mv binary files to sie_rootfs_files/

Signed-off-by: Xiangfu Liu <xiangfu@sharism.cc>

binaries/sie_rootfs_files/etc/init.d/start

@@ -0,0 +1,5 @@
+#!/bin/sh
+/usr/bin/xc3sprog /root/binaries/ADC.bit &
+/usr/bin/sgen -f 1000 &
+/root/binaries/ADC -qws -nomouse &
+

binaries/sie_rootfs_files/etc/inittab

@@ -0,0 +1,8 @@
+::sysinit:/etc/init.d/rcS S boot
+::shutdown:/etc/init.d/rcS K stop
+tts/0::askfirst:/bin/ash --login
+#ttyS0::askfirst:/bin/ash --login
+tty1::askfirst:/bin/ash --login
+tty2::askfirst:/bin/ash --login
+tty3::askfirst:/bin/ash --login
+tty4::askfirst:/bin/ash --login

binaries/sie_rootfs_files/root/binaries/flash_kernel.sh

@@ -0,0 +1,3 @@
+#!/bin/bash
+sudo usbboot -f ./usbboot_2gb_nand.cfg  -c "boot"
+sudo usbboot -f ./usbboot_2gb_nand.cfg  -c "nprog 1024 openwrt-xburst-qi_lb60-uImage.bin 0 0 -n"

binaries/sie_rootfs_files/root/binaries/load_u-boot.sh

@@ -0,0 +1,2 @@
+sudo usbboot -f ./usbboot_2gb_nand.cfg -c "boot"
+sudo usbboot -f ./usbboot_2gb_nand.cfg  -c "nprog 0 openwrt-xburst-qi_lb60-u-boot.bin 0 0 -n" 

binaries/sie_rootfs_files/root/binaries/program_rootfs.sh

@@ -0,0 +1,4 @@
+#!/bin/bash
+ROOTFS=openwrt-xburst-qi_lb60-root.ubi
+sudo usbboot -f ./usbboot_2gb_nand.cfg  -c "boot"
+sudo usbboot -f ./usbboot_2gb_nand.cfg  -c "nprog 2048 $ROOTFS 0 0 -n"

binaries/sie_rootfs_files/root/binaries/usbboot_2gb_nand.cfg

@@ -0,0 +1,59 @@
+#
+# usbboot configuration file
+#
+# Utility to respond to the Ingenic XBurst USB boot protocol, provide
+# initial boot stages and ability to access NAND on device.
+#
+# Authors: Ingenic Semiconductor, Inc.
+#          Xiangfu Liu <xiangfu@qi-hardware.com>
+#          Marek Lindner <lindner_marek@yahoo.de>
+#          Wolfgang Spraul <wolfgang@qi-hardware.com>
+#
+# This program is free software: you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation, either version 3 of the License, or
+# (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+# [PLL]
+EXTCLK = 12	#Define the external crystal in MHz
+CPUSPEED = 252	#Define the PLL output frequency
+PHMDIV = 3	#Define the frequency divider ratio of PLL=CCLK:PCLK=HCLK=MCLK
+BOUDRATE = 57600	#Define the uart boudrate
+USEUART = 0	#Use which uart, 0/1 for jz4740,0/1/2/3 for jz4750
+
+# [SDRAM]
+BUSWIDTH = 16	#The bus width of the SDRAM in bits (16|32)
+BANKS = 4	#The bank number (2|4)
+ROWADDR = 13	#Row address width in bits (11-13)
+COLADDR = 9	#Column address width in bits (8-12)
+ISMOBILE = 0	#Define whether SDRAM is mobile SDRAM, this only valid for Jz4750 ,1:yes 0:no
+ISBUSSHARE = 1	#Define whether SDRAM bus share with NAND 1:shared 0:unshared
+DEBUGOPS = 0
+
+# [NAND]
+NAND_BUSWIDTH = 8	#The width of the NAND flash chip in bits (8|16|32)
+NAND_ROWCYCLES = 3	#The row address cycles (2|3)
+NAND_PAGESIZE = 4096	#The page size of the NAND chip in bytes(512|2048|4096)
+NAND_PAGEPERBLOCK = 128	#The page number per block
+NAND_FORCEERASE = 1	#The force to erase flag (0|1)
+NAND_OOBSIZE = 128	#oob size in byte
+NAND_ECCPOS = 12	#Specify the ECC offset inside the oob data (0-[oobsize-1])
+NAND_BADBLOCKPOS = 0	#Specify the badblock flag offset inside the oob (0-[oobsize-1])
+NAND_BADBLOCKPAGE = 127	#Specify the page number of badblock flag inside a block(0-[PAGEPERBLOCK-1])
+NAND_PLANENUM = 1	#The planes number of target nand flash
+NAND_BCHBIT = 4		#Specify the hardware BCH algorithm for 4750 (4|8)
+NAND_WPPIN = 0		#Specify the write protect pin number
+NAND_BLOCKPERCHIP = 0	#Specify the block number per chip,0 means ignore
+
+#The program will calculate the total SDRAM size by : size = 2^(ROWADDR + COLADDR) * BANKNUM * (SDRAMWIDTH / 4)
+#The CPUSPEED has restriction as: ( CPUSPEED % EXTCLK == 0 ) && ( CPUSPEED % 12 == 0 )
+#For jz4750, the program just init BANK0(DSC0).
+#Beware all variables must be set correct!

binaries/sie_rootfs_files/usr/share/xc3sprog/devlist.txt

@@ -0,0 +1,20 @@
+# IDCODE    IR Length	Text
+0140d093	6	XC3S50
+01414093	6	XC3S200
+0141c093	6	XC3S400
+01428093	6	XC3S1000
+01434093	6	XC3S1500
+01440093	6	XC3S2000
+01448093	6	XC3S4000
+01450093	6	XC3S5000
+05045093	8	XCF02S
+00608093	5	XC2S15
+0060c093	5	XC2S30
+00610093	5	XC2S50
+00614093	5	XC2S100
+00618093	5	XC2S150
+0061c093	5	XC2S200
+11c10093        6       XC3S100E
+11c1a093        6       XC3S250E
+41c22093	6	XC3S500E
+