mirror of
git://projects.qi-hardware.com/openwrt-xburst.git
synced 2025-02-12 20:31:55 +02:00
c1cb37da16
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@13670 3c298f89-4303-0410-b956-a3cf2f4a3e73
156 lines
8.9 KiB
C
156 lines
8.9 KiB
C
#ifndef __DANUBE_GPTU_DEV_H__2005_07_26__10_19__
|
|
#define __DANUBE_GPTU_DEV_H__2005_07_26__10_19__
|
|
|
|
|
|
/******************************************************************************
|
|
Copyright (c) 2002, Infineon Technologies. All rights reserved.
|
|
|
|
No Warranty
|
|
Because the program is licensed free of charge, there is no warranty for
|
|
the program, to the extent permitted by applicable law. Except when
|
|
otherwise stated in writing the copyright holders and/or other parties
|
|
provide the program "as is" without warranty of any kind, either
|
|
expressed or implied, including, but not limited to, the implied
|
|
warranties of merchantability and fitness for a particular purpose. The
|
|
entire risk as to the quality and performance of the program is with
|
|
you. should the program prove defective, you assume the cost of all
|
|
necessary servicing, repair or correction.
|
|
|
|
In no event unless required by applicable law or agreed to in writing
|
|
will any copyright holder, or any other party who may modify and/or
|
|
redistribute the program as permitted above, be liable to you for
|
|
damages, including any general, special, incidental or consequential
|
|
damages arising out of the use or inability to use the program
|
|
(including but not limited to loss of data or data being rendered
|
|
inaccurate or losses sustained by you or third parties or a failure of
|
|
the program to operate with any other programs), even if such holder or
|
|
other party has been advised of the possibility of such damages.
|
|
******************************************************************************/
|
|
|
|
|
|
/*
|
|
* ####################################
|
|
* Definition
|
|
* ####################################
|
|
*/
|
|
|
|
/*
|
|
* Available Timer/Counter Index
|
|
*/
|
|
#define TIMER(n, X) (n * 2 + (X ? 1 : 0))
|
|
#define TIMER_ANY 0x00
|
|
#define TIMER1A TIMER(1, 0)
|
|
#define TIMER1B TIMER(1, 1)
|
|
#define TIMER2A TIMER(2, 0)
|
|
#define TIMER2B TIMER(2, 1)
|
|
#define TIMER3A TIMER(3, 0)
|
|
#define TIMER3B TIMER(3, 1)
|
|
|
|
/*
|
|
* Flag of Timer/Counter
|
|
* These flags specify the way in which timer is configured.
|
|
*/
|
|
/* Bit size of timer/counter. */
|
|
#define TIMER_FLAG_16BIT 0x0000
|
|
#define TIMER_FLAG_32BIT 0x0001
|
|
/* Switch between timer and counter. */
|
|
#define TIMER_FLAG_TIMER 0x0000
|
|
#define TIMER_FLAG_COUNTER 0x0002
|
|
/* Stop or continue when overflowing/underflowing. */
|
|
#define TIMER_FLAG_ONCE 0x0000
|
|
#define TIMER_FLAG_CYCLIC 0x0004
|
|
/* Count up or counter down. */
|
|
#define TIMER_FLAG_UP 0x0000
|
|
#define TIMER_FLAG_DOWN 0x0008
|
|
/* Count on specific level or edge. */
|
|
#define TIMER_FLAG_HIGH_LEVEL_SENSITIVE 0x0000
|
|
#define TIMER_FLAG_LOW_LEVEL_SENSITIVE 0x0040
|
|
#define TIMER_FLAG_RISE_EDGE 0x0010
|
|
#define TIMER_FLAG_FALL_EDGE 0x0020
|
|
#define TIMER_FLAG_ANY_EDGE 0x0030
|
|
/* Signal is syncronous to module clock or not. */
|
|
#define TIMER_FLAG_UNSYNC 0x0000
|
|
#define TIMER_FLAG_SYNC 0x0080
|
|
/* Different interrupt handle type. */
|
|
#define TIMER_FLAG_NO_HANDLE 0x0000
|
|
#if defined(__KERNEL__)
|
|
#define TIMER_FLAG_CALLBACK_IN_IRQ 0x0100
|
|
#endif // defined(__KERNEL__)
|
|
#define TIMER_FLAG_SIGNAL 0x0300
|
|
/* Internal clock source or external clock source */
|
|
#define TIMER_FLAG_INT_SRC 0x0000
|
|
#define TIMER_FLAG_EXT_SRC 0x1000
|
|
|
|
|
|
/*
|
|
* ioctl Command
|
|
*/
|
|
#define GPTU_REQUEST_TIMER 0x01 /* General method to setup timer/counter. */
|
|
#define GPTU_FREE_TIMER 0x02 /* Free timer/counter. */
|
|
#define GPTU_START_TIMER 0x03 /* Start or resume timer/counter. */
|
|
#define GPTU_STOP_TIMER 0x04 /* Suspend timer/counter. */
|
|
#define GPTU_GET_COUNT_VALUE 0x05 /* Get current count value. */
|
|
#define GPTU_CALCULATE_DIVIDER 0x06 /* Calculate timer divider from given freq.*/
|
|
#define GPTU_SET_TIMER 0x07 /* Simplified method to setup timer. */
|
|
#define GPTU_SET_COUNTER 0x08 /* Simplified method to setup counter. */
|
|
|
|
/*
|
|
* Data Type Used to Call ioctl
|
|
*/
|
|
struct gptu_ioctl_param {
|
|
unsigned int timer; /* In command GPTU_REQUEST_TIMER, GPTU_SET_TIMER, and *
|
|
* GPTU_SET_COUNTER, this field is ID of expected *
|
|
* timer/counter. If it's zero, a timer/counter would *
|
|
* be dynamically allocated and ID would be stored in *
|
|
* this field. *
|
|
* In command GPTU_GET_COUNT_VALUE, this field is *
|
|
* ignored. *
|
|
* In other command, this field is ID of timer/counter *
|
|
* allocated. */
|
|
unsigned int flag; /* In command GPTU_REQUEST_TIMER, GPTU_SET_TIMER, and *
|
|
* GPTU_SET_COUNTER, this field contains flags to *
|
|
* specify how to configure timer/counter. *
|
|
* In command GPTU_START_TIMER, zero indicate start *
|
|
* and non-zero indicate resume timer/counter. *
|
|
* In other command, this field is ignored. */
|
|
unsigned long value; /* In command GPTU_REQUEST_TIMER, this field contains *
|
|
* init/reload value. *
|
|
* In command GPTU_SET_TIMER, this field contains *
|
|
* frequency (0.001Hz) of timer. *
|
|
* In command GPTU_GET_COUNT_VALUE, current count *
|
|
* value would be stored in this field. *
|
|
* In command GPTU_CALCULATE_DIVIDER, this field *
|
|
* contains frequency wanted, and after calculation, *
|
|
* divider would be stored in this field to overwrite *
|
|
* the frequency. *
|
|
* In other command, this field is ignored. */
|
|
int pid; /* In command GPTU_REQUEST_TIMER and GPTU_SET_TIMER, *
|
|
* if signal is required, this field contains process *
|
|
* ID to which signal would be sent. *
|
|
* In other command, this field is ignored. */
|
|
int sig; /* In command GPTU_REQUEST_TIMER and GPTU_SET_TIMER, *
|
|
* if signal is required, this field contains signal *
|
|
* number which would be sent. *
|
|
* In other command, this field is ignored. */
|
|
};
|
|
|
|
/*
|
|
* ####################################
|
|
* Data Type
|
|
* ####################################
|
|
*/
|
|
typedef void (*timer_callback)(unsigned long arg);
|
|
|
|
extern int ifxmips_request_timer(unsigned int, unsigned int, unsigned long, unsigned long, unsigned long);
|
|
extern int ifxmips_free_timer(unsigned int);
|
|
extern int ifxmips_start_timer(unsigned int, int);
|
|
extern int ifxmips_stop_timer(unsigned int);
|
|
extern int ifxmips_reset_counter_flags(u32 timer, u32 flags);
|
|
extern int ifxmips_get_count_value(unsigned int, unsigned long *);
|
|
extern u32 ifxmips_cal_divider(unsigned long);
|
|
extern int ifxmips_set_timer(unsigned int, unsigned int, int, int, unsigned int, unsigned long, unsigned long);
|
|
extern int ifxmips_set_counter(unsigned int timer, unsigned int flag,
|
|
u32 reload, unsigned long arg1, unsigned long arg2);
|
|
|
|
#endif /* __DANUBE_GPTU_DEV_H__2005_07_26__10_19__ */
|