2011-05-18 20:25:54 +03:00
|
|
|
<TITLE>Production and testing: Fault analysis</TITLE>
|
|
|
|
|
<BODY>
|
|
|
|
|
<HTML>
|
|
|
|
|
<H1>Production and testing: Fault analysis</H1>
|
|
|
|
|
|
|
|
|
|
|
2011-05-18 20:43:45 +03:00
|
|
|
<!-- ====================================================================== -->
|
2011-05-18 20:25:54 +03:00
|
|
|
|
|
|
|
|
|
2011-05-18 20:43:45 +03:00
|
|
|
<H2>Component placement and orientation</H2>
|
2011-05-18 20:25:54 +03:00
|
|
|
|
|
|
|
|
|
2011-05-18 20:43:45 +03:00
|
|
|
<!-- ====================================================================== -->
|
2011-05-18 20:25:54 +03:00
|
|
|
|
|
|
|
|
|
2011-05-18 20:43:45 +03:00
|
|
|
<H2>Supply voltages</H2>
|
|
|
|
|
|
2011-05-18 20:25:54 +03:00
|
|
|
|
2011-05-18 20:43:45 +03:00
|
|
|
<!-- ====================================================================== -->
|
2011-05-18 20:25:54 +03:00
|
|
|
|
2011-05-18 20:43:45 +03:00
|
|
|
|
|
|
|
|
<H2>Clock frequency</H2>
|
2011-05-18 20:25:54 +03:00
|
|
|
|
|
|
|
|
The flawless performance of the crystal oscillator is crucial for
|
|
|
|
|
operation. Anomalies are easy to detect with even a low-cost oscilloscope
|
|
|
|
|
and pinpoint specific problems and help to select further analysis steps.
|
|
|
|
|
<P>
|
|
|
|
|
The crystal used in <B>atben</B> and <B>atusb</B> has a nominal tolerance
|
|
|
|
|
of +/- 15 ppm at 22-28 C. Low-cost oscilloscopes typically have a timing
|
|
|
|
|
accuracy of
|
|
|
|
|
+/- 100 ppm, which means that only major excursions can be detected by
|
|
|
|
|
measuring the clock output with such an instrument. Full-speed USB only
|
|
|
|
|
requires an accuracy of +/- 2500 ppm.
|
|
|
|
|
We can therefore consider all results within a range of +/- 1000 ppm as
|
|
|
|
|
sufficient, and perform more precise measurements by other means. This
|
|
|
|
|
applies to <B>atben</B> as well as to <B>atusb</B>.
|
|
|
|
|
<P>
|
|
|
|
|
|
|
|
|
|
|
2011-05-18 20:43:45 +03:00
|
|
|
<!-- ---------------------------------------------------------------------- -->
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
<H3>Measuring the clock on atben</H3>
|
2011-05-18 20:25:54 +03:00
|
|
|
|
|
|
|
|
<B>atben</B> normally does not output a clock signal. A 1 MHz clock
|
|
|
|
|
can be enabled with the following command:
|
|
|
|
|
<PRE>
|
|
|
|
|
atrf-txrx -d net:ben -C 1
|
|
|
|
|
</PRE>
|
|
|
|
|
This configures <B>atben</B> as a promiscuous receiver. The reception
|
|
|
|
|
of any IEEE 802.15.4 frame or pressing Ctrl-C will terminate the command.
|
|
|
|
|
<P>
|
|
|
|
|
<TABLE>
|
|
|
|
|
<TR><TH align="left">Clock<TH align="left">Action
|
|
|
|
|
<TR><TD>0 Hz<TD>Check voltages; check that the clock is enabled;
|
|
|
|
|
check for shorts around crystal; check connectivity of crystal
|
|
|
|
|
<TR><TD>0.999-1.001 MHz, ~3.3 Vpp<TD>Perform precision measurement with
|
|
|
|
|
<B>atrf-xtal</B>
|
|
|
|
|
<TR><TD>Other<TD>Check voltages; check for contamination around crystal
|
|
|
|
|
</TABLE>
|
|
|
|
|
<P>
|
|
|
|
|
|
|
|
|
|
|
2011-05-18 20:43:45 +03:00
|
|
|
<!-- ---------------------------------------------------------------------- -->
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
<H3>Measuring the clock on atusb</H3>
|
2011-05-18 20:25:54 +03:00
|
|
|
|
|
|
|
|
The transceiver provides the clock for the microcontroller in <B>atusb</B>.
|
|
|
|
|
A clock signal is therefore always available. Immediately after reset,
|
|
|
|
|
the transceiver generates a 1 MHz clock. When the microcontrolled comes out
|
|
|
|
|
of reset, it raises the transceiver's clock output to 8 MHz and then
|
|
|
|
|
enables USB.
|
|
|
|
|
<P>
|
|
|
|
|
<TABLE>
|
|
|
|
|
<TR><TH align="left">Clock<TH align="left">Action
|
|
|
|
|
<TR><TD>0 Hz<TD>Check voltages; check for shorts around crystal; check
|
|
|
|
|
connectivity of crystal
|
|
|
|
|
<TR><TD>0.999-1.001 MHz, ~3.3 Vpp<TD>Check presence of firmware; check for
|
|
|
|
|
shorts on SPI signals; check connectivity of SPI signals
|
|
|
|
|
<TR><TD>7.992-8.008 MHz, ~3.3 Vpp<TD>Perform precision measurement with
|
|
|
|
|
<B>atrf-xtal</B>
|
|
|
|
|
<TR><TD>Other<TD>Check voltages; check for contamination around crystal
|
|
|
|
|
</TABLE>
|
|
|
|
|
|
|
|
|
|
|
2011-05-18 20:43:45 +03:00
|
|
|
<!-- ---------------------------------------------------------------------- -->
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
<H3>Precision measurements</H3>
|
2011-05-18 20:25:54 +03:00
|
|
|
|
|
|
|
|
<P>
|
|
|
|
|
<HR>
|
|
|
|
|
Last update: 2011-05-18 <I>Werner Almesberger</I>
|
|
|
|
|
<HR>
|
|
|
|
|
</BODY>
|
|
|
|
|
</HTML>
|
