMMUNICATION OR OTHERWISE. BROADCOM
|
|
* SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
|
|
* FOR A SPECIFIC PURPOSE OR NONINFRINGEMENT CONCERNING THIS SOFTWARE.
|
|
*
|
|
* $Id$
|
|
*/
|
|
#include <linux/config.h>
|
|
#include <linux/init.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/sched.h>
|
|
#include <linux/serial_reg.h>
|
|
#include <linux/interrupt.h>
|
|
#include <asm/addrspace.h>
|
|
#include <asm/io.h>
|
|
#include <asm/time.h>
|
|
|
|
#include <typedefs.h>
|
|
#include <bcmnvram.h>
|
|
#include <sbconfig.h>
|
|
#include <sbextif.h>
|
|
#include <sbutils.h>
|
|
#include <sbmips.h>
|
|
|
|
/* Global SB handle */
|
|
extern void *bcm947xx_sbh;
|
|
extern spinlock_t bcm947xx_sbh_lock;
|
|
|
|
/* Convenience */
|
|
#define sbh bcm947xx_sbh
|
|
#define sbh_lock bcm947xx_sbh_lock
|
|
|
|
extern int panic_timeout;
|
|
static int watchdog = 0;
|
|
static u8 *mcr = NULL;
|
|
|
|
void __init
|
|
bcm947xx_time_init(void)
|
|
{
|
|
unsigned int hz;
|
|
extifregs_t *eir;
|
|
|
|
/*
|
|
* Use deterministic values for initial counter interrupt
|
|
* so that calibrate delay avoids encountering a counter wrap.
|
|
*/
|
|
write_c0_count(0);
|
|
write_c0_compare(0xffff);
|
|
|
|
if (!(hz = sb_mips_clock(sbh)))
|
|
hz = 100000000;
|
|
|
|
printk("CPU: BCM%04x rev %d at %d MHz\n", sb_chip(sbh), sb_chiprev(sbh),
|
|
(hz + 500000) / 1000000);
|
|
|
|
/* Set MIPS counter frequency for fixed_rate_gettimeoffset() */
|
|
mips_hpt_frequency = hz / 2;
|
|
|
|
/* Set watchdog interval in ms */
|
|
watchdog = simple_strtoul(nvram_safe_get("watchdog"), NULL, 0);
|
|
|
|
/* Please set the watchdog to 3 sec if it is less than 3 but not equal to 0 */
|
|
if (watchdog > 0) {
|
|
if (watchdog < 3000)
|
|
watchdog = 3000;
|
|
}
|
|
|
|
|
|
/* Set panic timeout in seconds */
|
|
panic_timeout = watchdog / 1000;
|
|
|
|
/* Setup blink */
|
|
if ((eir = sb_setcore(sbh, SB_EXTIF, 0))) {
|
|
sbconfig_t *sb = (sbconfig_t *)((unsigned int) eir + SBCONFIGOFF);
|
|
unsigned long base = EXTIF_CFGIF_BASE(sb_base(readl(&sb->sbadmatch1)));
|
|
mcr = (u8 *) ioremap_nocache(base + UART_MCR, 1);
|
|
}
|
|
}
|
|
|
|
static void
|
|
bcm947xx_timer_interrupt(int irq, void *dev_id, struct pt_regs *regs)
|
|
{
|
|
/* Generic MIPS timer code */
|
|
timer_interrupt(irq, dev_id, regs);
|
|
|
|
/* Set the watchdog timer to reset after the specified number of ms */
|
|
if (watchdog > 0)
|
|
sb_watchdog(sbh, WATCHDOG_CLOCK / 1000 * watchdog);
|
|
|
|
#ifdef CONFIG_HWSIM
|
|
(*((int *)0xa0000f1c))++;
|
|
#else
|
|
/* Blink one of the LEDs in the external UART */
|
|
if (mcr && !(jiffies % (HZ/2)))
|
|
writeb(readb(mcr) ^ UART_MCR_OUT2, mcr);
|
|
#endif
|
|
}
|
|
|
|
static struct irqaction bcm947xx_timer_irqaction = {
|
|
bcm947xx_timer_interrupt,
|
|
SA_INTERRUPT,
|
|
0,
|
|
"timer",
|
|
NULL,
|
|
NULL
|
|
};
|
|
|
|
void __init
|
|
bcm947xx_timer_setup(struct irqaction *irq)
|
|
{
|
|
/* Enable the timer interrupt */
|
|
setup_irq(7, &bcm947xx_timer_irqaction);
|
|
}
|