mirror of
git://projects.qi-hardware.com/xue.git
synced 2024-11-08 21:09:43 +02:00
135 lines
9.7 KiB
Systemverilog
135 lines
9.7 KiB
Systemverilog
/****************************************************************************************
|
|
*
|
|
* Disclaimer This software code and all associated documentation, comments or other
|
|
* of Warranty: information (collectively "Software") is provided "AS IS" without
|
|
* warranty of any kind. MICRON TECHNOLOGY, INC. ("MTI") EXPRESSLY
|
|
* DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
|
|
* TO, NONINFRINGEMENT OF THIRD PARTY RIGHTS, AND ANY IMPLIED WARRANTIES
|
|
* OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. MTI DOES NOT
|
|
* WARRANT THAT THE SOFTWARE WILL MEET YOUR REQUIREMENTS, OR THAT THE
|
|
* OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE.
|
|
* FURTHERMORE, MTI DOES NOT MAKE ANY REPRESENTATIONS REGARDING THE USE OR
|
|
* THE RESULTS OF THE USE OF THE SOFTWARE IN TERMS OF ITS CORRECTNESS,
|
|
* ACCURACY, RELIABILITY, OR OTHERWISE. THE ENTIRE RISK ARISING OUT OF USE
|
|
* OR PERFORMANCE OF THE SOFTWARE REMAINS WITH YOU. IN NO EVENT SHALL MTI,
|
|
* ITS AFFILIATED COMPANIES OR THEIR SUPPLIERS BE LIABLE FOR ANY DIRECT,
|
|
* INDIRECT, CONSEQUENTIAL, INCIDENTAL, OR SPECIAL DAMAGES (INCLUDING,
|
|
* WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION,
|
|
* OR LOSS OF INFORMATION) ARISING OUT OF YOUR USE OF OR INABILITY TO USE
|
|
* THE SOFTWARE, EVEN IF MTI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
|
|
* DAMAGES. Because some jurisdictions prohibit the exclusion or
|
|
* limitation of liability for consequential or incidental damages, the
|
|
* above limitation may not apply to you.
|
|
*
|
|
* Copyright 2005 Micron Technology, Inc. All rights reserved.
|
|
*
|
|
*
|
|
* Revisions: baaab - 06/20/06 - tMRD was set to 2.0 ns but should be 2 * tCK. Fixed.
|
|
* Added ROW_BITS & BA_BITS for compatibility w/our system.
|
|
* Also changed x16 Col bits from 8 to 9 per spec.
|
|
* Removed part size parameter.
|
|
*
|
|
****************************************************************************************/
|
|
|
|
// Parameters current with 256Mb datasheet rev E (05/07)
|
|
// 04.17.08 - Parameters current with 256Mb Data sheet rev H (03/08)
|
|
|
|
// Timing parameters based on Speed Grade
|
|
|
|
// SYMBOL UNITS DESCRIPTION
|
|
// ------ ----- -----------
|
|
`ifdef sg6 // Timing Parameters for -6 (CL = 3)
|
|
parameter tAC3_max = 5.0; // tAC ns Access window of DQ from CK/CK#
|
|
parameter tAC2_max = 6.5; // tAC ns Access window of DQ from CK/CK#
|
|
parameter tCK = 6.0; // tCK ns Nominal Clock Cycle Time
|
|
parameter tCK3_min = 6.0; // tCK ns Nominal Clock Cycle Time
|
|
parameter tCK2_min = 12.0; // tCK ns Nominal Clock Cycle Time
|
|
parameter tDQSQ = 0.50; // tDQSQ ns DQS-DQ skew, DQS to last DQ valid, per group, per access
|
|
parameter tHZ3_max = 5.0; // tHZ ns Data-out high Z window from CK/CK#
|
|
parameter tHZ2_max = 6.5; // tHZ ns Data-out high Z window from CK/CK#
|
|
parameter tRAS = 42.0; // tRAS ns Active to Precharge command time
|
|
parameter tRC = 60.0; // tRC ns Active to Active/Auto Refresh command time
|
|
parameter tRCD = 18.0; // tRCD ns Active to Read/Write command time
|
|
parameter tRP = 18.0; // tRP ns Precharge command period
|
|
parameter tRRD = 12.0; // tRRD ns Active bank a to Active bank b command time
|
|
parameter tWR = 12.0; // tWR ns Write recovery time
|
|
parameter tWTR = 1.0; // tWTR tCK Internal Write-to-Read command delay
|
|
parameter tXP = 6.0; // tXP ns Exit power-down to first valid cmd
|
|
`else `define sg75 // Timing Parameters for -75 (CL = 3)
|
|
parameter tAC3_max = 6.0; // tAC ns Access window of DQ from CK/CK#
|
|
parameter tAC2_max = 6.5; // tAC ns Access window of DQ from CK/CK#
|
|
parameter tCK = 7.5; // tCK ns Nominal Clock Cycle Time
|
|
parameter tCK3_min = 7.5; // tCK ns Nominal Clock Cycle Time
|
|
parameter tCK2_min = 12.0; // tCK ns Nominal Clock Cycle Time
|
|
parameter tDQSQ = 0.60; // tDQSQ ns DQS-DQ skew, DQS to last DQ valid, per group, per access
|
|
parameter tHZ3_max = 6.0; // tHZ ns Data-out high Z window from CK/CK#
|
|
parameter tHZ2_max = 6.5; // tHZ ns Data-out high Z window from CK/CK#
|
|
parameter tRAS = 45.0; // tRAS ns Active to Precharge command time
|
|
parameter tRC = 75.0; // tRC ns Active to Active/Auto Refresh command time
|
|
parameter tRCD = 22.5; // tRCD ns Active to Read/Write command time
|
|
parameter tRP = 22.5; // tRP ns Precharge command period
|
|
parameter tRRD = 15.0; // tRRD ns Active bank a to Active bank b command time
|
|
parameter tWR = 15.0; // tWR ns Write recovery time
|
|
parameter tWTR = 1.0; // tWTR tCK Internal Write-to-Read command delay
|
|
parameter tXP = 7.5; // tXP ns Exit power-down to first valid cmd
|
|
`endif
|
|
|
|
parameter tAC2_min = 2.0; // tAC ns Access window of DQ from CK/CK#
|
|
parameter tAC3_min = 2.0; // tAC ns Access window of DQ from CK/CK#
|
|
parameter tLZ = 1.0; // tLZ ns Data-out low Z window from CK/CK#
|
|
parameter tMRD = 2.0; // tMRD tCK Load Mode Register command cycle time
|
|
parameter tRFC = 70.0; // tRFC ns Refresh to Refresh Command interval time
|
|
parameter tSRC = 1.0; // tSRC tCK SRR READ command to first valid command (Not Applicable for 128Mb, 256Mb, and 512Mb Parts)
|
|
parameter tSRR = 2.0; // tSRR tCK SRR command to SRR READ command (Not Applicable for 128Mb, 256Mb, and 512Mb Parts)
|
|
|
|
// Size Parameters based on Part Width
|
|
`ifdef x16
|
|
parameter ADDR_BITS = 13; // Set this parameter to control how many Address bits are used
|
|
parameter ROW_BITS = 13; // Set this parameter to control how many Row bits are used
|
|
parameter DQ_BITS = 16; // Set this parameter to control how many Data bits are used
|
|
parameter DQS_BITS = 2; // Set this parameter to control how many DQS bits are used
|
|
parameter DM_BITS = 2; // Set this parameter to control how many DM bits are used
|
|
parameter COL_BITS = 9; // Set this parameter to control how many Column bits are used
|
|
parameter BA_BITS = 2; // Bank bits
|
|
`else `define x32
|
|
`ifdef RP
|
|
parameter ADDR_BITS = 13; // Set this parameter to control how many Address bits are used
|
|
parameter ROW_BITS = 13; // Set this parameter to control how many Row bits are used
|
|
parameter DQ_BITS = 32; // Set this parameter to control how many Data bits are used
|
|
parameter DQS_BITS = 4; // Set this parameter to control how many DQS bits are used
|
|
parameter DM_BITS = 4; // Set this parameter to control how many DM bits are used
|
|
parameter COL_BITS = 8; // Set this parameter to control how many Column bits are used
|
|
parameter BA_BITS = 2; // Bank bits
|
|
`else
|
|
parameter ADDR_BITS = 12; // Set this parameter to control how many Address bits are used
|
|
parameter ROW_BITS = 12; // Set this parameter to control how many Row bits are used
|
|
parameter DQ_BITS = 32; // Set this parameter to control how many Data bits are used
|
|
parameter DQS_BITS = 4; // Set this parameter to control how many DQS bits are used
|
|
parameter DM_BITS = 4; // Set this parameter to control how many DM bits are used
|
|
parameter COL_BITS = 9; // Set this parameter to control how many Column bits are used
|
|
parameter BA_BITS = 2; // Bank bits
|
|
`endif
|
|
`endif
|
|
|
|
// For use with the Multi Chip Package
|
|
`ifdef DUAL_RANK
|
|
parameter CS_BITS = 2; // Set this parameter to control how many Chip Select bits are used
|
|
parameter RANKS = 2; // Set this parameter to control how many Ranks on the mcp are used
|
|
`else
|
|
parameter CS_BITS = 2; // Set this parameter to control how many Chip Select bits are used
|
|
parameter RANKS = 1; // Set this parameter to control how many Ranks on the mcp are used
|
|
`endif
|
|
|
|
parameter full_mem_bits = BA_BITS+ADDR_BITS+COL_BITS; // Set this parameter to control how many unique addresses are used
|
|
parameter part_mem_bits = 10; // For fast sim load
|
|
parameter part_size = 256; // Set this parameter to indicate part size(512Mb, 256Mb, 128Mb)
|
|
parameter tCH_MAX = 0.55; // Clk high level width
|
|
parameter tCH_MIN = 0.45; // Clk high level width
|
|
parameter tCL_MAX = 0.55; // Clk low level width
|
|
parameter tCL_MIN = 0.45; // Clk low level width
|
|
parameter tCKE = 2.0; // Minimum tCKE High/Low time (in tCK's)
|
|
parameter CL_MAX = 3; // Maximum CAS Latency
|
|
parameter BL_MAX = 16;
|
|
|
|
|