Remove loglevel from default kernel boot arguments to
let kernel use its default configuration.
Signed-off-by: Sebastian Krzyszkowiak <seba.dos1@gmail.com>
In most conditions the charger is unable to detect battery full status
because gsm modem continiously draws current directly from the battery.
This makes it less sensitive and therefore will cutoff charging properly.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
This makes Qi consistent with current SHR boot script. It assigns
the MAC specified on the identity partition to the device and the
next address to the host, ie: from "g_ether.dev_addr=00:1F:11:01:58:67"
generate "g_ether.host_addr=00:1F:11:01:58:68".
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Qi fails to boot from NAND. Qi booting from SD goes fine. Booting NAND
from NOR works as well.
I have found the problem. The error was because we check if the
current block is bad or the next one is bad. And skip the current
block even if only the next one is bad. This way we skip good block
before a bad one.
This patch fixes the bug.
Signed-off-by: Dmitry Kurochkin <dmitry.kurochkin@gmail.com>
The fdisk and mkfs was factored out into a shell function
so that it is easier to create dirfferent partition layouts.
The default case was left the same as the original script
The partitions can be specified as percentages of the
available space (after Qi reserved space has been taken out)
by providing a comma separated list of values:
e.g. 25,0,50
Which would create partitions 1 and 3 with 25% and 50%
of the usable capacity. Partitions 2 and 4 would not be
assigned.
Signed-off-by: Christopher Hall <hsw@openmoko.com>
s3c6410 defaults to all clocks up, this leads to 120mA idle current at 5V.
Gating all the unused clocks off gets us down to 76mA idle current at 533Mhz
CPU clock down to 133MHz only helps by a further ~1.5mA.
During these tests camera unit was active with no camera attached, no EDGE.
Signed-off-by: Andy Green <andy@openmoko.com>
Hello Andy,
I am in the process of making a modified 6410-partition.sh
and I wonder if there is a mistake in the VFAT partition size:
Shouldn't the "+ $REARSECTORS" in the FATSECTORS calculation
be a subtraction, otherwise the backupfs will overlap the
space reserved for Qi at the end of the SD Card.
Please look at this dif to see what I mean:
Hi Andy,
Sorry, previous patch to enable reset function of LCM is not working
stably somehow. :(
Since it's pin configuration is input. Attached patch is to set LCM
reset pin as output.
Cheers,
Matt
We can get rid of quite a few backslashes since in modern C,
consecutive strings are concatenated at compile time.
Signed-off-by: Werner Almesberger <werner@openmoko.org>
Received: from mail.openmoko.org ([unix socket])
by mail.openmoko.org (Cyrus v2.1.18-IPv6-Debian-2.1.18-5.1) with LMTP; Sat, 07 Mar 2009 06:46:20 +0000
X-Sieve: CMU Sieve 2.2
Return-path: <openmoko-kernel-bounces@lists.openmoko.org>
Received: from sita.openmoko.org ([88.198.124.203])
by mail.openmoko.org with esmtps (TLS-1.0:RSA_AES_256_CBC_SHA1:32)
(Exim 4.63)
(envelope-from <openmoko-kernel-bounces@lists.openmoko.org>)
id 1LfqIe-000690-LR
for andy@imap.openmoko.org; Sat, 07 Mar 2009 06:46:20 +0000
Received: from localhost ([127.0.0.1] helo=sita.openmoko.org)
by sita.openmoko.org with esmtp (Exim 4.63)
(envelope-from <openmoko-kernel-bounces@lists.openmoko.org>)
id 1LfqIA-0005iO-2x; Sat, 07 Mar 2009 07:45:50 +0100
Received: from imap.tw.openmoko.org ([59.124.115.149] helo=aakash.openmoko.org)
by sita.openmoko.org with esmtp (Exim 4.63)
(envelope-from <matt_hsu@openmoko.org>) id 1LfqI0-0005cg-Rz
for openmoko-kernel@lists.openmoko.org; Sat, 07 Mar 2009 07:45:44 +0100
Received: from [172.16.22.173] (helo=abacus-om.tw.openmoko.com
ident=Debian-exim)
by aakash.openmoko.org with esmtps (TLS-1.0:RSA_AES_256_CBC_SHA1:32)
(Exim 4.63) (envelope-from <matt_hsu@openmoko.org>)
id 1LfqHA-0007Xa-Eu
for openmoko-kernel@lists.openmoko.org; Sat, 07 Mar 2009 14:45:09 +0800
Received: from matt by abacus-om.tw.openmoko.com with local (Exim 4.69)
(envelope-from <matt_hsu@openmoko.org>) id 1Lfqto-0006XS-9X
for openmoko-kernel@lists.openmoko.org; Sat, 07 Mar 2009 15:24:44 +0800
From: Matt Hsu <matt_hsu@openmoko.org>
To: openmoko-kernel@lists.openmoko.org
Date: Sat, 7 Mar 2009 15:24:42 +0800
Message-Id: <1236410684-20364-2-git-send-email-matt_hsu@openmoko.org>
X-Mailer: git-send-email 1.5.6.5
In-Reply-To: <1236410684-20364-1-git-send-email-matt_hsu@openmoko.org>
References: <1236410684-20364-1-git-send-email-matt_hsu@openmoko.org>
X-Spam-Checker-Version: SpamAssassin 3.2.3 (2007-08-08) on sita.openmoko.org
X-Spam-Level:
X-Spam-Status: No, score=-2.6 required=5.0 tests=AWL,BAYES_00 autolearn=ham
version=3.2.3
Subject: [PATCH 1/3] qi/om_3d7k: deassert LCM_RESET pin before getting kernel.
X-BeenThere: openmoko-kernel@lists.openmoko.org
X-Mailman-Version: 2.1.9
Precedence: list
List-Id: Discussion regarding the OpenMoko Linux Kernel and boot loader
<openmoko-kernel.lists.openmoko.org>
List-Unsubscribe: <http://lists.openmoko.org/mailman/listinfo/openmoko-kernel>,
<mailto:openmoko-kernel-request@lists.openmoko.org?subject=unsubscribe>
List-Archive: <http://lists.openmoko.org/pipermail/openmoko-kernel>
List-Post: <mailto:openmoko-kernel@lists.openmoko.org>
List-Help: <mailto:openmoko-kernel-request@lists.openmoko.org?subject=help>
List-Subscribe: <http://lists.openmoko.org/mailman/listinfo/openmoko-kernel>,
<mailto:openmoko-kernel-request@lists.openmoko.org?subject=subscribe>
Sender: openmoko-kernel-bounces@lists.openmoko.org
Errors-To: openmoko-kernel-bounces@lists.openmoko.org
Since the reset callback function of probing jbt6k74 is
eliminated for some reasons in kernel. In order to support
both of LCM driver device, l1k002 and jbt6k74, just issue this reset in qi stage.
Signed-off-by: Matt Hsu <matt_hsu@openmoko.org>
This patch uses fdisk instead of dmesg to determine the size of
the uSD card. This should be less fragile and is much simpler
than the previous solution.
Signed-off-by: Werner Almesberger <werner@openmoko.org>
6410-partition-sd.sh didn't handle Debian, which is just like Ubuntu 7.
(Tested on "lenny". YMMV.)
Signed-off-by: Werner Almesberger <werner@openmoko.org>
There's no trailing space after the last mac address addition, it
was broken before the recent patch adding the second mac address.
Also, we don't need to add the first space by hand if it's unconditionally
added in the string afterwards.
Reported-by: Werner Almesberger <werner@openmoko.org>
Signed-off-by: Andy Green <andy@openmoko.com>
Andy,
On Tuesday 03 February 2009 18:12:50 Andy Green wrote:
> Now everything else is in place, we are able to mount
> the GTA02 "identity" partition and extract the USB Ethernet
> MAC Address from it, and add it to the kernel commandline.
>
> This causes the Ethernet gadget to use the same MAC address
> each boot, simplifying DHCP server situation. The MAC
> address in the identity partition is globally unique from
> the factory.
Because of this patch I can no longer load g_ether module with host_addr= and
dev_addr= parameters.
The module is always loaded using factory mac for HOST and random mac for DEV.
That messes up my setup a bit, as I use NetworkManager 0.7 on FreeRunner
itself (and it expects DEV mac to be the same each time).
Would it be a problem to also include g_ether.dev_addr?
Attached patch solves my problem.
Rob
There's one more thing that wants dynpart computed block offset -
the kernel offset used for NAND boot.
This patch moves the business end of the dynparts computation into
the port_init_gta02() so it's done earlier, and writes the block
index into the board_api struct NAND option's partition block start
field.
It also adds a field to the nand_dynparts struct so we can hold both
the true length and true block offset for each partition for later
use by the original code in append_device_specific_cmdline_gta02.
Signed-off-by: Andy Green <andy@openmoko.com>
Now everything else is in place, we are able to mount
the GTA02 "identity" partition and extract the USB Ethernet
MAC Address from it, and add it to the kernel commandline.
This causes the Ethernet gadget to use the same MAC address
each boot, simplifying DHCP server situation. The MAC
address in the identity partition is globally unique from
the factory.
Signed-off-by: Andy Green <andy@openmoko.com>
Previously we insisted on NAND block granularity read addressing
and buffer length, even though we normalized the block indexing to
512 bytes to be compatible with ext2 and SD.
This patch improves the read functions so they are completely 512-
block friendly, any number of 512 byte blocks can be fetched from
any 512 byte boundary now.
Signed-off-by: Andy Green <andy@openmoko.com>
This adds dynamic partition computation support for Qi on GTA02.
It's for compatability with existing GTA02 using U-Boot partition
scheme where a bad block in the previous partition moves on the
start of the next partition by one block.
It's important that Qi has no private state, so we need to compute
the NAND arrangement each boot. It turns out this is extremely fast
using Qi's bad block code originally from Xinagfu.
Signed-off-by: Andy Green <andy@openmoko.com>
Add a board API callback that allows a device-specific
commandline area to be created at the time the kernel
commandline is being composed.
Signed-off-by: Andy Green <andy@openmoko.com>
Changes in the last couple of weeks aimed at cleaning this
code broke the block device init cache logic. This patch
restores the logic and reduces the card init failures when
there is no SD Card present to 1 regardless of the number
of partitions probed on the card.
Together with the reduction in Glamo card wait on init this
reduces the delay before trying NAND to 1/9th of before the
patches.
Signed-off-by: Andy Green <andy@openmoko.com>
3000 retries is a very long time for an SD card to wake up,
far longer than should be necessary. This patch reduces it
to 1000.
Signed-off-by: Andy Green <andy@openmoko.com>
On ext2 the symlink can be stored in inode itself if it's not larger than
60 bytes. If the symlink path is exactly 60 bytes, then one more byte is
needed to store terminating NULL, therefore the path is placed in a
separate block.
The PMU initializes all GPIOs to inputs in NoPower, including GPIO2,
which drives GSM_ON and has an external pull-up. Furthermore, we may
have entered PMU.Standby with the modem up.
Unlike u-boot, qi didn't initialize the GPIOs. With this patch is
does.
Reported-by: Paul Ferster <fercerpav@gmail.com>
Signed-off-by: Werner Almesberger <werner@openmoko.org>
On the devices where we have only 2 physical buttons, one of those buttons
(i.e. POWER) is connected directly to PMU. The other button (AUX) is
connected directly to S3C pin and we can get its state immediately, it is
currently used to skip a boot possibility. To allow user to debug boot
problems we can use the POWER button, but we cannot poll for it too many
times as it slows down the boot considerably, therefore a dedicated
function is needed.
Finally all the restructuring pays off: we can cleanly separate the
uImage loader from all the rest, which will make it easy to add
loaders for other kernel image formats.
Signed-off-by: Werner Almesberger <werner@openmoko.org>
This makes things a little easier to read, particularly when we return
this pointer from a function, which we'll do in the next patch.
Signed-off-by: Werner Almesberger <werner@openmoko.org>
