mirror of
git://projects.qi-hardware.com/ben-wpan.git
synced 2024-12-23 13:56:47 +02:00
3cc92cc4a6
The measured values are: board idle, looping 9 mA LED on + 5 mA TX CW (+3 dBm) +14 mA ------ 28 mA ====== Adding a margin of 12 mA, we get 40 mA. DFU used 30 mA so far, the application 50 mA. - board.h (BOARD_MAX_mA): define maximum USB bus current - descr.c (config_descriptor), usb/dfu.c (config_descriptor): use BOARD_MAX_mA for bMaxPower instead of hard-coding values |
||
|---|---|---|
| .. | ||
| an | ||
| include | ||
| usb | ||
| atusb.c | ||
| board_app.c | ||
| board.c | ||
| board.h | ||
| boot.c | ||
| descr.c | ||
| ep0.c | ||
| flash.c | ||
| Makefile | ||
| README | ||
| sernum.c | ||
| sernum.h | ||
| spi.c | ||
| spi.h | ||
| version.h | ||
Requires a very recent toolchain, because ATmega32U2 is relatively new.
- Building:
make
- Uploading the firmware to a Ben (for flashing with the atusb-pgm cable):
make HOST=<hostname> upload
Example:
make HOST=ben upload
HOST defaults to "jlime".
- Flashing the boot loader:
Prerequisite: avrdude on the Ben.
Disconnect the atusb board from USB. Insert the atusb-pgm connector into
the Ben. Place the atusb-pgm adapter on the exposed contact pads of the
atusb board and push it down. Then run
make prog
This takes about 30 seconds. If the programming fails with an error
message like "Yikes! Invalid device signature.", verify that the
atusb-pgm board is properly connected and placed, then try again.
- Uploading the application:
Prerequisite: dfu-util installed on the PC.
Insert atusb into the PC, then run
make dfu
Note: since the boot loader resets the USB bus after timing out,
this operation can fail with a message like "No DFU capable USB device
found". Just retry, and it will eventually get through.
--------------------------
Making the toolchain:
# patches according to
# http://www.avrfreaks.net/index.php?name=PNphpBB2&file=viewtopic&p=789527
# some gcc prerequisites
apt-get remove avr-libc gcc-avr binutils-avr
apt-get install libmpfr-dev libmpc-dev
# binutils
wget http://ftp.gnu.org/gnu/binutils/binutils-2.21.tar.bz2
tar xfj binutils-2.21.tar.bz2
cd binutils-2.21
./configure --target=avr --disable-nls
make
make install
# gcc
wget http://ftpmirror.gnu.org/gcc/gcc-4.5.2/gcc-4.5.2.tar.bz2
wget -O gcc_452_avr.patch http://gcc.gnu.org/bugzilla/attachment.cgi?id=23050
tar xfj gcc-4.5.2.tar.bz2
cd gcc-4.5.2
patch -p1 -s <../gcc_452_avr.patch
mkdir obj-avr
cd obj-avr
../configure --target=avr --enable-languages=c \
--disable-nls --disable-libssp --with-dwarf2
make
make install
wget http://download.savannah.gnu.org/releases/avr-libc/avr-libc-1.7.1.tar.bz2
tar xfj avr-libc-1.7.1.tar.bz2
cd avr-libc-1.7.1
./bootstrap # the automake at the end takes a while
./configure --build=`./config.guess` --host=avr
make
make install