1
0
mirror of git://projects.qi-hardware.com/openwrt-xburst.git synced 2024-12-24 07:29:33 +02:00

adm5120: add 3.3 support

Partially based on the 3.1 patches by Hartmut Knaack <knaack.h [at] gmx.de>

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31474 3c298f89-4303-0410-b956-a3cf2f4a3e73
This commit is contained in:
juhosg 2012-04-25 12:57:33 +00:00
parent 0e8ddda2ee
commit 05735d303b
26 changed files with 2841 additions and 0 deletions

View File

@ -0,0 +1,43 @@
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -39,6 +39,23 @@ choice
prompt "System type"
default SGI_IP22
+config ADM5120
+ bool "Infineon/ADMtek ADM5120 SoC based machines"
+ select BOOT_RAW
+ select NO_EXCEPT_FILL
+ select CEVT_R4K
+ select CSRC_R4K
+ select SYS_HAS_CPU_MIPS32_R1
+ select SYS_HAS_EARLY_PRINTK
+ select DMA_NONCOHERENT
+ select IRQ_CPU
+ select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_SUPPORTS_BIG_ENDIAN
+ select SYS_SUPPORTS_32BIT_KERNEL
+ select ARCH_REQUIRE_GPIOLIB
+ select SWAP_IO_SPACE if CPU_BIG_ENDIAN
+ select MIPS_MACHINE
+
config MIPS_ALCHEMY
bool "Alchemy processor based machines"
select 64BIT_PHYS_ADDR
@@ -813,6 +830,7 @@ config NLM_XLP_BOARD
endchoice
+source "arch/mips/adm5120/Kconfig"
source "arch/mips/alchemy/Kconfig"
source "arch/mips/ath79/Kconfig"
source "arch/mips/bcm47xx/Kconfig"
--- a/arch/mips/Kbuild.platforms
+++ b/arch/mips/Kbuild.platforms
@@ -1,5 +1,6 @@
# All platforms listed in alphabetic order
+platforms += adm5120
platforms += alchemy
platforms += ar7
platforms += ath79

View File

@ -0,0 +1,21 @@
--- a/drivers/mtd/maps/Kconfig
+++ b/drivers/mtd/maps/Kconfig
@@ -526,4 +526,8 @@ config MTD_LATCH_ADDR
If compiled as a module, it will be called latch-addr-flash.
+config MTD_ADM5120
+ tristate "Map driver for ADM5120 based boards"
+ depends on ADM5120
+
endmenu
--- a/drivers/mtd/maps/Makefile
+++ b/drivers/mtd/maps/Makefile
@@ -38,6 +38,7 @@ obj-$(CONFIG_MTD_SCx200_DOCFLASH)+= scx2
obj-$(CONFIG_MTD_DBOX2) += dbox2-flash.o
obj-$(CONFIG_MTD_SOLUTIONENGINE)+= solutionengine.o
obj-$(CONFIG_MTD_PCI) += pci.o
+obj-$(CONFIG_MTD_ADM5120) += adm5120-flash.o
obj-$(CONFIG_MTD_AUTCPU12) += autcpu12-nvram.o
obj-$(CONFIG_MTD_IMPA7) += impa7.o
obj-$(CONFIG_MTD_FORTUNET) += fortunet.o

View File

@ -0,0 +1,23 @@
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -247,6 +247,10 @@ source "drivers/net/dsa/Kconfig"
source "drivers/net/ethernet/Kconfig"
+config ADM5120_ENET
+ tristate "ADM5120 Ethernet switch support"
+ depends on ADM5120
+
source "drivers/net/fddi/Kconfig"
source "drivers/net/hippi/Kconfig"
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -32,6 +32,7 @@ obj-$(CONFIG_CAN) += can/
obj-$(CONFIG_ETRAX_ETHERNET) += cris/
obj-$(CONFIG_NET_DSA) += dsa/
obj-$(CONFIG_ETHERNET) += ethernet/
+obj-$(CONFIG_ADM5120_ENET) += adm5120sw.o
obj-$(CONFIG_FDDI) += fddi/
obj-$(CONFIG_HIPPI) += hippi/
obj-$(CONFIG_HAMRADIO) += hamradio/

View File

@ -0,0 +1,33 @@
--- a/drivers/usb/Makefile
+++ b/drivers/usb/Makefile
@@ -13,6 +13,7 @@ obj-$(CONFIG_USB_DWC3) += dwc3/
obj-$(CONFIG_USB_MON) += mon/
obj-$(CONFIG_PCI) += host/
+obj-$(CONFIG_USB_ADM5120_HCD) += host/
obj-$(CONFIG_USB_EHCI_HCD) += host/
obj-$(CONFIG_USB_ISP116X_HCD) += host/
obj-$(CONFIG_USB_OHCI_HCD) += host/
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -4,6 +4,10 @@
comment "USB Host Controller Drivers"
depends on USB
+config USB_ADM5120_HCD
+ tristate "ADM5120 HCD support (EXPERIMENTAL)"
+ depends on USB && ADM5120 && EXPERIMENTAL
+
config USB_C67X00_HCD
tristate "Cypress C67x00 HCD support"
depends on USB
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -19,6 +19,7 @@ obj-$(CONFIG_USB_WHCI_HCD) += whci/
obj-$(CONFIG_PCI) += pci-quirks.o
+obj-$(CONFIG_USB_ADM5120_HCD) += adm5120-hcd.o
obj-$(CONFIG_USB_EHCI_HCD) += ehci-hcd.o
obj-$(CONFIG_USB_OXU210HP_HCD) += oxu210hp-hcd.o
obj-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o

View File

@ -0,0 +1,22 @@
--- a/arch/mips/pci/Makefile
+++ b/arch/mips/pci/Makefile
@@ -20,6 +20,7 @@ obj-$(CONFIG_BCM63XX) += pci-bcm63xx.o
ops-bcm63xx.o
obj-$(CONFIG_MIPS_ALCHEMY) += pci-alchemy.o
obj-$(CONFIG_SOC_AR724X) += pci-ath724x.o
+obj-$(CONFIG_ADM5120) += pci-adm5120.o
#
# These are still pretty much in the old state, watch, go blind.
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -1803,6 +1803,9 @@
#define PCI_VENDOR_ID_ESDGMBH 0x12fe
#define PCI_DEVICE_ID_ESDGMBH_CPCIASIO4 0x0111
+#define PCI_VENDOR_ID_ADMTEK 0x1317
+#define PCI_DEVICE_ID_ADMTEK_ADM5120 0x5120
+
#define PCI_VENDOR_ID_SIIG 0x131f
#define PCI_SUBVENDOR_ID_SIIG 0x131f
#define PCI_DEVICE_ID_SIIG_1S_10x_550 0x1000

View File

@ -0,0 +1,22 @@
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -498,4 +498,12 @@ config LEDS_TRIGGER_USBDEV
This allows LEDs to be controlled by the presence/activity of
an USB device. If unsure, say N.
+config LEDS_TRIGGER_ADM5120_SWITCH
+ tristate "LED ADM5120 Switch Port Status Trigger"
+ depends on LEDS_TRIGGERS && ADM5120
+ help
+ This allows LEDs to be controlled by the port states of
+ the ADM5120 built-in Ethernet Switch
+ If unsure, say N.
+
endif # NEW_LEDS
--- a/drivers/leds/Makefile
+++ b/drivers/leds/Makefile
@@ -60,3 +60,4 @@ obj-$(CONFIG_LEDS_TRIGGER_DEFAULT_ON) +=
obj-$(CONFIG_LEDS_TRIGGER_MORSE) += ledtrig-morse.o
obj-$(CONFIG_LEDS_TRIGGER_NETDEV) += ledtrig-netdev.o
obj-$(CONFIG_LEDS_TRIGGER_USBDEV) += ledtrig-usbdev.o
+obj-$(CONFIG_LEDS_TRIGGER_ADM5120_SWITCH) += ledtrig-adm5120-switch.o

View File

@ -0,0 +1,84 @@
--- a/drivers/mtd/chips/cfi_cmdset_0002.c
+++ b/drivers/mtd/chips/cfi_cmdset_0002.c
@@ -48,6 +48,12 @@
#define SST49LF008A 0x005a
#define AT49BV6416 0x00d6
+/* Macronix */
+#define MX29LV160B 0x2249 /* MX29LV160 Bottom-boot chip */
+#define MX29LV160T 0x22C4 /* MX29LV160 Top-boot chip */
+#define MX29LV320B 0x22A8 /* MX29LV320 Bottom-boot chip */
+#define MX29LV320T 0x22A7 /* MX29LV320 Top-boot chip */
+
static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *);
static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
@@ -342,6 +348,41 @@ static struct cfi_fixup cfi_nopri_fixup_
{ 0, 0, NULL }
};
+#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
+/*
+ * Some Macronix chips has no/bad bootblock information in the CFI table
+ */
+static void fixup_macronix_bootloc(struct mtd_info *mtd, void* param)
+{
+ struct map_info *map = mtd->priv;
+ struct cfi_private *cfi = map->fldrv_priv;
+ struct cfi_pri_amdstd *extp = cfi->cmdset_priv;
+ __u8 t;
+
+ switch (cfi->id) {
+ /* TODO: put affected chip ids here */
+ case MX29LV160B:
+ case MX29LV320B:
+ t = 2; /* Bottom boot */
+ break;
+ case MX29LV160T:
+ case MX29LV320T:
+ t = 3; /* Top boot */
+ break;
+ default:
+ return;
+ }
+
+ if (extp->TopBottom == t)
+ /* boot location detected by the CFI layer is correct */
+ return;
+
+ extp->TopBottom = t;
+ printk("%s: Macronix chip detected, id:0x%04X, boot location forced "
+ "to %s\n", map->name, cfi->id, (t == 2) ? "bottom" : "top");
+}
+#endif /* CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC */
+
static struct cfi_fixup cfi_fixup_table[] = {
{ CFI_MFR_ATMEL, CFI_ID_ANY, fixup_convert_atmel_pri },
#ifdef AMD_BOOTLOC_BUG
@@ -383,6 +424,9 @@ static struct cfi_fixup fixup_table[] =
*/
{ CFI_MFR_ANY, CFI_ID_ANY, fixup_use_erase_chip },
{ CFI_MFR_ATMEL, AT49BV6416, fixup_use_atmel_lock },
+#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
+ { CFI_MFR_MACRONIX, CFI_ID_ANY, fixup_macronix_bootloc, NULL, },
+#endif
{ 0, 0, NULL }
};
--- a/drivers/mtd/chips/Kconfig
+++ b/drivers/mtd/chips/Kconfig
@@ -196,6 +196,14 @@ config MTD_CFI_AMDSTD
provides support for one of those command sets, used on chips
including the AMD Am29LV320.
+config MTD_CFI_FIXUP_MACRONIX_BOOTLOC
+ bool "Fix boot-block location for Macronix flash chips"
+ depends on MTD_CFI_AMDSTD
+ help
+ Some Macronix flash chips have no/wrong boot-block location in the
+ CFI table, and the driver may detect the type incorrectly. Select
+ this if your board has such chip.
+
config MTD_CFI_STAA
tristate "Support for ST (Advanced Architecture) flash chips"
depends on MTD_GEN_PROBE

View File

@ -0,0 +1,68 @@
--- a/drivers/mtd/chips/jedec_probe.c
+++ b/drivers/mtd/chips/jedec_probe.c
@@ -115,6 +115,10 @@
#define UPD29F064115 0x221C
/* PMC */
+#define PM39LV512 0x001B
+#define PM39LV010 0x001C
+#define PM39LV020 0x003D
+#define PM39LV040 0x003E
#define PM49FL002 0x006D
#define PM49FL004 0x006E
#define PM49FL008 0x006A
@@ -1259,6 +1263,54 @@ static const struct amd_flash_info jedec
ERASEINFO(0x02000,2),
ERASEINFO(0x04000,1),
}
+ }, {
+ .mfr_id = CFI_MFR_PMC,
+ .dev_id = PM39LV512,
+ .name = "PMC Pm39LV512",
+ .devtypes = CFI_DEVICETYPE_X8,
+ .uaddr = MTD_UADDR_0x0555_0x02AA,
+ .dev_size = SIZE_64KiB,
+ .cmd_set = P_ID_AMD_STD,
+ .nr_regions = 1,
+ .regions = {
+ ERASEINFO(0x01000,16),
+ }
+ }, {
+ .mfr_id = CFI_MFR_PMC,
+ .dev_id = PM39LV010,
+ .name = "PMC Pm39LV010",
+ .devtypes = CFI_DEVICETYPE_X8,
+ .uaddr = MTD_UADDR_0x0555_0x02AA,
+ .dev_size = SIZE_128KiB,
+ .cmd_set = P_ID_AMD_STD,
+ .nr_regions = 1,
+ .regions = {
+ ERASEINFO(0x01000,32),
+ }
+ }, {
+ .mfr_id = CFI_MFR_PMC,
+ .dev_id = PM39LV020,
+ .name = "PMC Pm39LV020",
+ .devtypes = CFI_DEVICETYPE_X8,
+ .uaddr = MTD_UADDR_0x0555_0x02AA,
+ .dev_size = SIZE_256KiB,
+ .cmd_set = P_ID_AMD_STD,
+ .nr_regions = 1,
+ .regions = {
+ ERASEINFO(0x01000,64),
+ }
+ }, {
+ .mfr_id = CFI_MFR_PMC,
+ .dev_id = PM39LV040,
+ .name = "PMC Pm39LV040",
+ .devtypes = CFI_DEVICETYPE_X8,
+ .uaddr = MTD_UADDR_0x0555_0x02AA,
+ .dev_size = SIZE_512KiB,
+ .cmd_set = P_ID_AMD_STD,
+ .nr_regions = 1,
+ .regions = {
+ ERASEINFO(0x01000,128),
+ }
}, {
.mfr_id = CFI_MFR_PMC,
.dev_id = PM49FL002,

View File

@ -0,0 +1,23 @@
--- a/drivers/mtd/Kconfig
+++ b/drivers/mtd/Kconfig
@@ -31,6 +31,10 @@ config MTD_ROOTFS_SPLIT
bool "Automatically split 'rootfs' partition for squashfs"
default y
+config MTD_TRXSPLIT
+ bool "Automatically find and split TRX partitions"
+ default n
+
config MTD_REDBOOT_PARTS
tristate "RedBoot partition table parsing"
---help---
--- a/drivers/mtd/Makefile
+++ b/drivers/mtd/Makefile
@@ -13,6 +13,7 @@ obj-$(CONFIG_MTD_AFS_PARTS) += afs.o
obj-$(CONFIG_MTD_AR7_PARTS) += ar7part.o
obj-$(CONFIG_MTD_BCM63XX_PARTS) += bcm63xxpart.o
obj-$(CONFIG_MTD_MYLOADER_PARTS) += myloader.o
+obj-$(CONFIG_MTD_TRXSPLIT) += trxsplit.o
# 'Users' - code which presents functionality to userspace.
obj-$(CONFIG_MTD_CHAR) += mtdchar.o

View File

@ -0,0 +1,28 @@
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -88,6 +88,7 @@ obj-$(CONFIG_PATA_PCMCIA) += pata_pcmcia
obj-$(CONFIG_PATA_PALMLD) += pata_palmld.o
obj-$(CONFIG_PATA_PLATFORM) += pata_platform.o
obj-$(CONFIG_PATA_OF_PLATFORM) += pata_of_platform.o
+obj-$(CONFIG_PATA_RB153_CF) += pata_rb153_cf.o
obj-$(CONFIG_PATA_RB532) += pata_rb532_cf.o
obj-$(CONFIG_PATA_RZ1000) += pata_rz1000.o
obj-$(CONFIG_PATA_SAMSUNG_CF) += pata_samsung_cf.o
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -835,6 +835,15 @@ config PATA_QDI
help
Support for QDI 6500 and 6580 PATA controllers on VESA local bus.
+config PATA_RB153_CF
+ tristate "RouterBOARD 153 Compact Flash support"
+ depends on ADM5120_MACH_RB_153
+ help
+ This option enables support for a Compact Flash connected on
+ the RouterBOARD 153.
+
+ If unsure, say N.
+
config PATA_RB532
tristate "RouterBoard 532 PATA CompactFlash support"
depends on MIKROTIK_RB532

View File

@ -0,0 +1,378 @@
--- a/drivers/tty/serial/amba-pl010.c
+++ b/drivers/tty/serial/amba-pl010.c
@@ -49,11 +49,10 @@
#include <asm/io.h>
-#define UART_NR 8
-
#define SERIAL_AMBA_MAJOR 204
#define SERIAL_AMBA_MINOR 16
-#define SERIAL_AMBA_NR UART_NR
+#define SERIAL_AMBA_NR CONFIG_SERIAL_AMBA_PL010_NUMPORTS
+#define SERIAL_AMBA_NAME CONFIG_SERIAL_AMBA_PL010_PORTNAME
#define AMBA_ISR_PASS_LIMIT 256
@@ -79,9 +78,9 @@ static void pl010_stop_tx(struct uart_po
struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned int cr;
- cr = readb(uap->port.membase + UART010_CR);
+ cr = __raw_readl(uap->port.membase + UART010_CR);
cr &= ~UART010_CR_TIE;
- writel(cr, uap->port.membase + UART010_CR);
+ __raw_writel(cr, uap->port.membase + UART010_CR);
}
static void pl010_start_tx(struct uart_port *port)
@@ -89,9 +88,9 @@ static void pl010_start_tx(struct uart_p
struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned int cr;
- cr = readb(uap->port.membase + UART010_CR);
+ cr = __raw_readl(uap->port.membase + UART010_CR);
cr |= UART010_CR_TIE;
- writel(cr, uap->port.membase + UART010_CR);
+ __raw_writel(cr, uap->port.membase + UART010_CR);
}
static void pl010_stop_rx(struct uart_port *port)
@@ -99,9 +98,9 @@ static void pl010_stop_rx(struct uart_po
struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned int cr;
- cr = readb(uap->port.membase + UART010_CR);
+ cr = __raw_readl(uap->port.membase + UART010_CR);
cr &= ~(UART010_CR_RIE | UART010_CR_RTIE);
- writel(cr, uap->port.membase + UART010_CR);
+ __raw_writel(cr, uap->port.membase + UART010_CR);
}
static void pl010_enable_ms(struct uart_port *port)
@@ -109,9 +108,9 @@ static void pl010_enable_ms(struct uart_
struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned int cr;
- cr = readb(uap->port.membase + UART010_CR);
+ cr = __raw_readl(uap->port.membase + UART010_CR);
cr |= UART010_CR_MSIE;
- writel(cr, uap->port.membase + UART010_CR);
+ __raw_writel(cr, uap->port.membase + UART010_CR);
}
static void pl010_rx_chars(struct uart_amba_port *uap)
@@ -119,9 +118,9 @@ static void pl010_rx_chars(struct uart_a
struct tty_struct *tty = uap->port.state->port.tty;
unsigned int status, ch, flag, rsr, max_count = 256;
- status = readb(uap->port.membase + UART01x_FR);
+ status = __raw_readl(uap->port.membase + UART01x_FR);
while (UART_RX_DATA(status) && max_count--) {
- ch = readb(uap->port.membase + UART01x_DR);
+ ch = __raw_readl(uap->port.membase + UART01x_DR);
flag = TTY_NORMAL;
uap->port.icount.rx++;
@@ -130,9 +129,9 @@ static void pl010_rx_chars(struct uart_a
* Note that the error handling code is
* out of the main execution path
*/
- rsr = readb(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
+ rsr = __raw_readl(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
if (unlikely(rsr & UART01x_RSR_ANY)) {
- writel(0, uap->port.membase + UART01x_ECR);
+ __raw_writel(0, uap->port.membase + UART01x_ECR);
if (rsr & UART01x_RSR_BE) {
rsr &= ~(UART01x_RSR_FE | UART01x_RSR_PE);
@@ -162,7 +161,7 @@ static void pl010_rx_chars(struct uart_a
uart_insert_char(&uap->port, rsr, UART01x_RSR_OE, ch, flag);
ignore_char:
- status = readb(uap->port.membase + UART01x_FR);
+ status = __raw_readl(uap->port.membase + UART01x_FR);
}
spin_unlock(&uap->port.lock);
tty_flip_buffer_push(tty);
@@ -175,7 +174,7 @@ static void pl010_tx_chars(struct uart_a
int count;
if (uap->port.x_char) {
- writel(uap->port.x_char, uap->port.membase + UART01x_DR);
+ __raw_writel(uap->port.x_char, uap->port.membase + UART01x_DR);
uap->port.icount.tx++;
uap->port.x_char = 0;
return;
@@ -187,7 +186,7 @@ static void pl010_tx_chars(struct uart_a
count = uap->port.fifosize >> 1;
do {
- writel(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR);
+ __raw_writel(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
uap->port.icount.tx++;
if (uart_circ_empty(xmit))
@@ -205,9 +204,9 @@ static void pl010_modem_status(struct ua
{
unsigned int status, delta;
- writel(0, uap->port.membase + UART010_ICR);
+ __raw_writel(0, uap->port.membase + UART010_ICR);
- status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
+ status = __raw_readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
delta = status ^ uap->old_status;
uap->old_status = status;
@@ -235,7 +234,7 @@ static irqreturn_t pl010_int(int irq, vo
spin_lock(&uap->port.lock);
- status = readb(uap->port.membase + UART010_IIR);
+ status = __raw_readl(uap->port.membase + UART010_IIR);
if (status) {
do {
if (status & (UART010_IIR_RTIS | UART010_IIR_RIS))
@@ -248,7 +247,7 @@ static irqreturn_t pl010_int(int irq, vo
if (pass_counter-- == 0)
break;
- status = readb(uap->port.membase + UART010_IIR);
+ status = __raw_readl(uap->port.membase + UART010_IIR);
} while (status & (UART010_IIR_RTIS | UART010_IIR_RIS |
UART010_IIR_TIS));
handled = 1;
@@ -262,7 +261,7 @@ static irqreturn_t pl010_int(int irq, vo
static unsigned int pl010_tx_empty(struct uart_port *port)
{
struct uart_amba_port *uap = (struct uart_amba_port *)port;
- unsigned int status = readb(uap->port.membase + UART01x_FR);
+ unsigned int status = __raw_readl(uap->port.membase + UART01x_FR);
return status & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT;
}
@@ -272,7 +271,7 @@ static unsigned int pl010_get_mctrl(stru
unsigned int result = 0;
unsigned int status;
- status = readb(uap->port.membase + UART01x_FR);
+ status = __raw_readl(uap->port.membase + UART01x_FR);
if (status & UART01x_FR_DCD)
result |= TIOCM_CAR;
if (status & UART01x_FR_DSR)
@@ -298,12 +297,12 @@ static void pl010_break_ctl(struct uart_
unsigned int lcr_h;
spin_lock_irqsave(&uap->port.lock, flags);
- lcr_h = readb(uap->port.membase + UART010_LCRH);
+ lcr_h = __raw_readl(uap->port.membase + UART010_LCRH);
if (break_state == -1)
lcr_h |= UART01x_LCRH_BRK;
else
lcr_h &= ~UART01x_LCRH_BRK;
- writel(lcr_h, uap->port.membase + UART010_LCRH);
+ __raw_writel(lcr_h, uap->port.membase + UART010_LCRH);
spin_unlock_irqrestore(&uap->port.lock, flags);
}
@@ -335,12 +334,12 @@ static int pl010_startup(struct uart_por
/*
* initialise the old status of the modem signals
*/
- uap->old_status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
+ uap->old_status = __raw_readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
/*
* Finally, enable interrupts
*/
- writel(UART01x_CR_UARTEN | UART010_CR_RIE | UART010_CR_RTIE,
+ __raw_writel(UART01x_CR_UARTEN | UART010_CR_RIE | UART010_CR_RTIE,
uap->port.membase + UART010_CR);
return 0;
@@ -365,10 +364,10 @@ static void pl010_shutdown(struct uart_p
/*
* disable all interrupts, disable the port
*/
- writel(0, uap->port.membase + UART010_CR);
+ __raw_writel(0, uap->port.membase + UART010_CR);
/* disable break condition and fifos */
- writel(readb(uap->port.membase + UART010_LCRH) &
+ __raw_writel(__raw_readl(uap->port.membase + UART010_LCRH) &
~(UART01x_LCRH_BRK | UART01x_LCRH_FEN),
uap->port.membase + UART010_LCRH);
@@ -391,7 +390,7 @@ pl010_set_termios(struct uart_port *port
/*
* Ask the core to calculate the divisor for us.
*/
- baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16);
+ baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16);
quot = uart_get_divisor(port, baud);
switch (termios->c_cflag & CSIZE) {
@@ -454,25 +453,25 @@ pl010_set_termios(struct uart_port *port
uap->port.ignore_status_mask |= UART_DUMMY_RSR_RX;
/* first, disable everything */
- old_cr = readb(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
+ old_cr = __raw_readl(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
if (UART_ENABLE_MS(port, termios->c_cflag))
old_cr |= UART010_CR_MSIE;
- writel(0, uap->port.membase + UART010_CR);
+ __raw_writel(0, uap->port.membase + UART010_CR);
/* Set baud rate */
quot -= 1;
- writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM);
- writel(quot & 0xff, uap->port.membase + UART010_LCRL);
+ __raw_writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM);
+ __raw_writel(quot & 0xff, uap->port.membase + UART010_LCRL);
/*
* ----------v----------v----------v----------v-----
* NOTE: MUST BE WRITTEN AFTER UARTLCR_M & UARTLCR_L
* ----------^----------^----------^----------^-----
*/
- writel(lcr_h, uap->port.membase + UART010_LCRH);
- writel(old_cr, uap->port.membase + UART010_CR);
+ __raw_writel(lcr_h, uap->port.membase + UART010_LCRH);
+ __raw_writel(old_cr, uap->port.membase + UART010_CR);
spin_unlock_irqrestore(&uap->port.lock, flags);
}
@@ -554,7 +553,7 @@ static struct uart_ops amba_pl010_pops =
.verify_port = pl010_verify_port,
};
-static struct uart_amba_port *amba_ports[UART_NR];
+static struct uart_amba_port *amba_ports[SERIAL_AMBA_NR];
#ifdef CONFIG_SERIAL_AMBA_PL010_CONSOLE
@@ -564,10 +563,10 @@ static void pl010_console_putchar(struct
unsigned int status;
do {
- status = readb(uap->port.membase + UART01x_FR);
+ status = __raw_readl(uap->port.membase + UART01x_FR);
barrier();
} while (!UART_TX_READY(status));
- writel(ch, uap->port.membase + UART01x_DR);
+ __raw_writel(ch, uap->port.membase + UART01x_DR);
}
static void
@@ -581,8 +580,8 @@ pl010_console_write(struct console *co,
/*
* First save the CR then disable the interrupts
*/
- old_cr = readb(uap->port.membase + UART010_CR);
- writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR);
+ old_cr = __raw_readl(uap->port.membase + UART010_CR);
+ __raw_writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR);
uart_console_write(&uap->port, s, count, pl010_console_putchar);
@@ -591,10 +590,10 @@ pl010_console_write(struct console *co,
* and restore the TCR
*/
do {
- status = readb(uap->port.membase + UART01x_FR);
+ status = __raw_readl(uap->port.membase + UART01x_FR);
barrier();
} while (status & UART01x_FR_BUSY);
- writel(old_cr, uap->port.membase + UART010_CR);
+ __raw_writel(old_cr, uap->port.membase + UART010_CR);
clk_disable(uap->clk);
}
@@ -603,9 +602,9 @@ static void __init
pl010_console_get_options(struct uart_amba_port *uap, int *baud,
int *parity, int *bits)
{
- if (readb(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
+ if (__raw_readl(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
unsigned int lcr_h, quot;
- lcr_h = readb(uap->port.membase + UART010_LCRH);
+ lcr_h = __raw_readl(uap->port.membase + UART010_LCRH);
*parity = 'n';
if (lcr_h & UART01x_LCRH_PEN) {
@@ -620,8 +619,8 @@ pl010_console_get_options(struct uart_am
else
*bits = 8;
- quot = readb(uap->port.membase + UART010_LCRL) |
- readb(uap->port.membase + UART010_LCRM) << 8;
+ quot = __raw_readl(uap->port.membase + UART010_LCRL) |
+ __raw_readl(uap->port.membase + UART010_LCRM) << 8;
*baud = uap->port.uartclk / (16 * (quot + 1));
}
}
@@ -640,7 +639,7 @@ static int __init pl010_console_setup(st
* if so, search for the first available port that does have
* console support.
*/
- if (co->index >= UART_NR)
+ if (co->index >= SERIAL_AMBA_NR)
co->index = 0;
uap = amba_ports[co->index];
if (!uap)
@@ -662,7 +661,7 @@ static int __init pl010_console_setup(st
static struct uart_driver amba_reg;
static struct console amba_console = {
- .name = "ttyAM",
+ .name = SERIAL_AMBA_NAME,
.write = pl010_console_write,
.device = uart_console_device,
.setup = pl010_console_setup,
@@ -678,11 +677,11 @@ static struct console amba_console = {
static struct uart_driver amba_reg = {
.owner = THIS_MODULE,
- .driver_name = "ttyAM",
- .dev_name = "ttyAM",
+ .driver_name = SERIAL_AMBA_NAME,
+ .dev_name = SERIAL_AMBA_NAME,
.major = SERIAL_AMBA_MAJOR,
.minor = SERIAL_AMBA_MINOR,
- .nr = UART_NR,
+ .nr = SERIAL_AMBA_NR,
.cons = AMBA_CONSOLE,
};
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -16,10 +16,25 @@ config SERIAL_AMBA_PL010
help
This selects the ARM(R) AMBA(R) PrimeCell PL010 UART. If you have
an Integrator/AP or Integrator/PP2 platform, or if you have a
- Cirrus Logic EP93xx CPU, say Y or M here.
+ Cirrus Logic EP93xx CPU or an Infineon ADM5120 SOC, say Y or M here.
If unsure, say N.
+config SERIAL_AMBA_PL010_NUMPORTS
+ int "Maximum number of AMBA PL010 serial ports"
+ depends on SERIAL_AMBA_PL010
+ default "8"
+ ---help---
+ Set this to the number of serial ports you want the AMBA PL010 driver
+ to support.
+
+config SERIAL_AMBA_PL010_PORTNAME
+ string "Name of the AMBA PL010 serial ports"
+ depends on SERIAL_AMBA_PL010
+ default "ttyAM"
+ ---help---
+ ::: To be written :::
+
config SERIAL_AMBA_PL010_CONSOLE
bool "Support for console on AMBA serial port"
depends on SERIAL_AMBA_PL010=y

View File

@ -0,0 +1,13 @@
--- a/drivers/amba/bus.c
+++ b/drivers/amba/bus.c
@@ -20,6 +20,10 @@
#include <asm/irq.h>
#include <asm/sizes.h>
+#ifndef NO_IRQ
+#define NO_IRQ (-1)
+#endif
+
#define to_amba_driver(d) container_of(d, struct amba_driver, drv)
static const struct amba_id *

View File

@ -0,0 +1,27 @@
--- a/drivers/leds/leds-gpio.c
+++ b/drivers/leds/leds-gpio.c
@@ -55,13 +55,17 @@ static void gpio_led_set(struct led_clas
container_of(led_cdev, struct gpio_led_data, cdev);
int level;
- if (value == LED_OFF)
- level = 0;
- else
- level = 1;
-
- if (led_dat->active_low)
- level = !level;
+ switch (value) {
+ case LED_OFF:
+ level = led_dat->active_low ? 1 : 0;
+ break;
+ case LED_FULL:
+ level = led_dat->active_low ? 0 : 1;
+ break;
+ default:
+ level = value;
+ break;
+ }
/* Setting GPIOs with I2C/etc requires a task context, and we don't
* seem to have a reliable way to know if we're already in one; so

View File

@ -0,0 +1,31 @@
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -943,6 +943,18 @@ config RC32434_WDT
To compile this driver as a module, choose M here: the
module will be called rc32434_wdt.
+config ADM5120_WDT
+ tristate "Infineon ADM5120 SoC hardware watchdog"
+ depends on WATCHDOG && ADM5120
+ help
+ This is a driver for hardware watchdog integrated in Infineon
+ ADM5120 SoC. This watchdog simply watches your kernel to make sure
+ it doesn't freeze, and if it does, it reboots your computer after a
+ certain amount of time.
+
+ To compile this driver as a module, choose M here: the module will be
+ called adm5120_wdt.
+
config INDYDOG
tristate "Indy/I2 Hardware Watchdog"
depends on SGI_HAS_INDYDOG
--- a/drivers/watchdog/Makefile
+++ b/drivers/watchdog/Makefile
@@ -122,6 +122,7 @@ obj-$(CONFIG_ATH79_WDT) += ath79_wdt.o
obj-$(CONFIG_BCM47XX_WDT) += bcm47xx_wdt.o
obj-$(CONFIG_BCM63XX_WDT) += bcm63xx_wdt.o
obj-$(CONFIG_RC32434_WDT) += rc32434_wdt.o
+obj-$(CONFIG_ADM5120_WDT) += adm5120_wdt.o
obj-$(CONFIG_INDYDOG) += indydog.o
obj-$(CONFIG_JZ4740_WDT) += jz4740_wdt.o
obj-$(CONFIG_WDT_MTX1) += mtx-1_wdt.o

View File

@ -0,0 +1,22 @@
--- /dev/null
+++ b/arch/mips/adm5120/Platform
@@ -0,0 +1,19 @@
+#
+# Infineon/ADMtek ADM5120
+#
+
+platform-$(CONFIG_ADM5120) += adm5120/common/
+
+platform-$(CONFIG_ADM5120_OEM_CELLVISION) += adm5120/cellvision/
+platform-$(CONFIG_ADM5120_OEM_COMPEX) += adm5120/compex/
+platform-$(CONFIG_ADM5120_OEM_EDIMAX) += adm5120/edimax/
+platform-$(CONFIG_ADM5120_OEM_GENERIC) += adm5120/generic/
+platform-$(CONFIG_ADM5120_OEM_INFINEON) += adm5120/infineon/
+platform-$(CONFIG_ADM5120_OEM_MIKROTIK) += adm5120/mikrotik/
+platform-$(CONFIG_ADM5120_OEM_MOTOROLA) += adm5120/motorola/
+platform-$(CONFIG_ADM5120_OEM_OSBRIDGE) += adm5120/osbridge/
+platform-$(CONFIG_ADM5120_OEM_ZYXEL) += adm5120/zyxel/
+
+cflags-$(CONFIG_ADM5120) += -I$(srctree)/arch/mips/include/asm/mach-adm5120
+libs-$(CONFIG_ADM5120) += arch/mips/adm5120/prom/
+load-$(CONFIG_ADM5120) += 0xffffffff80001000

View File

@ -0,0 +1,110 @@
--- a/arch/mips/adm5120/common/platform.c
+++ b/arch/mips/adm5120/common/platform.c
@@ -18,6 +18,7 @@
#include <linux/gpio.h>
#include <linux/irq.h>
#include <linux/slab.h>
+#include <linux/export.h>
#include <asm/bootinfo.h>
--- a/arch/mips/adm5120/common/clock.c
+++ b/arch/mips/adm5120/common/clock.c
@@ -33,7 +33,7 @@ static struct clk uart_clk = {
struct clk *clk_get(struct device *dev, const char *id)
{
- char *name = dev_name(dev);
+ const char *name = dev_name(dev);
if (!strcmp(name, "apb:uart0") || !strcmp(name, "apb:uart1"))
return &uart_clk;
--- a/arch/mips/pci/pci-adm5120.c
+++ b/arch/mips/pci/pci-adm5120.c
@@ -49,7 +49,7 @@
static unsigned int adm5120_pci_nr_irqs __initdata;
static struct adm5120_pci_irq *adm5120_pci_irq_map __initdata;
-static spinlock_t pci_lock = SPIN_LOCK_UNLOCKED;
+static DEFINE_SPINLOCK(pci_lock);
/* -------------------------------------------------------------------------*/
--- a/arch/mips/adm5120/common/irq.c
+++ b/arch/mips/adm5120/common/irq.c
@@ -23,9 +23,9 @@
#include <asm/mach-adm5120/adm5120_defs.h>
-static void adm5120_intc_irq_unmask(unsigned int irq);
-static void adm5120_intc_irq_mask(unsigned int irq);
-static int adm5120_intc_irq_set_type(unsigned int irq, unsigned int flow_type);
+static void adm5120_intc_irq_unmask(struct irq_data *d);
+static void adm5120_intc_irq_mask(struct irq_data *d);
+static int adm5120_intc_irq_set_type(struct irq_data *d, unsigned int flow_type);
static inline void intc_write_reg(unsigned int reg, u32 val)
{
@@ -43,10 +43,10 @@ static inline u32 intc_read_reg(unsigned
static struct irq_chip adm5120_intc_irq_chip = {
.name = "INTC",
- .unmask = adm5120_intc_irq_unmask,
- .mask = adm5120_intc_irq_mask,
- .mask_ack = adm5120_intc_irq_mask,
- .set_type = adm5120_intc_irq_set_type
+ .irq_unmask = adm5120_intc_irq_unmask,
+ .irq_mask = adm5120_intc_irq_mask,
+ .irq_mask_ack = adm5120_intc_irq_mask,
+ .irq_set_type = adm5120_intc_irq_set_type
};
static struct irqaction adm5120_intc_irq_action = {
@@ -54,20 +54,19 @@ static struct irqaction adm5120_intc_irq
.name = "cascade [INTC]"
};
-static void adm5120_intc_irq_unmask(unsigned int irq)
+static void adm5120_intc_irq_unmask(struct irq_data *d)
{
- irq -= ADM5120_INTC_IRQ_BASE;
- intc_write_reg(INTC_REG_IRQ_ENABLE, 1 << irq);
+ intc_write_reg(INTC_REG_IRQ_ENABLE, 1 << (d->irq - ADM5120_INTC_IRQ_BASE));
}
-static void adm5120_intc_irq_mask(unsigned int irq)
+static void adm5120_intc_irq_mask(struct irq_data *d)
{
- irq -= ADM5120_INTC_IRQ_BASE;
- intc_write_reg(INTC_REG_IRQ_DISABLE, 1 << irq);
+ intc_write_reg(INTC_REG_IRQ_DISABLE, 1 << (d->irq - ADM5120_INTC_IRQ_BASE));
}
-static int adm5120_intc_irq_set_type(unsigned int irq, unsigned int flow_type)
+static int adm5120_intc_irq_set_type(struct irq_data *d, unsigned int flow_type)
{
+ unsigned int irq = d->irq;
unsigned int sense;
unsigned long mode;
int err = 0;
@@ -105,10 +104,6 @@ static int adm5120_intc_irq_set_type(uns
mode &= ~(1 << (irq - ADM5120_INTC_IRQ_BASE));
intc_write_reg(INTC_REG_INT_MODE, mode);
- /* fallthrough */
- default:
- irq_desc[irq].status &= ~IRQ_TYPE_SENSE_MASK;
- irq_desc[irq].status |= sense;
break;
}
@@ -162,8 +157,7 @@ static void __init adm5120_intc_irq_init
for (i = ADM5120_INTC_IRQ_BASE;
i <= ADM5120_INTC_IRQ_BASE + INTC_IRQ_LAST;
i++) {
- irq_desc[i].status = INTC_IRQ_STATUS;
- set_irq_chip_and_handler(i, &adm5120_intc_irq_chip,
+ irq_set_chip_and_handler(i, &adm5120_intc_irq_chip,
handle_level_irq);
}

View File

@ -0,0 +1,306 @@
--- a/arch/mips/include/asm/mach-adm5120/adm5120_platform.h
+++ b/arch/mips/include/asm/mach-adm5120/adm5120_platform.h
@@ -28,10 +28,8 @@ struct adm5120_flash_platform_data {
void (*set_vpp)(struct map_info *, int);
void (*switch_bank)(unsigned);
u32 window_size;
-#ifdef CONFIG_MTD_PARTITIONS
unsigned int nr_parts;
struct mtd_partition *parts;
-#endif
};
struct adm5120_switch_platform_data {
--- a/arch/mips/adm5120/infineon/infineon.c
+++ b/arch/mips/adm5120/infineon/infineon.c
@@ -16,7 +16,6 @@
#define EASY_CONFIG_OFFSET 0x10000
#define EASY_CONFIG_SIZE 0x1000
-#ifdef CONFIG_MTD_PARTITIONS
static struct mtd_partition easy_partitions[] = {
{
.name = "admboot",
@@ -33,7 +32,6 @@ static struct mtd_partition easy_partiti
.size = MTDPART_SIZ_FULL,
}
};
-#endif /* CONFIG_MTD_PARTITIONS */
static __init void easy_setup_mac(void)
{
@@ -68,10 +66,8 @@ void __init easy_setup_pqfp(void)
gpio_direction_output(ADM5120_GPIO_PIN3, 0);
adm5120_flash0_data.switch_bank = switch_bank_gpio3;
-#ifdef CONFIG_MTD_PARTITIONS
adm5120_flash0_data.nr_parts = ARRAY_SIZE(easy_partitions);
adm5120_flash0_data.parts = easy_partitions;
-#endif /* CONFIG_MTD_PARTITIONS */
adm5120_add_device_uart(0);
adm5120_add_device_uart(1);
@@ -100,10 +96,8 @@ void __init easy_setup_bga(void)
gpio_direction_output(ADM5120_GPIO_PIN5, 0);
adm5120_flash0_data.switch_bank = switch_bank_gpio5;
-#ifdef CONFIG_MTD_PARTITIONS
adm5120_flash0_data.nr_parts = ARRAY_SIZE(easy_partitions);
adm5120_flash0_data.parts = easy_partitions;
-#endif /* CONFIG_MTD_PARTITIONS */
adm5120_add_device_uart(0);
adm5120_add_device_uart(1);
--- a/arch/mips/adm5120/cellvision/cellvision.c
+++ b/arch/mips/adm5120/cellvision/cellvision.c
@@ -19,7 +19,6 @@
#define CELLVISION_CONFIG_OFFSET 0x8000
#define CELLVISION_CONFIG_SIZE 0x1000
-#ifdef CONFIG_MTD_PARTITIONS
static struct mtd_partition cas6xx_partitions[] = {
{
.name = "admboot",
@@ -65,7 +64,6 @@ static struct mtd_partition cas7xx_parti
.size = MTDPART_SIZ_FULL,
}
};
-#endif /* CONFIG_MTD_PARTITIONS */
static void switch_bank_gpio5(unsigned bank)
{
@@ -105,20 +103,16 @@ void __init cellvision_mac_setup(void)
void __init cas6xx_flash_setup(void)
{
-#ifdef CONFIG_MTD_PARTITIONS
adm5120_flash0_data.nr_parts = ARRAY_SIZE(cas6xx_partitions);
adm5120_flash0_data.parts = cas6xx_partitions;
-#endif /* CONFIG_MTD_PARTITIONS */
cellvision_flash_setup();
}
void __init cas7xx_flash_setup(void)
{
-#ifdef CONFIG_MTD_PARTITIONS
adm5120_flash0_data.nr_parts = ARRAY_SIZE(cas7xx_partitions);
adm5120_flash0_data.parts = cas7xx_partitions;
-#endif /* CONFIG_MTD_PARTITIONS */
cellvision_flash_setup();
}
--- a/arch/mips/adm5120/edimax/br-61xx.c
+++ b/arch/mips/adm5120/edimax/br-61xx.c
@@ -18,7 +18,6 @@
#define BR61XX_CONFIG_OFFSET 0x8000
#define BR61XX_CONFIG_SIZE 0x1000
-#ifdef CONFIG_MTD_PARTITIONS
static struct mtd_partition br61xx_partitions[] = {
{
.name = "admboot",
@@ -35,7 +34,6 @@ static struct mtd_partition br61xx_parti
.size = MTDPART_SIZ_FULL,
}
};
-#endif /* CONFIG_MTD_PARTITIONS */
static struct gpio_button br61xx_gpio_buttons[] __initdata = {
{
@@ -68,10 +66,8 @@ static void __init br61xx_mac_setup(void
void __init br61xx_generic_setup(void)
{
-#ifdef CONFIG_MTD_PARTITIONS
adm5120_flash0_data.nr_parts = ARRAY_SIZE(br61xx_partitions);
adm5120_flash0_data.parts = br61xx_partitions;
-#endif /* CONFIG_MTD_PARTITIONS */
adm5120_add_device_flash(0);
adm5120_add_device_gpio(BR61XX_GPIO_DEV_MASK);
--- a/arch/mips/adm5120/mikrotik/rb-1xx.c
+++ b/arch/mips/adm5120/mikrotik/rb-1xx.c
@@ -25,7 +25,6 @@ static struct adm5120_pci_irq rb1xx_pci_
PCIIRQ(3, 0, 1, ADM5120_IRQ_PCI2)
};
-#ifdef CONFIG_MTD_PARTITIONS
static struct mtd_partition rb1xx_nor_parts[] = {
{
.name = "booter",
@@ -50,7 +49,6 @@ static struct mtd_partition rb1xx_nand_p
.size = MTDPART_SIZ_FULL
}
};
-#endif /* CONFIG_MTD_PARTITIONS */
/*
* We need to use the OLD Yaffs-1 OOB layout, otherwise the RB bootloader
@@ -79,10 +77,8 @@ static int rb1xx_nand_fixup(struct mtd_i
struct platform_nand_data rb1xx_nand_data __initdata = {
.chip = {
.nr_chips = 1,
-#ifdef CONFIG_MTD_PARTITIONS
.nr_partitions = ARRAY_SIZE(rb1xx_nand_parts),
.partitions = rb1xx_nand_parts,
-#endif /* CONFIG_MTD_PARTITIONS */
.chip_delay = RB1XX_NAND_CHIP_DELAY,
.options = NAND_NO_AUTOINCR,
.chip_fixup = rb1xx_nand_fixup,
@@ -114,10 +110,8 @@ static void __init rb1xx_mac_setup(void)
void __init rb1xx_add_device_flash(void)
{
/* setup data for flash0 device */
-#ifdef CONFIG_MTD_PARTITIONS
adm5120_flash0_data.nr_parts = ARRAY_SIZE(rb1xx_nor_parts);
adm5120_flash0_data.parts = rb1xx_nor_parts;
-#endif /* CONFIG_MTD_PARTITIONS */
adm5120_flash0_data.window_size = 128*1024;
adm5120_add_device_flash(0);
--- a/arch/mips/adm5120/compex/wp54.c
+++ b/arch/mips/adm5120/compex/wp54.c
@@ -11,7 +11,6 @@
#include "compex.h"
-#ifdef CONFIG_MTD_PARTITIONS
static struct mtd_partition wp54g_wrt_partitions[] = {
{
.name = "cfe",
@@ -28,7 +27,6 @@ static struct mtd_partition wp54g_wrt_pa
.size = 0x010000,
}
};
-#endif /* CONFIG_MTD_PARTITIONS */
static struct adm5120_pci_irq wp54_pci_irqs[] __initdata = {
PCIIRQ(2, 0, 1, ADM5120_IRQ_PCI0),
@@ -83,10 +81,8 @@ MIPS_MACHINE(MACH_ADM5120_WP54, "WP54",
static void __init wp54_wrt_setup(void)
{
-#ifdef CONFIG_MTD_PARTITIONS
adm5120_flash0_data.nr_parts = ARRAY_SIZE(wp54g_wrt_partitions);
adm5120_flash0_data.parts = wp54g_wrt_partitions;
-#endif
wp54_setup();
}
--- a/arch/mips/adm5120/zyxel/p-33x.c
+++ b/arch/mips/adm5120/zyxel/p-33x.c
@@ -16,7 +16,6 @@
#define P33X_GPIO_FLASH_A20 ADM5120_GPIO_PIN5
#define P33X_GPIO_DEV_MASK (1 << P33X_GPIO_FLASH_A20)
-#ifdef CONFIG_MTD_PARTITIONS
static struct mtd_partition p33x_partitions[] = {
{
.name = "bootbase",
@@ -46,7 +45,6 @@ static struct mtd_partition p33x_partiti
.size = MTDPART_SIZ_FULL,
}
};
-#endif /* CONFIG_MTD_PARTITIONS */
static struct adm5120_pci_irq p33x_pci_irqs[] __initdata = {
PCIIRQ(2, 0, 1, ADM5120_IRQ_PCI0),
@@ -75,10 +73,8 @@ void __init p33x_generic_setup(void)
gpio_request(P33X_GPIO_FLASH_A20, NULL); /* for flash A20 line */
gpio_direction_output(P33X_GPIO_FLASH_A20, 0);
adm5120_flash0_data.switch_bank = switch_bank_gpio5;
-#ifdef CONFIG_MTD_PARTITIONS
adm5120_flash0_data.nr_parts = ARRAY_SIZE(p33x_partitions);
adm5120_flash0_data.parts = p33x_partitions;
-#endif /* CONFIG_MTD_PARTITIONS */
adm5120_add_device_flash(0);
adm5120_add_device_uart(0);
--- a/arch/mips/adm5120/generic/eb-214a.c
+++ b/arch/mips/adm5120/generic/eb-214a.c
@@ -28,7 +28,6 @@
#define EB214A_GPIO_DEV_MASK 0
#define EB214A_CONFIG_OFFSET 0x4000
-#ifdef CONFIG_MTD_PARTITIONS
static struct mtd_partition eb214a_partitions[] = {
{
.name = "bootloader",
@@ -45,7 +44,6 @@ static struct mtd_partition eb214a_parti
.size = MTDPART_SIZ_FULL,
}
};
-#endif /* CONFIG_MTD_PARTITIONS */
static struct adm5120_pci_irq eb214a_pci_irqs[] __initdata = {
PCIIRQ(4, 0, 1, ADM5120_IRQ_PCI0),
@@ -94,10 +92,8 @@ static void __init eb214a_mac_setup(void
static void __init eb214a_setup(void)
{
-#ifdef CONFIG_MTD_PARTITIONS
adm5120_flash0_data.nr_parts = ARRAY_SIZE(eb214a_partitions);
adm5120_flash0_data.parts = eb214a_partitions;
-#endif /* CONFIG_MTD_PARTITIONS */
adm5120_add_device_flash(0);
adm5120_add_device_gpio(EB214A_GPIO_DEV_MASK);
--- a/arch/mips/adm5120/motorola/pmugw.c
+++ b/arch/mips/adm5120/motorola/pmugw.c
@@ -26,7 +26,6 @@
#define PMUGW_CONFIG_OFFSET 0x10000
#define PMUGW_CONFIG_SIZE 0x1000
-#ifdef CONFIG_MTD_PARTITIONS
static struct mtd_partition pmugw_partitions[] = {
{
.name = "admboot",
@@ -43,7 +42,6 @@ static struct mtd_partition pmugw_partit
.size = MTDPART_SIZ_FULL,
}
};
-#endif /* CONFIG_MTD_PARTITIONS */
static u8 pmugw_vlans[6] __initdata = {
0x41, 0x42, 0x44, 0x48, 0x50, 0x00
@@ -82,10 +80,8 @@ void __init pmugw_setup(void)
gpio_direction_output(ADM5120_GPIO_PIN5, 0);
adm5120_flash0_data.switch_bank = switch_bank_gpio5;
-#ifdef CONFIG_MTD_PARTITIONS
adm5120_flash0_data.nr_parts = ARRAY_SIZE(pmugw_partitions);
adm5120_flash0_data.parts = pmugw_partitions;
-#endif /* CONFIG_MTD_PARTITIONS */
adm5120_add_device_uart(1); /* ttyS0 */
adm5120_add_device_uart(0); /* ttyS1 */
--- a/arch/mips/adm5120/osbridge/5gxi.c
+++ b/arch/mips/adm5120/osbridge/5gxi.c
@@ -20,7 +20,6 @@
#include <asm/mach-adm5120/adm5120_platform.h>
#include <asm/mach-adm5120/adm5120_info.h>
-#ifdef CONFIG_MTD_PARTITIONS
static struct mtd_partition osbridge_5gxi_partitions[] = {
{
.name = "bootloader",
@@ -37,7 +36,6 @@ static struct mtd_partition osbridge_5gx
.size = MTDPART_SIZ_FULL,
}
};
-#endif /* CONFIG_MTD_PARTITIONS */
static struct gpio_led osbridge_5gxi_gpio_leds[] __initdata = {
GPIO_LED_INV(ADM5120_GPIO_PIN6, "5gxi:green:user", NULL),
@@ -54,10 +52,8 @@ static u8 osbridge_5gxi_vlans[6] __initd
static void __init osbridge_5gxi_setup(void)
{
-#ifdef CONFIG_MTD_PARTITIONS
adm5120_flash0_data.nr_parts = ARRAY_SIZE(osbridge_5gxi_partitions);
adm5120_flash0_data.parts = osbridge_5gxi_partitions;
-#endif /* CONFIG_MTD_PARTITIONS */
adm5120_add_device_uart(0);
adm5120_add_device_uart(1);

View File

@ -0,0 +1,263 @@
--- a/arch/mips/adm5120/common/platform.c
+++ b/arch/mips/adm5120/common/platform.c
@@ -245,31 +245,44 @@ void __init adm5120_add_device_uart(unsi
/*
* GPIO buttons
*/
-#define ADM5120_BUTTON_INTERVAL 20
-struct gpio_buttons_platform_data adm5120_gpio_buttons_data = {
- .poll_interval = ADM5120_BUTTON_INTERVAL,
-};
-
-struct platform_device adm5120_gpio_buttons_device = {
- .name = "gpio-buttons",
- .id = -1,
- .dev.platform_data = &adm5120_gpio_buttons_data,
-};
-
-void __init adm5120_add_device_gpio_buttons(unsigned nbuttons,
- struct gpio_button *buttons)
+void __init adm5120_register_gpio_buttons(int id,
+ unsigned poll_interval,
+ unsigned nbuttons,
+ struct gpio_keys_button *buttons)
{
- struct gpio_button *p;
+ struct platform_device *pdev;
+ struct gpio_keys_platform_data pdata;
+ struct gpio_keys_button *p;
+ int err;
- p = kmalloc(nbuttons * sizeof(*p), GFP_KERNEL);
+ p = kmemdup(buttons, nbuttons * sizeof(*p), GFP_KERNEL);
if (!p)
return;
- memcpy(p, buttons, nbuttons * sizeof(*p));
- adm5120_gpio_buttons_data.nbuttons = nbuttons;
- adm5120_gpio_buttons_data.buttons = p;
+ pdev = platform_device_alloc("gpio-keys-polled", id);
+ if (!pdev)
+ goto err_free_buttons;
+
+ memset(&pdata, 0, sizeof(pdata));
+ pdata.poll_interval = poll_interval;
+ pdata.nbuttons = nbuttons;
+ pdata.buttons = p;
+
+ err = platform_device_add_data(pdev, &pdata, sizeof(pdata));
+ if (err)
+ goto err_put_pdev;
+
+ err = platform_device_add(pdev);
+ if (err)
+ goto err_put_pdev;
+
+ return;
+
+err_put_pdev:
+ platform_device_put(pdev);
- platform_device_register(&adm5120_gpio_buttons_device);
+err_free_buttons:
+ kfree(p);
}
/*
--- a/arch/mips/include/asm/mach-adm5120/adm5120_platform.h
+++ b/arch/mips/include/asm/mach-adm5120/adm5120_platform.h
@@ -20,7 +20,8 @@
#include <linux/mtd/map.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/nand.h>
-#include <linux/gpio_buttons.h>
+#include <linux/input.h>
+#include <linux/gpio_keys.h>
#include <linux/amba/bus.h>
#include <linux/amba/serial.h>
@@ -66,8 +67,10 @@ extern void adm5120_add_device_uart(unsi
extern void adm5120_add_device_nand(struct platform_nand_data *pdata) __init;
extern void adm5120_add_device_switch(unsigned num_ports, u8 *vlan_map) __init;
extern void adm5120_add_device_gpio(u32 disable_mask) __init;
-extern void adm5120_add_device_gpio_buttons(unsigned nbuttons,
- struct gpio_button *buttons) __init;
+extern void adm5120_register_gpio_buttons(int id,
+ unsigned poll_interval,
+ unsigned nbuttons,
+ struct gpio_keys_button *buttons);
#define GPIO_LED_DEF(g, n, t, a) { \
.name = (n), \
--- a/arch/mips/adm5120/compex/wp54.c
+++ b/arch/mips/adm5120/compex/wp54.c
@@ -11,6 +11,9 @@
#include "compex.h"
+#define WP54_KEYS_POLL_INTERVAL 20
+#define WP54_KEYS_DEBOUNCE_INTERVAL (3 * WP54_KEYS_POLL_INTERVAL)
+
static struct mtd_partition wp54g_wrt_partitions[] = {
{
.name = "cfe",
@@ -32,12 +35,12 @@ static struct adm5120_pci_irq wp54_pci_i
PCIIRQ(2, 0, 1, ADM5120_IRQ_PCI0),
};
-static struct gpio_button wp54_gpio_buttons[] __initdata = {
+static struct gpio_keys_button wp54_gpio_buttons[] __initdata = {
{
.desc = "reset_button",
.type = EV_KEY,
- .code = BTN_0,
- .threshold = 5,
+ .code = KEY_RESTART,
+ .debounce_interval = WP54_KEYS_DEBOUNCE_INTERVAL,
.gpio = ADM5120_GPIO_PIN4,
}
};
@@ -69,8 +72,9 @@ static void __init wp54_setup(void)
adm5120_board_reset = wp54_reset;
adm5120_add_device_switch(2, wp54_vlans);
- adm5120_add_device_gpio_buttons(ARRAY_SIZE(wp54_gpio_buttons),
- wp54_gpio_buttons);
+ adm5120_register_gpio_buttons(-1, WP54_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(wp54_gpio_buttons),
+ wp54_gpio_buttons);
adm5120_add_device_gpio_leds(ARRAY_SIZE(wp54_gpio_leds),
wp54_gpio_leds);
--- a/arch/mips/adm5120/mikrotik/rb-1xx.c
+++ b/arch/mips/adm5120/mikrotik/rb-1xx.c
@@ -19,6 +19,9 @@
#define RB1XX_NAND_CHIP_DELAY 25
+#define RB1XX_KEYS_POLL_INTERVAL 20
+#define RB1XX_KEYS_DEBOUNCE_INTERVAL (3 * RB1XX_KEYS_POLL_INTERVAL)
+
static struct adm5120_pci_irq rb1xx_pci_irqs[] __initdata = {
PCIIRQ(1, 0, 1, ADM5120_IRQ_PCI0),
PCIIRQ(2, 0, 1, ADM5120_IRQ_PCI1),
@@ -85,12 +88,12 @@ struct platform_nand_data rb1xx_nand_dat
},
};
-struct gpio_button rb1xx_gpio_buttons[] __initdata = {
+struct gpio_keys_button rb1xx_gpio_buttons[] __initdata = {
{
.desc = "reset_button",
.type = EV_KEY,
- .code = BTN_0,
- .threshold = 5,
+ .code = KEY_RESTART,
+ .debounce_interval = RB1XX_KEYS_DEBOUNCE_INTERVAL,
.gpio = ADM5120_GPIO_PIN7,
}
};
@@ -138,8 +141,9 @@ void __init rb1xx_generic_setup(void)
adm5120_add_device_uart(0);
adm5120_add_device_uart(1);
- adm5120_add_device_gpio_buttons(ARRAY_SIZE(rb1xx_gpio_buttons),
- rb1xx_gpio_buttons);
+ adm5120_register_gpio_buttons(-1, RB1XX_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(rb1xx_gpio_buttons),
+ rb1xx_gpio_buttons);
rb1xx_add_device_flash();
rb1xx_mac_setup();
--- a/arch/mips/adm5120/generic/eb-214a.c
+++ b/arch/mips/adm5120/generic/eb-214a.c
@@ -28,6 +28,9 @@
#define EB214A_GPIO_DEV_MASK 0
#define EB214A_CONFIG_OFFSET 0x4000
+#define EB214A_KEYS_POLL_INTERVAL 20
+#define EB214A_KEYS_DEBOUNCE_INTERVAL (3 * EB214A_KEYS_POLL_INTERVAL)
+
static struct mtd_partition eb214a_partitions[] = {
{
.name = "bootloader",
@@ -60,12 +63,12 @@ static struct gpio_led eb214a_gpio_leds[
GPIO_LED_INV(ADM5120_GPIO_P3L0, "usb4", NULL),
};
-static struct gpio_button eb214a_gpio_buttons[] __initdata = {
+static struct gpio_keys_button eb214a_gpio_buttons[] __initdata = {
{
.desc = "reset",
.type = EV_KEY,
- .code = BTN_0,
- .threshold = 5,
+ .code = KEY_RESTART,
+ .debounce_interval = EB214A_KEYS_DEBOUNCE_INTERVAL,
.gpio = ADM5120_GPIO_PIN1,
}
};
@@ -105,8 +108,9 @@ static void __init eb214a_setup(void)
eb214a_mac_setup();
- adm5120_add_device_gpio_buttons(ARRAY_SIZE(eb214a_gpio_buttons),
- eb214a_gpio_buttons);
+ adm5120_register_gpio_buttons(-1, EB214A_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(eb214a_gpio_buttons),
+ eb214a_gpio_buttons);
adm5120_add_device_gpio_leds(ARRAY_SIZE(eb214a_gpio_leds),
eb214a_gpio_leds);
--- a/arch/mips/adm5120/edimax/br-61xx.c
+++ b/arch/mips/adm5120/edimax/br-61xx.c
@@ -18,6 +18,9 @@
#define BR61XX_CONFIG_OFFSET 0x8000
#define BR61XX_CONFIG_SIZE 0x1000
+#define BR61XX_KEYS_POLL_INTERVAL 20
+#define BR61XX_KEYS_DEBOUNCE_INTERVAL (3 * BR61XX_KEYS_POLL_INTERVAL)
+
static struct mtd_partition br61xx_partitions[] = {
{
.name = "admboot",
@@ -35,12 +38,12 @@ static struct mtd_partition br61xx_parti
}
};
-static struct gpio_button br61xx_gpio_buttons[] __initdata = {
+static struct gpio_keys_button br61xx_gpio_buttons[] __initdata = {
{
.desc = "reset_button",
.type = EV_KEY,
- .code = BTN_0,
- .threshold = 5,
+ .code = KEY_RESTART,
+ .debounce_interval = BR61XX_KEYS_DEBOUNCE_INTERVAL,
.gpio = ADM5120_GPIO_PIN2,
}
};
@@ -76,8 +79,10 @@ void __init br61xx_generic_setup(void)
adm5120_add_device_uart(1);
adm5120_add_device_switch(5, br61xx_vlans);
- adm5120_add_device_gpio_buttons(ARRAY_SIZE(br61xx_gpio_buttons),
- br61xx_gpio_buttons);
+
+ adm5120_register_gpio_buttons(-1, BR61XX_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(br61xx_gpio_buttons),
+ br61xx_gpio_buttons);
br61xx_mac_setup();
}
--- a/arch/mips/adm5120/mikrotik/rb-1xx.h
+++ b/arch/mips/adm5120/mikrotik/rb-1xx.h
@@ -26,7 +26,7 @@
#include <prom/routerboot.h>
extern struct platform_nand_data rb1xx_nand_data __initdata;
-extern struct gpio_button rb1xx_gpio_buttons[] __initdata;
+extern struct gpio_keys_button rb1xx_gpio_buttons[] __initdata;
extern void rb1xx_add_device_flash(void) __init;
extern void rb1xx_add_device_nand(void) __init;

View File

@ -0,0 +1,33 @@
--- a/drivers/ata/pata_rb153_cf.c
+++ b/drivers/ata/pata_rb153_cf.c
@@ -56,7 +56,7 @@ static inline void rb153_pata_finish_io(
ata_sff_dma_pause(ap);
ndelay(RB153_CF_IO_DELAY);
- set_irq_type(info->irq, IRQ_TYPE_LEVEL_HIGH);
+ irq_set_irq_type(info->irq, IRQ_TYPE_LEVEL_HIGH);
}
static void rb153_pata_exec_command(struct ata_port *ap,
@@ -107,11 +107,11 @@ static irqreturn_t rb153_pata_irq_handle
struct rb153_cf_info *info = ah->private_data;
if (gpio_get_value(info->gpio_line)) {
- set_irq_type(info->irq, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(info->irq, IRQ_TYPE_LEVEL_LOW);
if (!info->frozen)
ata_sff_interrupt(irq, dev_instance);
} else {
- set_irq_type(info->irq, IRQ_TYPE_LEVEL_HIGH);
+ irq_set_irq_type(info->irq, IRQ_TYPE_LEVEL_HIGH);
}
return IRQ_HANDLED;
@@ -138,7 +138,6 @@ static void rb153_pata_setup_port(struct
ap->ops = &rb153_pata_port_ops;
ap->pio_mask = 0x1f; /* PIO4 */
- ap->flags = ATA_FLAG_NO_LEGACY | ATA_FLAG_MMIO;
ap->ioaddr.cmd_addr = info->iobase + RB153_CF_REG_CMD;
ap->ioaddr.ctl_addr = info->iobase + RB153_CF_REG_CTRL;

View File

@ -0,0 +1,21 @@
--- a/drivers/watchdog/adm5120_wdt.c
+++ b/drivers/watchdog/adm5120_wdt.c
@@ -123,8 +123,7 @@ static ssize_t wdt_write(struct file *fi
return 0;
}
-static int wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long wdt_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
{
int new_timeout;
static struct watchdog_info ident = {
@@ -166,7 +165,7 @@ static const struct file_operations wdt_
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = wdt_write,
- .ioctl = wdt_ioctl,
+ .unlocked_ioctl = wdt_ioctl,
.open = wdt_open,
.release = wdt_release,
};

View File

@ -0,0 +1,84 @@
--- a/drivers/net/adm5120sw.c
+++ b/drivers/net/adm5120sw.c
@@ -38,6 +38,7 @@
#include <asm/mach-adm5120/adm5120_switch.h>
#include "adm5120sw.h"
+#include <linux/dma-mapping.h>
#define DRV_NAME "adm5120-switch"
#define DRV_DESC "ADM5120 built-in ethernet switch driver"
@@ -153,7 +154,7 @@ static unsigned int cur_txl, dirty_txl;
static unsigned int sw_used;
-static spinlock_t tx_lock = SPIN_LOCK_UNLOCKED;
+static DEFINE_SPINLOCK(tx_lock);
/* ------------------------------------------------------------------------ */
@@ -216,6 +217,7 @@ static inline int desc_ipcsum_fail(struc
/* ------------------------------------------------------------------------ */
+#ifdef CONFIG_ADM5120_SWITCH_DEBUG
static void sw_dump_desc(char *label, struct dma_desc *desc, int tx)
{
u32 t;
@@ -336,6 +338,11 @@ static void sw_dump_regs(void)
t = sw_read_reg(SWITCH_REG_RLDA);
SW_DBG("rlda: %08X\n", t);
}
+#else
+static inline void sw_dump_desc(char *label, struct dma_desc *desc, int tx) {}
+static void sw_dump_intr_mask(char *label, u32 mask) {}
+static inline void sw_dump_regs(void) {}
+#endif /* CONFIG_ADM5120_SWITCH_DEBUG */
/* ------------------------------------------------------------------------ */
@@ -502,7 +509,7 @@ static int adm5120_if_poll(struct napi_s
{
struct adm5120_if_priv *priv = container_of(napi,
struct adm5120_if_priv, napi);
- struct net_device *dev = priv->dev;
+ struct net_device *dev __maybe_unused = priv->dev;
int done;
u32 status;
@@ -920,7 +927,7 @@ static void adm5120_if_tx_timeout(struct
SW_INFO("TX timeout on %s\n", dev->name);
}
-static void adm5120_if_set_multicast_list(struct net_device *dev)
+static void adm5120_if_set_rx_mode(struct net_device *dev)
{
struct adm5120_if_priv *priv = netdev_priv(dev);
u32 ports;
@@ -937,7 +944,7 @@ static void adm5120_if_set_multicast_lis
t |= (ports << CPUP_CONF_DUNP_SHIFT);
if (dev->flags & IFF_PROMISC || dev->flags & IFF_ALLMULTI ||
- dev->mc_count)
+ netdev_mc_count(dev))
/* enable multicast packets */
t &= ~(ports << CPUP_CONF_DMCP_SHIFT);
else
@@ -1024,7 +1031,7 @@ static const struct net_device_ops adm51
.ndo_open = adm5120_if_open,
.ndo_stop = adm5120_if_stop,
.ndo_start_xmit = adm5120_if_hard_start_xmit,
- .ndo_set_multicast_list = adm5120_if_set_multicast_list,
+ .ndo_set_rx_mode = adm5120_if_set_rx_mode,
.ndo_do_ioctl = adm5120_if_do_ioctl,
.ndo_tx_timeout = adm5120_if_tx_timeout,
.ndo_validate_addr = eth_validate_addr,
@@ -1076,7 +1083,7 @@ static void adm5120_switch_cleanup(void)
adm5120_switch_rx_ring_free();
}
-static int __init adm5120_switch_probe(struct platform_device *pdev)
+static int __devinit adm5120_switch_probe(struct platform_device *pdev)
{
u32 t;
int i, err;

View File

@ -0,0 +1,166 @@
--- a/drivers/mtd/maps/adm5120-flash.c
+++ b/drivers/mtd/maps/adm5120-flash.c
@@ -54,10 +54,6 @@ struct adm5120_flash_info {
struct resource *res;
struct platform_device *dev;
struct adm5120_map_info amap;
-#ifdef CONFIG_MTD_PARTITIONS
- int nr_parts;
- struct mtd_partition *parts[MAX_PARSED_PARTS];
-#endif
};
struct flash_desc {
@@ -96,7 +92,6 @@ static const char const *probe_types[] =
NULL
};
-#ifdef CONFIG_MTD_PARTITIONS
static const char const *parse_types[] = {
"cmdlinepart",
#ifdef CONFIG_MTD_REDBOOT_PARTS
@@ -106,7 +101,6 @@ static const char const *parse_types[] =
"MyLoader",
#endif
};
-#endif
#define BANK_SIZE (2<<20)
#define BANK_SIZE_MAX (4<<20)
@@ -318,89 +312,6 @@ static void adm5120_flash_initbanks(stru
info->mtd->size = info->amap.window_size;
}
-#ifdef CONFIG_MTD_PARTITIONS
-static int adm5120_flash_initparts(struct adm5120_flash_info *info)
-{
- struct adm5120_flash_platform_data *pdata;
- struct map_info *map = &info->amap.map;
- int num_parsers;
- const char *parser[2];
- int err = 0;
- int nr_parts;
- int i;
-
- info->nr_parts = 0;
-
- pdata = info->dev->dev.platform_data;
- if (pdata == NULL)
- goto out;
-
- if (pdata->nr_parts) {
- MAP_INFO(map, "adding static partitions\n");
- err = add_mtd_partitions(info->mtd, pdata->parts,
- pdata->nr_parts);
- if (err == 0) {
- info->nr_parts += pdata->nr_parts;
- goto out;
- }
- }
-
- num_parsers = ARRAY_SIZE(parse_types);
- if (num_parsers > MAX_PARSED_PARTS)
- num_parsers = MAX_PARSED_PARTS;
-
- parser[1] = NULL;
- for (i = 0; i < num_parsers; i++) {
- parser[0] = parse_types[i];
-
- MAP_INFO(map, "parsing \"%s\" partitions\n",
- parser[0]);
- nr_parts = parse_mtd_partitions(info->mtd, parser,
- &info->parts[i], 0);
-
- if (nr_parts <= 0)
- continue;
-
- MAP_INFO(map, "adding \"%s\" partitions\n",
- parser[0]);
-
- err = add_mtd_partitions(info->mtd, info->parts[i], nr_parts);
- if (err)
- break;
-
- info->nr_parts += nr_parts;
- }
-out:
- return err;
-}
-#else
-static int adm5120_flash_initparts(struct adm5120_flash_info *info)
-{
- return 0;
-}
-#endif /* CONFIG_MTD_PARTITIONS */
-
-#ifdef CONFIG_MTD_PARTITIONS
-static void adm5120_flash_remove_mtd(struct adm5120_flash_info *info)
-{
- int i;
-
- if (info->nr_parts) {
- del_mtd_partitions(info->mtd);
- for (i = 0; i < MAX_PARSED_PARTS; i++)
- if (info->parts[i] != NULL)
- kfree(info->parts[i]);
- } else {
- del_mtd_device(info->mtd);
- }
-}
-#else
-static void adm5120_flash_remove_mtd(struct adm5120_flash_info *info)
-{
- del_mtd_device(info->mtd);
-}
-#endif
-
static int adm5120_flash_remove(struct platform_device *dev)
{
struct adm5120_flash_info *info;
@@ -412,7 +323,7 @@ static int adm5120_flash_remove(struct p
platform_set_drvdata(dev, NULL);
if (info->mtd != NULL) {
- adm5120_flash_remove_mtd(info);
+ mtd_device_unregister(info->mtd);
map_destroy(info->mtd);
}
@@ -429,11 +340,18 @@ static int adm5120_flash_remove(struct p
static int adm5120_flash_probe(struct platform_device *dev)
{
+ struct adm5120_flash_platform_data *pdata;
struct adm5120_flash_info *info;
struct map_info *map;
const char **probe_type;
int err;
+ pdata = dev->dev.platform_data;
+ if (!pdata) {
+ dev_err(&dev->dev, "no platform data\n");
+ return -EINVAL;
+ }
+
info = kzalloc(sizeof(*info), GFP_KERNEL);
if (info == NULL) {
err = -ENOMEM;
@@ -484,16 +402,11 @@ static int adm5120_flash_probe(struct pl
info->mtd->owner = THIS_MODULE;
- err = adm5120_flash_initparts(info);
+ err = mtd_device_parse_register(info->mtd, parse_types, 0,
+ pdata->parts, pdata->nr_parts);
if (err)
goto err_out;
- if (info->nr_parts == 0) {
- MAP_INFO(map, "no partitions available, registering "
- "whole flash\n");
- add_mtd_device(info->mtd);
- }
-
return 0;
err_out:

View File

@ -0,0 +1,20 @@
--- a/drivers/mtd/trxsplit.c
+++ b/drivers/mtd/trxsplit.c
@@ -144,7 +144,7 @@ static void trxsplit_create_partitions(s
part = &trx_parts[i];
part->name = "rootfs";
- err = add_mtd_partitions(mtd, trx_parts, trx_nr_parts);
+ err = mtd_device_register(mtd, trx_parts, trx_nr_parts);
if (err) {
printk(KERN_ALERT PFX "adding TRX partitions failed\n");
return;
@@ -159,7 +159,7 @@ static int trxsplit_refresh_partitions(s
mtd->name, MTD_BLOCK_MAJOR, mtd->index);
/* remove old partitions */
- del_mtd_partitions(mtd);
+ mtd_device_unregister(mtd);
trxsplit_findtrx(mtd);
if (!trx_mtd)

View File

@ -0,0 +1,582 @@
--- a/drivers/usb/host/adm5120.h
+++ b/drivers/usb/host/adm5120.h
@@ -403,6 +403,7 @@ struct admhcd {
* other external transceivers should be software-transparent
*/
struct otg_transceiver *transceiver;
+ void (*start_hnp)(struct admhcd *ahcd);
#endif
/*
@@ -537,15 +538,7 @@ static inline struct usb_hcd *admhcd_to_
* Big-endian read/write functions are arch-specific.
* Other arches can be added if/when they're needed.
*
- * REVISIT: arch/powerpc now has readl/writel_be, so the
- * definition below can die once the STB04xxx support is
- * finally ported over.
*/
-#if defined(CONFIG_PPC) && !defined(CONFIG_PPC_MERGE)
-#define readl_be(addr) in_be32((__force unsigned *)addr)
-#define writel_be(val, addr) out_be32((__force unsigned *)addr, val)
-#endif
-
static inline unsigned int admhc_readl(const struct admhcd *ahcd,
__hc32 __iomem *regs)
{
--- a/drivers/usb/host/adm5120-drv.c
+++ b/drivers/usb/host/adm5120-drv.c
@@ -9,7 +9,7 @@
* (C) Copyright 2002 Hewlett-Packard Company
*
* Written by Christopher Hoover <ch@hpl.hp.com>
- * Based on fragments of previous driver by Rusell King et al.
+ * Based on fragments of previous driver by Russell King et al.
*
* Modified for LH7A404 from ahcd-sa1111.c
* by Durgesh Pattamatta <pattamattad@sharpsec.com>
@@ -81,7 +81,7 @@ static int admhc_adm5120_probe(const str
admhc_hcd_init(hcd_to_admhcd(hcd));
- retval = usb_add_hcd(hcd, irq, IRQF_DISABLED);
+ retval = usb_add_hcd(hcd, irq, 0);
if (retval)
goto err_io;
@@ -109,10 +109,7 @@ static void admhc_adm5120_remove(struct
usb_put_hcd(hcd);
}
-/*-------------------------------------------------------------------------*/
-
-static int __devinit
-admhc_adm5120_start(struct usb_hcd *hcd)
+static int __devinit admhc_adm5120_start(struct usb_hcd *hcd)
{
struct admhcd *ahcd = hcd_to_admhcd(hcd);
int ret;
@@ -137,8 +134,6 @@ err:
return ret;
}
-/*-------------------------------------------------------------------------*/
-
static const struct hc_driver adm5120_hc_driver = {
.description = hcd_name,
.product_desc = "ADM5120 built-in USB 1.1 Host Controller",
@@ -181,8 +176,6 @@ static const struct hc_driver adm5120_hc
.start_port_reset = admhc_start_port_reset,
};
-/*-------------------------------------------------------------------------*/
-
static int usb_hcd_adm5120_probe(struct platform_device *pdev)
{
int ret;
--- a/drivers/usb/host/adm5120-dbg.c
+++ b/drivers/usb/host/adm5120-dbg.c
@@ -401,25 +401,28 @@ static const struct file_operations debu
.open = debug_async_open,
.read = debug_output,
.release = debug_close,
+ .llseek = default_llseek,
};
static const struct file_operations debug_periodic_fops = {
.owner = THIS_MODULE,
.open = debug_periodic_open,
.read = debug_output,
.release = debug_close,
+ .llseek = default_llseek,
};
static const struct file_operations debug_registers_fops = {
.owner = THIS_MODULE,
.open = debug_registers_open,
.read = debug_output,
.release = debug_close,
+ .llseek = default_llseek,
};
static struct dentry *admhc_debug_root;
struct debug_buffer {
ssize_t (*fill_func)(struct debug_buffer *); /* fill method */
- struct device *dev;
+ struct admhcd *ahcd;
struct mutex mutex; /* protect filling of buffer */
size_t count; /* number of characters filled into buffer */
char *page;
@@ -494,15 +497,11 @@ show_list(struct admhcd *ahcd, char *buf
static ssize_t fill_async_buffer(struct debug_buffer *buf)
{
- struct usb_bus *bus;
- struct usb_hcd *hcd;
struct admhcd *ahcd;
size_t temp;
unsigned long flags;
- bus = dev_get_drvdata(buf->dev);
- hcd = bus_to_hcd(bus);
- ahcd = hcd_to_admhcd(hcd);
+ ahcd = buf->ahcd;
spin_lock_irqsave(&ahcd->lock, flags);
temp = show_list(ahcd, buf->page, PAGE_SIZE, ahcd->ed_head);
@@ -516,8 +515,6 @@ static ssize_t fill_async_buffer(struct
static ssize_t fill_periodic_buffer(struct debug_buffer *buf)
{
- struct usb_bus *bus;
- struct usb_hcd *hcd;
struct admhcd *ahcd;
struct ed **seen, *ed;
unsigned long flags;
@@ -530,9 +527,7 @@ static ssize_t fill_periodic_buffer(stru
return 0;
seen_count = 0;
- bus = dev_get_drvdata(buf->dev);
- hcd = bus_to_hcd(bus);
- ahcd = hcd_to_admhcd(hcd);
+ ahcd = buf->ahcd;
next = buf->page;
size = PAGE_SIZE;
@@ -615,7 +610,6 @@ static ssize_t fill_periodic_buffer(stru
static ssize_t fill_registers_buffer(struct debug_buffer *buf)
{
- struct usb_bus *bus;
struct usb_hcd *hcd;
struct admhcd *ahcd;
struct admhcd_regs __iomem *regs;
@@ -624,9 +618,8 @@ static ssize_t fill_registers_buffer(str
char *next;
u32 rdata;
- bus = dev_get_drvdata(buf->dev);
- hcd = bus_to_hcd(bus);
- ahcd = hcd_to_admhcd(hcd);
+ ahcd = buf->ahcd;
+ hcd = admhc_to_hcd(ahcd);
regs = ahcd->regs;
next = buf->page;
size = PAGE_SIZE;
@@ -638,13 +631,13 @@ static ssize_t fill_registers_buffer(str
admhc_dbg_sw(ahcd, &next, &size,
"bus %s, device %s\n"
"%s\n"
- "%s version " DRIVER_VERSION "\n",
+ "%s\n",
hcd->self.controller->bus->name,
dev_name(hcd->self.controller),
hcd->product_desc,
hcd_name);
- if (bus->controller->power.power_state.event) {
+ if (!HCD_HW_ACCESSIBLE(hcd)) {
size -= scnprintf(next, size,
"SUSPENDED (no register access)\n");
goto done;
@@ -691,7 +684,7 @@ done:
}
-static struct debug_buffer *alloc_buffer(struct device *dev,
+static struct debug_buffer *alloc_buffer(struct admhcd *ahcd,
ssize_t (*fill_func)(struct debug_buffer *))
{
struct debug_buffer *buf;
@@ -699,7 +692,7 @@ static struct debug_buffer *alloc_buffer
buf = kzalloc(sizeof(struct debug_buffer), GFP_KERNEL);
if (buf) {
- buf->dev = dev;
+ buf->ahcd = ahcd;
buf->fill_func = fill_func;
mutex_init(&buf->mutex);
}
@@ -792,26 +785,25 @@ static int debug_registers_open(struct i
static inline void create_debug_files(struct admhcd *ahcd)
{
struct usb_bus *bus = &admhcd_to_hcd(ahcd)->self;
- struct device *dev = bus->dev;
ahcd->debug_dir = debugfs_create_dir(bus->bus_name, admhc_debug_root);
if (!ahcd->debug_dir)
goto dir_error;
ahcd->debug_async = debugfs_create_file("async", S_IRUGO,
- ahcd->debug_dir, dev,
+ ahcd->debug_dir, ahcd,
&debug_async_fops);
if (!ahcd->debug_async)
goto async_error;
ahcd->debug_periodic = debugfs_create_file("periodic", S_IRUGO,
- ahcd->debug_dir, dev,
+ ahcd->debug_dir, ahcd,
&debug_periodic_fops);
if (!ahcd->debug_periodic)
goto periodic_error;
ahcd->debug_registers = debugfs_create_file("registers", S_IRUGO,
- ahcd->debug_dir, dev,
+ ahcd->debug_dir, ahcd,
&debug_registers_fops);
if (!ahcd->debug_registers)
goto registers_error;
--- a/drivers/usb/host/adm5120-pm.c
+++ b/drivers/usb/host/adm5120-pm.c
@@ -257,7 +257,7 @@ static int admhc_bus_suspend(struct usb_
spin_lock_irq(&ahcd->lock);
- if (unlikely(!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags)))
+ if (unlikely(!HCD_HW_ACCESSIBLE(hcd)))
rc = -ESHUTDOWN;
else
rc = admhc_rh_suspend(ahcd, 0);
@@ -275,7 +275,7 @@ static int admhc_bus_resume(struct usb_h
spin_lock_irq(&ahcd->lock);
- if (unlikely(!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags)))
+ if (unlikely(!HCD_HW_ACCESSIBLE(hcd)))
rc = -ESHUTDOWN;
else
rc = admhc_rh_resume(ahcd);
--- a/drivers/usb/host/adm5120-hcd.c
+++ b/drivers/usb/host/adm5120-hcd.c
@@ -32,9 +32,9 @@
#include <linux/list.h>
#include <linux/usb.h>
#include <linux/usb/otg.h>
+#include <linux/usb/hcd.h>
#include <linux/dma-mapping.h>
#include <linux/dmapool.h>
-#include <linux/reboot.h>
#include <linux/debugfs.h>
#include <linux/io.h>
@@ -43,9 +43,6 @@
#include <asm/unaligned.h>
#include <asm/byteorder.h>
-#include "../core/hcd.h"
-#include "../core/hub.h"
-
#define DRIVER_VERSION "0.27.0"
#define DRIVER_AUTHOR "Gabor Juhos <juhosg@openwrt.org>"
#define DRIVER_DESC "ADMtek USB 1.1 Host Controller Driver"
@@ -117,7 +114,7 @@ static int admhc_urb_enqueue(struct usb_
td_cnt = 2;
/* FALLTHROUGH */
case PIPE_BULK:
- /* one TD for every 4096 Bytes (can be upto 8K) */
+ /* one TD for every 4096 Bytes (can be up to 8K) */
td_cnt += urb->transfer_buffer_length / TD_DATALEN_MAX;
/* ... and for any remaining bytes ... */
if ((urb->transfer_buffer_length % TD_DATALEN_MAX) != 0)
@@ -153,7 +150,7 @@ static int admhc_urb_enqueue(struct usb_
spin_lock_irqsave(&ahcd->lock, flags);
/* don't submit to a dead HC */
- if (!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags)) {
+ if (!HCD_HW_ACCESSIBLE(hcd)) {
ret = -ENODEV;
goto fail;
}
@@ -321,7 +318,6 @@ sanitize:
ep->hcpriv = NULL;
spin_unlock_irqrestore(&ahcd->lock, flags);
- return;
}
static int admhc_get_frame_number(struct usb_hcd *hcd)
@@ -488,7 +484,7 @@ err:
*/
static int admhc_run(struct admhcd *ahcd)
{
- u32 temp;
+ u32 val;
int first = ahcd->fminterval == 0;
struct usb_hcd *hcd = admhcd_to_hcd(ahcd);
@@ -496,8 +492,8 @@ static int admhc_run(struct admhcd *ahcd
/* boot firmware should have set this up (5.1.1.3.1) */
if (first) {
- temp = admhc_readl(ahcd, &ahcd->regs->fminterval);
- ahcd->fminterval = temp & ADMHC_SFI_FI_MASK;
+ val = admhc_readl(ahcd, &ahcd->regs->fminterval);
+ ahcd->fminterval = val & ADMHC_SFI_FI_MASK;
if (ahcd->fminterval != FI)
admhc_dbg(ahcd, "fminterval delta %d\n",
ahcd->fminterval - FI);
@@ -507,30 +503,30 @@ static int admhc_run(struct admhcd *ahcd
}
#if 0 /* TODO: not applicable */
- /* Reset USB nearly "by the book". RemoteWakeupConnected was
- * saved if boot firmware (BIOS/SMM/...) told us it's connected,
- * or if bus glue did the same (e.g. for PCI add-in cards with
- * PCI PM support).
+ /* Reset USB nearly "by the book". RemoteWakeupConnected has
+ * to be checked in case boot firmware (BIOS/SMM/...) has set up
+ * wakeup in a way the bus isn't aware of (e.g., legacy PCI PM).
+ * If the bus glue detected wakeup capability then it should
+ * already be enabled; if so we'll just enable it again.
*/
- if ((ahcd->hc_control & OHCI_CTRL_RWC) != 0
- && !device_may_wakeup(hcd->self.controller))
- device_init_wakeup(hcd->self.controller, 1);
+ if ((ahcd->hc_control & OHCI_CTRL_RWC) != 0)
+ device_set_wakeup_capable(hcd->self.controller, 1);
#endif
switch (ahcd->host_control & ADMHC_HC_BUSS) {
case ADMHC_BUSS_OPER:
- temp = 0;
+ val = 0;
break;
case ADMHC_BUSS_SUSPEND:
/* FALLTHROUGH ? */
case ADMHC_BUSS_RESUME:
ahcd->host_control = ADMHC_BUSS_RESUME;
- temp = 10 /* msec wait */;
+ val = 10 /* msec wait */;
break;
/* case ADMHC_BUSS_RESET: */
default:
ahcd->host_control = ADMHC_BUSS_RESET;
- temp = 50 /* msec wait */;
+ val = 50 /* msec wait */;
break;
}
admhc_writel(ahcd, ahcd->host_control, &ahcd->regs->host_control);
@@ -538,12 +534,12 @@ static int admhc_run(struct admhcd *ahcd
/* flush the writes */
admhc_writel_flush(ahcd);
- msleep(temp);
- temp = admhc_read_rhdesc(ahcd);
- if (!(temp & ADMHC_RH_NPS)) {
+ msleep(val);
+ val = admhc_read_rhdesc(ahcd);
+ if (!(val & ADMHC_RH_NPS)) {
/* power down each port */
- for (temp = 0; temp < ahcd->num_ports; temp++)
- admhc_write_portstatus(ahcd, temp, ADMHC_PS_CPP);
+ for (val = 0; val < ahcd->num_ports; val++)
+ admhc_write_portstatus(ahcd, val, ADMHC_PS_CPP);
}
/* flush those writes */
admhc_writel_flush(ahcd);
@@ -552,9 +548,9 @@ static int admhc_run(struct admhcd *ahcd
spin_lock_irq(&ahcd->lock);
admhc_writel(ahcd, ADMHC_CTRL_SR, &ahcd->regs->gencontrol);
- temp = 30; /* ... allow extra time */
+ val = 30; /* ... allow extra time */
while ((admhc_readl(ahcd, &ahcd->regs->gencontrol) & ADMHC_CTRL_SR) != 0) {
- if (--temp == 0) {
+ if (--val == 0) {
spin_unlock_irq(&ahcd->lock);
admhc_err(ahcd, "USB HC reset timed out!\n");
return -1;
@@ -571,7 +567,7 @@ static int admhc_run(struct admhcd *ahcd
periodic_reinit(ahcd);
/* use rhsc irqs after khubd is fully initialized */
- hcd->poll_rh = 1;
+ set_bit(HCD_FLAG_POLL_RH, &hcd->flags);
hcd->uses_new_polling = 1;
#if 0
@@ -594,10 +590,10 @@ static int admhc_run(struct admhcd *ahcd
ahcd->host_control = ADMHC_BUSS_OPER;
admhc_writel(ahcd, ahcd->host_control, &ahcd->regs->host_control);
- temp = 20;
+ val = 20;
while ((admhc_readl(ahcd, &ahcd->regs->host_control)
& ADMHC_HC_BUSS) != ADMHC_BUSS_OPER) {
- if (--temp == 0) {
+ if (--val == 0) {
spin_unlock_irq(&ahcd->lock);
admhc_err(ahcd, "unable to setup operational mode!\n");
return -1;
@@ -613,10 +609,10 @@ static int admhc_run(struct admhcd *ahcd
/* FIXME: enabling DMA is always failed here for an unknown reason */
admhc_dma_enable(ahcd);
- temp = 200;
+ val = 200;
while ((admhc_readl(ahcd, &ahcd->regs->host_control)
& ADMHC_HC_DMAE) != ADMHC_HC_DMAE) {
- if (--temp == 0) {
+ if (--val == 0) {
spin_unlock_irq(&ahcd->lock);
admhc_err(ahcd, "unable to enable DMA!\n");
admhc_dump(ahcd, 1);
@@ -688,7 +684,7 @@ static irqreturn_t admhc_irq(struct usb_
*/
admhc_vdbg(ahcd, "Resume Detect\n");
admhc_intr_ack(ahcd, ADMHC_INTR_RESI);
- hcd->poll_rh = 1;
+ set_bit(HCD_FLAG_POLL_RH, &hcd->flags);
if (ahcd->autostop) {
spin_lock(&ahcd->lock);
admhc_rh_resume(ahcd);
@@ -799,9 +795,10 @@ static int __init admhc_hcd_mod_init(voi
pr_info("%s: " DRIVER_INFO "\n", hcd_name);
pr_info("%s: block sizes: ed %Zd td %Zd\n", hcd_name,
sizeof(struct ed), sizeof(struct td));
+ set_bit(USB_OHCI_LOADED, &usb_hcds_loaded);
#ifdef DEBUG
- admhc_debug_root = debugfs_create_dir("admhc", NULL);
+ admhc_debug_root = debugfs_create_dir("admhc", usb_debug_root);
if (!admhc_debug_root) {
ret = -ENOENT;
goto error_debug;
@@ -826,6 +823,7 @@ error_platform:
admhc_debug_root = NULL;
error_debug:
#endif
+ clear_bit(USB_OHCI_LOADED, &usb_hcds_loaded);
return ret;
}
module_init(admhc_hcd_mod_init);
@@ -836,6 +834,7 @@ static void __exit admhc_hcd_mod_exit(vo
#ifdef DEBUG
debugfs_remove(admhc_debug_root);
#endif
+ clear_bit(USB_OHCI_LOADED, &usb_hcds_loaded);
}
module_exit(admhc_hcd_mod_exit);
--- a/drivers/usb/host/adm5120-hub.c
+++ b/drivers/usb/host/adm5120-hub.c
@@ -75,7 +75,7 @@ admhc_hub_status_data(struct usb_hcd *hc
u32 status;
spin_lock_irqsave(&ahcd->lock, flags);
- if (!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags))
+ if (!HCD_HW_ACCESSIBLE(hcd))
goto done;
/* init status */
@@ -106,8 +106,11 @@ admhc_hub_status_data(struct usb_hcd *hc
}
}
- hcd->poll_rh = admhc_root_hub_state_changes(ahcd, changed,
- any_connected);
+ if (admhc_root_hub_state_changes(ahcd, changed,
+ any_connected))
+ set_bit(HCD_FLAG_POLL_RH, &hcd->flags);
+ else
+ clear_bit(HCD_FLAG_POLL_RH, &hcd->flags);
done:
spin_unlock_irqrestore(&ahcd->lock, flags);
@@ -143,9 +146,9 @@ static int admhc_get_hub_descriptor(stru
temp |= 0x0008;
desc->wHubCharacteristics = (__force __u16)cpu_to_hc16(ahcd, temp);
- /* two bitmaps: ports removable, and usb 1.0 legacy PortPwrCtrlMask */
- desc->bitmap[0] = 0;
- desc->bitmap[0] = ~0;
+ /* ports removable, and usb 1.0 legacy PortPwrCtrlMask */
+ desc->u.hs.DeviceRemovable[0] = 0;
+ desc->u.hs.DeviceRemovable[0] = ~0;
return 0;
}
@@ -310,10 +313,10 @@ static int admhc_hub_control(struct usb_
u16 wIndex, char *buf, u16 wLength)
{
struct admhcd *ahcd = hcd_to_admhcd(hcd);
- int ports = hcd_to_bus(hcd)->root_hub->maxchild;
+ int ports = ahcd->num_ports;
int ret = 0;
- if (unlikely(!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags)))
+ if (unlikely(!HCD_HW_ACCESSIBLE(hcd)))
return -ESHUTDOWN;
switch (typeReq) {
--- a/drivers/usb/host/adm5120-q.c
+++ b/drivers/usb/host/adm5120-q.c
@@ -14,6 +14,7 @@
*/
#include <linux/irq.h>
+#include <linux/slab.h>
/*-------------------------------------------------------------------------*/
@@ -300,7 +301,7 @@ static struct ed *ed_get(struct admhcd *
u32 info;
/* FIXME: usbcore changes dev->devnum before SET_ADDRESS
- * suceeds ... otherwise we wouldn't need "pipe".
+ * succeeds ... otherwise we wouldn't need "pipe".
*/
info = usb_pipedevice(pipe);
info |= (ep->desc.bEndpointAddress & ~USB_DIR_IN) << ED_EN_SHIFT;
@@ -634,8 +635,7 @@ static int td_done(struct admhcd *ahcd,
/*-------------------------------------------------------------------------*/
-static inline void
-ed_halted(struct admhcd *ahcd, struct td *td, int cc, struct td *rev)
+static void ed_halted(struct admhcd *ahcd, struct td *td, int cc)
{
struct urb *urb = td->urb;
struct urb_priv *urb_priv = urb->hcpriv;
@@ -764,6 +764,7 @@ rescan_this:
struct urb *urb;
struct urb_priv *urb_priv;
__hc32 savebits;
+ u32 tdINFO;
int status;
td = list_entry(entry, struct td, td_list);
@@ -781,6 +782,16 @@ rescan_this:
/* patch pointer hc uses */
savebits = *prev & ~cpu_to_hc32(ahcd, TD_MASK);
*prev = td->hwNextTD | savebits;
+ /* If this was unlinked, the TD may not have been
+ * retired ... so manually save dhe data toggle.
+ * The controller ignores the value we save for
+ * control and ISO endpoints.
+ */
+ tdINFO = hc32_to_cpup(ahcd, &td->hwINFO);
+ if ((tdINFO & TD_T) == TD_T_DATA0)
+ ed->hwHeadP &= ~cpu_to_hc32(ahcd, ED_C);
+ else if ((tdINFO & TD_T) == TD_T_DATA1)
+ ed->hwHeadP |= cpu_to_hc32(ahcd, ED_C);
/* HC may have partly processed this TD */
#ifdef ADMHC_VERBOSE_DEBUG
@@ -816,13 +827,12 @@ rescan_this:
}
/*-------------------------------------------------------------------------*/
-
/*
* Process normal completions (error or success) and clean the schedules.
*
* This is the main path for handing urbs back to drivers. The only other
- * path is finish_unlinks(), which unlinks URBs using ed_rm_list, instead of
- * scanning the (re-reversed) donelist as this does.
+ * normal path is finish_unlinks(), which unlinks URBs using ed_rm_list,
+ * instead of scanning the (re-reversed) donelist as this does.
*/
static void ed_unhalt(struct admhcd *ahcd, struct ed *ed, struct urb *urb)

View File

@ -0,0 +1,191 @@
CONFIG_ADM5120=y
CONFIG_ADM5120_ENET=y
# CONFIG_ADM5120_MACH_5GXI is not set
CONFIG_ADM5120_MACH_P_334WT=y
CONFIG_ADM5120_MACH_P_335=y
# CONFIG_ADM5120_OEM_CELLVISION is not set
# CONFIG_ADM5120_OEM_COMPEX is not set
# CONFIG_ADM5120_OEM_EDIMAX is not set
# CONFIG_ADM5120_OEM_GENERIC is not set
# CONFIG_ADM5120_OEM_INFINEON is not set
# CONFIG_ADM5120_OEM_MIKROTIK is not set
# CONFIG_ADM5120_OEM_MOTOROLA is not set
# CONFIG_ADM5120_OEM_OSBRIDGE is not set
CONFIG_ADM5120_OEM_ZYXEL=y
CONFIG_ADM5120_SOC_BGA=y
CONFIG_ADM5120_WDT=y
CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y
CONFIG_ARCH_DISCARD_MEMBLOCK=y
# CONFIG_ARCH_DMA_ADDR_T_64BIT is not set
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_HIBERNATION_POSSIBLE=y
# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set
CONFIG_ARCH_REQUIRE_GPIOLIB=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
CONFIG_ARCH_SUSPEND_POSSIBLE=y
CONFIG_ARM_AMBA=y
# CONFIG_ARM_SP805_WATCHDOG is not set
CONFIG_ATA=m
CONFIG_BCMA_POSSIBLE=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_CEVT_R4K=y
CONFIG_CEVT_R4K_LIB=y
CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,yaffs2,jffs2"
CONFIG_CMDLINE_BOOL=y
# CONFIG_CMDLINE_OVERRIDE is not set
CONFIG_CPU_BIG_ENDIAN=y
CONFIG_CPU_HAS_PREFETCH=y
CONFIG_CPU_HAS_SYNC=y
# CONFIG_CPU_LITTLE_ENDIAN is not set
CONFIG_CPU_MIPS32=y
CONFIG_CPU_MIPS32_R1=y
CONFIG_CPU_MIPSR1=y
CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
CONFIG_CPU_SUPPORTS_HIGHMEM=y
CONFIG_CRYPTO=m
CONFIG_CRYPTO_AEAD2=m
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_ALGAPI=m
CONFIG_CRYPTO_ALGAPI2=m
CONFIG_CRYPTO_ARC4=m
CONFIG_CRYPTO_BLKCIPHER=m
CONFIG_CRYPTO_BLKCIPHER2=m
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_HASH=m
CONFIG_CRYPTO_HASH2=m
CONFIG_CRYPTO_MANAGER=m
CONFIG_CRYPTO_MANAGER2=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_PCOMP2=m
CONFIG_CRYPTO_RNG2=m
CONFIG_CRYPTO_WORKQUEUE=m
CONFIG_CSRC_R4K=y
CONFIG_CSRC_R4K_LIB=y
CONFIG_DECOMPRESS_LZMA=y
CONFIG_DMA_NONCOHERENT=y
CONFIG_EARLY_PRINTK=y
CONFIG_FIRMWARE_IN_KERNEL=y
CONFIG_GENERIC_ATOMIC64=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
CONFIG_GENERIC_CMOS_UPDATE=y
# CONFIG_GENERIC_CPU_DEVICES is not set
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_IRQ_SHOW=y
CONFIG_GENERIC_PCI_IOMAP=y
CONFIG_GPIOLIB=y
# CONFIG_GPIO_PL061 is not set
CONFIG_GPIO_SYSFS=y
CONFIG_HARDWARE_WATCHPOINTS=y
CONFIG_HAS_DMA=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAVE_ARCH_JUMP_LABEL=y
CONFIG_HAVE_ARCH_KGDB=y
CONFIG_HAVE_C_RECORDMCOUNT=y
CONFIG_HAVE_DMA_API_DEBUG=y
CONFIG_HAVE_DMA_ATTRS=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_HAVE_GENERIC_HARDIRQS=y
CONFIG_HAVE_IDE=y
CONFIG_HAVE_IRQ_WORK=y
CONFIG_HAVE_MEMBLOCK=y
CONFIG_HAVE_MEMBLOCK_NODE_MAP=y
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_PERF_EVENTS=y
CONFIG_HID=m
CONFIG_HID_SUPPORT=y
CONFIG_HOSTAP=m
CONFIG_HOSTAP_FIRMWARE=y
# CONFIG_HOSTAP_FIRMWARE_NVRAM is not set
CONFIG_HOSTAP_PCI=m
CONFIG_HW_HAS_PCI=y
CONFIG_HW_RANDOM=y
CONFIG_HZ=250
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_IMAGE_CMDLINE_HACK=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_INPUT=m
# CONFIG_IP_MROUTE_MULTIPLE_TABLES is not set
CONFIG_IRQ_CPU=y
CONFIG_IRQ_FORCED_THREADING=y
# CONFIG_LEDS_GPIO is not set
# CONFIG_LEDS_TRIGGER_ADM5120_SWITCH is not set
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
CONFIG_LIB80211=m
CONFIG_LIB80211_CRYPT_CCMP=m
CONFIG_LIB80211_CRYPT_TKIP=m
CONFIG_LIB80211_CRYPT_WEP=m
CONFIG_MII=m
# CONFIG_MINIX_FS_NATIVE_ENDIAN is not set
CONFIG_MIPS=y
CONFIG_MIPS_L1_CACHE_SHIFT=5
CONFIG_MIPS_MACHINE=y
CONFIG_MIPS_MT_DISABLED=y
# CONFIG_MLX4_CORE is not set
CONFIG_MTD_ADM5120=y
CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC=y
# CONFIG_MTD_CFI_INTELEXT is not set
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_JEDECPROBE=y
CONFIG_MTD_TRXSPLIT=y
CONFIG_NEED_DMA_MAP_STATE=y
CONFIG_NEED_PER_CPU_KM=y
CONFIG_NLS=m
CONFIG_NO_EXCEPT_FILL=y
CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y
CONFIG_NO_HZ=y
CONFIG_PAGEFLAGS_EXTENDED=y
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_PCI=y
CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
CONFIG_PCI_DOMAINS=y
CONFIG_PERF_USE_VMALLOC=y
# CONFIG_PREEMPT_RCU is not set
# CONFIG_QUOTACTL is not set
CONFIG_SCSI=m
CONFIG_SCSI_MOD=m
# CONFIG_SERIAL_8250 is not set
CONFIG_SERIAL_AMBA_PL010=y
CONFIG_SERIAL_AMBA_PL010_CONSOLE=y
CONFIG_SERIAL_AMBA_PL010_NUMPORTS=2
CONFIG_SERIAL_AMBA_PL010_PORTNAME="ttyS"
# CONFIG_SERIAL_AMBA_PL011 is not set
CONFIG_SERIO=y
# CONFIG_SERIO_AMBAKMI is not set
# CONFIG_SERIO_I8042 is not set
# CONFIG_SERIO_LIBPS2 is not set
# CONFIG_SERIO_PCIPS2 is not set
# CONFIG_SERIO_RAW is not set
CONFIG_SERIO_SERPORT=y
CONFIG_SOFT_WATCHDOG=m
# CONFIG_SWAP is not set
CONFIG_SWAP_IO_SPACE=y
CONFIG_SYS_HAS_CPU_MIPS32_R1=y
CONFIG_SYS_HAS_EARLY_PRINTK=y
CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
CONFIG_USB=m
CONFIG_USB_ADM5120_HCD=m
CONFIG_USB_ARCH_HAS_XHCI=y
CONFIG_USB_COMMON=m
CONFIG_USB_EHCI_HCD=m
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_HCD=m
CONFIG_USB_SUPPORT=y
# CONFIG_USB_UHCI_HCD is not set
CONFIG_XZ_DEC=y
CONFIG_ZONE_DMA_FLAG=0

View File

@ -0,0 +1,227 @@
CONFIG_ADM5120=y
CONFIG_ADM5120_ENET=y
CONFIG_ADM5120_MACH_5GXI=y
CONFIG_ADM5120_MACH_BR_6104K=y
CONFIG_ADM5120_MACH_BR_6104KP=y
CONFIG_ADM5120_MACH_BR_61X4WG=y
CONFIG_ADM5120_MACH_CAS_771=y
CONFIG_ADM5120_MACH_EASY5120P_ATA=y
CONFIG_ADM5120_MACH_EASY5120_RT=y
CONFIG_ADM5120_MACH_EASY5120_WVOIP=y
CONFIG_ADM5120_MACH_EASY83000=y
CONFIG_ADM5120_MACH_EB_214A=y
CONFIG_ADM5120_MACH_NFS_101=y
CONFIG_ADM5120_MACH_NP27G=y
CONFIG_ADM5120_MACH_NP28G=y
CONFIG_ADM5120_MACH_PMUGW=y
CONFIG_ADM5120_MACH_RB_11X=y
CONFIG_ADM5120_MACH_RB_133=y
CONFIG_ADM5120_MACH_RB_133C=y
CONFIG_ADM5120_MACH_RB_150=y
CONFIG_ADM5120_MACH_RB_153=y
CONFIG_ADM5120_MACH_RB_192=y
CONFIG_ADM5120_MACH_WP54=y
CONFIG_ADM5120_OEM_CELLVISION=y
CONFIG_ADM5120_OEM_COMPEX=y
CONFIG_ADM5120_OEM_EDIMAX=y
CONFIG_ADM5120_OEM_GENERIC=y
CONFIG_ADM5120_OEM_INFINEON=y
CONFIG_ADM5120_OEM_MIKROTIK=y
CONFIG_ADM5120_OEM_MOTOROLA=y
CONFIG_ADM5120_OEM_OSBRIDGE=y
# CONFIG_ADM5120_OEM_ZYXEL is not set
CONFIG_ADM5120_SOC_BGA=y
CONFIG_ADM5120_WDT=y
CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y
CONFIG_ARCH_DISCARD_MEMBLOCK=y
# CONFIG_ARCH_DMA_ADDR_T_64BIT is not set
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_HIBERNATION_POSSIBLE=y
# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set
CONFIG_ARCH_REQUIRE_GPIOLIB=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
CONFIG_ARCH_SUSPEND_POSSIBLE=y
CONFIG_ARM_AMBA=y
# CONFIG_ARM_SP805_WATCHDOG is not set
CONFIG_ATA=m
CONFIG_BCMA_POSSIBLE=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_CEVT_R4K=y
CONFIG_CEVT_R4K_LIB=y
CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,yaffs2,jffs2"
CONFIG_CMDLINE_BOOL=y
# CONFIG_CMDLINE_OVERRIDE is not set
# CONFIG_CPU_BIG_ENDIAN is not set
CONFIG_CPU_HAS_PREFETCH=y
CONFIG_CPU_HAS_SYNC=y
CONFIG_CPU_LITTLE_ENDIAN=y
CONFIG_CPU_MIPS32=y
CONFIG_CPU_MIPS32_R1=y
CONFIG_CPU_MIPSR1=y
CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
CONFIG_CPU_SUPPORTS_HIGHMEM=y
CONFIG_CRYPTO=m
CONFIG_CRYPTO_AEAD2=m
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_ALGAPI=m
CONFIG_CRYPTO_ALGAPI2=m
CONFIG_CRYPTO_ARC4=m
CONFIG_CRYPTO_BLKCIPHER=m
CONFIG_CRYPTO_BLKCIPHER2=m
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_HASH=m
CONFIG_CRYPTO_HASH2=m
CONFIG_CRYPTO_MANAGER=m
CONFIG_CRYPTO_MANAGER2=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_PCOMP2=m
CONFIG_CRYPTO_RNG2=m
CONFIG_CRYPTO_WORKQUEUE=m
CONFIG_CSRC_R4K=y
CONFIG_CSRC_R4K_LIB=y
CONFIG_DECOMPRESS_LZMA=y
CONFIG_DMA_NONCOHERENT=y
CONFIG_EARLY_PRINTK=y
CONFIG_FIRMWARE_IN_KERNEL=y
CONFIG_GENERIC_ATOMIC64=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
CONFIG_GENERIC_CMOS_UPDATE=y
# CONFIG_GENERIC_CPU_DEVICES is not set
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_IRQ_SHOW=y
CONFIG_GENERIC_PCI_IOMAP=y
CONFIG_GPIOLIB=y
# CONFIG_GPIO_PL061 is not set
CONFIG_GPIO_SYSFS=y
CONFIG_HARDWARE_WATCHPOINTS=y
CONFIG_HAS_DMA=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAVE_ARCH_JUMP_LABEL=y
CONFIG_HAVE_ARCH_KGDB=y
CONFIG_HAVE_C_RECORDMCOUNT=y
CONFIG_HAVE_DMA_API_DEBUG=y
CONFIG_HAVE_DMA_ATTRS=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_HAVE_GENERIC_HARDIRQS=y
CONFIG_HAVE_IDE=y
CONFIG_HAVE_IRQ_WORK=y
CONFIG_HAVE_MEMBLOCK=y
CONFIG_HAVE_MEMBLOCK_NODE_MAP=y
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_PERF_EVENTS=y
CONFIG_HID=m
CONFIG_HID_SUPPORT=y
CONFIG_HOSTAP=m
CONFIG_HOSTAP_FIRMWARE=y
# CONFIG_HOSTAP_FIRMWARE_NVRAM is not set
CONFIG_HOSTAP_PCI=m
CONFIG_HW_HAS_PCI=y
CONFIG_HW_RANDOM=y
CONFIG_HZ=250
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_IMAGE_CMDLINE_HACK=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_INPUT=m
# CONFIG_IP_MROUTE_MULTIPLE_TABLES is not set
CONFIG_IRQ_CPU=y
CONFIG_IRQ_FORCED_THREADING=y
# CONFIG_LEDS_GPIO is not set
# CONFIG_LEDS_TRIGGER_ADM5120_SWITCH is not set
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
CONFIG_LIB80211=m
CONFIG_LIB80211_CRYPT_CCMP=m
CONFIG_LIB80211_CRYPT_TKIP=m
CONFIG_LIB80211_CRYPT_WEP=m
CONFIG_MII=m
# CONFIG_MINIX_FS_NATIVE_ENDIAN is not set
CONFIG_MIPS=y
CONFIG_MIPS_L1_CACHE_SHIFT=5
CONFIG_MIPS_MACHINE=y
CONFIG_MIPS_MT_DISABLED=y
# CONFIG_MLX4_CORE is not set
CONFIG_MTD_ADM5120=y
CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC=y
# CONFIG_MTD_CFI_INTELEXT is not set
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_JEDECPROBE=y
CONFIG_MTD_MYLOADER_PARTS=y
CONFIG_MTD_NAND=y
CONFIG_MTD_NAND_ECC=y
CONFIG_MTD_NAND_PLATFORM=y
# CONFIG_MTD_SM_COMMON is not set
CONFIG_MTD_TRXSPLIT=y
CONFIG_NEED_DMA_MAP_STATE=y
CONFIG_NEED_PER_CPU_KM=y
CONFIG_NLS=m
CONFIG_NO_EXCEPT_FILL=y
CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y
CONFIG_NO_HZ=y
CONFIG_PAGEFLAGS_EXTENDED=y
# CONFIG_PARTITION_ADVANCED is not set
# CONFIG_PATA_RB153_CF is not set
CONFIG_PCI=y
CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
CONFIG_PCI_DOMAINS=y
CONFIG_PERF_USE_VMALLOC=y
# CONFIG_PREEMPT_RCU is not set
# CONFIG_QUOTACTL is not set
CONFIG_SCSI=m
CONFIG_SCSI_MOD=m
# CONFIG_SERIAL_8250 is not set
CONFIG_SERIAL_AMBA_PL010=y
CONFIG_SERIAL_AMBA_PL010_CONSOLE=y
CONFIG_SERIAL_AMBA_PL010_NUMPORTS=2
CONFIG_SERIAL_AMBA_PL010_PORTNAME="ttyS"
# CONFIG_SERIAL_AMBA_PL011 is not set
CONFIG_SERIO=y
# CONFIG_SERIO_AMBAKMI is not set
# CONFIG_SERIO_I8042 is not set
# CONFIG_SERIO_LIBPS2 is not set
# CONFIG_SERIO_PCIPS2 is not set
# CONFIG_SERIO_RAW is not set
CONFIG_SERIO_SERPORT=y
CONFIG_SOFT_WATCHDOG=m
# CONFIG_SWAP is not set
CONFIG_SYS_HAS_CPU_MIPS32_R1=y
CONFIG_SYS_HAS_EARLY_PRINTK=y
CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
CONFIG_USB=m
CONFIG_USB_ADM5120_HCD=m
CONFIG_USB_ARCH_HAS_XHCI=y
CONFIG_USB_COMMON=m
CONFIG_USB_EHCI_HCD=m
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_HCD=m
CONFIG_USB_SUPPORT=y
# CONFIG_USB_UHCI_HCD is not set
CONFIG_XZ_DEC=y
CONFIG_YAFFS_9BYTE_TAGS=y
# CONFIG_YAFFS_ALWAYS_CHECK_CHUNK_ERASED is not set
CONFIG_YAFFS_AUTO_YAFFS2=y
# CONFIG_YAFFS_DISABLE_BACKGROUND is not set
# CONFIG_YAFFS_DISABLE_BLOCK_REFRESHING is not set
CONFIG_YAFFS_DISABLE_TAGS_ECC=y
# CONFIG_YAFFS_DISABLE_WIDE_TNODES is not set
# CONFIG_YAFFS_EMPTY_LOST_AND_FOUND is not set
CONFIG_YAFFS_FS=y
CONFIG_YAFFS_SHORT_NAMES_IN_RAM=y
CONFIG_YAFFS_XATTR=y
CONFIG_YAFFS_YAFFS1=y
CONFIG_YAFFS_YAFFS2=y
CONFIG_ZONE_DMA_FLAG=0