90 lines
3.5 KiB
Plaintext
Executable File
90 lines
3.5 KiB
Plaintext
Executable File
# netif.options:
|
|
#
|
|
# The network startup script, /etc/init.d/network, computes typical
|
|
# primary and gateway interface names and addresses for most systems.
|
|
# Netif.options provides a place for site-dependent network interface
|
|
# definitions. You need to modify this file only if:
|
|
# 1) the computed primary and/or gateway interface names are incorrect, or
|
|
# 2) you don't like the convention used to define addresses for interfaces, or
|
|
# 3) the host has more than 2 interfaces.
|
|
#
|
|
# /etc/init.d/network uses two variables to configure each interface.
|
|
# The script uses "if1name" and "if1addr" for the primary interface,
|
|
# "if2name" and "if2addr" for the first gateway interface, etc.
|
|
# By default, when an fddi interface is present, the network sets it
|
|
# to be the primary interface (if1name) and the primary ethernet interface
|
|
# to be the secondary (if2name). If you do not want this behavior, you
|
|
# must explictly set both if1name and if2name in this file, not just
|
|
# if1name (see below).
|
|
#
|
|
# An ifXname variable (where X=1,2,3...) is the interface's device name as
|
|
# reported by "/usr/etc/netstat -i". Valid names include ef0, eg0,
|
|
# rns0, rns1, ipg0, ipg1, atm0, atm1, etc., but NOT lo0.
|
|
#
|
|
# An ifXaddr variable is a hostname containing $HOSTNAME or a hostname
|
|
# in /etc/hosts or an IP address in dot notation. ($HOSTNAME is the host's
|
|
# name in /etc/sys_id.) By convention, gateway interfaces use the
|
|
# "gate-", "gate2-" and "gate3-" prefixes in front of $HOSTNAME.
|
|
# If you don't like this convention, change the appropriate ifXaddr variables.
|
|
# For the system to boot correctly, make sure that names specified in ifXaddr
|
|
# variables have entries in /etc/hosts.
|
|
|
|
# IMPORTANT: any ifXname variables not defined, or commented out, in
|
|
# /etc/config/netif.options will retain their default values chosen
|
|
# by the network startup script. Care should be taken not to assign
|
|
# such a default value to another ifXname without ensuring that the
|
|
# ifXname also referencing this interface is assigned a different
|
|
# name, since this can lead to unexpected results and possible loss
|
|
# of network connectivity. As an example, on a system which has
|
|
# an et interface and an ipg interface, the following netif.options
|
|
# would be wrong:
|
|
#
|
|
# # if1name commented out
|
|
# #if1name=ef0
|
|
# #if1addr=192.0.0.1
|
|
# # define if2name to be FDDI
|
|
# if2name=rns0
|
|
# if2addr=192.0.1.1
|
|
#
|
|
# since the system would choose the rns FDDI interface to be the default
|
|
# value for if1name and would subsequently try to configure it twice;
|
|
# as if1name and if2name.
|
|
|
|
|
|
# The following shell variables have the form "var=value", with no spaces
|
|
# before or after the = character (for example: if1name=fxp1).
|
|
# Lines with the leading : character are commented out.
|
|
|
|
|
|
# Append the interface name and remove the leading : to override
|
|
# the primary interface selection.
|
|
|
|
: if1name=
|
|
|
|
# To override the primary interface address, change the value part
|
|
# and remove the leading : character.
|
|
|
|
: if1addr=$HOSTNAME
|
|
|
|
# To override the name and/or address of the first gateway interface,
|
|
# change the value part and remove the leading : character.
|
|
|
|
: if2name=
|
|
: if2addr=gate-$HOSTNAME
|
|
|
|
# If this host has more than 2 interfaces, you must define values for
|
|
# if3name (and if4name if appropriate). Change if3addr (and if4addr) to
|
|
# the appropriate names in /etc/hosts if your site has different naming
|
|
# conventions.
|
|
|
|
if3name=
|
|
if3addr=gate2-$HOSTNAME
|
|
|
|
if4name=
|
|
if4addr=gate3-$HOSTNAME
|
|
|
|
# If this host has more than 8 network interfaces, set the number of
|
|
# interfaces that the network startup script will configure.
|
|
|
|
: if_num=8
|