#include #include #include #include #include #include #define GTA03_DEBUG_UART 2 #define PCF50633_I2C_ADS 0x73 static const struct board_variant board_variants[] = { [0] = { .name = "EVB PCB", .machine_revision = 0x010, }, }; void port_init_gta03(void) { unsigned int * MPLLCON = (unsigned int *)0x4c000004; unsigned int * UPLLCON = (unsigned int *)0x4c000008; unsigned int * CLKDIVN = (unsigned int *)0x4c000014; //CAUTION:Follow the configuration order for setting the ports. // 1) setting value(GPnDAT) // 2) setting control register (GPnCON) // 3) configure pull-up resistor(GPnUP) /* 32bit data bus configuration */ /* * === PORT A GROUP * Ports : GPA22 GPA21 GPA20 GPA19 GPA18 GPA17 GPA16 GPA15 GPA14 GPA13 GPA12 * Signal : nFCE nRSTOUT nFRE nFWE ALE CLE nGCS5 nGCS4 nGCS3 nGCS2 nGCS1 * Binary : 1 1 1 , 1 1 1 1 , 1 1 1 1 * Ports : GPA11 GPA10 GPA9 GPA8 GPA7 GPA6 GPA5 GPA4 GPA3 GPA2 GPA1 GPA0 * Signal : ADDR26 ADDR25 ADDR24 ADDR23 ADDR22 ADDR21 ADDR20 ADDR19 ADDR18 ADDR17 ADDR16 ADDR0 * Binary : 1 1 1 1 , 1 1 1 1 , 1 1 1 1 */ rGPACON = 0x007F8FFF; /* * ===* PORT B GROUP * Ports : GPB10 GPB9 GPB8 GPB7 GPB6 GPB5 GPB4 GPB3 GPB2 GPB1 GPB0 * Signal : nXDREQ0 nXDACK0 nXDREQ1 nXDACK1 nSS_KBD nDIS_OFF L3CLOCK L3DATA L3MODE nIrDATXDEN Keyboard * Setting: INPUT OUTPUT INPUT OUTPUT INPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT * Binary : 00 , 01 00 , 01 00 , 01 01 , 01 01 , 01 01 */ rGPBCON = 0x00145554; rGPBDAT |= (1 <<9 ); /* USB_PULLUP */ rGPBUP = 0x000007FF; /* * === PORT C GROUP * Ports : GPC15 GPC14 GPC13 GPC12 GPC11 GPC10 GPC9 GPC8 GPC7 GPC6 GPC5 GPC4 GPC3 GPC2 GPC1 GPC0 * Signal : VD7 VD6 VD5 VD4 VD3 VD2 VD1 VD0 LCDVF2 LCDVF1 LCDVF0 VM VFRAME VLINE VCLK LEND * Binary : 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 */ rGPCCON = 0xAAA776E9; rGPCUP = 0x0000FFFF; rGPCDAT |= (1 << 9); /* WLAN_nRESET pull high */ /* * === PORT D GROUP * Ports : GPD15 GPD14 GPD13 GPD12 GPD11 GPD10 GPD9 GPD8 GPD7 GPD6 GPD5 GPD4 GPD3 GPD2 GPD1 GPD0 * Signal : VD23 VD22 VD21 VD20 VD19 VD18 VD17 VD16 VD15 VD14 VD13 VD12 VD11 VD10 VD9 VD8 * Binary : 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 ,10 10 */ rGPDCON = 0xAAA0AAA5; rGPDUP = 0x0000FFFF; /* * === PORT E GROUP * Ports : GPE15 GPE14 GPE13 GPE12 GPE11 GPE10 GPE9 GPE8 GPE7 GPE6 GPE5 GPE4 * Signal : IICSDA IICSCL SPICLK SPIMOSI SPIMISO SDDATA3 SDDATA2 SDDATA1 SDDATA0 SDCMD SDCLK I2SSDO * Binary : 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , 10 10 , * ------------------------------------------------------------------------------------------------------- * Ports : GPE3 GPE2 GPE1 GPE0 * Signal : I2SSDI CDCLK I2SSCLK I2SLRCK * Binary : 10 10 , 10 10 */ rGPECON = 0xAAAAAAAA; rGPEUP = 0x0000FFFF; /* * === PORT F GROUP * Ports : GPF7 GPF6 GPF5 GPF4 GPF3 GPF2 GPF1 GPF0 * Signal : nLED_8 nLED_4 nLED_2 nLED_1 nIRQ_PCMCIA EINT2 KBDINT EINT0 * Setting: Output Output Output Output EINT3 EINT2 EINT1 EINT0 * Binary : 01 01 , 01 01 , 10 10 , 10 10 */ rGPFCON = 0x0000AAAA; rGPFUP = 0x000000FF; /* * === PORT G GROUP * Ports : GPG15 GPG14 GPG13 GPG12 GPG11 GPG10 GPG9 GPG8 GPG7 GPG6 * Signal : nYPON YMON nXPON XMON EINT19 DMAMODE1 DMAMODE0 DMASTART KBDSPICLK KBDSPIMOSI * Setting: nYPON YMON nXPON XMON EINT19 Output Output Output SPICLK1 SPIMOSI1 * Binary : 11 11 , 11 11 , 10 01 , 01 01 , 11 11 * ----------------------------------------------------------------------------------------- * Ports : GPG5 GPG4 GPG3 GPG2 GPG1 GPG0 * Signal : KBDSPIMISO LCD_PWREN EINT11 nSS_SPI IRQ_LAN IRQ_PCMCIA * Setting: SPIMISO1 LCD_PWRDN EINT11 nSS0 EINT9 EINT8 * Binary : 11 11 , 10 11 , 10 10 */ rGPGCON = 0x02A9FE5A; rGPGUP = 0x0000FFFF; /* * === PORT H GROUP * Ports : GPH10 GPH9 GPH8 GPH7 GPH6 GPH5 GPH4 GPH3 GPH2 GPH1 GPH0 * Signal : CLKOUT1 CLKOUT0 UCLK RXD2 TXD2 RXD1 TXD1 RXD0 TXD0 nRTS0 nCTS0 * Binary : 10 , 10 10 , 11 11 , 10 10 , 10 10 , 10 10 */ /* pulldown on GPH08: UEXTCLK, just floats! * pulldown GPH0 -- nCTS0 / RTS_MODEM -- floats when GSM off * pulldown GPH3 -- RXD[0] / TX_MODEM -- floats when GSM off */ rGPHCON = 0x0019A0AA; rGPHUP = 0x000007FF; /* pulldown on GPJ00: input, just floats! */ /* pulldown on GPJ07: WLAN module WLAN_GPIO0, no ext pull */ rGPJCON = 0x02AAAAAA; rGPJUP = 0x1FFFF; /* * We have to talk to the PMU a little bit */ /* We need SD Card rail (HCLDO) at 3.0V */ i2c_write_sync(&bb_s3c24xx, PCF50633_I2C_ADS, PCF50633_REG_HCLDOOUT, 21); /* switch HCLDO on */ i2c_write_sync(&bb_s3c24xx, PCF50633_I2C_ADS, PCF50633_REG_HCLDOENA, 1); /* push DOWN1 (CPU Core rail) to 1.7V, allowing 533MHz */ i2c_write_sync(&bb_s3c24xx, PCF50633_I2C_ADS, PCF50633_REG_DOWN1OUT, 0x2b); /* change CPU clocking to 533MHz 1:4:8 */ /* clock divide 1:4:8 - do it first */ *CLKDIVN = 5; /* configure UPLL */ *UPLLCON = ((88 << 12) + (4 << 4) + 2); /* Magic delay: Page 7-19, seven nops between UPLL and MPLL */ asm __volatile__ ( "nop\n"\ "nop\n"\ "nop\n"\ "nop\n"\ "nop\n"\ "nop\n"\ "nop\n"\ ); /* configure MPLL */ *MPLLCON = ((169 << 12) + (2 << 4) + 1); serial_init_115200_s3c24xx(GTA03_DEBUG_UART, 50 /*MHz PCLK */); } /** * returns PCB revision information in b0, d8, d9 * GTA03 EVB returns 0x000 * GTA03 returns 0x001 */ int gta03_get_pcb_revision(void) { int n; u32 u; /* make B0 inputs */ rGPBCON &= ~0x00000003; /* D8 and D9 inputs */ rGPDCON &= ~0x000f0000; /* delay after changing pulldowns */ u = rGPBDAT; u = rGPDDAT; /* read the version info */ u = rGPBDAT; n = (u >> (0 - 0))& 0x001; u = rGPDDAT; n |= (u >> (8 -1)) & 0x002; n |= (u >> (9 - 2)) & 0x004; /* * when not being interrogated, all of the revision GPIO * are set to output */ /* make B0 high ouput */ rGPBCON |= 0x00000001; /* D8 and D9 high ouputs */ rGPDCON |= 0x00050000; return n; } const struct board_variant const * get_board_variant_gta03(void) { return &board_variants[gta03_get_pcb_revision()]; } int is_this_board_gta03(void) { /* FIXME: find something gta03 specific */ return 1; } static void putc_gta03(char c) { serial_putc_s3c24xx(GTA03_DEBUG_UART, c); } /* * our API for bootloader on this machine */ const struct board_api board_api_gta03 = { .name = "GTA03", .linux_machine_id = 1808, .linux_mem_start = 0x30000000, .linux_mem_size = (128 * 1024 * 1024), .linux_tag_placement = 0x30000000 + 0x100, .get_board_variant = get_board_variant_gta03, .is_this_board = is_this_board_gta03, .port_init = port_init_gta03, .putc = putc_gta03, /* these are the ways we could boot GTA03 in order to try */ .kernel_source = { [0] = { .name = "NAND Kernel", .block_read = nand_read_ll, .offset_blocks512_if_no_partition = 0x80000 / 512, .filesystem = FS_RAW, .commandline = "neo1973-nand:" \ "0x00040000(qi)," \ "0x00040000(cmdline)," \ "0x00800000(backupkernel)," \ "0x000a0000(extra)," \ "0x00040000(identity)," \ "0x0f6a0000(backuprootfs) " \ "rootfstype=jffs2 " \ "root=/dev/mtdblock6 " \ "console=ttySAC2,115200 " \ "loglevel=4 " \ "init=/sbin/init "\ "ro" }, }, };