[package] Add uboot for xburst package

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@20832 3c298f89-4303-0410-b956-a3cf2f4a3e73

package/uboot-xburst/Makefile

@@ -0,0 +1,102 @@
+#
+# Copyright (C) 2008 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+include $(TOPDIR)/rules.mk
+include $(INCLUDE_DIR)/kernel.mk
+
+PKG_NAME:=u-boot
+PKG_VERSION:=2009.11
+PKG_RELEASE:=1
+
+PKG_BUILD_DIR:=$(KERNEL_BUILD_DIR)/$(PKG_NAME)-$(BUILD_VARIANT)/$(PKG_NAME)-$(PKG_VERSION)
+PKG_SOURCE:=$(PKG_NAME)-$(PKG_VERSION).tar.bz2
+PKG_SOURCE_URL:=ftp://ftp.denx.de/pub/u-boot
+PKG_MD5SUM:=
+PKG_TARGETS:=bin
+
+include $(INCLUDE_DIR)/package.mk
+
+define uboot/Default
+  TITLE:=
+  CONFIG:=
+  IMAGE:=
+endef
+
+define uboot/qi_lb60
+  TITLE:=U-boot for the qi_lb60 board
+endef
+
+define uboot/avt2
+  TITLE:=U-boot for the avt2 board
+endef
+
+define uboot/sakc
+  TITLE:=U-boot for the sakc board
+endef
+
+define uboot/n516
+  TITLE:=U-boot for the N516 e-book reader
+  CONFIG:=n516_nand
+endef
+
+UBOOTS:=qi_lb60 n516 avt2 sakc
+
+define Package/uboot/template
+define Package/uboot-xburst-$(1)
+  SECTION:=boot
+  CATEGORY:=Boot Loaders
+  DEPENDS:=@TARGET_xburst
+  TITLE:=$(2)
+  URL:=http://www.denx.de/wiki/UBoot/WebHome
+  VARIANT:=$(1)
+endef
+endef
+
+define BuildUbootPackage
+	$(eval $(uboot/Default))
+	$(eval $(uboot/$(1)))
+	$(call Package/uboot/template,$(1),$(TITLE))
+endef
+
+
+ifdef BUILD_VARIANT
+$(eval $(call uboot/$(BUILD_VARIANT)))
+UBOOT_CONFIG:=$(if $(CONFIG),$(CONFIG),$(BUILD_VARIANT))
+UBOOT_IMAGE:=$(if $(IMAGE),$(IMAGE),openwrt-$(BOARD)-$(BUILD_BARIANT)-u-boot.bin)
+endif
+
+define Build/Prepare
+	$(call Build/Prepare/Default)
+	$(CP) ./files/* $(PKG_BUILD_DIR)
+	find $(PKG_BUILD_DIR) -name .svn | $(XARGS) rm -rf
+endef
+
+define Build/Configure
+	$(MAKE) -C $(PKG_BUILD_DIR) \
+		$(UBOOT_CONFIG)_config
+endef
+
+define Build/Compile
+	$(MAKE) -C $(PKG_BUILD_DIR) \
+		CROSS_COMPILE=$(TARGET_CROSS)
+endef
+
+define Package/uboot/install/template
+define Package/uboot-xburst-$(1)/install
+	$(INSTALL_DIR) $$(1)
+	$(CP) $(PKG_BUILD_DIR)/u-boot-nand.bin $(BIN_DIR)/$(2)
+endef
+endef
+
+$(foreach u,$(UBOOTS), \
+	$(eval $(call Package/uboot/install/template,$(u),openwrt-$(BOARD)-$(u)-u-boot.bin)) \
+)
+
+$(foreach u,$(UBOOTS), \
+	$(eval $(call BuildUbootPackage,$(u))) \
+	$(eval $(call BuildPackage,uboot-xburst-$(u))) \
+)

package/uboot-xburst/files/board/n516/Makefile

@@ -0,0 +1,40 @@
+#
+# (C) Copyright 2006
+# Ingenic Semiconductor, <jlwei@ingenic.cn>
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	= $(BOARD).o flash.o
+
+OBJS	= $(addprefix $(obj),$(COBJS))
+SOBJS	= 
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS) $(SOBJS)
+
+#########################################################################
+
+$(obj).depend:	Makefile $(SOBJS:.o=.S) $(COBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(COBJS:.o=.c) > $@
+
+sinclude $(obj).depend
+
+#########################################################################

package/uboot-xburst/files/board/n516/config.mk

@@ -0,0 +1,33 @@
+#
+# (C) Copyright 2006
+# Ingenic Semiconductor, <jlwei@ingenic.cn>
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# Hanvon n516 e-book, MIPS32 core
+#
+
+sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp
+
+ifndef TEXT_BASE
+# ROM version
+TEXT_BASE = 0x88000000
+
+# RAM version
+#TEXT_BASE = 0x80100000
+endif

package/uboot-xburst/files/board/n516/flash.c

@@ -0,0 +1,50 @@
+/*
+ * (C) Copyright 2006
+ * Ingenic Semiconductor, <jlwei@ingenic.cn>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];	/* info for FLASH chips */
+
+/*-----------------------------------------------------------------------
+ * flash_init()
+ *
+ * sets up flash_info and returns size of FLASH (bytes)
+ */
+unsigned long flash_init (void)
+{
+	return (0);
+}
+
+int flash_erase (flash_info_t * info, int s_first, int s_last)
+{
+	printf ("flash_erase not implemented\n");
+	return 0;
+}
+
+void flash_print_info (flash_info_t * info)
+{
+	printf ("flash_print_info not implemented\n");
+}
+
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+	printf ("write_buff not implemented\n");
+	return (-1);
+}

package/uboot-xburst/files/board/n516/n516.c

@@ -0,0 +1,126 @@
+/*
+ * (C) Copyright 2006
+ * Ingenic Semiconductor, <jlwei@ingenic.cn>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/mipsregs.h>
+#include <asm/jz4740.h>
+#include <asm/addrspace.h>
+#include <asm/cacheops.h>
+
+void _machine_restart(void)
+{
+	__wdt_select_extalclk();
+	__wdt_select_clk_div64();
+	__wdt_set_data(100);
+	__wdt_set_count(0);
+	__tcu_start_wdt_clock();
+	__wdt_start();
+	while(1);
+
+}
+
+static void gpio_init(void)
+{
+
+	REG_GPIO_PXPES(0) = 0xffffffff;
+	REG_GPIO_PXPES(1) = 0xffffffff;
+	REG_GPIO_PXPES(2) = 0xffffffff;
+	REG_GPIO_PXPES(3) = 0xffffffff;
+
+	/*
+	 * Initialize NAND Flash Pins
+	 */
+	__gpio_as_nand();
+
+	/*
+	 * Initialize SDRAM pins
+	 */
+	__gpio_as_sdram_32bit();
+
+	/*
+	 * Initialize UART0 pins
+	 */
+	__gpio_as_uart0();
+
+	/*
+	 * Initialize MSC pins
+	 */
+	__gpio_as_msc();
+
+	/*
+	 * Initialize LCD pins
+	 */
+	__gpio_as_lcd_16bit();
+
+	/*
+	 * Initialize Other pins
+	 */
+	__gpio_as_output(GPIO_SD_VCC_EN_N);
+	__gpio_clear_pin(GPIO_SD_VCC_EN_N);
+
+	__gpio_as_input(GPIO_SD_CD_N);
+	__gpio_disable_pull(GPIO_SD_CD_N);
+
+	__gpio_as_output(GPIO_DISP_OFF_N);
+
+	__gpio_as_output(GPIO_LED_EN);
+	__gpio_set_pin(GPIO_LED_EN);
+
+	__gpio_as_input(127);
+}
+
+static void cpm_init(void)
+{
+	__cpm_stop_ipu();
+	__cpm_stop_cim();
+	__cpm_stop_i2c();
+	__cpm_stop_ssi();
+	__cpm_stop_uart1();
+	__cpm_stop_sadc();
+	__cpm_stop_uhc();
+	__cpm_stop_udc();
+	__cpm_stop_aic1();
+	__cpm_stop_aic2();
+	__cpm_suspend_udcphy();
+	__cpm_suspend_usbphy();
+}
+
+//----------------------------------------------------------------------
+// board early init routine
+
+void board_early_init(void)
+{
+	gpio_init();
+	cpm_init();
+}
+
+//----------------------------------------------------------------------
+// U-Boot common routines
+
+int checkboard (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	printf("Board: Hanvon n516 e-book (CPU Speed %d MHz)\n",
+	       gd->cpu_clk/1000000);
+
+	return 0; /* success */
+}

package/uboot-xburst/files/board/n516/u-boot-nand.lds

@@ -0,0 +1,63 @@
+/*
+ * (C) Copyright 2006
+ * Ingenic Semiconductor, <jlwei@ingenic.cn>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-tradlittlemips", "elf32-tradlittlemips", "elf32-tradlittlemips")
+
+OUTPUT_ARCH(mips)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text       :
+	{
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata  : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data  : { *(.data) }
+
+	. = ALIGN(4);
+	.sdata  : { *(.sdata) }
+
+	_gp = ALIGN(16);
+
+	__got_start = .;
+	.got  : { *(.got) }
+	__got_end = .;
+
+	.sdata  : { *(.sdata) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	uboot_end_data = .;
+	num_got_entries = (__got_end - __got_start) >> 2;
+
+	. = ALIGN(4);
+	.sbss  : { *(.sbss) }
+	.bss  : { *(.bss) }
+	uboot_end = .;
+}

package/uboot-xburst/files/board/n516/u-boot.lds

@@ -0,0 +1,63 @@
+/*
+ * (C) Copyright 2006
+ * Ingenic Semiconductor, <jlwei@ingenic.cn>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-tradlittlemips", "elf32-tradlittlemips", "elf32-tradlittlemips")
+
+OUTPUT_ARCH(mips)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text       :
+	{
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata  : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data  : { *(.data) }
+
+	. = ALIGN(4);
+	.sdata  : { *(.sdata) }
+
+	_gp = ALIGN(16);
+
+	__got_start = .;
+	.got  : { *(.got) }
+	__got_end = .;
+
+	.sdata  : { *(.sdata) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	uboot_end_data = .;
+	num_got_entries = (__got_end - __got_start) >> 2;
+
+	. = ALIGN(4);
+	.sbss  : { *(.sbss) }
+	.bss  : { *(.bss) }
+	uboot_end = .;
+}

package/uboot-xburst/files/board/nanonote/Makefile

@@ -0,0 +1,38 @@
+#
+# (C) Copyright 2006
+# Ingenic Semiconductor, <jlwei@ingenic.cn>
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	= $(BOARD).o
+SOBJS	=
+
+$(LIB):	.depend $(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS) $(SOBJS)
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

package/uboot-xburst/files/board/nanonote/config.mk

@@ -0,0 +1,31 @@
+#
+# (C) Copyright 2006 Qi Hardware, Inc.
+# Author: Xiangfu Liu <xiangfu.z@gmail.com>
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# Qi Hardware, Inc. Ben NanoNote (QI_LB60)
+#
+
+ifndef TEXT_BASE
+# ROM version
+# TEXT_BASE = 0x88000000
+
+# RAM version
+TEXT_BASE = 0x80100000
+endif

package/uboot-xburst/files/board/nanonote/nanonote.c

@@ -0,0 +1,123 @@
+/*
+ * Authors: Xiangfu Liu <xiangfu.z@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 3 of the License, or (at your option) any later version.
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/mipsregs.h>
+#include <asm/jz4740.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static void gpio_init(void)
+{
+	/*
+	 * Initialize NAND Flash Pins
+	 */
+	__gpio_as_nand();
+
+	/*
+	 * Initialize SDRAM pins
+	 */
+	__gpio_as_sdram_32bit();
+
+	/*
+	 * Initialize LCD pins
+	 */
+	__gpio_as_lcd_18bit();
+
+	/*
+	 * Initialize MSC pins
+	 */
+	__gpio_as_msc();
+
+	/*
+	 * Initialize Other pins
+	 */
+	unsigned int i;
+	for (i = 0; i < 7; i++){
+		__gpio_as_input(GPIO_KEYIN_BASE + i);
+		__gpio_enable_pull(GPIO_KEYIN_BASE + i);
+	}
+
+	for (i = 0; i < 8; i++) {
+		__gpio_as_output(GPIO_KEYOUT_BASE + i);
+		__gpio_clear_pin(GPIO_KEYOUT_BASE + i);
+	}
+
+	/*
+	 * Initialize UART0 pins, in Ben NanoNote uart0 and keyin8 use the
+	 * same gpio, init the gpio as uart0 cause a keyboard bug. so for
+	 * end user we disable the uart0
+	 */
+	if (__gpio_get_pin(GPIO_KEYIN_BASE + 2) == 0){
+		/* if pressed [S] */
+		printf("[S] pressed, enable UART0\n");
+		gd->boot_option = 5;
+		__gpio_as_uart0();
+	} else {
+		printf("[S] not pressed, disable UART0\n");
+		__gpio_as_input(GPIO_KEYIN_8);
+		__gpio_enable_pull(GPIO_KEYIN_8);
+	}
+
+	__gpio_as_output(GPIO_AUDIO_POP);
+	__gpio_set_pin(GPIO_AUDIO_POP);
+
+	__gpio_as_output(GPIO_LCD_CS);
+	__gpio_clear_pin(GPIO_LCD_CS);
+
+	__gpio_as_output(GPIO_AMP_EN);
+	__gpio_clear_pin(GPIO_AMP_EN);
+
+	__gpio_as_output(GPIO_SDPW_EN);
+	__gpio_disable_pull(GPIO_SDPW_EN);
+	__gpio_clear_pin(GPIO_SDPW_EN);
+
+	__gpio_as_input(GPIO_SD_DETECT);
+	__gpio_disable_pull(GPIO_SD_DETECT);
+
+	__gpio_as_input(GPIO_USB_DETECT);
+	__gpio_enable_pull(GPIO_USB_DETECT);
+
+	if (__gpio_get_pin(GPIO_KEYIN_BASE + 3) == 0) {
+		printf("[M] pressed, boot from sd card\n");
+		gd->boot_option = 1;
+	}
+}
+
+static void cpm_init(void)
+{
+	__cpm_stop_ipu();
+	__cpm_stop_cim();
+	__cpm_stop_i2c();
+	__cpm_stop_ssi();
+	__cpm_stop_uart1();
+	__cpm_stop_sadc();
+	__cpm_stop_uhc();
+	__cpm_stop_udc();
+	__cpm_stop_aic1();
+/*	__cpm_stop_aic2();*/
+}
+
+void board_early_init(void)
+{
+	gpio_init();
+	cpm_init();
+}
+
+/* U-Boot common routines */
+
+int checkboard (void)
+{
+
+	printf("Board: Qi LB60 (Ingenic XBurst Jz4740 SoC, Speed %d MHz)\n",
+	       gd->cpu_clk/1000000);
+
+	return 0; /* success */
+}

package/uboot-xburst/files/board/nanonote/u-boot-nand.lds

@@ -0,0 +1,63 @@
+/*
+ * (C) Copyright 2006
+ * Ingenic Semiconductor, <jlwei@ingenic.cn>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-tradlittlemips", "elf32-tradlittlemips", "elf32-tradlittlemips")
+
+OUTPUT_ARCH(mips)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text       :
+	{
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata  : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data  : { *(.data) }
+
+	. = ALIGN(4);
+	.sdata  : { *(.sdata) }
+
+	_gp = ALIGN(16);
+
+	__got_start = .;
+	.got  : { *(.got) }
+	__got_end = .;
+
+	.sdata  : { *(.sdata) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	uboot_end_data = .;
+	num_got_entries = (__got_end - __got_start) >> 2;
+
+	. = ALIGN(4);
+	.sbss  : { *(.sbss) }
+	.bss  : { *(.bss) }
+	uboot_end = .;
+}

package/uboot-xburst/files/board/nanonote/u-boot.lds

@@ -0,0 +1,63 @@
+/*
+ * (C) Copyright 2006
+ * Ingenic Semiconductor, <jlwei@ingenic.cn>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-tradlittlemips", "elf32-tradlittlemips", "elf32-tradlittlemips")
+
+OUTPUT_ARCH(mips)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text       :
+	{
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata  : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data  : { *(.data) }
+
+	. = ALIGN(4);
+	.sdata  : { *(.sdata) }
+
+	_gp = ALIGN(16);
+
+	__got_start = .;
+	.got  : { *(.got) }
+	__got_end = .;
+
+	.sdata  : { *(.sdata) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	uboot_end_data = .;
+	num_got_entries = (__got_end - __got_start) >> 2;
+
+	. = ALIGN(4);
+	.sbss  : { *(.sbss) }
+	.bss  : { *(.bss) }
+	uboot_end = .;
+}

package/uboot-xburst/files/board/sakc/Makefile

@@ -0,0 +1,38 @@
+#
+# (C) Copyright 2006
+# Ingenic Semiconductor, <jlwei@ingenic.cn>
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	= $(BOARD).o 
+SOBJS	= 
+
+$(LIB):	.depend $(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS) $(SOBJS)
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

package/uboot-xburst/files/board/sakc/config.mk

@@ -0,0 +1,31 @@
+#
+# (C) Copyright 2006 Qi Hardware, Inc.
+# Author: Xiangfu Liu <xiangfu.z@gmail.com>
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# SAKC Board
+#
+
+ifndef TEXT_BASE
+# ROM version
+# TEXT_BASE = 0x88000000
+
+# RAM version
+TEXT_BASE = 0x80100000
+endif

package/uboot-xburst/files/board/sakc/sakc.c

@@ -0,0 +1,94 @@
+/*
+ * Authors: Xiangfu Liu <xiangfu.z@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 3 of the License, or (at your option) any later version.
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/mipsregs.h>
+#include <asm/jz4740.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static void gpio_init(void)
+{
+	/*
+	 * Initialize NAND Flash Pins
+	 */
+	__gpio_as_nand();
+
+	/*
+	 * Initialize SDRAM pins
+	 */	
+	__gpio_as_sdram_16bit_4725();
+
+	/*
+	 * Initialize UART0 pins
+	 */
+	__gpio_as_uart0();
+
+	/*
+	 * Initialize LCD pins
+	 */
+	__gpio_as_lcd_18bit();
+
+	/*
+	 * Initialize MSC pins
+	 */
+	__gpio_as_msc();
+
+	/*
+	 * Initialize SSI pins
+	 */
+	__gpio_as_ssi();
+
+	/*
+	 * Initialize I2C pins
+	 */
+	__gpio_as_i2c();
+
+	/*
+	 * Initialize MSC pins
+	 */
+	__gpio_as_msc();
+
+	/*
+	 * Initialize Other pins
+	 */
+	__gpio_as_input(GPIO_SD_DETECT);
+	__gpio_disable_pull(GPIO_SD_DETECT);
+}
+/* TODO SAKC
+static void cpm_init(void)
+{
+	__cpm_stop_ipu();
+	__cpm_stop_cim();
+	__cpm_stop_i2c();
+	__cpm_stop_ssi();
+	__cpm_stop_uart1();
+	__cpm_stop_sadc();
+	__cpm_stop_uhc();
+	__cpm_stop_aic1();
+	__cpm_stop_aic2();
+}*/
+
+void board_early_init(void)
+{
+	gpio_init();
+	//cpm_init(); //TODO SAKC
+}
+
+/* U-Boot common routines */
+
+int checkboard (void)
+{
+
+	printf("Board: SAKC (Ingenic XBurst Jz4725 SoC, Speed %d MHz)\n",
+	       gd->cpu_clk/1000000);
+
+	return 0; /* success */
+}

package/uboot-xburst/files/board/sakc/u-boot-nand.lds

@@ -0,0 +1,63 @@
+/*
+ * (C) Copyright 2006
+ * Ingenic Semiconductor, <jlwei@ingenic.cn>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-tradlittlemips", "elf32-tradlittlemips", "elf32-tradlittlemips")
+
+OUTPUT_ARCH(mips)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text       :
+	{
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata  : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data  : { *(.data) }
+
+	. = ALIGN(4);
+	.sdata  : { *(.sdata) }
+
+	_gp = ALIGN(16);
+
+	__got_start = .;
+	.got  : { *(.got) }
+	__got_end = .;
+
+	.sdata  : { *(.sdata) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	uboot_end_data = .;
+	num_got_entries = (__got_end - __got_start) >> 2;
+
+	. = ALIGN(4);
+	.sbss  : { *(.sbss) }
+	.bss  : { *(.bss) }
+	uboot_end = .;
+}

package/uboot-xburst/files/board/sakc/u-boot.lds

@@ -0,0 +1,63 @@
+/*
+ * (C) Copyright 2006
+ * Ingenic Semiconductor, <jlwei@ingenic.cn>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-tradlittlemips", "elf32-tradlittlemips", "elf32-tradlittlemips")
+
+OUTPUT_ARCH(mips)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text       :
+	{
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata  : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data  : { *(.data) }
+
+	. = ALIGN(4);
+	.sdata  : { *(.sdata) }
+
+	_gp = ALIGN(16);
+
+	__got_start = .;
+	.got  : { *(.got) }
+	__got_end = .;
+
+	.sdata  : { *(.sdata) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	uboot_end_data = .;
+	num_got_entries = (__got_end - __got_start) >> 2;
+
+	. = ALIGN(4);
+	.sbss  : { *(.sbss) }
+	.bss  : { *(.bss) }
+	uboot_end = .;
+}

package/uboot-xburst/files/cpu/mips/jz4740.c

@@ -0,0 +1,559 @@
+/*
+ * Jz4740 common routines
+ *
+ *  Copyright (c) 2006
+ *  Ingenic Semiconductor, <jlwei@ingenic.cn>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+
+#ifdef CONFIG_JZ4740
+#include <common.h>
+#include <command.h>
+#include <asm/jz4740.h>
+
+extern void board_early_init(void);
+
+/* PLL output clock = EXTAL * NF / (NR * NO)
+ *
+ * NF = FD + 2, NR = RD + 2
+ * NO = 1 (if OD = 0), NO = 2 (if OD = 1 or 2), NO = 4 (if OD = 3)
+ */
+void pll_init(void)
+{
+	register unsigned int cfcr, plcr1;
+	int n2FR[33] = {
+		0, 0, 1, 2, 3, 0, 4, 0, 5, 0, 0, 0, 6, 0, 0, 0,
+		7, 0, 0, 0, 0, 0, 0, 0, 8, 0, 0, 0, 0, 0, 0, 0,
+		9
+	};
+	int div[5] = {1, 3, 3, 3, 3}; /* divisors of I:S:P:L:M */
+	int nf, pllout2;
+
+	cfcr = CPM_CPCCR_CLKOEN |
+		CPM_CPCCR_PCS |
+		(n2FR[div[0]] << CPM_CPCCR_CDIV_BIT) |
+		(n2FR[div[1]] << CPM_CPCCR_HDIV_BIT) |
+		(n2FR[div[2]] << CPM_CPCCR_PDIV_BIT) |
+		(n2FR[div[3]] << CPM_CPCCR_MDIV_BIT) |
+		(n2FR[div[4]] << CPM_CPCCR_LDIV_BIT);
+
+	pllout2 = (cfcr & CPM_CPCCR_PCS) ? CONFIG_SYS_CPU_SPEED : (CONFIG_SYS_CPU_SPEED / 2);
+
+	/* Init USB Host clock, pllout2 must be n*48MHz */
+	REG_CPM_UHCCDR = pllout2 / 48000000 - 1;
+
+	nf = CONFIG_SYS_CPU_SPEED * 2 / CONFIG_SYS_EXTAL;
+	plcr1 = ((nf - 2) << CPM_CPPCR_PLLM_BIT) | /* FD */
+		(0 << CPM_CPPCR_PLLN_BIT) |	/* RD=0, NR=2 */
+		(0 << CPM_CPPCR_PLLOD_BIT) |    /* OD=0, NO=1 */
+		(0x20 << CPM_CPPCR_PLLST_BIT) | /* PLL stable time */
+		CPM_CPPCR_PLLEN;                /* enable PLL */
+
+	/* init PLL */
+	REG_CPM_CPCCR = cfcr;
+	REG_CPM_CPPCR = plcr1;
+}
+
+void pll_add_test(int new_freq)
+{
+	register unsigned int cfcr, plcr1;
+	int n2FR[33] = {
+		0, 0, 1, 2, 3, 0, 4, 0, 5, 0, 0, 0, 6, 0, 0, 0,
+		7, 0, 0, 0, 0, 0, 0, 0, 8, 0, 0, 0, 0, 0, 0, 0,
+		9
+	};
+	int div[5] = {1, 4, 4, 4, 4}; /* divisors of I:S:P:M:L */
+	int nf, pllout2;
+
+	cfcr = CPM_CPCCR_CLKOEN |
+		(n2FR[div[0]] << CPM_CPCCR_CDIV_BIT) |
+		(n2FR[div[1]] << CPM_CPCCR_HDIV_BIT) |
+		(n2FR[div[2]] << CPM_CPCCR_PDIV_BIT) |
+		(n2FR[div[3]] << CPM_CPCCR_MDIV_BIT) |
+		(n2FR[div[4]] << CPM_CPCCR_LDIV_BIT);
+
+	pllout2 = (cfcr & CPM_CPCCR_PCS) ? new_freq : (new_freq / 2);
+
+	/* Init UHC clock */
+	REG_CPM_UHCCDR = pllout2 / 48000000 - 1;
+
+	/* nf = new_freq * 2 / CONFIG_SYS_EXTAL; */
+	nf = new_freq / 1000000; /* step length is 1M */
+	plcr1 = ((nf - 2) << CPM_CPPCR_PLLM_BIT) | /* FD */
+		(10 << CPM_CPPCR_PLLN_BIT) |	/* RD=0, NR=2 */
+		(0 << CPM_CPPCR_PLLOD_BIT) |    /* OD=0, NO=1 */
+		(0x20 << CPM_CPPCR_PLLST_BIT) | /* PLL stable time */
+		CPM_CPPCR_PLLEN;                /* enable PLL */
+
+	/* init PLL */
+	REG_CPM_CPCCR = cfcr;
+	REG_CPM_CPPCR = plcr1;
+}
+
+void calc_clocks_add_test(void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	unsigned int pllout;
+	unsigned int div[10] = {1, 2, 3, 4, 6, 8, 12, 16, 24, 32};
+
+	pllout = __cpm_get_pllout();
+
+	gd->cpu_clk = pllout / div[__cpm_get_cdiv()];
+	gd->sys_clk = pllout / div[__cpm_get_hdiv()];
+	gd->per_clk = pllout / div[__cpm_get_pdiv()];
+	gd->mem_clk = pllout / div[__cpm_get_mdiv()];
+	gd->dev_clk = CONFIG_SYS_EXTAL;
+}
+
+void sdram_add_test(int new_freq)
+{
+	register unsigned int dmcr, sdmode, tmp, cpu_clk, mem_clk, ns;
+
+	unsigned int cas_latency_sdmr[2] = {
+		EMC_SDMR_CAS_2,
+		EMC_SDMR_CAS_3,
+	};
+
+	unsigned int cas_latency_dmcr[2] = {
+		1 << EMC_DMCR_TCL_BIT,	/* CAS latency is 2 */
+		2 << EMC_DMCR_TCL_BIT	/* CAS latency is 3 */
+	};
+
+	int div[] = {1, 2, 3, 4, 6, 8, 12, 16, 24, 32};
+
+	cpu_clk = new_freq;
+	mem_clk = cpu_clk * div[__cpm_get_cdiv()] / div[__cpm_get_mdiv()];
+
+	REG_EMC_RTCSR = EMC_RTCSR_CKS_DISABLE;
+	REG_EMC_RTCOR = 0;
+	REG_EMC_RTCNT = 0;
+
+	/* Basic DMCR register value. */
+	dmcr = ((SDRAM_ROW-11)<<EMC_DMCR_RA_BIT) |
+		((SDRAM_COL-8)<<EMC_DMCR_CA_BIT) |
+		(SDRAM_BANK4<<EMC_DMCR_BA_BIT) |
+		(SDRAM_BW16<<EMC_DMCR_BW_BIT) |
+		EMC_DMCR_EPIN |
+		cas_latency_dmcr[((SDRAM_CASL == 3) ? 1 : 0)];
+
+	/* SDRAM timimg parameters */
+	ns = 1000000000 / mem_clk;
+
+#if 0
+	tmp = SDRAM_TRAS/ns;
+	if (tmp < 4) tmp = 4;
+	if (tmp > 11) tmp = 11;
+	dmcr |= ((tmp-4) << EMC_DMCR_TRAS_BIT);
+
+	tmp = SDRAM_RCD/ns;
+	if (tmp > 3) tmp = 3;
+	dmcr |= (tmp << EMC_DMCR_RCD_BIT);
+
+	tmp = SDRAM_TPC/ns;
+	if (tmp > 7) tmp = 7;
+	dmcr |= (tmp << EMC_DMCR_TPC_BIT);
+
+	tmp = SDRAM_TRWL/ns;
+	if (tmp > 3) tmp = 3;
+	dmcr |= (tmp << EMC_DMCR_TRWL_BIT);
+
+	tmp = (SDRAM_TRAS + SDRAM_TPC)/ns;
+	if (tmp > 14) tmp = 14;
+	dmcr |= (((tmp + 1) >> 1) << EMC_DMCR_TRC_BIT);
+#else
+	dmcr |= 0xfffc;
+#endif
+
+	/* First, precharge phase */
+	REG_EMC_DMCR = dmcr;
+
+	/* Set refresh registers */
+	tmp = SDRAM_TREF/ns;
+	tmp = tmp/64 + 1;
+	if (tmp > 0xff) tmp = 0xff;
+
+	REG_EMC_RTCOR = tmp;
+	REG_EMC_RTCSR = EMC_RTCSR_CKS_64;	/* Divisor is 64, CKO/64 */
+
+	/* SDRAM mode values */
+	sdmode = EMC_SDMR_BT_SEQ | 
+		 EMC_SDMR_OM_NORMAL |
+		 EMC_SDMR_BL_4 | 
+		 cas_latency_sdmr[((SDRAM_CASL == 3) ? 1 : 0)];
+
+	/* precharge all chip-selects */
+	REG8(EMC_SDMR0|sdmode) = 0;
+
+	/* wait for precharge, > 200us */
+	tmp = (cpu_clk / 1000000) * 200;
+	while (tmp--);
+
+	/* enable refresh and set SDRAM mode */
+	REG_EMC_DMCR = dmcr | EMC_DMCR_RFSH | EMC_DMCR_MRSET;
+
+	/* write sdram mode register for each chip-select */
+	REG8(EMC_SDMR0|sdmode) = 0;
+
+	/* everything is ok now */
+}
+
+void sdram_init(void)
+{
+	register unsigned int dmcr0, dmcr, sdmode, tmp, cpu_clk, mem_clk, ns;
+
+	unsigned int cas_latency_sdmr[2] = {
+		EMC_SDMR_CAS_2,
+		EMC_SDMR_CAS_3,
+	};
+
+	unsigned int cas_latency_dmcr[2] = {
+		1 << EMC_DMCR_TCL_BIT,	/* CAS latency is 2 */
+		2 << EMC_DMCR_TCL_BIT	/* CAS latency is 3 */
+	};
+
+	int div[] = {1, 2, 3, 4, 6, 8, 12, 16, 24, 32};
+
+	cpu_clk = CONFIG_SYS_CPU_SPEED;
+	mem_clk = cpu_clk * div[__cpm_get_cdiv()] / div[__cpm_get_mdiv()];
+
+	REG_EMC_BCR = 0;	/* Disable bus release */
+	REG_EMC_RTCSR = 0;	/* Disable clock for counting */
+
+	/* Fault DMCR value for mode register setting*/
+#define SDRAM_ROW0    11
+#define SDRAM_COL0     8
+#define SDRAM_BANK40   0
+
+	dmcr0 = ((SDRAM_ROW0-11)<<EMC_DMCR_RA_BIT) |
+		((SDRAM_COL0-8)<<EMC_DMCR_CA_BIT) |
+		(SDRAM_BANK40<<EMC_DMCR_BA_BIT) |
+		(SDRAM_BW16<<EMC_DMCR_BW_BIT) |
+		EMC_DMCR_EPIN |
+		cas_latency_dmcr[((SDRAM_CASL == 3) ? 1 : 0)];
+
+	/* Basic DMCR value */
+	dmcr = ((SDRAM_ROW-11)<<EMC_DMCR_RA_BIT) |
+		((SDRAM_COL-8)<<EMC_DMCR_CA_BIT) |
+		(SDRAM_BANK4<<EMC_DMCR_BA_BIT) |
+		(SDRAM_BW16<<EMC_DMCR_BW_BIT) |
+		EMC_DMCR_EPIN |
+		cas_latency_dmcr[((SDRAM_CASL == 3) ? 1 : 0)];
+
+	/* SDRAM timimg */
+	ns = 1000000000 / mem_clk;
+	tmp = SDRAM_TRAS/ns;
+	if (tmp < 4) tmp = 4;
+	if (tmp > 11) tmp = 11;
+	dmcr |= ((tmp-4) << EMC_DMCR_TRAS_BIT);
+	tmp = SDRAM_RCD/ns;
+	if (tmp > 3) tmp = 3;
+	dmcr |= (tmp << EMC_DMCR_RCD_BIT);
+	tmp = SDRAM_TPC/ns;
+	if (tmp > 7) tmp = 7;
+	dmcr |= (tmp << EMC_DMCR_TPC_BIT);
+	tmp = SDRAM_TRWL/ns;
+	if (tmp > 3) tmp = 3;
+	dmcr |= (tmp << EMC_DMCR_TRWL_BIT);
+	tmp = (SDRAM_TRAS + SDRAM_TPC)/ns;
+	if (tmp > 14) tmp = 14;
+	dmcr |= (((tmp + 1) >> 1) << EMC_DMCR_TRC_BIT);
+
+	/* SDRAM mode value */
+	sdmode = EMC_SDMR_BT_SEQ | 
+		 EMC_SDMR_OM_NORMAL |
+		 EMC_SDMR_BL_4 | 
+		 cas_latency_sdmr[((SDRAM_CASL == 3) ? 1 : 0)];
+
+	/* Stage 1. Precharge all banks by writing SDMR with DMCR.MRSET=0 */
+	REG_EMC_DMCR = dmcr;
+	REG8(EMC_SDMR0|sdmode) = 0;
+
+	/* Wait for precharge, > 200us */
+	tmp = (cpu_clk / 1000000) * 1000;
+	while (tmp--);
+
+	/* Stage 2. Enable auto-refresh */
+	REG_EMC_DMCR = dmcr | EMC_DMCR_RFSH;
+
+	tmp = SDRAM_TREF/ns;
+	tmp = tmp/64 + 1;
+	if (tmp > 0xff) tmp = 0xff;
+	REG_EMC_RTCOR = tmp;
+	REG_EMC_RTCNT = 0;
+	REG_EMC_RTCSR = EMC_RTCSR_CKS_64;	/* Divisor is 64, CKO/64 */
+
+	/* Wait for number of auto-refresh cycles */
+	tmp = (cpu_clk / 1000000) * 1000;
+	while (tmp--);
+
+ 	/* Stage 3. Mode Register Set */
+	REG_EMC_DMCR = dmcr0 | EMC_DMCR_RFSH | EMC_DMCR_MRSET;
+	REG8(EMC_SDMR0|sdmode) = 0;
+
+        /* Set back to basic DMCR value */
+	REG_EMC_DMCR = dmcr | EMC_DMCR_RFSH | EMC_DMCR_MRSET;
+
+	/* everything is ok now */
+}
+
+#ifndef CONFIG_NAND_SPL
+
+static void calc_clocks(void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	unsigned int pllout;
+	unsigned int div[10] = {1, 2, 3, 4, 6, 8, 12, 16, 24, 32};
+
+	pllout = __cpm_get_pllout();
+
+	gd->cpu_clk = pllout / div[__cpm_get_cdiv()];
+	gd->sys_clk = pllout / div[__cpm_get_hdiv()];
+	gd->per_clk = pllout / div[__cpm_get_pdiv()];
+	gd->mem_clk = pllout / div[__cpm_get_mdiv()];
+	gd->dev_clk = CONFIG_SYS_EXTAL;
+}
+
+static void rtc_init(void)
+{
+	unsigned long rtcsta;
+
+	while ( !__rtc_write_ready()) ;
+	__rtc_enable_alarm();	/* enable alarm */
+
+	while ( !__rtc_write_ready())
+		;
+	REG_RTC_RGR   = 0x00007fff; /* type value */
+
+	while ( !__rtc_write_ready())
+		;
+	REG_RTC_HWFCR = 0x0000ffe0; /* Power on delay 2s */
+
+	while ( !__rtc_write_ready())
+		;
+	REG_RTC_HRCR  = 0x00000fe0; /* reset delay 125ms */
+#if 0
+	while ( !__rtc_write_ready())
+		;
+	rtcsta = REG_RTC_HWRSR;
+	while ( !__rtc_write_ready())
+		;
+	if (rtcsta & 0x33) {
+		if (rtcsta & 0x10) {
+			while ( !__rtc_write_ready())
+				;
+			REG_RTC_RSR = 0x0;
+		}
+		while ( !__rtc_write_ready())
+			;
+		REG_RTC_HWRSR = 0x0;
+	}
+#endif
+}
+
+/*
+ * jz4740 board init routine
+ */
+int jz_board_init(void)
+{
+	board_early_init();  /* init gpio, pll etc. */
+#ifndef CONFIG_NAND_U_BOOT
+	pll_init();          /* init PLL */
+	sdram_init();        /* init sdram memory */
+#endif
+	calc_clocks();       /* calc the clocks */
+	rtc_init();		/* init rtc on any reset: */
+	return 0;
+}
+
+/* U-Boot common routines */
+phys_size_t initdram(int board_type)
+{
+	u32 dmcr;
+	u32 rows, cols, dw, banks;
+	ulong size;
+
+	dmcr = REG_EMC_DMCR;
+	rows = 11 + ((dmcr & EMC_DMCR_RA_MASK) >> EMC_DMCR_RA_BIT);
+	cols = 8 + ((dmcr & EMC_DMCR_CA_MASK) >> EMC_DMCR_CA_BIT);
+	dw = (dmcr & EMC_DMCR_BW) ? 2 : 4;
+	banks = (dmcr & EMC_DMCR_BA) ? 4 : 2;
+
+	size = (1 << (rows + cols)) * dw * banks;
+
+	return size;
+}
+
+/*
+ * Timer routines 
+ */
+
+#define TIMER_CHAN  0
+#define TIMER_FDATA 0xffff  /* Timer full data value */
+#define TIMER_HZ    CONFIG_SYS_HZ
+
+#define READ_TIMER  REG_TCU_TCNT(TIMER_CHAN)  /* macro to read the 16 bit timer */
+
+static ulong timestamp;
+static ulong lastdec;
+
+void	reset_timer_masked	(void);
+ulong	get_timer_masked	(void);
+void	udelay_masked		(unsigned long usec);
+
+/*
+ * timer without interrupts
+ */
+
+int timer_init(void)
+{
+	REG_TCU_TCSR(TIMER_CHAN) = TCU_TCSR_PRESCALE256 | TCU_TCSR_EXT_EN;
+	REG_TCU_TCNT(TIMER_CHAN) = 0;
+	REG_TCU_TDHR(TIMER_CHAN) = 0;
+	REG_TCU_TDFR(TIMER_CHAN) = TIMER_FDATA;
+
+	REG_TCU_TMSR = (1 << TIMER_CHAN) | (1 << (TIMER_CHAN + 16)); /* mask irqs */
+	REG_TCU_TSCR = (1 << TIMER_CHAN); /* enable timer clock */
+	REG_TCU_TESR = (1 << TIMER_CHAN); /* start counting up */
+
+	lastdec = 0;
+	timestamp = 0;
+
+	return 0;
+}
+
+void reset_timer(void)
+{
+	reset_timer_masked ();
+}
+
+ulong get_timer(ulong base)
+{
+	return get_timer_masked () - base;
+}
+
+void set_timer(ulong t)
+{
+	timestamp = t;
+}
+
+void udelay (unsigned long usec)
+{
+	ulong tmo,tmp;
+
+	/* normalize */
+	if (usec >= 1000) {
+		tmo = usec / 1000;
+		tmo *= TIMER_HZ;
+		tmo /= 1000;
+	}
+	else {
+		if (usec >= 1) {
+			tmo = usec * TIMER_HZ;
+			tmo /= (1000*1000);
+		}
+		else
+			tmo = 1;
+	}
+
+	/* check for rollover during this delay */
+	tmp = get_timer (0);
+	if ((tmp + tmo) < tmp )
+		reset_timer_masked();  /* timer would roll over */
+	else
+		tmo += tmp;
+
+	while (get_timer_masked () < tmo);
+}
+
+void reset_timer_masked (void)
+{
+	/* reset time */
+	lastdec = READ_TIMER;
+	timestamp = 0;
+}
+
+ulong get_timer_masked (void)
+{
+	ulong now = READ_TIMER;
+
+	if (lastdec <= now) {
+		/* normal mode */
+		timestamp += (now - lastdec);
+	} else {
+		/* we have an overflow ... */
+		timestamp += TIMER_FDATA + now - lastdec;
+	}
+	lastdec = now;
+
+	return timestamp;
+}
+
+void udelay_masked (unsigned long usec)
+{
+	ulong tmo;
+	ulong endtime;
+	signed long diff;
+
+	/* normalize */
+	if (usec >= 1000) {
+		tmo = usec / 1000;
+		tmo *= TIMER_HZ;
+		tmo /= 1000;
+	} else {
+		if (usec > 1) {
+			tmo = usec * TIMER_HZ;
+			tmo /= (1000*1000);
+		} else {
+			tmo = 1;
+		}
+	}
+
+	endtime = get_timer_masked () + tmo;
+
+	do {
+		ulong now = get_timer_masked ();
+		diff = endtime - now;
+	} while (diff >= 0);
+}
+
+/*
+ * This function is derived from PowerPC code (read timebase as long long).
+ * On MIPS it just returns the timer value.
+ */
+unsigned long long get_ticks(void)
+{
+	return get_timer(0);
+}
+
+/*
+ * This function is derived from PowerPC code (timebase clock frequency).
+ * On MIPS it returns the number of timer ticks per second.
+ */
+ulong get_tbclk (void)
+{
+	return TIMER_HZ;
+}
+
+#endif /* CONFIG_NAND_SPL */
+
+/* End of timer routine. */
+
+#endif

package/uboot-xburst/files/cpu/mips/jz4740_nand.c

@@ -0,0 +1,199 @@
+/*
+ * Platform independend driver for JZ4740.
+ *
+ * Copyright (c) 2007 Ingenic Semiconductor Inc.
+ * Author: <jlwei@ingenic.cn>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+#include <common.h>
+
+#if defined(CONFIG_CMD_NAND) && defined(CONFIG_JZ4740)
+
+#include <nand.h>
+#include <asm/jz4740.h>
+#include <asm/io.h>
+
+#define PAR_SIZE 9
+#define __nand_ecc_enable()    (REG_EMC_NFECR = EMC_NFECR_ECCE | EMC_NFECR_ERST )
+#define __nand_ecc_disable()   (REG_EMC_NFECR &= ~EMC_NFECR_ECCE)
+
+#define __nand_select_rs_ecc() (REG_EMC_NFECR |= EMC_NFECR_RS)
+
+#define __nand_rs_ecc_encoding()	(REG_EMC_NFECR |= EMC_NFECR_RS_ENCODING)
+#define __nand_rs_ecc_decoding()	(REG_EMC_NFECR |= EMC_NFECR_RS_DECODING)
+#define __nand_ecc_encode_sync() while (!(REG_EMC_NFINTS & EMC_NFINTS_ENCF))
+#define __nand_ecc_decode_sync() while (!(REG_EMC_NFINTS & EMC_NFINTS_DECF))
+
+static void jz_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
+{
+	struct nand_chip *this = mtd->priv;
+	unsigned long nandaddr = (unsigned long)this->IO_ADDR_W;
+
+	if (ctrl & NAND_CTRL_CHANGE) {
+		/* Change this to use I/O accessors. */
+		if (ctrl & NAND_NCE)
+			REG_EMC_NFCSR |= EMC_NFCSR_NFCE1; 
+		else
+			REG_EMC_NFCSR &= ~EMC_NFCSR_NFCE1;
+	}
+
+	if (cmd == NAND_CMD_NONE)
+		return;
+
+	if (ctrl & NAND_CLE)
+		nandaddr |= 0x00008000;
+	else /* must be ALE */
+		nandaddr |= 0x00010000;
+
+	writeb(cmd, (uint8_t *)nandaddr);
+}
+
+static int jz_device_ready(struct mtd_info *mtd)
+{
+	int ready;
+	udelay(20);	/* FIXME: add 20us delay */
+	ready = (REG_GPIO_PXPIN(2) & 0x40000000) ? 1 : 0;
+	return ready;
+}
+
+/*
+ * EMC setup
+ */
+static void jz_device_setup(void)
+{
+	/* Set NFE bit */
+	REG_EMC_NFCSR |= EMC_NFCSR_NFE1;
+	REG_EMC_SMCR1 = 0x094c4400;
+	/* REG_EMC_SMCR3 = 0x04444400; */
+}
+
+void board_nand_select_device(struct nand_chip *nand, int chip)
+{
+	/*
+	 * Don't use "chip" to address the NAND device,
+	 * generate the cs from the address where it is encoded.
+	 */
+}
+
+static int jzsoc_nand_calculate_rs_ecc(struct mtd_info* mtd, const u_char* dat,
+				u_char* ecc_code)
+{
+	volatile u8 *paraddr = (volatile u8 *)EMC_NFPAR0;
+	short i;
+
+	__nand_ecc_encode_sync()
+	__nand_ecc_disable();
+
+	for(i = 0; i < PAR_SIZE; i++)
+		ecc_code[i] = *paraddr++;
+
+	return 0;
+}
+
+static void jzsoc_nand_enable_rs_hwecc(struct mtd_info* mtd, int mode)
+{
+ 	__nand_ecc_enable();
+	__nand_select_rs_ecc();
+
+	REG_EMC_NFINTS = 0x0;
+	if (NAND_ECC_READ == mode){
+		__nand_rs_ecc_decoding();
+	}
+	if (NAND_ECC_WRITE == mode){
+		__nand_rs_ecc_encoding();
+	}
+}
+
+/* Correct 1~9-bit errors in 512-bytes data */
+static void jzsoc_rs_correct(unsigned char *dat, int idx, int mask)
+{
+	int i;
+
+	idx--;
+
+	i = idx + (idx >> 3);
+	if (i >= 512)
+		return;
+
+	mask <<= (idx & 0x7);
+
+	dat[i] ^= mask & 0xff;
+	if (i < 511)
+		dat[i+1] ^= (mask >> 8) & 0xff;
+}
+
+static int jzsoc_nand_rs_correct_data(struct mtd_info *mtd, u_char *dat,
+				 u_char *read_ecc, u_char *calc_ecc)
+{
+	volatile u8 *paraddr = (volatile u8 *)EMC_NFPAR0;
+	short k;
+	u32 stat;
+	/* Set PAR values */
+
+	for (k = 0; k < PAR_SIZE; k++) {
+		*paraddr++ = read_ecc[k];
+	}
+
+	/* Set PRDY */
+	REG_EMC_NFECR |= EMC_NFECR_PRDY;
+
+	/* Wait for completion */
+	__nand_ecc_decode_sync();
+	__nand_ecc_disable();
+
+	/* Check decoding */
+	stat = REG_EMC_NFINTS;
+	if (stat & EMC_NFINTS_ERR) {
+		if (stat & EMC_NFINTS_UNCOR) {
+			printk("Uncorrectable error occurred\n");
+			return -1;
+		}
+		else {
+			u32 errcnt = (stat & EMC_NFINTS_ERRCNT_MASK) >> EMC_NFINTS_ERRCNT_BIT;
+			switch (errcnt) {
+			case 4:
+				jzsoc_rs_correct(dat, (REG_EMC_NFERR3 & EMC_NFERR_INDEX_MASK) >> EMC_NFERR_INDEX_BIT, (REG_EMC_NFERR3 & EMC_NFERR_MASK_MASK) >> EMC_NFERR_MASK_BIT);
+			case 3:
+				jzsoc_rs_correct(dat, (REG_EMC_NFERR2 & EMC_NFERR_INDEX_MASK) >> EMC_NFERR_INDEX_BIT, (REG_EMC_NFERR2 & EMC_NFERR_MASK_MASK) >> EMC_NFERR_MASK_BIT);
+			case 2:
+				jzsoc_rs_correct(dat, (REG_EMC_NFERR1 & EMC_NFERR_INDEX_MASK) >> EMC_NFERR_INDEX_BIT, (REG_EMC_NFERR1 & EMC_NFERR_MASK_MASK) >> EMC_NFERR_MASK_BIT);
+			case 1:
+				jzsoc_rs_correct(dat, (REG_EMC_NFERR0 & EMC_NFERR_INDEX_MASK) >> EMC_NFERR_INDEX_BIT, (REG_EMC_NFERR0 & EMC_NFERR_MASK_MASK) >> EMC_NFERR_MASK_BIT);
+				return 0;
+			default:
+				break;
+	   		}
+		}
+	}
+	/* no error need to be correct */
+	return 0;
+}
+
+/*
+ * Main initialization routine
+ */
+int board_nand_init(struct nand_chip *nand)
+{
+	jz_device_setup();
+
+	nand->cmd_ctrl =  jz_hwcontrol;
+	nand->dev_ready = jz_device_ready;
+
+	/* FIXME: should use NAND_ECC_SOFT */
+	nand->ecc.hwctl = jzsoc_nand_enable_rs_hwecc;
+	nand->ecc.correct = jzsoc_nand_rs_correct_data;
+	nand->ecc.calculate = jzsoc_nand_calculate_rs_ecc;
+	nand->ecc.mode = NAND_ECC_HW;
+	nand->ecc.size = 512;
+	nand->ecc.bytes = 9;
+
+	/* 20 us command delay time */
+	nand->chip_delay = 20;
+
+	return 0;
+}
+#endif /* (CONFIG_SYS_CMD_NAND) */

package/uboot-xburst/files/cpu/mips/jz_lcd.c

@@ -0,0 +1,484 @@
+/*
+ * JzRISC lcd controller
+ *
+ * xiangfu liu <xiangfu.z@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * Fallowing macro may be used:
+ *  CONFIG_LCD                        : LCD support
+ *  LCD_BPP                           : Bits per pixel, 0 = 1, 1 = 2, 2 = 4, 3 = 8
+ *  CONFIG_LCD_LOGO                   : show logo
+ */
+
+#include <config.h>
+#include <common.h>
+#include <lcd.h>
+
+#include <asm/io.h>               /* virt_to_phys() */
+
+#if defined(CONFIG_LCD) && !defined(CONFIG_SLCD)
+
+#if defined(CONFIG_JZ4740)
+#include <asm/jz4740.h>
+#endif
+
+#include "jz_lcd.h"
+
+
+struct jzfb_info {
+	unsigned int cfg;	/* panel mode and pin usage etc. */
+	unsigned int w;
+	unsigned int h;
+	unsigned int bpp;	/* bit per pixel */
+	unsigned int fclk;	/* frame clk */
+	unsigned int hsw;	/* hsync width, in pclk */
+	unsigned int vsw;	/* vsync width, in line count */
+	unsigned int elw;	/* end of line, in pclk */
+	unsigned int blw;	/* begin of line, in pclk */
+	unsigned int efw;	/* end of frame, in line count */
+	unsigned int bfw;	/* begin of frame, in line count */
+};
+
+static struct jzfb_info jzfb = {
+   #if defined(CONFIG_NANONOTE)
+	MODE_8BIT_SERIAL_TFT | PCLK_N | HSYNC_N | VSYNC_N,
+	320, 240, 32, 70, 1, 1, 273, 140, 1, 20
+   #endif
+
+};
+
+/************************************************************************/
+
+vidinfo_t panel_info = {
+#if defined(CONFIG_JZLCD_FOXCONN_PT035TN01)
+	320, 240, LCD_BPP,
+#endif
+};
+
+/*----------------------------------------------------------------------*/
+
+int lcd_line_length;
+
+int lcd_color_fg;
+int lcd_color_bg;
+
+/*
+ * Frame buffer memory information
+ */
+void *lcd_base;			/* Start of framebuffer memory	*/
+void *lcd_console_address;	/* Start of console buffer	*/
+
+short console_col;
+short console_row;
+
+/*----------------------------------------------------------------------*/
+
+void lcd_ctrl_init (void *lcdbase);
+
+void lcd_enable (void);
+void lcd_disable (void);
+
+/*----------------------------------------------------------------------*/
+
+static int  jz_lcd_init_mem(void *lcdbase, vidinfo_t *vid);
+static void jz_lcd_desc_init(vidinfo_t *vid);
+static int  jz_lcd_hw_init( vidinfo_t *vid );
+extern int flush_cache_all(void);
+
+#if LCD_BPP == LCD_COLOR8
+void lcd_setcolreg (ushort regno, ushort red, ushort green, ushort blue);
+#endif
+#if LCD_BPP == LCD_MONOCHROME
+void lcd_initcolregs (void);
+#endif
+
+/*-----------------------------------------------------------------------*/
+
+void lcd_ctrl_init (void *lcdbase)
+{
+	__lcd_display_pin_init();
+
+	jz_lcd_init_mem(lcdbase, &panel_info);
+	jz_lcd_desc_init(&panel_info);
+	jz_lcd_hw_init(&panel_info);
+
+	__lcd_display_on() ;
+}
+
+/*----------------------------------------------------------------------*/
+#if LCD_BPP == LCD_COLOR8
+void
+lcd_setcolreg (ushort regno, ushort red, ushort green, ushort blue)
+{
+}
+#endif
+/*----------------------------------------------------------------------*/
+
+#if LCD_BPP == LCD_MONOCHROME
+static
+void lcd_initcolregs (void)
+{
+}
+#endif
+
+/*
+ * Before enabled lcd controller, lcd registers should be configured correctly.
+ */
+
+void lcd_enable (void)
+{
+	REG_LCD_CTRL &= ~(1<<4); /* LCDCTRL.DIS */
+	REG_LCD_CTRL |= 1<<3;    /* LCDCTRL.ENA*/
+}
+
+void lcd_disable (void)
+{
+	REG_LCD_CTRL |= (1<<4); /* LCDCTRL.DIS, regular disable */
+	/* REG_LCD_CTRL |= (1<<3); */  /* LCDCTRL.DIS, quikly disable */
+}
+
+static int jz_lcd_init_mem(void *lcdbase, vidinfo_t *vid)
+{
+	u_long palette_mem_size;
+	struct jz_fb_info *fbi = &vid->jz_fb;
+	int fb_size = vid->vl_row * (vid->vl_col * NBITS (vid->vl_bpix)) / 8;
+
+	fbi->screen = (u_long)lcdbase;
+	fbi->palette_size = 256;
+	palette_mem_size = fbi->palette_size * sizeof(u16);
+
+	debug("jz_lcd.c palette_mem_size = 0x%08lx\n", (u_long) palette_mem_size);
+	/* locate palette and descs at end of page following fb */
+	fbi->palette = (u_long)lcdbase + fb_size + PAGE_SIZE - palette_mem_size;
+
+	return 0;
+}
+
+static void jz_lcd_desc_init(vidinfo_t *vid)
+{
+	struct jz_fb_info * fbi;
+	fbi = &vid->jz_fb;
+	fbi->dmadesc_fblow = (struct jz_fb_dma_descriptor *)((unsigned int)fbi->palette - 3*16);
+	fbi->dmadesc_fbhigh = (struct jz_fb_dma_descriptor *)((unsigned int)fbi->palette - 2*16);
+	fbi->dmadesc_palette = (struct jz_fb_dma_descriptor *)((unsigned int)fbi->palette - 1*16);
+
+	#define BYTES_PER_PANEL	 (vid->vl_col * vid->vl_row * NBITS(vid->vl_bpix) / 8)
+
+	/* populate descriptors */
+	fbi->dmadesc_fblow->fdadr = virt_to_phys(fbi->dmadesc_fblow);
+	fbi->dmadesc_fblow->fsadr = virt_to_phys((void *)(fbi->screen + BYTES_PER_PANEL));
+	fbi->dmadesc_fblow->fidr  = 0;
+	fbi->dmadesc_fblow->ldcmd = BYTES_PER_PANEL / 4 ;
+
+	fbi->fdadr1 = virt_to_phys(fbi->dmadesc_fblow); /* only used in dual-panel mode */
+
+	fbi->dmadesc_fbhigh->fsadr = virt_to_phys((void *)fbi->screen); 
+	fbi->dmadesc_fbhigh->fidr = 0;
+	fbi->dmadesc_fbhigh->ldcmd =  BYTES_PER_PANEL / 4; /* length in word */
+
+	fbi->dmadesc_palette->fsadr = virt_to_phys((void *)fbi->palette);
+	fbi->dmadesc_palette->fidr  = 0;
+	fbi->dmadesc_palette->ldcmd = (fbi->palette_size * 2)/4 | (1<<28);
+
+	if( NBITS(vid->vl_bpix) < 12)
+	{
+		/* assume any mode with <12 bpp is palette driven */
+		fbi->dmadesc_palette->fdadr = virt_to_phys(fbi->dmadesc_fbhigh);
+		fbi->dmadesc_fbhigh->fdadr = virt_to_phys(fbi->dmadesc_palette);
+		/* flips back and forth between pal and fbhigh */
+		fbi->fdadr0 = virt_to_phys(fbi->dmadesc_palette);
+	} else {
+		/* palette shouldn't be loaded in true-color mode */
+		fbi->dmadesc_fbhigh->fdadr = virt_to_phys((void *)fbi->dmadesc_fbhigh);
+		fbi->fdadr0 = virt_to_phys(fbi->dmadesc_fbhigh); /* no pal just fbhigh */
+	}
+
+	flush_cache_all();
+}
+
+static int  jz_lcd_hw_init(vidinfo_t *vid)
+{
+	struct jz_fb_info *fbi = &vid->jz_fb;
+	unsigned int val = 0;
+	unsigned int pclk;
+	unsigned int stnH;
+#if defined(CONFIG_MIPS_JZ4740)
+	int pll_div;
+#endif
+
+	/* Setting Control register */
+	switch (jzfb.bpp) {
+	case 1:
+		val |= LCD_CTRL_BPP_1;
+		break;
+	case 2:
+		val |= LCD_CTRL_BPP_2;
+		break;
+	case 4:
+		val |= LCD_CTRL_BPP_4;
+		break;
+	case 8:
+		val |= LCD_CTRL_BPP_8;
+		break;
+	case 15:
+		val |= LCD_CTRL_RGB555;
+	case 16:
+		val |= LCD_CTRL_BPP_16;
+		break;
+#if defined(CONFIG_MIPS_JZ4740)
+	case 17 ... 32:
+		val |= LCD_CTRL_BPP_18_24;	/* target is 4bytes/pixel */
+		break;
+#endif
+	default:
+		printf("jz_lcd.c The BPP %d is not supported\n", jzfb.bpp);
+		val |= LCD_CTRL_BPP_16;
+		break;
+	}
+
+	switch (jzfb.cfg & MODE_MASK) {
+	case MODE_STN_MONO_DUAL:
+	case MODE_STN_COLOR_DUAL:
+	case MODE_STN_MONO_SINGLE:
+	case MODE_STN_COLOR_SINGLE:
+		switch (jzfb.bpp) {
+		case 1:
+			/* val |= LCD_CTRL_PEDN; */
+		case 2:
+			val |= LCD_CTRL_FRC_2;
+			break;
+		case 4:
+			val |= LCD_CTRL_FRC_4;
+			break;
+		case 8:
+		default:
+			val |= LCD_CTRL_FRC_16;
+			break;
+		}
+		break;
+	}
+
+	val |= LCD_CTRL_BST_16;		/* Burst Length is 16WORD=64Byte */
+	val |= LCD_CTRL_OFUP;		/* OutFIFO underrun protect */
+
+	switch (jzfb.cfg & MODE_MASK) {
+	case MODE_STN_MONO_DUAL:
+	case MODE_STN_COLOR_DUAL:
+	case MODE_STN_MONO_SINGLE:
+	case MODE_STN_COLOR_SINGLE:
+		switch (jzfb.cfg & STN_DAT_PINMASK) {
+#define align2(n) (n)=((((n)+1)>>1)<<1)
+#define align4(n) (n)=((((n)+3)>>2)<<2)
+#define align8(n) (n)=((((n)+7)>>3)<<3)
+		case STN_DAT_PIN1:
+			/* Do not adjust the hori-param value. */
+			break;
+		case STN_DAT_PIN2:
+			align2(jzfb.hsw);
+			align2(jzfb.elw);
+			align2(jzfb.blw);
+			break;
+		case STN_DAT_PIN4:
+			align4(jzfb.hsw);
+			align4(jzfb.elw);
+			align4(jzfb.blw);
+			break;
+		case STN_DAT_PIN8:
+			align8(jzfb.hsw);
+			align8(jzfb.elw);
+			align8(jzfb.blw);
+			break;
+		}
+		break;
+	}
+
+	REG_LCD_CTRL = val;
+
+	switch (jzfb.cfg & MODE_MASK) {
+	case MODE_STN_MONO_DUAL:
+	case MODE_STN_COLOR_DUAL:
+	case MODE_STN_MONO_SINGLE:
+	case MODE_STN_COLOR_SINGLE:
+		if (((jzfb.cfg & MODE_MASK) == MODE_STN_MONO_DUAL) ||
+		    ((jzfb.cfg & MODE_MASK) == MODE_STN_COLOR_DUAL))
+			stnH = jzfb.h >> 1;
+		else
+			stnH = jzfb.h;
+
+		REG_LCD_VSYNC = (0 << 16) | jzfb.vsw;
+		REG_LCD_HSYNC = ((jzfb.blw+jzfb.w) << 16) | (jzfb.blw+jzfb.w+jzfb.hsw);
+
+		/* Screen setting */
+		REG_LCD_VAT = ((jzfb.blw + jzfb.w + jzfb.hsw + jzfb.elw) << 16) | (stnH + jzfb.vsw + jzfb.bfw + jzfb.efw);
+		REG_LCD_DAH = (jzfb.blw << 16) | (jzfb.blw + jzfb.w);
+		REG_LCD_DAV = (0 << 16) | (stnH);
+
+		/* AC BIAs signal */
+		REG_LCD_PS = (0 << 16) | (stnH+jzfb.vsw+jzfb.efw+jzfb.bfw);
+
+		break;
+
+	case MODE_TFT_GEN:
+	case MODE_TFT_SHARP:
+	case MODE_TFT_CASIO:
+	case MODE_TFT_SAMSUNG:
+	case MODE_8BIT_SERIAL_TFT:
+	case MODE_TFT_18BIT:
+		REG_LCD_VSYNC = (0 << 16) | jzfb.vsw;
+		REG_LCD_HSYNC = (0 << 16) | jzfb.hsw;
+#if defined(CONFIG_JZLCD_INNOLUX_AT080TN42)
+		REG_LCD_DAV = (0 << 16) | ( jzfb.h );
+#else
+		REG_LCD_DAV =((jzfb.vsw+jzfb.bfw) << 16) | (jzfb.vsw +jzfb.bfw+jzfb.h);
+#endif /*#if defined(CONFIG_JZLCD_INNOLUX_AT080TN42)*/
+		REG_LCD_DAH = ((jzfb.hsw + jzfb.blw) << 16) | (jzfb.hsw + jzfb.blw + jzfb.w );
+		REG_LCD_VAT = (((jzfb.blw + jzfb.w + jzfb.elw + jzfb.hsw)) << 16) \
+			| (jzfb.vsw + jzfb.bfw + jzfb.h + jzfb.efw);
+		break;
+	}
+
+	switch (jzfb.cfg & MODE_MASK) {
+	case MODE_TFT_SAMSUNG:
+	{
+		unsigned int total, tp_s, tp_e, ckv_s, ckv_e;
+		unsigned int rev_s, rev_e, inv_s, inv_e;
+
+		pclk = val * (jzfb.w + jzfb.hsw + jzfb.elw + jzfb.blw) *
+			(jzfb.h + jzfb.vsw + jzfb.efw + jzfb.bfw); /* Pixclk */
+
+		total = jzfb.blw + jzfb.w + jzfb.elw + jzfb.hsw;
+		tp_s = jzfb.blw + jzfb.w + 1;
+		tp_e = tp_s + 1;
+		/* ckv_s = tp_s - jz_clocks.pixclk/(1000000000/4100); */
+		ckv_s = tp_s - pclk/(1000000000/4100);
+		ckv_e = tp_s + total;
+		rev_s = tp_s - 11;	/* -11.5 clk */
+		rev_e = rev_s + total;
+		inv_s = tp_s;
+		inv_e = inv_s + total;
+		REG_LCD_CLS = (tp_s << 16) | tp_e;
+		REG_LCD_PS = (ckv_s << 16) | ckv_e;
+		REG_LCD_SPL = (rev_s << 16) | rev_e;
+		REG_LCD_REV = (inv_s << 16) | inv_e;
+		jzfb.cfg |= STFT_REVHI | STFT_SPLHI;
+		break;
+	}
+	case MODE_TFT_SHARP:
+	{
+		unsigned int total, cls_s, cls_e, ps_s, ps_e;
+		unsigned int spl_s, spl_e, rev_s, rev_e;
+		total = jzfb.blw + jzfb.w + jzfb.elw + jzfb.hsw;
+#if !defined(CONFIG_JZLCD_INNOLUX_AT080TN42)
+		spl_s = 1;
+		spl_e = spl_s + 1;
+		cls_s = 0;
+		cls_e = total - 60;	/* > 4us (pclk = 80ns) */
+		ps_s = cls_s;
+		ps_e = cls_e;
+		rev_s = total - 40;	/* > 3us (pclk = 80ns) */
+		rev_e = rev_s + total;
+		jzfb.cfg |= STFT_PSHI; 
+#else           /*#if defined(CONFIG_JZLCD_INNOLUX_AT080TN42)*/
+		spl_s = total - 5; /* LD */
+		spl_e = total -3;
+		cls_s = 32;	/* CKV */
+		cls_e = 145;
+		ps_s  = 0;      /* OEV */
+		ps_e  = 45;
+		rev_s = 0;	/* POL */
+		rev_e = 0;
+#endif          /*#if defined(CONFIG_JZLCD_INNOLUX_AT080TN42)*/
+		REG_LCD_SPL = (spl_s << 16) | spl_e;
+		REG_LCD_CLS = (cls_s << 16) | cls_e;
+		REG_LCD_PS = (ps_s << 16) | ps_e;
+		REG_LCD_REV = (rev_s << 16) | rev_e;
+		break;
+	}
+	case MODE_TFT_CASIO:
+		break;
+	}
+
+	/* Configure the LCD panel */
+	REG_LCD_CFG = jzfb.cfg;
+
+	/* Timing setting */
+	__cpm_stop_lcd();
+
+	val = jzfb.fclk; /* frame clk */
+	if ( (jzfb.cfg & MODE_MASK) != MODE_8BIT_SERIAL_TFT) {
+		pclk = val * (jzfb.w + jzfb.hsw + jzfb.elw + jzfb.blw) *
+			(jzfb.h + jzfb.vsw + jzfb.efw + jzfb.bfw); /* Pixclk */
+	}
+	else {
+		/* serial mode: Hsync period = 3*Width_Pixel */
+		pclk = val * (jzfb.w*3 + jzfb.hsw + jzfb.elw + jzfb.blw) *
+			(jzfb.h + jzfb.vsw + jzfb.efw + jzfb.bfw); /* Pixclk */
+	}
+
+	if (((jzfb.cfg & MODE_MASK) == MODE_STN_COLOR_SINGLE) ||
+	    ((jzfb.cfg & MODE_MASK) == MODE_STN_COLOR_DUAL))
+		pclk = (pclk * 3);
+
+	if (((jzfb.cfg & MODE_MASK) == MODE_STN_COLOR_SINGLE) ||
+	    ((jzfb.cfg & MODE_MASK) == MODE_STN_COLOR_DUAL) ||
+	    ((jzfb.cfg & MODE_MASK) == MODE_STN_MONO_SINGLE) ||
+	    ((jzfb.cfg & MODE_MASK) == MODE_STN_MONO_DUAL))
+		pclk = pclk >> ((jzfb.cfg & STN_DAT_PINMASK) >> 4);
+
+	if (((jzfb.cfg & MODE_MASK) == MODE_STN_COLOR_DUAL) ||
+	    ((jzfb.cfg & MODE_MASK) == MODE_STN_MONO_DUAL))
+		pclk >>= 1;
+
+	pll_div = ( REG_CPM_CPCCR & CPM_CPCCR_PCS ); /* clock source,0:pllout/2 1: pllout */
+	pll_div = pll_div ? 1 : 2 ;
+	val = ( __cpm_get_pllout()/pll_div ) / pclk;
+	val--;
+	if ( val > 0x1ff ) {
+		printf("CPM_LPCDR too large, set it to 0x1ff\n");
+		val = 0x1ff;
+	}
+	__cpm_set_pixdiv(val);
+
+	val = pclk * 3 ;	/* LCDClock > 2.5*Pixclock */
+	if ( val > 150000000 ) {
+		printf("Warning: LCDClock=%d\n, LCDClock must less or equal to 150MHz.\n", val);
+		printf("Change LCDClock to 150MHz\n");
+		val = 150000000;
+	}
+	val = ( __cpm_get_pllout()/pll_div ) / val;
+	val--;
+	if ( val > 0x1f ) {
+		printf("CPM_CPCCR.LDIV too large, set it to 0x1f\n");
+		val = 0x1f;
+	}
+	__cpm_set_ldiv( val );
+	REG_CPM_CPCCR |= CPM_CPCCR_CE ; /* update divide */
+
+	__cpm_start_lcd();
+	udelay(1000);
+
+	REG_LCD_DA0 = fbi->fdadr0; /* frame descripter*/
+
+	if (((jzfb.cfg & MODE_MASK) == MODE_STN_COLOR_DUAL) ||
+	    ((jzfb.cfg & MODE_MASK) == MODE_STN_MONO_DUAL))
+		REG_LCD_DA1 = fbi->fdadr1; /* frame descripter*/
+
+	return 0;
+}
+

package/uboot-xburst/files/cpu/mips/jz_lcd.h

@@ -0,0 +1,260 @@
+/*
+ * JzRISC lcd controller
+ *
+ * xiangfu liu <xiangfu.z@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __JZLCD_H__
+#define __JZLCD_H__
+
+#include <asm/io.h>
+/*
+ * change u-boot macro to celinux macro
+ */
+/* Chip type */
+#if defined(CONFIG_JZ4740)
+#define CONFIG_MIPS_JZ4740 		1
+#endif
+
+/* board type */
+#if defined(CONFIG_NANONOTE)
+#define CONFIG_MIPS_JZ4740_PI 		1
+#endif
+
+#define mdelay(n) 		udelay((n)*1000)
+
+/*
+ * change u-boot macro to celinux macro
+ */
+
+#define NR_PALETTE	256
+
+struct lcd_desc{
+	unsigned int next_desc; /* LCDDAx */
+	unsigned int databuf;   /* LCDSAx */
+	unsigned int frame_id;  /* LCDFIDx */
+	unsigned int cmd;       /* LCDCMDx */
+};
+
+#define MODE_MASK		0x0f
+#define MODE_TFT_GEN		0x00
+#define MODE_TFT_SHARP		0x01
+#define MODE_TFT_CASIO		0x02
+#define MODE_TFT_SAMSUNG	0x03
+#define MODE_CCIR656_NONINT	0x04
+#define MODE_CCIR656_INT	0x05
+#define MODE_STN_COLOR_SINGLE	0x08
+#define MODE_STN_MONO_SINGLE	0x09
+#define MODE_STN_COLOR_DUAL	0x0a
+#define MODE_STN_MONO_DUAL	0x0b
+#define MODE_8BIT_SERIAL_TFT    0x0c
+
+#define MODE_TFT_18BIT          (1<<7)
+
+#define STN_DAT_PIN1	(0x00 << 4)
+#define STN_DAT_PIN2	(0x01 << 4)
+#define STN_DAT_PIN4	(0x02 << 4)
+#define STN_DAT_PIN8	(0x03 << 4)
+#define STN_DAT_PINMASK	STN_DAT_PIN8
+
+#define STFT_PSHI	(1 << 15)
+#define STFT_CLSHI	(1 << 14)
+#define STFT_SPLHI	(1 << 13)
+#define STFT_REVHI	(1 << 12)
+
+#define SYNC_MASTER	(0 << 16)
+#define SYNC_SLAVE	(1 << 16)
+
+#define DE_P		(0 << 9)
+#define DE_N		(1 << 9)
+
+#define PCLK_P		(0 << 10)
+#define PCLK_N		(1 << 10)
+
+#define HSYNC_P		(0 << 11)
+#define HSYNC_N		(1 << 11)
+
+#define VSYNC_P		(0 << 8)
+#define VSYNC_N		(1 << 8)
+
+#define DATA_NORMAL	(0 << 17)
+#define DATA_INVERSE	(1 << 17)
+
+
+/* Jz LCDFB supported I/O controls. */
+#define FBIOSETBACKLIGHT	0x4688
+#define FBIODISPON		0x4689
+#define FBIODISPOFF		0x468a
+#define FBIORESET		0x468b
+#define FBIOPRINT_REG		0x468c
+
+/*
+ * LCD panel specific definition
+ */
+
+#if defined(CONFIG_JZLCD_FOXCONN_PT035TN01) || defined(CONFIG_JZLCD_INNOLUX_PT035TN01_SERIAL)
+
+#if defined(CONFIG_JZLCD_FOXCONN_PT035TN01) /* board pmp */
+#define MODE 0xcd 		/* 24bit parellel RGB */
+#endif
+#if defined(CONFIG_JZLCD_INNOLUX_PT035TN01_SERIAL)
+#define MODE 0xc9		/* 8bit serial RGB */
+#endif
+
+#if defined(CONFIG_MIPS_JZ4740_PI) /* board pavo */
+	#define SPEN	(32*2+21)       /*LCD_SPL */
+	#define SPCK	(32*2+23)       /*LCD_CLS */
+	#define SPDA	(32*2+22)       /*LCD_D12 */
+	#define LCD_RET (32*3+27) 
+#else
+#error "cpu/misp/Jzlcd.h, please define SPI pins on your board."
+#endif
+
+	#define __spi_write_reg1(reg, val) \
+	do { \
+		unsigned char no;\
+		unsigned short value;\
+		unsigned char a=0;\
+		unsigned char b=0;\
+		a=reg;\
+		b=val;\
+		__gpio_set_pin(SPEN);\
+		__gpio_set_pin(SPCK);\
+		__gpio_clear_pin(SPDA);\
+		__gpio_clear_pin(SPEN);\
+		udelay(25);\
+		value=((a<<8)|(b&0xFF));\
+		for(no=0;no<16;no++)\
+		{\
+			__gpio_clear_pin(SPCK);\
+			if((value&0x8000)==0x8000)\
+			__gpio_set_pin(SPDA);\
+			else\
+			__gpio_clear_pin(SPDA);\
+			udelay(25);\
+			__gpio_set_pin(SPCK);\
+			value=(value<<1); \
+			udelay(25);\
+		 }\
+		__gpio_set_pin(SPEN);\
+		udelay(100);\
+	} while (0)
+
+	#define __spi_write_reg(reg, val) \
+	do {\
+		__spi_write_reg1((reg<<2|2), val);\
+		udelay(100); \
+	}while(0)
+
+	
+	#define __lcd_special_pin_init() \
+	do { \
+		__gpio_as_output(SPEN); /* use SPDA */\
+		__gpio_as_output(SPCK); /* use SPCK */\
+		__gpio_as_output(SPDA); /* use SPDA */\
+		__gpio_as_output(LCD_RET);\
+	} while (0)
+
+#if defined(CONFIG_NANONOTE)
+	#define __lcd_special_on() \
+		do { \
+		udelay(50);\
+		__spi_write_reg1(0x05, 0x16); \
+		__spi_write_reg1(0x04, 0x0b); \
+		__spi_write_reg1(0x07, 0x8d); \
+		__spi_write_reg1(0x01, 0x95); \
+		__spi_write_reg1(0x08, 0xc0); \
+		__spi_write_reg1(0x03, 0x40); \
+		__spi_write_reg1(0x06, 0x15); \
+		__spi_write_reg1(0x05, 0xd7); \
+		} while (0)	/* reg 0x0a is control the display direction:DB0->horizontal level DB1->vertical level */
+
+	#define __lcd_special_off()				\
+			  do {					\
+				  __spi_write_reg1(0x05, 0x5e);	\
+			  } while (0)
+#endif	/* CONFIG_NANONOTE */
+#endif	/* CONFIG_JZLCD_FOXCONN_PT035TN01 or CONFIG_JZLCD_INNOLUX_PT035TN01_SERIAL */
+
+#ifndef __lcd_special_pin_init
+#define __lcd_special_pin_init()
+#endif
+#ifndef __lcd_special_on
+#define __lcd_special_on()
+#endif
+#ifndef __lcd_special_off
+#define __lcd_special_off()
+#endif
+
+
+/*
+ * Platform specific definition
+ */
+
+#if defined(CONFIG_MIPS_JZ4740_PI)
+
+	/* 100 level: 0,1,...,100 */
+	#define __lcd_set_backlight_level(n)\
+	do { \
+	__gpio_as_output(32*3+27); \
+	__gpio_set_pin(32*3+27); \
+	} while (0)
+
+	#define __lcd_close_backlight() \
+	do { \
+	__gpio_as_output(GPIO_PWM); \
+	__gpio_clear_pin(GPIO_PWM); \
+	} while (0)
+
+	#define __lcd_display_pin_init() \
+	do { \
+		__gpio_as_output(GPIO_DISP_OFF_N); \
+		__cpm_start_tcu(); \
+		__lcd_special_pin_init(); \
+	} while (0)
+	/*	__lcd_set_backlight_level(100); \*/
+	#define __lcd_display_on() \
+	do { \
+		__gpio_set_pin(GPIO_DISP_OFF_N); \
+		__lcd_special_on(); \
+	} while (0)
+
+	#define __lcd_display_off() \
+	do { \
+		__lcd_special_off(); \
+		__gpio_clear_pin(GPIO_DISP_OFF_N); \
+	} while (0)
+
+#endif /* CONFIG_MIPS_JZ4740_PI) */
+
+/*****************************************************************************
+ * LCD display pin dummy macros
+ *****************************************************************************/
+#ifndef __lcd_display_pin_init
+#define __lcd_display_pin_init()
+#endif
+#ifndef __lcd_display_on
+#define __lcd_display_on()
+#endif
+#ifndef __lcd_display_off
+#define __lcd_display_off()
+#endif
+#ifndef __lcd_set_backlight_level
+#define __lcd_set_backlight_level(n)
+#endif
+

package/uboot-xburst/files/cpu/mips/jz_mmc.h

@@ -0,0 +1,113 @@
+/*
+ *  linux/drivers/mmc/jz_mmc.h
+ *
+ *  Author: Vladimir Shebordaev, Igor Oblakov
+ *  Copyright:  MontaVista Software Inc.
+ *
+ *  $Id: jz_mmc.h,v 1.3 2007-06-15 08:04:20 jlwei Exp $
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License version 2 as
+ *  published by the Free Software Foundation.
+ */
+#ifndef __MMC_JZMMC_H__
+#define __MMC_JZMMC_H__
+
+#include "mmc_protocol.h"
+
+#define MMC_DEBUG_LEVEL		0		/* Enable Debug: 0 - no debug */
+
+#define MMC_BLOCK_SIZE		512		/* MMC/SD Block Size */
+
+#define ID_TO_RCA(x) ((x)+1)
+
+#define MMC_OCR_ARG		0x00ff8000	/* Argument of OCR */
+
+enum mmc_result_t {
+	MMC_NO_RESPONSE        = -1,
+	MMC_NO_ERROR           = 0,
+	MMC_ERROR_OUT_OF_RANGE,
+	MMC_ERROR_ADDRESS,
+	MMC_ERROR_BLOCK_LEN,
+	MMC_ERROR_ERASE_SEQ,
+	MMC_ERROR_ERASE_PARAM,
+	MMC_ERROR_WP_VIOLATION,
+	MMC_ERROR_CARD_IS_LOCKED,
+	MMC_ERROR_LOCK_UNLOCK_FAILED,
+	MMC_ERROR_COM_CRC,
+	MMC_ERROR_ILLEGAL_COMMAND,
+	MMC_ERROR_CARD_ECC_FAILED,
+	MMC_ERROR_CC,
+	MMC_ERROR_GENERAL,
+	MMC_ERROR_UNDERRUN,
+	MMC_ERROR_OVERRUN,
+	MMC_ERROR_CID_CSD_OVERWRITE,
+	MMC_ERROR_STATE_MISMATCH,
+	MMC_ERROR_HEADER_MISMATCH,
+	MMC_ERROR_TIMEOUT,
+	MMC_ERROR_CRC,
+	MMC_ERROR_DRIVER_FAILURE,
+};
+
+/* the information structure of MMC/SD Card */
+typedef struct MMC_INFO
+{
+	int             id;     /* Card index */
+        int             sd;     /* MMC or SD card */
+        int             rca;    /* RCA */
+        u32             scr;    /* SCR 63:32*/
+	int             flags;  /* Ejected, inserted */
+	enum card_state state;  /* empty, ident, ready, whatever */
+
+	/* Card specific information */
+	struct mmc_cid  cid;
+	struct mmc_csd  csd;
+	u32             block_num;
+	u32             block_len;
+	u32             erase_unit;
+} mmc_info;
+
+mmc_info mmcinfo;
+
+struct mmc_request {
+	int               index;      /* Slot index - used for CS lines */
+	int               cmd;        /* Command to send */
+	u32               arg;        /* Argument to send */
+	enum mmc_rsp_t    rtype;      /* Response type expected */
+
+	/* Data transfer (these may be modified at the low level) */
+	u16               nob;        /* Number of blocks to transfer*/
+	u16               block_len;  /* Block length */
+	u8               *buffer;     /* Data buffer */
+	u32               cnt;        /* Data length, for PIO */
+
+	/* Results */
+	u8                response[18]; /* Buffer to store response - CRC is optional */
+	enum mmc_result_t result;
+};
+
+char * mmc_result_to_string(int);
+int    mmc_unpack_csd(struct mmc_request *request, struct mmc_csd *csd);
+int    mmc_unpack_r1(struct mmc_request *request, struct mmc_response_r1 *r1, enum card_state state);
+int    mmc_unpack_r6(struct mmc_request *request, struct mmc_response_r1 *r1, enum card_state state, int *rca);
+int    mmc_unpack_scr(struct mmc_request *request, struct mmc_response_r1 *r1, enum card_state state, u32 *scr);
+int    mmc_unpack_cid(struct mmc_request *request, struct mmc_cid *cid);
+int    mmc_unpack_r3(struct mmc_request *request, struct mmc_response_r3 *r3);
+
+void   mmc_send_cmd(struct mmc_request *request, int cmd, u32 arg, 
+		     u16 nob, u16 block_len, enum mmc_rsp_t rtype, u8 *buffer);
+u32    mmc_tran_speed(u8 ts);
+void   jz_mmc_set_clock(int sd, u32 rate);
+void   jz_mmc_hardware_init(void);
+
+static inline void mmc_simple_cmd(struct mmc_request *request, int cmd, u32 arg, enum mmc_rsp_t rtype)
+{
+	mmc_send_cmd( request, cmd, arg, 0, 0, rtype, 0);
+}
+
+int mmc_legacy_init(int verbose);
+int mmc_read(ulong src, uchar *dst, int size);
+int mmc_write(uchar *src, ulong dst, int size);
+int mmc2info(ulong addr);
+
+#endif /* __MMC_JZMMC_H__ */

package/uboot-xburst/files/cpu/mips/jz_serial.c

@@ -0,0 +1,141 @@
+/*
+ * Jz47xx UART support
+ *
+ * Hardcoded to UART 0 for now
+ * Options also hardcoded to 8N1
+ *
+ *  Copyright (c) 2005
+ *  Ingenic Semiconductor, <jlwei@ingenic.cn>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+
+#if defined(CONFIG_JZ4740)
+
+#include <common.h>
+
+#include <asm/jz4740.h>
+
+#undef UART_BASE
+#ifndef CONFIG_SYS_UART_BASE
+#define UART_BASE  UART0_BASE
+#else
+#define UART_BASE  CONFIG_SYS_UART_BASE
+#endif
+
+/******************************************************************************
+*
+* serial_init - initialize a channel
+*
+* This routine initializes the number of data bits, parity
+* and set the selected baud rate. Interrupts are disabled.
+* Set the modem control signals if the option is selected.
+*
+* RETURNS: N/A
+*/
+
+int serial_init (void)
+{
+#if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
+	volatile u8 *uart_fcr = (volatile u8 *)(UART_BASE + OFF_FCR);
+	volatile u8 *uart_lcr = (volatile u8 *)(UART_BASE + OFF_LCR);
+	volatile u8 *uart_ier = (volatile u8 *)(UART_BASE + OFF_IER);
+	volatile u8 *uart_sircr = (volatile u8 *)(UART_BASE + OFF_SIRCR);
+
+	/* Disable port interrupts while changing hardware */
+	*uart_ier = 0;
+
+	/* Disable UART unit function */
+	*uart_fcr = ~UART_FCR_UUE;
+
+	/* Set both receiver and transmitter in UART mode (not SIR) */
+	*uart_sircr = ~(SIRCR_RSIRE | SIRCR_TSIRE);
+
+	/* Set databits, stopbits and parity. (8-bit data, 1 stopbit, no parity) */
+	*uart_lcr = UART_LCR_WLEN_8 | UART_LCR_STOP_1;
+
+	/* Set baud rate */
+	serial_setbrg();
+
+	/* Enable UART unit, enable and clear FIFO */
+	*uart_fcr = UART_FCR_UUE | UART_FCR_FE | UART_FCR_TFLS | UART_FCR_RFLS;
+#endif
+	return 0;
+}
+
+void serial_setbrg (void)
+{
+	volatile u8 *uart_lcr = (volatile u8 *)(UART_BASE + OFF_LCR);
+	volatile u8 *uart_dlhr = (volatile u8 *)(UART_BASE + OFF_DLHR);
+	volatile u8 *uart_dllr = (volatile u8 *)(UART_BASE + OFF_DLLR);
+	u32 baud_div, tmp;
+
+	baud_div = CONFIG_SYS_EXTAL / 16 / CONFIG_BAUDRATE;
+
+	tmp = *uart_lcr;
+	tmp |= UART_LCR_DLAB;
+	*uart_lcr = tmp;
+
+	*uart_dlhr = (baud_div >> 8) & 0xff;
+	*uart_dllr = baud_div & 0xff;
+
+	tmp &= ~UART_LCR_DLAB;
+	*uart_lcr = tmp;
+}
+
+void serial_putc (const char c)
+{
+	volatile u8 *uart_lsr = (volatile u8 *)(UART_BASE + OFF_LSR);
+	volatile u8 *uart_tdr = (volatile u8 *)(UART_BASE + OFF_TDR);
+
+	if (c == '\n') serial_putc ('\r');
+
+	/* Wait for fifo to shift out some bytes */
+	while ( !((*uart_lsr & (UART_LSR_TDRQ | UART_LSR_TEMT)) == 0x60) );
+
+	*uart_tdr = (u8)c;
+}
+
+void serial_puts (const char *s)
+{
+	while (*s) {
+		serial_putc (*s++);
+	}
+}
+
+int serial_getc (void)
+{
+	volatile u8 *uart_rdr = (volatile u8 *)(UART_BASE + OFF_RDR);
+
+	while (!serial_tstc());
+
+	return *uart_rdr;
+}
+
+int serial_tstc (void)
+{
+	volatile u8 *uart_lsr = (volatile u8 *)(UART_BASE + OFF_LSR);
+
+	if (*uart_lsr & UART_LSR_DR) {
+		/* Data in rfifo */
+		return (1);
+	}
+	return 0;
+}
+
+#endif

package/uboot-xburst/files/cpu/mips/mmc_protocol.h

@@ -0,0 +1,273 @@
+/*
+**********************************************************************
+*
+*                            uC/MMC
+*
+*             (c) Copyright 2005 - 2007, Ingenic Semiconductor, Inc
+*                      All rights reserved.
+*
+***********************************************************************
+
+----------------------------------------------------------------------
+File        : mmc_protocol.h
+Purpose     : MMC protocol definitions.
+
+----------------------------------------------------------------------
+Version-Date-----Author-Explanation
+----------------------------------------------------------------------
+1.00.00 20060831 WeiJianli     First release
+
+----------------------------------------------------------------------
+Known problems or limitations with current version
+----------------------------------------------------------------------
+(none)
+---------------------------END-OF-HEADER------------------------------
+*/
+
+#ifndef __MMC_PROTOCOL__
+#define __MMC_PROTOCOL__
+
+/* Standard MMC/SD clock speeds */
+#define MMC_CLOCK_SLOW    400000      /* 400 kHz for initial setup */
+#define MMC_CLOCK_FAST  20000000      /* 20 MHz for maximum for normal operation */
+#define SD_CLOCK_FAST   24000000      /* 24 MHz for SD Cards */
+ 
+/* Extra MMC commands for state control */
+/* Use negative numbers to disambiguate */
+#define MMC_CIM_RESET            -1
+
+/* Standard MMC commands (3.1)           type  argument     response */
+   /* class 1 */
+#define	MMC_GO_IDLE_STATE         0   /* bc                          */
+#define MMC_SEND_OP_COND          1   /* bcr  [31:0] OCR         R3  */
+#define MMC_ALL_SEND_CID          2   /* bcr                     R2  */
+#define MMC_SET_RELATIVE_ADDR     3   /* ac   [31:16] RCA        R1  */
+#define MMC_SET_DSR               4   /* bc   [31:16] RCA            */
+#define MMC_SELECT_CARD           7   /* ac   [31:16] RCA        R1  */
+#define MMC_SEND_CSD              9   /* ac   [31:16] RCA        R2  */
+#define MMC_SEND_CID             10   /* ac   [31:16] RCA        R2  */
+#define MMC_READ_DAT_UNTIL_STOP  11   /* adtc [31:0] dadr        R1  */
+#define MMC_STOP_TRANSMISSION    12   /* ac                      R1b */
+#define MMC_SEND_STATUS	         13   /* ac   [31:16] RCA        R1  */
+#define MMC_GO_INACTIVE_STATE    15   /* ac   [31:16] RCA            */
+
+  /* class 2 */
+#define MMC_SET_BLOCKLEN         16   /* ac   [31:0] block len   R1  */
+#define MMC_READ_SINGLE_BLOCK    17   /* adtc [31:0] data addr   R1  */
+#define MMC_READ_MULTIPLE_BLOCK  18   /* adtc [31:0] data addr   R1  */
+
+  /* class 3 */
+#define MMC_WRITE_DAT_UNTIL_STOP 20   /* adtc [31:0] data addr   R1  */
+
+  /* class 4 */
+#define MMC_SET_BLOCK_COUNT      23   /* adtc [31:0] data addr   R1  */
+#define MMC_WRITE_BLOCK          24   /* adtc [31:0] data addr   R1  */
+#define MMC_WRITE_MULTIPLE_BLOCK 25   /* adtc                    R1  */
+#define MMC_PROGRAM_CID          26   /* adtc                    R1  */
+#define MMC_PROGRAM_CSD          27   /* adtc                    R1  */
+
+  /* class 6 */
+#define MMC_SET_WRITE_PROT       28   /* ac   [31:0] data addr   R1b */
+#define MMC_CLR_WRITE_PROT       29   /* ac   [31:0] data addr   R1b */
+#define MMC_SEND_WRITE_PROT      30   /* adtc [31:0] wpdata addr R1  */
+
+  /* class 5 */
+#define MMC_ERASE_GROUP_START    35   /* ac   [31:0] data addr   R1  */
+#define MMC_ERASE_GROUP_END      36   /* ac   [31:0] data addr   R1  */
+#define MMC_ERASE                37   /* ac                      R1b */
+
+  /* class 9 */
+#define MMC_FAST_IO              39   /* ac   <Complex>          R4  */
+#define MMC_GO_IRQ_STATE         40   /* bcr                     R5  */
+
+  /* class 7 */
+#define MMC_LOCK_UNLOCK          42   /* adtc                    R1b */
+
+  /* class 8 */
+#define MMC_APP_CMD              55   /* ac   [31:16] RCA        R1  */
+#define MMC_GEN_CMD              56   /* adtc [0] RD/WR          R1b */
+
+  /* SD class */
+#define SD_SEND_OP_COND          41   /* bcr  [31:0] OCR         R3  */
+#define SET_BUS_WIDTH            6    /* ac   [1:0] bus width    R1  */
+#define SEND_SCR                 51   /* adtc [31:0] staff       R1  */
+
+/* Don't change the order of these; they are used in dispatch tables */
+enum mmc_rsp_t {
+	RESPONSE_NONE   = 0,
+	RESPONSE_R1     = 1,
+	RESPONSE_R1B    = 2,
+	RESPONSE_R2_CID = 3,
+	RESPONSE_R2_CSD  = 4,
+	RESPONSE_R3      = 5,
+	RESPONSE_R4      = 6,
+	RESPONSE_R5      = 7,
+        RESPONSE_R6      = 8,
+};
+
+
+/*
+  MMC status in R1
+  Type
+  	e : error bit
+	s : status bit
+	r : detected and set for the actual command response
+	x : detected and set during command execution. the host must poll
+            the card by sending status command in order to read these bits.
+  Clear condition
+  	a : according to the card state
+	b : always related to the previous command. Reception of
+            a valid command will clear it (with a delay of one command)
+	c : clear by read
+ */
+
+#define R1_OUT_OF_RANGE		(1 << 31)	/* er, c */
+#define R1_ADDRESS_ERROR	(1 << 30)	/* erx, c */
+#define R1_BLOCK_LEN_ERROR	(1 << 29)	/* er, c */
+#define R1_ERASE_SEQ_ERROR      (1 << 28)	/* er, c */
+#define R1_ERASE_PARAM		(1 << 27)	/* ex, c */
+#define R1_WP_VIOLATION		(1 << 26)	/* erx, c */
+#define R1_CARD_IS_LOCKED	(1 << 25)	/* sx, a */
+#define R1_LOCK_UNLOCK_FAILED	(1 << 24)	/* erx, c */
+#define R1_COM_CRC_ERROR	(1 << 23)	/* er, b */
+#define R1_ILLEGAL_COMMAND	(1 << 22)	/* er, b */
+#define R1_CARD_ECC_FAILED	(1 << 21)	/* ex, c */
+#define R1_CC_ERROR		(1 << 20)	/* erx, c */
+#define R1_ERROR		(1 << 19)	/* erx, c */
+#define R1_UNDERRUN		(1 << 18)	/* ex, c */
+#define R1_OVERRUN		(1 << 17)	/* ex, c */
+#define R1_CID_CSD_OVERWRITE	(1 << 16)	/* erx, c, CID/CSD overwrite */
+#define R1_WP_ERASE_SKIP	(1 << 15)	/* sx, c */
+#define R1_CARD_ECC_DISABLED	(1 << 14)	/* sx, a */
+#define R1_ERASE_RESET		(1 << 13)	/* sr, c */
+#define R1_STATUS(x)            (x & 0xFFFFE000)
+#define R1_CURRENT_STATE(x)    	((x & 0x00001E00) >> 9)	/* sx, b (4 bits) */
+#define R1_READY_FOR_DATA	(1 << 8)	/* sx, a */
+#define R1_APP_CMD		(1 << 7)	/* sr, c */
+
+enum card_state {
+	CARD_STATE_EMPTY = -1,
+	CARD_STATE_IDLE	 = 0,
+	CARD_STATE_READY = 1,
+	CARD_STATE_IDENT = 2,
+	CARD_STATE_STBY	 = 3,
+	CARD_STATE_TRAN	 = 4,
+	CARD_STATE_DATA	 = 5,
+	CARD_STATE_RCV	 = 6,
+	CARD_STATE_PRG	 = 7,
+	CARD_STATE_DIS	 = 8,
+};
+
+/* These are unpacked versions of the actual responses */
+
+ struct mmc_response_r1 {
+	u8  cmd;
+	u32 status;
+};
+
+typedef struct mmc_cid {
+	u8  mid;
+	u16 oid;
+	u8  pnm[7];   /* Product name (we null-terminate) */
+	u8  prv;
+	u32 psn;
+	u8  mdt;
+}mmc_cid_t;
+
+typedef struct mmc_csd {
+	u8  csd_structure;
+	u8  spec_vers;
+	u8  taac;
+	u8  nsac;
+	u8  tran_speed;
+	u16 ccc;
+	u8  read_bl_len;
+	u8  read_bl_partial;
+	u8  write_blk_misalign;
+	u8  read_blk_misalign;
+	u8  dsr_imp;
+	u16 c_size;
+	u8  vdd_r_curr_min;
+	u8  vdd_r_curr_max;
+	u8  vdd_w_curr_min;
+	u8  vdd_w_curr_max;
+	u8  c_size_mult;
+	union {
+		struct { /* MMC system specification version 3.1 */
+			u8  erase_grp_size;
+			u8  erase_grp_mult;
+		} v31;
+		struct { /* MMC system specification version 2.2 */
+			u8  sector_size;
+			u8  erase_grp_size;
+		} v22;
+	} erase;
+	u8  wp_grp_size;
+	u8  wp_grp_enable;
+	u8  default_ecc;
+	u8  r2w_factor;
+	u8  write_bl_len;
+	u8  write_bl_partial;
+	u8  file_format_grp;
+	u8  copy;
+	u8  perm_write_protect;
+	u8  tmp_write_protect;
+	u8  file_format;
+	u8  ecc;
+}mmc_csd_t;;
+
+struct mmc_response_r3 {
+	u32 ocr;
+};
+
+#define MMC_VDD_145_150	0x00000001	/* VDD voltage 1.45 - 1.50 */
+#define MMC_VDD_150_155	0x00000002	/* VDD voltage 1.50 - 1.55 */
+#define MMC_VDD_155_160	0x00000004	/* VDD voltage 1.55 - 1.60 */
+#define MMC_VDD_160_165	0x00000008	/* VDD voltage 1.60 - 1.65 */
+#define MMC_VDD_165_170	0x00000010	/* VDD voltage 1.65 - 1.70 */
+#define MMC_VDD_17_18	0x00000020	/* VDD voltage 1.7 - 1.8 */
+#define MMC_VDD_18_19	0x00000040	/* VDD voltage 1.8 - 1.9 */
+#define MMC_VDD_19_20	0x00000080	/* VDD voltage 1.9 - 2.0 */
+#define MMC_VDD_20_21	0x00000100	/* VDD voltage 2.0 ~ 2.1 */
+#define MMC_VDD_21_22	0x00000200	/* VDD voltage 2.1 ~ 2.2 */
+#define MMC_VDD_22_23	0x00000400	/* VDD voltage 2.2 ~ 2.3 */
+#define MMC_VDD_23_24	0x00000800	/* VDD voltage 2.3 ~ 2.4 */
+#define MMC_VDD_24_25	0x00001000	/* VDD voltage 2.4 ~ 2.5 */
+#define MMC_VDD_25_26	0x00002000	/* VDD voltage 2.5 ~ 2.6 */
+#define MMC_VDD_26_27	0x00004000	/* VDD voltage 2.6 ~ 2.7 */
+#define MMC_VDD_27_28	0x00008000	/* VDD voltage 2.7 ~ 2.8 */
+#define MMC_VDD_28_29	0x00010000	/* VDD voltage 2.8 ~ 2.9 */
+#define MMC_VDD_29_30	0x00020000	/* VDD voltage 2.9 ~ 3.0 */
+#define MMC_VDD_30_31	0x00040000	/* VDD voltage 3.0 ~ 3.1 */
+#define MMC_VDD_31_32	0x00080000	/* VDD voltage 3.1 ~ 3.2 */
+#define MMC_VDD_32_33	0x00100000	/* VDD voltage 3.2 ~ 3.3 */
+#define MMC_VDD_33_34	0x00200000	/* VDD voltage 3.3 ~ 3.4 */
+#define MMC_VDD_34_35	0x00400000	/* VDD voltage 3.4 ~ 3.5 */
+#define MMC_VDD_35_36	0x00800000	/* VDD voltage 3.5 ~ 3.6 */
+#define MMC_CARD_BUSY	0x80000000	/* Card Power up status bit */
+
+
+/* CSD field definitions */
+
+#define CSD_STRUCT_VER_1_0  0           /* Valid for system specification 1.0 - 1.2 */
+#define CSD_STRUCT_VER_1_1  1           /* Valid for system specification 1.4 - 2.2 */
+#define CSD_STRUCT_VER_1_2  2           /* Valid for system specification 3.1       */
+
+#define CSD_SPEC_VER_0      0           /* Implements system specification 1.0 - 1.2 */
+#define CSD_SPEC_VER_1      1           /* Implements system specification 1.4 */
+#define CSD_SPEC_VER_2      2           /* Implements system specification 2.0 - 2.2 */
+#define CSD_SPEC_VER_3      3           /* Implements system specification 3.1 */
+
+#if MMC_DEBUG_LEVEL
+
+#define DEBUG(n, args...)			\
+    do {    \
+	if (n <=  MMC_DEBUG_LEVEL) {	\
+		printf(args);	\
+	}    \
+    } while(0)
+#else
+#define DEBUG(n, args...)
+#endif /* MMC_DEBUG_EN */
+
+#endif  /* __MMC_PROTOCOL__ */

package/uboot-xburst/files/cpu/mips/nanonote_gpm940b0.c

@@ -0,0 +1,420 @@
+/*
+ * JzRISC lcd controller
+ *
+ * xiangfu liu <xiangfu.z@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <common.h>
+#include <lcd.h>
+
+#include <asm/io.h>               /* virt_to_phys() */
+
+#include <asm/jz4740.h>
+#include "nanonote_gpm940b0.h"
+
+#define align2(n) (n)=((((n)+1)>>1)<<1)
+#define align4(n) (n)=((((n)+3)>>2)<<2)
+#define align8(n) (n)=((((n)+7)>>3)<<3)
+
+struct jzfb_info {
+	unsigned int cfg;	/* panel mode and pin usage etc. */
+	unsigned int w;
+	unsigned int h;
+	unsigned int bpp;	/* bit per pixel */
+	unsigned int fclk;	/* frame clk */
+	unsigned int hsw;	/* hsync width, in pclk */
+	unsigned int vsw;	/* vsync width, in line count */
+	unsigned int elw;	/* end of line, in pclk */
+	unsigned int blw;	/* begin of line, in pclk */
+	unsigned int efw;	/* end of frame, in line count */
+	unsigned int bfw;	/* begin of frame, in line count */
+};
+
+static struct jzfb_info jzfb = {
+	MODE_8BIT_SERIAL_TFT | PCLK_N | HSYNC_N | VSYNC_N,
+	320, 240, 32, 70, 1, 1, 273, 140, 1, 20
+};
+
+vidinfo_t panel_info = {
+	320, 240, LCD_BPP,
+};
+
+int lcd_line_length;
+
+int lcd_color_fg;
+int lcd_color_bg;
+/*
+ * Frame buffer memory information
+ */
+void *lcd_base;			/* Start of framebuffer memory	*/
+void *lcd_console_address;	/* Start of console buffer	*/
+
+short console_col;
+short console_row;
+
+void lcd_ctrl_init (void *lcdbase);
+void lcd_enable (void);
+void lcd_disable (void);
+
+static int  jz_lcd_init_mem(void *lcdbase, vidinfo_t *vid);
+static void jz_lcd_desc_init(vidinfo_t *vid);
+static int  jz_lcd_hw_init( vidinfo_t *vid );
+extern int flush_cache_all(void);
+
+void lcd_ctrl_init (void *lcdbase)
+{
+	__lcd_display_pin_init();
+
+	jz_lcd_init_mem(lcdbase, &panel_info);
+	jz_lcd_desc_init(&panel_info);
+	jz_lcd_hw_init(&panel_info);
+
+	__lcd_display_on() ;
+}
+
+/*
+ * Before enabled lcd controller, lcd registers should be configured correctly.
+ */
+
+void lcd_enable (void)
+{
+	REG_LCD_CTRL &= ~(1<<4); /* LCDCTRL.DIS */
+	REG_LCD_CTRL |= 1<<3;    /* LCDCTRL.ENA*/
+}
+
+void lcd_disable (void)
+{
+	REG_LCD_CTRL |= (1<<4); /* LCDCTRL.DIS, regular disable */
+	/* REG_LCD_CTRL |= (1<<3); */  /* LCDCTRL.DIS, quikly disable */
+}
+
+static int jz_lcd_init_mem(void *lcdbase, vidinfo_t *vid)
+{
+	u_long palette_mem_size;
+	struct jz_fb_info *fbi = &vid->jz_fb;
+	int fb_size = vid->vl_row * (vid->vl_col * NBITS (vid->vl_bpix)) / 8;
+
+	fbi->screen = (u_long)lcdbase;
+	fbi->palette_size = 256;
+	palette_mem_size = fbi->palette_size * sizeof(u16);
+
+	debug("jz_lcd.c palette_mem_size = 0x%08lx\n", (u_long) palette_mem_size);
+	/* locate palette and descs at end of page following fb */
+	fbi->palette = (u_long)lcdbase + fb_size + PAGE_SIZE - palette_mem_size;
+
+	return 0;
+}
+
+static void jz_lcd_desc_init(vidinfo_t *vid)
+{
+	struct jz_fb_info * fbi;
+	fbi = &vid->jz_fb;
+	fbi->dmadesc_fblow = (struct jz_fb_dma_descriptor *)((unsigned int)fbi->palette - 3*16);
+	fbi->dmadesc_fbhigh = (struct jz_fb_dma_descriptor *)((unsigned int)fbi->palette - 2*16);
+	fbi->dmadesc_palette = (struct jz_fb_dma_descriptor *)((unsigned int)fbi->palette - 1*16);
+
+	#define BYTES_PER_PANEL	 (vid->vl_col * vid->vl_row * NBITS(vid->vl_bpix) / 8)
+
+	/* populate descriptors */
+	fbi->dmadesc_fblow->fdadr = virt_to_phys(fbi->dmadesc_fblow);
+	fbi->dmadesc_fblow->fsadr = virt_to_phys((void *)(fbi->screen + BYTES_PER_PANEL));
+	fbi->dmadesc_fblow->fidr  = 0;
+	fbi->dmadesc_fblow->ldcmd = BYTES_PER_PANEL / 4 ;
+
+	fbi->fdadr1 = virt_to_phys(fbi->dmadesc_fblow); /* only used in dual-panel mode */
+
+	fbi->dmadesc_fbhigh->fsadr = virt_to_phys((void *)fbi->screen);
+	fbi->dmadesc_fbhigh->fidr = 0;
+	fbi->dmadesc_fbhigh->ldcmd =  BYTES_PER_PANEL / 4; /* length in word */
+
+	fbi->dmadesc_palette->fsadr = virt_to_phys((void *)fbi->palette);
+	fbi->dmadesc_palette->fidr  = 0;
+	fbi->dmadesc_palette->ldcmd = (fbi->palette_size * 2)/4 | (1<<28);
+
+	if(NBITS(vid->vl_bpix) < 12)
+	{
+		/* assume any mode with <12 bpp is palette driven */
+		fbi->dmadesc_palette->fdadr = virt_to_phys(fbi->dmadesc_fbhigh);
+		fbi->dmadesc_fbhigh->fdadr = virt_to_phys(fbi->dmadesc_palette);
+		/* flips back and forth between pal and fbhigh */
+		fbi->fdadr0 = virt_to_phys(fbi->dmadesc_palette);
+	} else {
+		/* palette shouldn't be loaded in true-color mode */
+		fbi->dmadesc_fbhigh->fdadr = virt_to_phys((void *)fbi->dmadesc_fbhigh);
+		fbi->fdadr0 = virt_to_phys(fbi->dmadesc_fbhigh); /* no pal just fbhigh */
+	}
+
+	flush_cache_all();
+}
+
+static int  jz_lcd_hw_init(vidinfo_t *vid)
+{
+	struct jz_fb_info *fbi = &vid->jz_fb;
+	unsigned int val = 0;
+	unsigned int pclk;
+	unsigned int stnH;
+	int pll_div;
+
+	/* Setting Control register */
+	switch (jzfb.bpp) {
+	case 1:
+		val |= LCD_CTRL_BPP_1;
+		break;
+	case 2:
+		val |= LCD_CTRL_BPP_2;
+		break;
+	case 4:
+		val |= LCD_CTRL_BPP_4;
+		break;
+	case 8:
+		val |= LCD_CTRL_BPP_8;
+		break;
+	case 15:
+		val |= LCD_CTRL_RGB555;
+	case 16:
+		val |= LCD_CTRL_BPP_16;
+		break;
+	case 17 ... 32:
+		val |= LCD_CTRL_BPP_18_24;	/* target is 4bytes/pixel */
+		break;
+
+	default:
+		printf("jz_lcd.c The BPP %d is not supported\n", jzfb.bpp);
+		val |= LCD_CTRL_BPP_16;
+		break;
+	}
+
+	switch (jzfb.cfg & MODE_MASK) {
+	case MODE_STN_MONO_DUAL:
+	case MODE_STN_COLOR_DUAL:
+	case MODE_STN_MONO_SINGLE:
+	case MODE_STN_COLOR_SINGLE:
+		switch (jzfb.bpp) {
+		case 1:
+			/* val |= LCD_CTRL_PEDN; */
+		case 2:
+			val |= LCD_CTRL_FRC_2;
+			break;
+		case 4:
+			val |= LCD_CTRL_FRC_4;
+			break;
+		case 8:
+		default:
+			val |= LCD_CTRL_FRC_16;
+			break;
+		}
+		break;
+	}
+
+	val |= LCD_CTRL_BST_16;		/* Burst Length is 16WORD=64Byte */
+	val |= LCD_CTRL_OFUP;		/* OutFIFO underrun protect */
+
+	switch (jzfb.cfg & MODE_MASK) {
+	case MODE_STN_MONO_DUAL:
+	case MODE_STN_COLOR_DUAL:
+	case MODE_STN_MONO_SINGLE:
+	case MODE_STN_COLOR_SINGLE:
+		switch (jzfb.cfg & STN_DAT_PINMASK) {
+		case STN_DAT_PIN1:
+			/* Do not adjust the hori-param value. */
+			break;
+		case STN_DAT_PIN2:
+			align2(jzfb.hsw);
+			align2(jzfb.elw);
+			align2(jzfb.blw);
+			break;
+		case STN_DAT_PIN4:
+			align4(jzfb.hsw);
+			align4(jzfb.elw);
+			align4(jzfb.blw);
+			break;
+		case STN_DAT_PIN8:
+			align8(jzfb.hsw);
+			align8(jzfb.elw);
+			align8(jzfb.blw);
+			break;
+		}
+		break;
+	}
+
+	REG_LCD_CTRL = val;
+
+	switch (jzfb.cfg & MODE_MASK) {
+	case MODE_STN_MONO_DUAL:
+	case MODE_STN_COLOR_DUAL:
+	case MODE_STN_MONO_SINGLE:
+	case MODE_STN_COLOR_SINGLE:
+		if (((jzfb.cfg & MODE_MASK) == MODE_STN_MONO_DUAL) ||
+		    ((jzfb.cfg & MODE_MASK) == MODE_STN_COLOR_DUAL))
+			stnH = jzfb.h >> 1;
+		else
+			stnH = jzfb.h;
+
+		REG_LCD_VSYNC = (0 << 16) | jzfb.vsw;
+		REG_LCD_HSYNC = ((jzfb.blw+jzfb.w) << 16) | (jzfb.blw+jzfb.w+jzfb.hsw);
+
+		/* Screen setting */
+		REG_LCD_VAT = ((jzfb.blw + jzfb.w + jzfb.hsw + jzfb.elw) << 16) | (stnH + jzfb.vsw + jzfb.bfw + jzfb.efw);
+		REG_LCD_DAH = (jzfb.blw << 16) | (jzfb.blw + jzfb.w);
+		REG_LCD_DAV = (0 << 16) | (stnH);
+
+		/* AC BIAs signal */
+		REG_LCD_PS = (0 << 16) | (stnH+jzfb.vsw+jzfb.efw+jzfb.bfw);
+
+		break;
+
+	case MODE_TFT_GEN:
+	case MODE_TFT_SHARP:
+	case MODE_TFT_CASIO:
+	case MODE_TFT_SAMSUNG:
+	case MODE_8BIT_SERIAL_TFT:
+	case MODE_TFT_18BIT:
+		REG_LCD_VSYNC = (0 << 16) | jzfb.vsw;
+		REG_LCD_HSYNC = (0 << 16) | jzfb.hsw;
+		REG_LCD_DAV =((jzfb.vsw+jzfb.bfw) << 16) | (jzfb.vsw +jzfb.bfw+jzfb.h);
+		REG_LCD_DAH = ((jzfb.hsw + jzfb.blw) << 16) | (jzfb.hsw + jzfb.blw + jzfb.w );
+		REG_LCD_VAT = (((jzfb.blw + jzfb.w + jzfb.elw + jzfb.hsw)) << 16) \
+			| (jzfb.vsw + jzfb.bfw + jzfb.h + jzfb.efw);
+		break;
+	}
+
+	switch (jzfb.cfg & MODE_MASK) {
+	case MODE_TFT_SAMSUNG:
+	{
+		unsigned int total, tp_s, tp_e, ckv_s, ckv_e;
+		unsigned int rev_s, rev_e, inv_s, inv_e;
+
+		pclk = val * (jzfb.w + jzfb.hsw + jzfb.elw + jzfb.blw) *
+			(jzfb.h + jzfb.vsw + jzfb.efw + jzfb.bfw); /* Pixclk */
+
+		total = jzfb.blw + jzfb.w + jzfb.elw + jzfb.hsw;
+		tp_s = jzfb.blw + jzfb.w + 1;
+		tp_e = tp_s + 1;
+		/* ckv_s = tp_s - jz_clocks.pixclk/(1000000000/4100); */
+		ckv_s = tp_s - pclk/(1000000000/4100);
+		ckv_e = tp_s + total;
+		rev_s = tp_s - 11;	/* -11.5 clk */
+		rev_e = rev_s + total;
+		inv_s = tp_s;
+		inv_e = inv_s + total;
+		REG_LCD_CLS = (tp_s << 16) | tp_e;
+		REG_LCD_PS = (ckv_s << 16) | ckv_e;
+		REG_LCD_SPL = (rev_s << 16) | rev_e;
+		REG_LCD_REV = (inv_s << 16) | inv_e;
+		jzfb.cfg |= STFT_REVHI | STFT_SPLHI;
+		break;
+	}
+	case MODE_TFT_SHARP:
+	{
+		unsigned int total, cls_s, cls_e, ps_s, ps_e;
+		unsigned int spl_s, spl_e, rev_s, rev_e;
+		total = jzfb.blw + jzfb.w + jzfb.elw + jzfb.hsw;
+		spl_s = 1;
+		spl_e = spl_s + 1;
+		cls_s = 0;
+		cls_e = total - 60;	/* > 4us (pclk = 80ns) */
+		ps_s = cls_s;
+		ps_e = cls_e;
+		rev_s = total - 40;	/* > 3us (pclk = 80ns) */
+		rev_e = rev_s + total;
+		jzfb.cfg |= STFT_PSHI; 
+		REG_LCD_SPL = (spl_s << 16) | spl_e;
+		REG_LCD_CLS = (cls_s << 16) | cls_e;
+		REG_LCD_PS = (ps_s << 16) | ps_e;
+		REG_LCD_REV = (rev_s << 16) | rev_e;
+		break;
+	}
+	case MODE_TFT_CASIO:
+		break;
+	}
+
+	/* Configure the LCD panel */
+	REG_LCD_CFG = jzfb.cfg;
+
+	/* Timing setting */
+	__cpm_stop_lcd();
+
+	val = jzfb.fclk; /* frame clk */
+	if ( (jzfb.cfg & MODE_MASK) != MODE_8BIT_SERIAL_TFT) {
+		pclk = val * (jzfb.w + jzfb.hsw + jzfb.elw + jzfb.blw) *
+			(jzfb.h + jzfb.vsw + jzfb.efw + jzfb.bfw); /* Pixclk */
+	} else {
+		/* serial mode: Hsync period = 3*Width_Pixel */
+		pclk = val * (jzfb.w*3 + jzfb.hsw + jzfb.elw + jzfb.blw) *
+			(jzfb.h + jzfb.vsw + jzfb.efw + jzfb.bfw); /* Pixclk */
+	}
+
+	if (((jzfb.cfg & MODE_MASK) == MODE_STN_COLOR_SINGLE) ||
+	    ((jzfb.cfg & MODE_MASK) == MODE_STN_COLOR_DUAL))
+		pclk = (pclk * 3);
+
+	if (((jzfb.cfg & MODE_MASK) == MODE_STN_COLOR_SINGLE) ||
+	    ((jzfb.cfg & MODE_MASK) == MODE_STN_COLOR_DUAL) ||
+	    ((jzfb.cfg & MODE_MASK) == MODE_STN_MONO_SINGLE) ||
+	    ((jzfb.cfg & MODE_MASK) == MODE_STN_MONO_DUAL))
+		pclk = pclk >> ((jzfb.cfg & STN_DAT_PINMASK) >> 4);
+
+	if (((jzfb.cfg & MODE_MASK) == MODE_STN_COLOR_DUAL) ||
+	    ((jzfb.cfg & MODE_MASK) == MODE_STN_MONO_DUAL))
+		pclk >>= 1;
+
+	pll_div = ( REG_CPM_CPCCR & CPM_CPCCR_PCS ); /* clock source,0:pllout/2 1: pllout */
+	pll_div = pll_div ? 1 : 2 ;
+	val = ( __cpm_get_pllout()/pll_div ) / pclk;
+	val--;
+	if ( val > 0x1ff ) {
+		printf("CPM_LPCDR too large, set it to 0x1ff\n");
+		val = 0x1ff;
+	}
+	__cpm_set_pixdiv(val);
+
+	val = pclk * 3 ;	/* LCDClock > 2.5*Pixclock */
+	if ( val > 150000000 ) {
+		printf("Warning: LCDClock=%d\n, LCDClock must less or equal to 150MHz.\n", val);
+		printf("Change LCDClock to 150MHz\n");
+		val = 150000000;
+	}
+	val = ( __cpm_get_pllout()/pll_div ) / val;
+	val--;
+	if ( val > 0x1f ) {
+		printf("CPM_CPCCR.LDIV too large, set it to 0x1f\n");
+		val = 0x1f;
+	}
+	__cpm_set_ldiv( val );
+	REG_CPM_CPCCR |= CPM_CPCCR_CE ; /* update divide */
+
+	__cpm_start_lcd();
+	udelay(1000);
+
+	REG_LCD_DA0 = fbi->fdadr0; /* frame descripter*/
+
+	if (((jzfb.cfg & MODE_MASK) == MODE_STN_COLOR_DUAL) ||
+	    ((jzfb.cfg & MODE_MASK) == MODE_STN_MONO_DUAL))
+		REG_LCD_DA1 = fbi->fdadr1; /* frame descripter*/
+
+	return 0;
+}
+
+void lcd_setcolreg (ushort regno, ushort red, ushort green, ushort blue)
+{
+}
+
+void lcd_initcolregs (void)
+{
+}

package/uboot-xburst/files/cpu/mips/nanonote_gpm940b0.h

@@ -0,0 +1,231 @@
+/*
+ * JzRISC lcd controller
+ *
+ * xiangfu liu <xiangfu.z@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __QI_LB60_GPM940B0_H__
+#define __QI_LB60_GPM940B0_H__
+
+#include <asm/io.h>
+
+#define mdelay(n)	udelay((n)*1000)
+
+#define NR_PALETTE	256
+
+struct lcd_desc{
+	unsigned int next_desc; /* LCDDAx */
+	unsigned int databuf;   /* LCDSAx */
+	unsigned int frame_id;  /* LCDFIDx */ 
+	unsigned int cmd;       /* LCDCMDx */
+};
+
+#define MODE_MASK		0x0f
+#define MODE_TFT_GEN		0x00
+#define MODE_TFT_SHARP		0x01
+#define MODE_TFT_CASIO		0x02
+#define MODE_TFT_SAMSUNG	0x03
+#define MODE_CCIR656_NONINT	0x04
+#define MODE_CCIR656_INT	0x05
+#define MODE_STN_COLOR_SINGLE	0x08
+#define MODE_STN_MONO_SINGLE	0x09
+#define MODE_STN_COLOR_DUAL	0x0a
+#define MODE_STN_MONO_DUAL	0x0b
+#define MODE_8BIT_SERIAL_TFT    0x0c
+
+#define MODE_TFT_18BIT          (1<<7)
+
+#define STN_DAT_PIN1	(0x00 << 4)
+#define STN_DAT_PIN2	(0x01 << 4)
+#define STN_DAT_PIN4	(0x02 << 4)
+#define STN_DAT_PIN8	(0x03 << 4)
+#define STN_DAT_PINMASK	STN_DAT_PIN8
+
+#define STFT_PSHI	(1 << 15)
+#define STFT_CLSHI	(1 << 14)
+#define STFT_SPLHI	(1 << 13)
+#define STFT_REVHI	(1 << 12)
+
+#define SYNC_MASTER	(0 << 16)
+#define SYNC_SLAVE	(1 << 16)
+
+#define DE_P		(0 << 9)
+#define DE_N		(1 << 9)
+
+#define PCLK_P		(0 << 10)
+#define PCLK_N		(1 << 10)
+
+#define HSYNC_P		(0 << 11)
+#define HSYNC_N		(1 << 11)
+
+#define VSYNC_P		(0 << 8)
+#define VSYNC_N		(1 << 8)
+
+#define DATA_NORMAL	(0 << 17)
+#define DATA_INVERSE	(1 << 17)
+
+
+/* Jz LCDFB supported I/O controls. */
+#define FBIOSETBACKLIGHT	0x4688
+#define FBIODISPON		0x4689
+#define FBIODISPOFF		0x468a
+#define FBIORESET		0x468b
+#define FBIOPRINT_REG		0x468c
+
+/*
+ * LCD panel specific definition
+ */
+#define MODE	0xc9		/* 8bit serial RGB */
+#define SPEN	(32*2+21)       /*LCD_SPL */
+#define SPCK	(32*2+23)       /*LCD_CLS */
+#define SPDA	(32*2+22)       /*LCD_D12 */
+#define LCD_RET (32*3+27) 
+
+#define __spi_write_reg1(reg, val) \
+do { \
+	unsigned char no;\
+	unsigned short value;\
+	unsigned char a=0;\
+	unsigned char b=0;\
+	a=reg;\
+	b=val;\
+	__gpio_set_pin(SPEN);\
+	__gpio_set_pin(SPCK);\
+	__gpio_clear_pin(SPDA);\
+	__gpio_clear_pin(SPEN);\
+	udelay(25);\
+	value=((a<<8)|(b&0xFF));\
+	for(no=0;no<16;no++)\
+	{\
+		__gpio_clear_pin(SPCK);\
+		if((value&0x8000)==0x8000)\
+		__gpio_set_pin(SPDA);\
+		else\
+		__gpio_clear_pin(SPDA);\
+		udelay(25);\
+		__gpio_set_pin(SPCK);\
+		value=(value<<1); \
+		udelay(25);\
+	 }\
+	__gpio_set_pin(SPEN);\
+	udelay(100);\
+} while (0)
+
+#define __spi_write_reg(reg, val) \
+do {\
+	__spi_write_reg1((reg<<2|2), val);\
+	udelay(100); \
+}while(0)
+
+#define __lcd_special_pin_init() \
+do { \
+	__gpio_as_output(SPEN); /* use SPDA */\
+	__gpio_as_output(SPCK); /* use SPCK */\
+	__gpio_as_output(SPDA); /* use SPDA */\
+	__gpio_as_output(LCD_RET);\
+} while (0)
+
+#define __lcd_special_on() \
+do { \
+	udelay(50);\
+	__spi_write_reg1(0x05, 0x16); \
+	__spi_write_reg1(0x04, 0x0b); \
+	__spi_write_reg1(0x07, 0x8d); \
+	__spi_write_reg1(0x01, 0x95); \
+	__spi_write_reg1(0x08, 0xc0); \
+	__spi_write_reg1(0x03, 0x40); \
+	__spi_write_reg1(0x06, 0x75); \
+	__spi_write_reg1(0x13, 0x01); \
+	__spi_write_reg1(0x05, 0x57); \
+} while (0)
+
+#define __lcd_special_off() \
+do {					\
+	__spi_write_reg1(0x05, 0x5e);	\
+} while (0)
+
+#define __lcd_display_pin_init() \
+do { \
+	__lcd_special_pin_init();\
+	__gpio_as_pwm();\
+	__lcd_set_backlight_level(8);\
+} while (0)
+
+#define __lcd_display_on() \
+do { \
+	__lcd_set_backlight_level(8); \
+	__lcd_special_on();\
+} while (0)
+
+#define __lcd_display_off() \
+do { \
+	__lcd_set_backlight_level(0); \
+	__lcd_special_off();\
+} while (0)
+
+#define __lcd_set_backlight_level(n)\
+do { \
+	__gpio_as_output(LCD_RET); \
+	__gpio_set_pin(LCD_RET); \
+} while (0)
+
+#if defined(CONFIG_SAKC)
+#define __lcd_close_backlight() \
+do { \
+	__gpio_as_output(GPIO_PWM); \
+	__gpio_clear_pin(GPIO_PWM); \
+} while (0)
+#endif
+
+#if defined(CONFIG_SAKC)
+#define __lcd_display_pin_init() \
+do { \
+	__cpm_start_tcu(); \
+	__lcd_special_pin_init(); \
+} while (0)
+
+#define __lcd_display_on() \
+do { \
+	__lcd_special_on(); \
+} while (0)
+
+#define __lcd_display_off() \
+do { \
+	__lcd_special_off(); \
+} while (0)
+#else
+#define __lcd_display_pin_init() \
+do { \
+	__cpm_start_tcu(); \
+	__lcd_special_pin_init(); \
+} while (0)
+
+#define __lcd_display_on() \
+do { \
+	__gpio_set_pin(GPIO_DISP_OFF_N); \
+	__lcd_special_on(); \
+} while (0)
+
+#define __lcd_display_off() \
+do { \
+	__lcd_special_off(); \
+	__gpio_clear_pin(GPIO_DISP_OFF_N); \
+} while (0)
+#endif
+
+#endif /* __QI_LB60_GPM940B0_H__ */

package/uboot-xburst/files/cpu/mips/usb_boot.S

@@ -0,0 +1,880 @@
+/*
+ *  for jz4740 usb boot
+ *
+ *  Copyright (c) 2009	Xiangfu Liu <xiangfu.z@gmail.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+    .set noreorder
+    .globl usb_boot
+    .text
+
+//----------------------------------------------------------------------
+// Both NAND and USB boot load data to D-Cache first, then transfer
+// data from D-Cache to I-Cache, and jump to execute the code in I-Cache.
+// So init caches first and then dispatch to a proper boot routine.
+//----------------------------------------------------------------------
+
+.macro load_addr reg addr
+	li \reg, 0x80000000
+	addiu \reg, \reg, \addr
+	la $2, usbboot_begin
+	subu \reg, \reg, $2
+.endm
+
+usb_boot:
+	//--------------------------------------------------------------
+	// Initialize PLL: set ICLK to 84MHz and HCLK to 42MHz.
+	//--------------------------------------------------------------
+	la	$9, 0xB0000000		// CPCCR: Clock Control Register
+	la	$8, 0x42041110		// I:S:M:P=1:2:2:2
+	sw	$8, 0($9)
+
+	la	$9, 0xB0000010		// CPPCR: PLL Control Register
+	la	$8, 0x06000120		// M=12 N=0 D=0 CLK=12*(M+2)/(N+2)
+	sw	$8, 0($9)
+
+	mtc0	$0, $26			// CP0_ERRCTL, restore WST reset state
+	nop
+
+	mtc0	$0, $16			// CP0_CONFIG
+	nop
+
+	// Relocate code to beginning of the ram
+
+	la $2, usbboot_begin
+	la $3, usbboot_end
+	li $4, 0x80000000
+
+1:
+	lw $5, 0($2)
+	sw $5, 0($4)
+	addiu $2, $2, 4
+	bne $2, $3, 1b
+	addiu $4, $4, 4
+
+	li $2, 0x80000000
+	ori $3, $2, 0
+	addiu $3, $3, usbboot_end
+	la $4, usbboot_begin
+	subu $3, $3, $4
+
+
+2:
+	cache	0x0, 0($2)		// Index_Invalidate_I
+	cache	0x1, 0($2)		// Index_Writeback_Inv_D
+	addiu	$2, $2, 32
+	subu $4, $3, $2
+	bgtz	$4, 2b
+	nop
+
+	load_addr $3, usb_boot_return
+
+	jr $3
+
+usbboot_begin:
+
+init_caches:
+	li	$2, 3			// cacheable for kseg0 access
+	mtc0	$2, $16			// CP0_CONFIG
+	nop
+
+	li	$2, 0x20000000		// enable idx-store-data cache insn
+	mtc0	$2, $26			// CP0_ERRCTL
+
+	ori	$2, $28, 0		// start address
+	ori	$3, $2, 0x3fe0		// end address, total 16KB
+	mtc0	$0, $28, 0		// CP0_TAGLO
+	mtc0	$0, $28, 1		// CP0_DATALO
+cache_clear_a_line:
+	cache	0x8, 0($2)		// Index_Store_Tag_I
+	cache	0x9, 0($2)		// Index_Store_Tag_D
+	bne	$2, $3, cache_clear_a_line
+	addiu	$2, $2, 32		// increment CACHE_LINE_SIZE
+
+	ori	$2, $28, 0		// start address
+	ori	$3, $2, 0x3fe0		// end address, total 16KB
+	la	$4, 0x1ffff000		// physical address and 4KB page mask
+cache_alloc_a_line:
+	and	$5, $2, $4
+	ori	$5, $5, 1		// V bit of the physical tag
+	mtc0	$5, $28, 0		// CP0_TAGLO
+	cache	0x8, 0($2)		// Index_Store_Tag_I
+	cache	0x9, 0($2)		// Index_Store_Tag_D
+	bne	$2, $3, cache_alloc_a_line
+	addiu	$2, $2, 32		// increment CACHE_LINE_SIZE
+
+	nop
+	nop
+	nop
+	//--------------------------------------------------------------
+	// Transfer data from dcache to icache, then jump to icache.
+	//
+	// Input parameters:
+	//
+	// $19: data length in bytes
+	// $20: jump target address
+	//--------------------------------------------------------------
+xfer_d2i:
+
+	ori	$8, $20, 0
+	addu	$9, $8, $19		// total 16KB
+
+1:
+	cache	0x0, 0($8)		// Index_Invalidate_I
+	cache	0x1, 0($8)		// Index_Writeback_Inv_D
+	bne	$8, $9, 1b
+	addiu	$8, $8, 32
+
+	// flush write-buffer
+	sync
+
+	// Invalidate BTB
+	mfc0	$8, $16, 7		// CP0_CONFIG
+	nop
+	ori	$8, 2
+	mtc0	$8, $16, 7
+	nop
+
+	// Overwrite config to disable ram initalisation
+	li $2, 0xff
+	sb $2, 20($20)
+
+	jalr	$20
+	nop
+
+icache_return:
+	//--------------------------------------------------------------
+	// User code can return to here after executing itself in 
+	// icache, by jumping to $31.
+	//--------------------------------------------------------------
+	b	usb_boot_return
+	nop
+
+
+usb_boot_return:
+	//--------------------------------------------------------------
+	// Enable the USB PHY
+	//--------------------------------------------------------------
+	la	$9, 0xB0000024		// CPM_SCR
+	lw	$8, 0($9)
+	ori	$8, 0x40		// USBPHY_ENABLE
+	sw	$8, 0($9)
+
+	//--------------------------------------------------------------
+	// Initialize USB registers
+	//--------------------------------------------------------------
+	la	$27, 0xb3040000		// USB registers base address
+
+	sb	$0, 0x0b($27)		// INTRUSBE: disable common USB interrupts
+	sh	$0, 0x06($27)		// INTRINE: disable EPIN interrutps
+	sh	$0, 0x08($27)		// INTROUTE: disable EPOUT interrutps
+
+	li	$9, 0x61
+	sb	$9, 0x01($27)		// POWER: HSENAB | SUSPENDM | SOFTCONN
+
+	//--------------------------------------------------------------
+	// Initialize USB states
+	//--------------------------------------------------------------
+	li	$22, 0			// set EP0 to IDLE state
+	li	$23, 1			// no data stage
+
+	//--------------------------------------------------------------
+	// Main loop of polling the usb commands
+	//--------------------------------------------------------------
+usb_command_loop:
+	lbu	$9, 0x0a($27)		// read INTRUSB
+	andi	$9, 0x04		// check USB_INTR_RESET
+	beqz	$9, check_intr_ep0in
+	nop
+
+	//--------------------------------------------------------------
+ 	// 1. Handle USB reset interrupt
+	//--------------------------------------------------------------
+handle_reset_intr:
+	lbu	$9, 0x01($27)		// read POWER
+	andi	$9, 0x10		// test HS_MODE
+	bnez	$9, _usb_set_maxpktsize
+	li	$9, 512			// max packet size of HS mode
+	li	$9, 64			// max packet size of FS mode
+
+_usb_set_maxpktsize:
+	li	$8, 1
+	sb	$8, 0x0e($27)		// set INDEX 1
+
+	sh	$9, 0x10($27)		// INMAXP
+	sb	$0, 0x13($27)		// INCSRH
+	sh	$9, 0x14($27)		// OUTMAXP
+	sb	$0, 0x17($27)		// OUTCSRH
+
+_usb_flush_fifo:
+	li	$8, 0x48		// INCSR_CDT && INCSR_FF
+	sb	$8, 0x12($27)		// INCSR
+	li	$8, 0x90		// OUTCSR_CDT && OUTCSR_FF
+	sb	$8, 0x16($27)		// OUTCSR
+
+	li	$22, 0			// set EP0 to IDLE state
+	li	$23, 1			// no data stage
+
+	//--------------------------------------------------------------
+	// 2. Check and handle EP0 interrupt
+	//--------------------------------------------------------------
+check_intr_ep0in:
+	lhu	$10, 0x02($27)		// read INTRIN
+	andi	$9, $10, 0x1		// check EP0 interrupt
+	beqz	$9, check_intr_ep1in
+	nop
+
+handle_ep0_intr:
+	sb	$0, 0x0e($27)		// set INDEX 0
+	lbu	$11, 0x12($27)		// read CSR0
+
+	andi	$9, $11, 0x04		// check SENTSTALL
+	beqz	$9, _ep0_setupend
+	nop
+
+_ep0_sentstall:
+	andi	$9, $11, 0xdb
+	sb	$9, 0x12($27)		// clear SENDSTALL and SENTSTALL
+	li	$22, 0			// set EP0 to IDLE state
+
+_ep0_setupend:
+	andi	$9, $11, 0x10		// check SETUPEND
+	beqz	$9, ep0_idle_state
+	nop
+
+	ori	$9, $11, 0x80
+	sb	$9, 0x12($27)		// set SVDSETUPEND
+	li	$22, 0			// set EP0 to IDLE state
+
+ep0_idle_state:
+	bnez	$22, ep0_tx_state
+	nop
+
+	//--------------------------------------------------------------
+	// 2.1 Handle EP0 IDLE state interrupt
+	//--------------------------------------------------------------
+	andi	$9, $11, 0x01		// check OUTPKTRDY
+	beqz	$9, check_intr_ep1in
+	nop
+
+	//--------------------------------------------------------------
+	// Read 8-bytes setup packet from the FIFO
+	//--------------------------------------------------------------
+	lw	$25, 0x20($27)		// first word of setup packet
+	lw	$26, 0x20($27)		// second word of setup packet
+
+	andi	$9, $25, 0x60		// bRequestType & USB_TYPE_MASK
+	beqz	$9, _ep0_std_req
+	nop
+
+	//--------------------------------------------------------------
+	// 2.1.1 Vendor-specific setup request
+	//--------------------------------------------------------------
+_ep0_vend_req:
+	li	$22, 0			// set EP0 to IDLE state
+	li	$23, 1			// NoData = 1
+
+	andi	$9, $25, 0xff00		// check bRequest
+	srl	$9, $9, 8
+	beqz	$9, __ep0_get_cpu_info
+	sub	$8, $9, 0x1
+	beqz	$8, __ep0_set_data_address
+	sub	$8, $9, 0x2
+	beqz	$8, __ep0_set_data_length
+	sub	$8, $9, 0x3
+	beqz	$8, __ep0_flush_caches
+	sub	$8, $9, 0x4
+	beqz	$8, __ep0_prog_start1
+	sub	$8, $9, 0x5
+	beqz	$8, __ep0_prog_start2
+	nop
+	b	_ep0_idle_state_fini	// invalid request
+	nop
+
+__ep0_get_cpu_info:
+	load_addr $20, cpu_info_data	// data pointer to transfer
+	li	$21, 8			// bytes left to transfer
+	li	$22, 1			// set EP0 to TX state
+	li	$23, 0			// NoData = 0
+
+	b	_ep0_idle_state_fini
+	nop
+
+__ep0_set_data_address:
+	li	$9, 0xffff0000
+	and	$9, $25, $9
+	andi	$8, $26, 0xffff
+	or	$20, $9, $8		// data address of next transfer
+
+	b	_ep0_idle_state_fini
+	nop
+
+__ep0_set_data_length:
+	li	$9, 0xffff0000
+	and	$9, $25, $9
+	andi	$8, $26, 0xffff
+	or	$21, $9, $8		// data length of next transfer
+
+	li	$9, 0x48		// SVDOUTPKTRDY and DATAEND
+	sb	$9, 0x12($27)		// CSR0
+
+	// We must write packet to FIFO before EP1-IN interrupt here.
+	b	handle_epin1_intr
+	nop
+
+__ep0_flush_caches:
+	// Flush dcache and invalidate icache.
+	li	$8, 0x80000000
+	addi	$9, $8, 0x3fe0		// total 16KB
+
+1:
+	cache	0x0, 0($8)		// Index_Invalidate_I
+	cache	0x1, 0($8)		// Index_Writeback_Inv_D
+	bne	$8, $9, 1b
+	addiu	$8, $8, 32
+
+	// flush write-buffer
+	sync
+
+	// Invalidate BTB
+	mfc0	$8, $16, 7		// CP0_CONFIG
+	nop
+	ori	$8, 2
+	mtc0	$8, $16, 7
+	nop
+
+	b	_ep0_idle_state_fini
+	nop
+
+__ep0_prog_start1:
+	li	$9, 0x48		// SVDOUTPKTRDY and DATAEND
+	sb	$9, 0x12($27)		// CSR0
+
+	li	$9, 0xffff0000
+	and	$9, $25, $9
+	andi	$8, $26, 0xffff
+	or	$20, $9, $8		// target address
+
+	b	xfer_d2i
+	li	$19, 0x2000		// 16KB data length
+
+__ep0_prog_start2:
+	li	$9, 0x48		// SVDOUTPKTRDY and DATAEND
+	sb	$9, 0x12($27)		// CSR0
+
+	li	$9, 0xffff0000
+	and	$9, $25, $9
+	andi	$8, $26, 0xffff
+	or	$20, $9, $8		// target address
+
+	jalr	$20			// jump, and place the return address in $31
+	nop
+
+__ep0_prog_start2_return:
+	// User code can return to here after executing itself, by jumping to $31.
+	b	usb_boot_return
+	nop
+
+	//--------------------------------------------------------------
+	// 2.1.2 Standard setup request
+	//--------------------------------------------------------------
+_ep0_std_req:
+	andi	$12, $25, 0xff00	// check bRequest
+	srl	$12, $12, 8
+	sub	$9, $12, 0x05		// check USB_REQ_SET_ADDRESS
+	bnez	$9, __ep0_req_set_config
+	nop
+
+	//--------------------------------------------------------------
+	// Handle USB_REQ_SET_ADDRESS
+	//--------------------------------------------------------------
+__ep0_req_set_addr:
+	srl	$9, $25, 16		// get wValue
+	sb	$9, 0x0($27)		// set FADDR
+	li	$23, 1			// NoData = 1
+	b	_ep0_idle_state_fini
+	nop
+
+__ep0_req_set_config:
+	sub	$9, $12, 0x09		// check USB_REQ_SET_CONFIGURATION
+	bnez	$9, __ep0_req_get_desc
+	nop
+
+	//--------------------------------------------------------------
+	// Handle USB_REQ_SET_CONFIGURATION
+	//--------------------------------------------------------------
+	li	$23, 1			// NoData = 1
+	b	_ep0_idle_state_fini
+	nop
+
+__ep0_req_get_desc:
+	sub	$9, $12, 0x06		// check USB_REQ_GET_DESCRIPTOR
+	bnez	$9, _ep0_idle_state_fini
+	li	$23, 1			// NoData = 1
+
+	//--------------------------------------------------------------
+	// Handle USB_REQ_GET_DESCRIPTOR
+	//--------------------------------------------------------------
+	li	$23, 0			// NoData = 0
+
+	srl	$9, $25, 24		// wValue >> 8
+	sub	$8, $9, 0x01		// check USB_DT_DEVICE
+	beqz	$8, ___ep0_get_dev_desc
+	srl	$21, $26, 16		// get wLength
+	sub	$8, $9, 0x02		// check USB_DT_CONFIG
+	beqz	$8, ___ep0_get_conf_desc
+	sub	$8, $9, 0x03		// check USB_DT_STRING
+	beqz	$8, ___ep0_get_string_desc
+	sub	$8, $9, 0x06		// check USB_DT_DEVICE_QUALIFIER
+	beqz	$8, ___ep0_get_dev_qualifier
+	nop
+	b	_ep0_idle_state_fini
+	nop
+
+___ep0_get_dev_desc:
+	load_addr	$20, device_desc	// data pointer
+	li	$22, 1			// set EP0 to TX state
+	sub	$8, $21, 18
+	blez	$8, _ep0_idle_state_fini // wLength <= 18
+	nop
+	li	$21, 18			// max length of device_desc
+	b	_ep0_idle_state_fini
+	nop
+
+___ep0_get_dev_qualifier:
+	load_addr	$20, dev_qualifier	// data pointer
+	li	$22, 1			// set EP0 to TX state
+	sub	$8, $21, 10
+	blez	$8, _ep0_idle_state_fini // wLength <= 10
+	nop
+	li	$21, 10			// max length of dev_qualifier
+	b	_ep0_idle_state_fini
+	nop
+
+___ep0_get_conf_desc:
+	load_addr	$20, config_desc_fs	// data pointer of FS mode
+	lbu	$8, 0x01($27)		// read POWER
+	andi	$8, 0x10		// test HS_MODE
+	beqz	$8, ___ep0_get_conf_desc2
+	nop
+	load_addr $20, config_desc_hs	// data pointer of HS mode
+
+___ep0_get_conf_desc2:
+	li	$22, 1			// set EP0 to TX state
+	sub	$8, $21, 32
+	blez	$8, _ep0_idle_state_fini // wLength <= 32
+	nop
+	li	$21, 32			// max length of config_desc
+	b	_ep0_idle_state_fini
+	nop
+
+___ep0_get_string_desc:
+	li	$22, 1			// set EP0 to TX state
+
+	srl	$9, $25, 16		// wValue & 0xff
+	andi	$9, 0xff
+
+	sub	$8, $9, 1
+	beqz	$8, ___ep0_get_string_manufacture
+	sub	$8, $9, 2
+	beqz	$8, ___ep0_get_string_product
+	nop
+
+___ep0_get_string_lang_ids:
+	load_addr	$20, string_lang_ids	// data pointer
+	b	_ep0_idle_state_fini
+	li	$21, 4			// data length
+
+___ep0_get_string_manufacture:
+	load_addr	$20, string_manufacture	// data pointer
+	b	_ep0_idle_state_fini
+	li	$21, 16			// data length
+
+___ep0_get_string_product:
+	load_addr	$20, string_product	// data pointer
+	b	_ep0_idle_state_fini
+	li	$21, 46			// data length
+
+_ep0_idle_state_fini:
+	li	$9, 0x40		// SVDOUTPKTRDY
+	beqz	$23, _ep0_idle_state_fini2
+	nop
+	ori	$9, $9, 0x08		// DATAEND
+_ep0_idle_state_fini2:
+	sb	$9, 0x12($27)		// CSR0
+	beqz	$22, check_intr_ep1in
+	nop
+
+	//--------------------------------------------------------------
+	// 2.2 Handle EP0 TX state interrupt
+	//--------------------------------------------------------------
+ep0_tx_state:
+	sub	$9, $22, 1
+	bnez	$9, check_intr_ep1in
+	nop
+
+	sub	$9, $21, 64		// max packetsize
+	blez	$9, _ep0_tx_state2	// data count <= 64
+	ori	$19, $21, 0
+	li	$19, 64
+
+_ep0_tx_state2:
+	beqz	$19, _ep0_tx_state3	// send ZLP
+	ori	$18, $19, 0		// record bytes to be transferred
+	sub	$21, $21, $19		// decrement data count
+
+_ep0_fifo_write_loop:
+	lbu	$9, 0($20)		// read data
+	sb	$9, 0x20($27)		// load FIFO
+	sub	$19, $19, 1		// decrement counter
+	bnez	$19, _ep0_fifo_write_loop
+	addi	$20, $20, 1		// increment data pointer
+
+	sub	$9, $18, 64		// max packetsize
+	beqz	$9, _ep0_tx_state4
+	nop
+
+_ep0_tx_state3:
+	// transferred bytes < max packetsize
+	li	$9, 0x0a		// set INPKTRDY and DATAEND
+	sb	$9, 0x12($27)		// CSR0
+	li	$22, 0			// set EP0 to IDLE state
+	b	check_intr_ep1in
+	nop
+
+_ep0_tx_state4:
+	// transferred bytes == max packetsize
+	li	$9, 0x02		// set INPKTRDY
+	sb	$9, 0x12($27)		// CSR0
+	b	check_intr_ep1in
+	nop
+
+	//--------------------------------------------------------------
+	// 3. Check and handle EP1 BULK-IN interrupt
+	//--------------------------------------------------------------
+check_intr_ep1in:
+	andi	$9, $10, 0x2		// check EP1 IN interrupt
+	beqz	$9, check_intr_ep1out
+	nop
+
+handle_epin1_intr:
+	li	$9, 1
+	sb	$9, 0x0e($27)		// set INDEX 1
+	lbu	$9, 0x12($27)		// read INCSR
+
+	andi	$8, $9, 0x2		// check INCSR_FFNOTEMPT
+	bnez	$8, _epin1_tx_state4
+	nop
+
+_epin1_write_fifo:
+	lhu	$9, 0x10($27)		// get INMAXP
+	sub	$8, $21, $9
+	blez	$8, _epin1_tx_state1	// bytes left <= INMAXP
+	ori	$19, $21, 0
+	ori	$19, $9, 0
+
+_epin1_tx_state1:
+	beqz	$19, _epin1_tx_state4	// No data
+	nop
+
+	sub	$21, $21, $19		// decrement data count
+
+	srl	$5, $19, 2		// # of word
+	andi	$6, $19, 0x3		// # of byte
+	beqz	$5, _epin1_tx_state2
+	nop
+
+_epin1_fifo_write_word:
+	lw	$9, 0($20)		// read data from source address
+	sw	$9, 0x24($27)		// write FIFO
+	sub	$5, $5, 1		// decrement counter
+	bnez	$5, _epin1_fifo_write_word
+	addiu	$20, $20, 4		// increment dest address
+
+_epin1_tx_state2:
+	beqz	$6, _epin1_tx_state3
+	nop
+
+_epin1_fifo_write_byte:
+	lbu	$9, 0($20)		// read data from source address
+	sb	$9, 0x24($27)		// write FIFO
+	sub	$6, $6, 1		// decrement counter
+	bnez	$6, _epin1_fifo_write_byte
+	addiu	$20, $20, 1		// increment dest address
+
+_epin1_tx_state3:
+	li	$9, 0x1
+	sb	$9, 0x12($27)		// INCSR, set INPKTRDY
+
+_epin1_tx_state4:
+	// nop
+
+	//--------------------------------------------------------------
+	// 4. Check and handle EP1 BULK-OUT interrupt
+	//--------------------------------------------------------------
+check_intr_ep1out:
+	lhu	$9, 0x04($27)		// read INTROUT
+	andi	$9, 0x2
+	beqz	$9, check_status_next
+	nop
+
+handle_epout1_intr:
+	li	$9, 1
+	sb	$9, 0x0e($27)		// set INDEX 1
+
+	lbu	$9, 0x16($27)		// read OUTCSR
+	andi	$9, 0x1			// check OUTPKTRDY
+	beqz	$9, check_status_next
+	nop
+
+_epout1_read_fifo:
+	lhu	$19, 0x18($27)		// read OUTCOUNT
+	srl	$5, $19, 2		// # of word
+	andi	$6, $19, 0x3		// # of byte
+	beqz	$5, _epout1_rx_state1
+	nop
+
+_epout1_fifo_read_word:
+	lw	$9, 0x24($27)		// read FIFO
+	sw	$9, 0($20)		// store to dest address
+	sub	$5, $5, 1		// decrement counter
+	bnez	$5, _epout1_fifo_read_word
+	addiu	$20, $20, 4		// increment dest address
+
+_epout1_rx_state1:
+	beqz	$6, _epout1_rx_state2
+	nop
+
+_epout1_fifo_read_byte:
+	lbu	$9, 0x24($27)		// read FIFO
+	sb	$9, 0($20)		// store to dest address
+	sub	$6, $6, 1		// decrement counter
+	bnez	$6, _epout1_fifo_read_byte
+	addiu	$20, $20, 1		// increment dest address
+
+_epout1_rx_state2:
+	sb	$0, 0x16($27)		// clear OUTPKTRDY
+
+check_status_next:
+	b	usb_command_loop
+	nop
+
+//--------------------------------------------------------------
+// Device/Configuration/Interface/Endpoint/String Descriptors
+//--------------------------------------------------------------
+
+	.align	2
+device_desc:
+	.byte	0x12		// bLength
+	.byte	0x01		// bDescriptorType
+	.byte	0x00		// bcdUSB
+	.byte	0x02		// bcdUSB
+	.byte	0x00		// bDeviceClass
+	.byte	0x00		// bDeviceSubClass
+	.byte	0x00		// bDeviceProtocol
+	.byte	0x40		// bMaxPacketSize0
+	.byte	0x1a		// idVendor
+	.byte	0x60		// idVendor
+	.byte	0x40		// idProduct
+	.byte	0x47		// idProduct
+	.byte	0x00		// bcdDevice
+	.byte	0x01		// bcdDevice
+	.byte	0x01		// iManufacturer
+	.byte	0x02		// iProduct
+	.byte	0x00		// iSerialNumber
+	.byte	0x01		// bNumConfigurations
+
+	.align	2
+dev_qualifier:
+	.byte	0x0a		// bLength
+	.byte	0x06		// bDescriptorType
+	.byte	0x00		// bcdUSB
+	.byte	0x02		// bcdUSB
+	.byte	0x00		// bDeviceClass
+	.byte	0x00		// bDeviceSubClass
+	.byte	0x00		// bDeviceProtocol
+	.byte	0x40		// bMaxPacketSize0
+	.byte	0x01		// bNumConfigurations
+	.byte	0x00		// bRESERVED
+
+	.align	2
+config_desc_hs:
+	.byte	0x09		// bLength
+	.byte	0x02		// bDescriptorType
+	.byte	0x20		// wTotalLength
+	.byte	0x00		// wTotalLength
+	.byte	0x01		// bNumInterfaces
+	.byte	0x01		// bConfigurationValue
+	.byte	0x00		// iConfiguration
+	.byte	0xc0		// bmAttributes
+	.byte	0x01		// MaxPower
+intf_desc_hs:
+	.byte	0x09		// bLength
+	.byte	0x04		// bDescriptorType
+	.byte	0x00		// bInterfaceNumber
+	.byte	0x00		// bAlternateSetting
+	.byte	0x02		// bNumEndpoints
+	.byte	0xff		// bInterfaceClass
+	.byte	0x00		// bInterfaceSubClass
+	.byte	0x50		// bInterfaceProtocol
+	.byte	0x00		// iInterface
+ep1_desc_hs:
+	.byte	0x07		// bLength
+	.byte	0x05		// bDescriptorType
+	.byte	0x01		// bEndpointAddress
+	.byte	0x02		// bmAttributes
+	.byte	0x00		// wMaxPacketSize
+	.byte	0x02		// wMaxPacketSize
+	.byte	0x00		// bInterval
+ep2_desc_hs:
+	.byte	0x07		// bLength
+	.byte	0x05		// bDescriptorType
+	.byte	0x81		// bEndpointAddress
+	.byte	0x02		// bmAttributes
+	.byte	0x00		// wMaxPacketSize
+	.byte	0x02		// wMaxPacketSize
+	.byte	0x00		// bInterval
+
+	.align	2
+config_desc_fs:
+	.byte	0x09		// bLength
+	.byte	0x02		// bDescriptorType
+	.byte	0x20		// wTotalLength
+	.byte	0x00		// wTotalLength
+	.byte	0x01		// bNumInterfaces
+	.byte	0x01		// bConfigurationValue
+	.byte	0x00		// iConfiguration
+	.byte	0xc0		// bmAttributes
+	.byte	0x01		// MaxPower
+intf_desc_fs:
+	.byte	0x09		// bLength
+	.byte	0x04		// bDescriptorType
+	.byte	0x00		// bInterfaceNumber
+	.byte	0x00		// bAlternateSetting
+	.byte	0x02		// bNumEndpoints
+	.byte	0xff		// bInterfaceClass
+	.byte	0x00		// bInterfaceSubClass
+	.byte	0x50		// bInterfaceProtocol
+	.byte	0x00		// iInterface
+ep1_desc_fs:
+	.byte	0x07		// bLength
+	.byte	0x05		// bDescriptorType
+	.byte	0x01		// bEndpointAddress
+	.byte	0x02		// bmAttributes
+	.byte	0x40		// wMaxPacketSize
+	.byte	0x00		// wMaxPacketSize
+	.byte	0x00		// bInterval
+ep2_desc_fs:
+	.byte	0x07		// bLength
+	.byte	0x05		// bDescriptorType
+	.byte	0x81		// bEndpointAddress
+	.byte	0x02		// bmAttributes
+	.byte	0x40		// wMaxPacketSize
+	.byte	0x00		// wMaxPacketSize
+	.byte	0x00		// bInterval
+
+	.align	2
+string_lang_ids:
+	.byte	0x04
+	.byte	0x03
+	.byte	0x09
+	.byte	0x04
+
+	.align	2
+string_manufacture:
+	.byte	0x10
+	.byte	0x03
+	.byte	0x49
+	.byte	0x00
+	.byte	0x6e
+	.byte	0x00
+	.byte	0x67
+	.byte	0x00
+	.byte	0x65
+	.byte	0x00
+	.byte	0x6e
+	.byte	0x00
+	.byte	0x69
+	.byte	0x00
+	.byte	0x63
+	.byte	0x00
+
+	.align	2
+string_product:
+	.byte	0x2e
+	.byte	0x03
+	.byte	0x4a
+	.byte	0x00
+	.byte	0x5a
+	.byte	0x00
+	.byte	0x34
+	.byte	0x00
+	.byte	0x37
+	.byte	0x00
+	.byte	0x34
+	.byte	0x00
+	.byte	0x30
+	.byte	0x00
+	.byte	0x20
+	.byte	0x00
+	.byte	0x55
+	.byte	0x00
+	.byte	0x53
+	.byte	0x00
+	.byte	0x42
+	.byte	0x00
+	.byte	0x20
+	.byte	0x00
+	.byte	0x42
+	.byte	0x00
+	.byte	0x6f
+	.byte	0x00
+	.byte	0x6f
+	.byte	0x00
+	.byte	0x74
+	.byte	0x00
+	.byte	0x20
+	.byte	0x00
+	.byte	0x44
+	.byte	0x00
+	.byte	0x65
+	.byte	0x00
+	.byte	0x76
+	.byte	0x00
+	.byte	0x69
+	.byte	0x00
+	.byte	0x63
+	.byte	0x00
+	.byte	0x65
+	.byte	0x00
+
+	.align	2
+cpu_info_data:
+	.byte	0x4a
+	.byte	0x5a
+	.byte	0x34
+	.byte	0x37
+	.byte	0x34
+	.byte	0x30
+	.byte	0x56
+	.byte	0x31
+usbboot_end:
+
+    .set reorder

package/uboot-xburst/files/include/configs/avt2.h

@@ -0,0 +1,26 @@
+#ifndef __CONFIG_AVT2_H
+#define __CONFIG_AVT2_H
+
+#include <configs/nanonote.h>
+
+#define CONFIG_AVT2 1
+
+#define CONFIG_BOOTARGS		"mem=64M console=ttyS0,57600n8 ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait avt2=1"
+#define CONFIG_BOOTARGSFROMSD	"mem=64M console=ttyS0,57600n8 rootfstype=ext2 root=/dev/mmcblk0p1 rw rootwait avt2=1"
+#define CONFIG_BOOTCOMMAND	"nand read 0x80600000 0x400000 0x200000;bootm"
+
+/* SDRAM paramters */
+#define SDRAM_BW16		1	/* Data bus width: 0-32bit, 1-16bit */
+#define SDRAM_BANK4		1	/* Banks each chip: 0-2bank, 1-4bank */
+#define SDRAM_ROW		13	/* Row address: 11 to 13 */
+#define SDRAM_COL		10	/* Column address: 8 to 12 */
+#define SDRAM_CASL		2	/* CAS latency: 2 or 3 */
+
+/* SDRAM Timings, unit: ns */
+#define SDRAM_TRAS		45	/* RAS# Active Time */
+#define SDRAM_RCD		20	/* RAS# to CAS# Delay */
+#define SDRAM_TPC		20	/* RAS# Precharge Time */
+#define SDRAM_TRWL		7	/* Write Latency Time */
+#define SDRAM_TREF	        15625	/* Refresh period: 8192 cycles/64ms */
+
+#endif	/* __CONFIG_AVT_H */

package/uboot-xburst/files/include/configs/n516.h

@@ -0,0 +1,311 @@
+/*
+ * (C) Copyright 2006
+ * Ingenic Semiconductor, <jlwei@ingenic.cn>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * This file contains the configuration parameters for the pavo board.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+//#define DEBUG
+//#define DEBUG_SHELL
+
+#define CONFIG_MIPS32		1  /* MIPS32 CPU core */
+#define CONFIG_JzRISC		1  /* JzRISC core */
+#define CONFIG_JZSOC		1  /* Jz SoC */
+#define CONFIG_JZ4740		1  /* Jz4740 SoC */
+#define CONFIG_PAVO		1  /* PAVO validation board */
+
+#define CONFIG_BOARD_NAME	"n516"
+#define CONFIG_BOARD_HWREV	"1.0"
+#define CONFIG_FIRMWARE_EPOCH	"0"
+#define CONFIG_UPDATE_TMPBUF	0x80600000
+#define CONFIG_UPDATE_CHUNKSIZE	0x800000
+#define CONFIG_UPDATE_FILENAME	"update.oifw"
+#define CONFIG_UPDATE_FILEEXT	".oifw"
+#define CONFIG_UBI_PARTITION	"UBI"
+
+#define CONFIG_SKIP_LOWLEVEL_INIT	1
+#undef  CONFIG_SKIP_RELOCATE_UBOOT
+
+#if 0
+#define CONFIG_LCD                 /* LCD support */
+#define CONFIG_JZLCD_METRONOME_800x600
+#define LCD_BPP			LCD_COLOR8
+
+#define WFM_DATA_SIZE  ( 1 << 14 )
+#define CONFIG_METRONOME_WF_LEN (64 * (1 << 10))
+#define CONFIG_METRONOME_WF_NAND_OFFSET (0x100000)
+#define BMP_LOGO_HEIGHT 0
+#define CONFIG_UBI_WF_VOLUME "waveforms"
+#define CONFIG_UBI_BOOTSPLASH_VOLUME "bootsplash"
+#define CONFIG_METRONOME_BOOTSPLASH_LEN 480000
+#endif
+
+#if 0
+#define CONFIG_JZSOC_I2C
+#define CONFIG_HARD_I2C
+#define CONFIG_SYS_I2C_SPEED	100000
+#define CONFIG_SYS_I2C_SLAVE	0
+#define CONFIG_LPC_I2C_ADDR	0x54
+#endif
+
+#define JZ4740_NORBOOT_CFG	JZ4740_NORBOOT_16BIT	/* NOR Boot config code */
+#define JZ4740_NANDBOOT_CFG	JZ4740_NANDBOOT_B8R3	/* NAND Boot config code */
+
+#define CONFIG_SYS_CPU_SPEED		336000000	/* CPU clock: 336 MHz */
+#define CONFIG_SYS_EXTAL		12000000	/* EXTAL freq: 12 MHz */
+#define	CONFIG_SYS_HZ			(CONFIG_SYS_EXTAL/256) /* incrementer freq */
+
+#define CONFIG_SYS_UART_BASE  		UART0_BASE	/* Base of the UART channel */
+
+#define CONFIG_BAUDRATE		57600
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+
+#define CONFIG_MMC      	1
+#define CONFIG_GENERIC_MMC	1
+#define CONFIG_JZ_MMC		1
+#define CONFIG_FAT		1
+
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 ">"
+#define CONFIG_CMDLINE_EDITING
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+#include <config_cmd_default.h>
+
+#undef CONFIG_CMD_BDI		/* bdinfo			*/
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_ECHO		/* echo arguments		*/
+#undef CONFIG_CMD_FLASH	/* flinfo, erase, protect	*/
+#undef CONFIG_CMD_FPGA		/* FPGA configuration Support	*/
+#undef CONFIG_CMD_IMI		/* iminfo			*/
+#undef CONFIG_CMD_ITEST	/* Integer (and string) test	*/
+#undef CONFIG_CMD_LOADB	/* loadb			*/
+#undef CONFIG_CMD_LOADS	/* loads			*/
+#undef CONFIG_CMD_NFS		/* NFS support			*/
+#undef CONFIG_CMD_SETGETDCR	/* DCR support on 4xx		*/
+#undef CONFIG_CMD_SOURCE	/* "source" command support	*/
+#undef CONFIG_CMD_XIMG		/* Load part of Multi Image	*/
+#undef CONFIG_CMD_NET
+
+//#define CONFIG_CMD_ASKENV
+//#define CONFIG_CMD_DHCP
+//#define CONFIG_CMD_PING
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_FAT
+/*#define CONFIG_CMD_UBI*/
+/*#define CONFIG_CMD_MTDPARTS*/
+//#define CONFIG_CMD_JFFS2
+//#define CONFIG_JFFS2_NAND
+//#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_UPDATE
+
+#define CONFIG_DOS_PARTITION
+
+/*#define CONFIG_MTD_PARTITIONS*/
+#define CONFIG_RBTREE
+
+#define CONFIG_BOOTP_MASK	( CONFIG_BOOTP_DEFAUL )
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#if 0
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+#define CONFIG_BOOTDELAY	0
+#define CONFIG_BOOTFILE	        uImage	/* file to load */
+#define CONFIG_BOOTARGS		"mem=64M console=ttyS0,57600n8 ip=off rootfstype=ubifs root=ubi:rootfs ubi.mtd=UBI rw panic=5 " MTDPARTS_DEFAULT
+#define CONFIG_BOOTCOMMAND	"check_and_update; setenv bootargs $bootargs $batt_level_param; ubi read 0x80600000 bootsplash && show_image 0x80600000; ubi read 0x80600000 kernel; bootm 0x80600000; ubi read 0x80600000 errorsplash && show_image 0x80600000; while test 0 = 0; do check_and_update; done"
+#define CONFIG_SYS_AUTOLOAD	"n"		/* No autoload */
+#define CONFIG_IPADDR		192.168.111.1
+#define CONFIG_SERVERIP		192.168.111.2
+#define MTDIDS_DEFAULT		"nand0=jz4740-nand"
+#define MTDPARTS_DEFAULT	"mtdparts=jz4740-nand:1M@0(uboot)ro,-@1M(UBI)"
+#define CONFIG_EXTRA_ENV_SETTINGS "mtdids=nand0=jz4740-nand\0mtdparts=mtdparts=jz4740-nand:1M@0(uboot)ro,-@1M(UBI)\0" \
+				"stdout=serial\0stderr=lcd\0"
+#endif
+
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAUL)
+#define CONFIG_BOOTDELAY	0
+#define CONFIG_BOOTFILE		"uImage"	/* file to load */
+#define CONFIG_BOOTARGS		"mem=64M console=ttyS0,57600n8 ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait"
+#define CONFIG_BOOTCOMMAND	"nand read 0x80600000 0x400000 0x200000;bootm"
+
+
+
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+
+/*
+ * Serial download configuration
+ *
+ */
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define	CONFIG_SYS_LONGHELP				/* undef to save memory      */
+#define	CONFIG_SYS_PROMPT		"n516 # "	/* Monitor Command Prompt    */
+#define	CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size   */
+#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)  /* Print Buffer Size */
+#define	CONFIG_SYS_MAXARGS		16		/* max number of command args*/
+
+#define CONFIG_SYS_MALLOC_LEN		1024*1024*2
+#define CONFIG_SYS_BOOTPARAMS_LEN	128*1024
+
+#define CONFIG_SYS_SDRAM_BASE		0x80000000     /* Cached addr */
+
+#define CONFIG_SYS_INIT_SP_OFFSET	0x400000
+
+#define	CONFIG_SYS_LOAD_ADDR		0x80600000     /* default load address	*/
+
+#define CONFIG_SYS_MEMTEST_START	0x80100000
+#define CONFIG_SYS_MEMTEST_END		0x80800000
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#define CONFIG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
+#else
+#define CONFIG_ENV_IS_IN_NAND	1	/* use NAND for environment vars	*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * NAND FLASH configuration
+ */
+#define CONFIG_SYS_MAX_NAND_DEVICE     1
+#define NAND_MAX_CHIPS          1
+#define CONFIG_SYS_NAND_BASE           0xB8000000
+#define CONFIG_SYS_NAND_SELECT_DEVICE  1       /* nand driver supports mutipl. chips   */
+
+/*
+ * IPL (Initial Program Loader, integrated inside CPU)
+ * Will load first 8k from NAND (SPL) into cache and execute it from there.
+ *
+ * SPL (Secondary Program Loader)
+ * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
+ * has to fit into 8kByte. It sets up the CPU and configures the SDRAM
+ * controller and the NAND controller so that the special U-Boot image can be
+ * loaded from NAND to SDRAM.
+ *
+ * NUB (NAND U-Boot)
+ * This NAND U-Boot (NUB) is a special U-Boot version which can be started
+ * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
+ *
+ */
+#define CONFIG_SYS_NAND_U_BOOT_DST	0x80100000	/* Load NUB to this addr	*/
+#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr	*/
+
+/*
+ * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
+ */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	(256 << 10)	/* Offset to RAM U-Boot image	*/
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	(512 << 10)	/* Size of RAM U-Boot image	*/
+
+#define CONFIG_SYS_NAND_PAGE_SIZE 2048
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 << 10)	/* NAND chip block size		*/
+#define CONFIG_SYS_NAND_BADBLOCK_PAGE	63		/* NAND bad block was marked at this page in a block, starting from 0 */
+#define CONFIG_SYS_NAND_ECC_POS		6
+
+#ifdef CONFIG_ENV_IS_IN_NAND
+//#define CONFIG_ENV_SIZE			CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_SIZE			(128 * 1024)
+//#define CONFIG_ENV_OFFSET		(CONFIG_SYS_NAND_BLOCK_SIZE + CONFIG_SYS_NAND_U_BOOT_SIZE + CONFIG_SYS_NAND_BLOCK_SIZE)	/* environment starts here  */
+#define CONFIG_ENV_OFFSET		(CONFIG_SYS_NAND_U_BOOT_SIZE + CONFIG_SYS_NAND_U_BOOT_OFFS)
+//#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#endif
+
+
+/*-----------------------------------------------------------------------
+ * NOR FLASH and environment organization
+ */
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	(128)	/* max number of sectors on one chip */
+
+#define PHYS_FLASH_1		0xa8000000 /* Flash Bank #1 */
+
+/* The following #defines are needed to get flash environment right */
+#define	CONFIG_SYS_MONITOR_BASE	TEXT_BASE   /* in pavo/config.mk TEXT_BASE=0x88000000*/ 
+#define	CONFIG_SYS_SYS_MONITOR_BASE	TEXT_BASE   /* in pavo/config.mk TEXT_BASE=0x88000000*/ 
+#define	CONFIG_SYS_MONITOR_LEN		(256*1024)  /* Reserve 256 kB for Monitor */
+
+#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_1
+
+/* timeout values are in ticks */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	(2 * CONFIG_SYS_HZ) /* Timeout for Flash Erase */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	(2 * CONFIG_SYS_HZ) /* Timeout for Flash Write */
+
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define	CONFIG_ENV_IS_NOWHERE	1
+#define CONFIG_ENV_ADDR		0xa8040000
+#define CONFIG_ENV_SIZE		0x20000
+#endif
+
+/*-----------------------------------------------------------------------
+ * SDRAM Info.
+ */
+#define CONFIG_NR_DRAM_BANKS	1
+
+// SDRAM paramters
+#define SDRAM_BW16		0	/* Data bus width: 0-32bit, 1-16bit */
+#define SDRAM_BANK4		1	/* Banks each chip: 0-2bank, 1-4bank */
+#define SDRAM_ROW		13	/* Row address: 11 to 13 */
+#define SDRAM_COL		9	/* Column address: 8 to 12 */
+#define SDRAM_CASL		2	/* CAS latency: 2 or 3 */
+
+// SDRAM Timings, unit: ns
+#define SDRAM_TRAS		45	/* RAS# Active Time */
+#define SDRAM_RCD		20	/* RAS# to CAS# Delay */
+#define SDRAM_TPC		20	/* RAS# Precharge Time */
+#define SDRAM_TRWL		7	/* Write Latency Time */
+#define SDRAM_TREF	        15625	/* Refresh period: 4096 refresh cycles/64ms */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CONFIG_SYS_DCACHE_SIZE		16384
+#define CONFIG_SYS_ICACHE_SIZE		16384
+#define CONFIG_SYS_CACHELINE_SIZE	32
+
+/*-----------------------------------------------------------------------
+ * GPIO definition
+ */
+#define GPIO_SD_VCC_EN_N	113 /* GPD17 */
+#define GPIO_SD_CD_N           103 /* GPD7 */
+#define GPIO_SD_WP             111 /* GPD15 */
+#define GPIO_USB_DETE          115 /* GPD6 */
+//#define GPIO_DC_DETE_N               103 /* GPD7 */
+#define GPIO_CHARG_STAT_N      112 /* GPD15 */
+#define GPIO_DISP_OFF_N                97 /* GPD1 */
+#define GPIO_UDC_HOTPLUG       100 /* GPD4 */
+#define GPIO_LED_EN            124 /* GPD28 */
+
+#define GPIO_RST_L          50   /* GPB18 LCD_SPL */
+#define GPIO_LCDRDY         49   /* GPB17 LCD_CLS */
+#define GPIO_STBY           86   /* GPC22 LCD_PS */
+#define GPIO_ERR            87   /* GPC23 LCD_REV */
+
+#endif	/* __CONFIG_H */

package/uboot-xburst/files/include/configs/nanonote.h

@@ -0,0 +1,191 @@
+/*
+ * Authors: Xiangfu Liu <xiangfu.z@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 3 of the License, or (at your option) any later version.
+ */
+
+/*
+ * This file contains the configuration parameters for the NanoNote.
+ */
+#ifndef __CONFIG_NANONOTE_H
+#define __CONFIG_NANONOTE_H
+
+#define CONFIG_MIPS32		1  /* MIPS32 CPU core */
+#define CONFIG_JzRISC		1  /* JzRISC core */
+#define CONFIG_JZSOC		1  /* Jz SoC */
+#define CONFIG_JZ4740		1  /* Jz4740 SoC */
+#define CONFIG_NANONOTE		1
+
+#define CONFIG_LCD		1  /* LCD support */
+#define LCD_BPP			LCD_COLOR32	/*5:18,24,32 bits per pixel */
+#define CONFIG_SYS_WHITE_ON_BLACK	1
+
+#define CONFIG_SYS_CPU_SPEED	336000000	/* CPU clock: 336 MHz */
+#define CONFIG_SYS_EXTAL		12000000	/* EXTAL freq: 12 MHz */
+#define CONFIG_SYS_HZ		(CONFIG_SYS_EXTAL / 256) /* incrementer freq */
+#define CONFIG_SYS_MIPS_TIMER_FREQ	CONFIG_SYS_CPU_SPEED
+
+#define CONFIG_SYS_UART_BASE	UART0_BASE	/* Base of the UART channel */
+#define CONFIG_BAUDRATE		57600
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+#define CONFIG_MMC      	1
+#define CONFIG_FAT      	1
+#define CONFIG_DOS_PARTITION	1
+#define CONFIG_SKIP_LOWLEVEL_INIT	1
+#define CONFIG_BOARD_EARLY_INIT_F	1
+#define CONFIG_SYS_NO_FLASH	1
+#define CONFIG_ENV_OVERWRITE	1
+
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAUL)
+#define CONFIG_BOOTDELAY	0
+#define CONFIG_BOOTFILE		"uImage"	/* file to load */
+/*
+ * Command line configuration.
+ */
+#define CONFIG_CMD_BOOTD	/* bootd			*/
+#define CONFIG_CMD_CONSOLE	/* coninfo			*/
+#define CONFIG_CMD_ECHO		/* echo arguments		*/
+
+#define CONFIG_CMD_LOADB	/* loadb			*/
+#define CONFIG_CMD_LOADS	/* loads			*/
+#define CONFIG_CMD_MEMORY	/* md mm nm mw cp cmp crc base loop mtest */
+#define CONFIG_CMD_MISC		/* Misc functions like sleep etc*/
+#define CONFIG_CMD_RUN		/* run command in env variable	*/
+#define CONFIG_CMD_SAVEENV	/* saveenv			*/
+#define CONFIG_CMD_SETGETDCR	/* DCR support on 4xx		*/
+#define CONFIG_CMD_SOURCE	/* "source" command support	*/
+
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_FAT
+
+/*
+ * Serial download configuration
+ */
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CONFIG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define	CONFIG_SYS_LONGHELP			/* undef to save memory */
+#define	CONFIG_SYS_PROMPT		"QI# "	/* Monitor Command Prompt */
+#define	CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
+#define	CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+/* Print Buffer Size */
+#define	CONFIG_SYS_MAXARGS		16	/* max number of command args*/
+
+#define CONFIG_SYS_MALLOC_LEN		896 * 1024
+#define CONFIG_SYS_BOOTPARAMS_LEN	128 * 1024
+
+#define CONFIG_SYS_SDRAM_BASE		0x80000000     /* Cached addr */
+#define CONFIG_SYS_INIT_SP_OFFSET	0x400000
+#define CONFIG_SYS_LOAD_ADDR		0x80600000     /* default load address */
+#define CONFIG_SYS_MEMTEST_START	0x80100000
+#define CONFIG_SYS_MEMTEST_END		0x80800000
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_IS_IN_NAND	1	/* use NAND for environment vars */
+
+/*
+ * NAND FLASH configuration
+ */
+/* NAND Boot config code */
+#define JZ4740_NANDBOOT_CFG	JZ4740_NANDBOOT_B8R3
+
+#define NANONOTE_NAND_SIZE	2 /* if board nand flash is 1GB, set to 1
+				   * if board nand flash is 2GB, set to 2
+				   * for change the PAGE_SIZE and BLOCK_SIZE
+				   * will delete when there is no 1GB flash
+				   */
+
+#define CONFIG_SYS_NAND_PAGE_SIZE	(2048 * NANONOTE_NAND_SIZE)
+/* nand chip block size	*/
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(256 * NANONOTE_NAND_SIZE << 10)
+/* nand bad block was marked at this page in a block, start from 0 */
+#define CONFIG_SYS_NAND_BADBLOCK_PAGE	127
+/* ECC offset position in oob area, default value is 6 if it isn't defined */
+#define CONFIG_SYS_NAND_ECC_POS	(6 * NANONOTE_NAND_SIZE)
+#define CONFIG_SYS_MAX_NAND_DEVICE     1
+#define NAND_MAX_CHIPS          1
+#define CONFIG_SYS_NAND_BASE           0xB8000000
+#define CONFIG_SYS_NAND_SELECT_DEVICE  1 /* nand driver supports mutipl.*/
+#define CONFIG_SYS_ONENAND_BASE	CONFIG_SYS_NAND_BASE
+
+/*
+ * IPL (Initial Program Loader, integrated inside CPU)
+ * Will load first 8k from NAND (SPL) into cache and execute it from there.
+ *
+ * SPL (Secondary Program Loader)
+ * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
+ * has to fit into 8kByte. It sets up the CPU and configures the SDRAM
+ * controller and the NAND controller so that the special U-Boot image can be
+ * loaded from NAND to SDRAM.
+ *
+ * NUB (NAND U-Boot)
+ * This NAND U-Boot (NUB) is a special U-Boot version which can be started
+ * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
+ *
+ */
+#define CONFIG_SYS_NAND_U_BOOT_DST		0x80100000	/* Load NUB to this addr */
+#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST 
+/* Start NUB from this addr*/
+
+/*
+ * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
+ */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	(256 << 10)	/* Offset to RAM U-Boot image */
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	(512 << 10)	/* Size of RAM U-Boot image */
+
+#define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET	(CONFIG_SYS_NAND_BLOCK_SIZE + CONFIG_SYS_NAND_U_BOOT_SIZE + CONFIG_SYS_NAND_BLOCK_SIZE)
+/* environment starts here  */
+#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+
+/* in board/nanonote/config.mk TEXT_BAS = 0x88000000 */
+#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE
+
+/*
+ * SDRAM Info.
+ */
+#define CONFIG_NR_DRAM_BANKS	1
+
+/*
+ * Cache Configuration
+ */
+#define CONFIG_SYS_DCACHE_SIZE	16384
+#define CONFIG_SYS_ICACHE_SIZE	16384
+#define CONFIG_SYS_CACHELINE_SIZE	32
+
+/*
+ * GPIO definition
+ */
+#define GPIO_LCD_CS	(2 * 32 + 21)
+#define GPIO_DISP_OFF_N (3 * 32 + 21)
+#define GPIO_PWM	(3 * 32 + 27)
+
+#define GPIO_AMP_EN	(3 * 32 + 4)
+
+#define GPIO_SDPW_EN	(3 * 32 + 2)
+#define	GPIO_SD_DETECT	(3 * 32 + 0)
+
+#define	GPIO_USB_DETECT	(3 * 32 + 27)
+#define	GPIO_BUZZ_PWM	(3 * 32 + 28)
+
+#define	GPIO_AUDIO_POP	(1 * 32 + 29)
+#define GPIO_COB_TEST	(1 * 32 + 30)
+
+#define	GPIO_KEYOUT_BASE	(2 * 32 + 10)
+#define	GPIO_KEYIN_BASE	(3 * 32 + 18)
+#define	GPIO_KEYIN_8	(3 * 32 + 26)
+
+#define GPIO_SD_CD_N	GPIO_SD_DETECT		/* SD Card insert detect */
+#define GPIO_SD_VCC_EN_N	GPIO_SDPW_EN	/* SD Card Power Enable */
+
+#endif	/* __CONFIG_NANONOTE_H */

package/uboot-xburst/files/include/configs/qi_lb60.h

@@ -0,0 +1,27 @@
+#ifndef __CONFIG_QI_LB60_H
+#define __CONFIG_QI_LB60_H
+
+#include <configs/nanonote.h>
+
+#define CONFIG_QI_LB60 1
+
+#define CONFIG_BOOTARGS		"mem=32M console=ttyS0,57600n8 ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait"
+#define CONFIG_BOOTARGSFROMSD	"mem=32M console=ttyS0,57600n8 rootfstype=ext2 root=/dev/mmcblk0p2 rw rootwait"
+#define CONFIG_BOOTCOMMAND	"nand read 0x80600000 0x400000 0x200000;bootm"
+#define CONFIG_BOOTCOMMANDFROMSD	"mmc init; fatload mmc 0 0x80600000 uImage; bootm"
+
+/* SDRAM paramters */
+#define SDRAM_BW16		1	/* Data bus width: 0-32bit, 1-16bit */
+#define SDRAM_BANK4		1	/* Banks each chip: 0-2bank, 1-4bank */
+#define SDRAM_ROW		13	/* Row address: 11 to 13 */
+#define SDRAM_COL		9	/* Column address: 8 to 12 */
+#define SDRAM_CASL		2	/* CAS latency: 2 or 3 */
+
+/* SDRAM Timings, unit: ns */
+#define SDRAM_TRAS		45	/* RAS# Active Time */
+#define SDRAM_RCD		20	/* RAS# to CAS# Delay */
+#define SDRAM_TPC		20	/* RAS# Precharge Time */
+#define SDRAM_TRWL		7	/* Write Latency Time */
+#define SDRAM_TREF	        15625	/* Refresh period: 8192 cycles/64ms */
+
+#endif

package/uboot-xburst/files/include/configs/sakc.h

@@ -0,0 +1,200 @@
+/*
+ * Authors: Xiangfu Liu <xiangfu.z@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 3 of the License, or (at your option) any later version.
+ */
+
+/*
+ * This file contains the configuration parameters for SAKC.
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define DEBUG
+#define CONFIG_MIPS32		1  /* MIPS32 CPU core */
+#define CONFIG_JzRISC		1  /* JzRISC core */
+#define CONFIG_JZSOC		1  /* Jz SoC */
+#define CONFIG_JZ4725		1  /* Jz4725 SoC */
+#define CONFIG_JZ4740		1  /* Jz4740 SoC */
+#define CONFIG_SAKC			1  /* SAKC board */
+
+#define MMC_BUS_WIDTH_1BIT	1  /* 1 for MMC  1Bit Bus Width */
+
+//#define CONFIG_LCD		1  /* LCD support */
+//#define LCD_BPP			LCD_COLOR32	/*5:18,24,32 bits per pixel */
+//#define CONFIG_SYS_WHITE_ON_BLACK	1
+
+#define CONFIG_SYS_CPU_SPEED	336000000	/* CPU clock: 336 MHz */
+#define CONFIG_SYS_EXTAL		12000000	/* EXTAL freq: 12 MHz */
+#define CONFIG_SYS_HZ		(CONFIG_SYS_EXTAL / 256) /* incrementer freq */
+#define CONFIG_SYS_MIPS_TIMER_FREQ	CONFIG_SYS_CPU_SPEED
+
+#define CONFIG_SYS_UART_BASE	UART0_BASE	/* Base of the UART channel */
+#define CONFIG_BAUDRATE		57600
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+#define CONFIG_MMC      	1
+#define CONFIG_FAT      	1  
+#define CONFIG_DOS_PARTITION	1
+#define CONFIG_SKIP_LOWLEVEL_INIT	1
+#define CONFIG_BOARD_EARLY_INIT_F	1
+#define CONFIG_SYS_NO_FLASH	1
+#define CONFIG_ENV_OVERWRITE	1
+
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAUL)
+#define CONFIG_BOOTDELAY	3
+#define CONFIG_BOOTFILE		"uImage"	/* file to load */
+#define CONFIG_BOOTARGS		"mem=32M console=ttyS0,57600n8 ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait"
+#define CONFIG_EXTRA_ENV_SETTINGS	1
+#define CONFIG_BOOTARGSFROMSD	"mem=32M console=ttyS0,57600n8 rootfstype=ext2 root=/dev/mmcblk0p1 rw rootwait"
+#define CONFIG_BOOTCOMMAND	"nand read 0x80600000 0x400000 0x200000;bootm"
+
+/*
+ * Command line configuration.
+ */
+#define CONFIG_CMD_BDI		/* bdinfo			*/
+#define CONFIG_CMD_BOOTD	/* bootd			*/
+#define CONFIG_CMD_CONSOLE	/* coninfo			*/
+#define CONFIG_CMD_ECHO		/* echo arguments		*/
+#define CONFIG_CMD_IMI		/* iminfo			*/
+#define CONFIG_CMD_ITEST	/* Integer (and string) test	*/
+
+#define CONFIG_CMD_LOADB	/* loadb			*/
+#define CONFIG_CMD_LOADS	/* loads			*/
+#define CONFIG_CMD_MEMORY	/* md mm nm mw cp cmp crc base loop mtest */
+#define CONFIG_CMD_MISC		/* Misc functions like sleep etc*/
+#define CONFIG_CMD_RUN		/* run command in env variable	*/
+#define CONFIG_CMD_SAVEENV	/* saveenv			*/
+#define CONFIG_CMD_SETGETDCR	/* DCR support on 4xx		*/
+#define CONFIG_CMD_SOURCE	/* "source" command support	*/
+#define CONFIG_CMD_XIMG		/* Load part of Multi Image	*/
+
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_FAT
+
+/*
+ * Serial download configuration
+ */
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CONFIG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define	CONFIG_SYS_LONGHELP			/* undef to save memory */
+#define	CONFIG_SYS_PROMPT		"SAKC# "	/* Monitor Command Prompt */
+#define	CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
+#define	CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+/* Print Buffer Size */
+#define	CONFIG_SYS_MAXARGS		16	/* max number of command args*/
+
+#define CONFIG_SYS_MALLOC_LEN		128 * 1024
+#define CONFIG_SYS_BOOTPARAMS_LEN	128 * 1024
+
+#define CONFIG_SYS_SDRAM_BASE		0x80000000     /* Cached addr */
+#define CONFIG_SYS_INIT_SP_OFFSET	0x400000
+#define CONFIG_SYS_LOAD_ADDR		0x80600000     /* default load address */
+#define CONFIG_SYS_MEMTEST_START	0x80100000
+#define CONFIG_SYS_MEMTEST_END		0x80800000
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_IS_IN_NAND	1	/* use NAND for environment vars */
+
+/*
+ * NAND FLASH configuration
+ */
+/* NAND Boot config code */
+#define JZ4740_NANDBOOT_CFG	JZ4740_NANDBOOT_B8R3 
+
+#define SAKC_NAND_SIZE	1 /* if board nand flash is 1GB, set to 1
+				   * if board nand flash is 2GB, set to 2
+				   * for change the PAGE_SIZE and BLOCK_SIZE
+				   * will delete when there is no 1GB flash
+				   */
+
+#define CONFIG_SYS_NAND_PAGE_SIZE	(2048 * SAKC_NAND_SIZE)
+/* nand chip block size	*/
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(256 * SAKC_NAND_SIZE << 10)	
+/* nand bad block was marked at this page in a block, start from 0 */
+#define CONFIG_SYS_NAND_BADBLOCK_PAGE	127 
+/* ECC offset position in oob area, default value is 6 if it isn't defined */
+#define CONFIG_SYS_NAND_ECC_POS	(6 * SAKC_NAND_SIZE)
+#define CONFIG_SYS_MAX_NAND_DEVICE     1
+#define NAND_MAX_CHIPS          1
+#define CONFIG_SYS_NAND_BASE           0xB8000000
+#define CONFIG_SYS_NAND_SELECT_DEVICE  1 /* nand driver supports mutipl.*/
+#define CONFIG_SYS_ONENAND_BASE	CONFIG_SYS_NAND_BASE
+
+/*
+ * IPL (Initial Program Loader, integrated inside CPU)
+ * Will load first 8k from NAND (SPL) into cache and execute it from there.
+ *
+ * SPL (Secondary Program Loader)
+ * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
+ * has to fit into 8kByte. It sets up the CPU and configures the SDRAM
+ * controller and the NAND controller so that the special U-Boot image can be
+ * loaded from NAND to SDRAM.
+ *
+ * NUB (NAND U-Boot)
+ * This NAND U-Boot (NUB) is a special U-Boot version which can be started
+ * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
+ *
+ */
+#define CONFIG_SYS_NAND_U_BOOT_DST		0x80100000	/* Load NUB to this addr */
+#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST 
+/* Start NUB from this addr*/
+
+/*
+ * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
+ */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	(256 << 10)	/* Offset to RAM U-Boot image */
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	(512 << 10)	/* Size of RAM U-Boot image */
+
+#define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET	(CONFIG_SYS_NAND_BLOCK_SIZE + CONFIG_SYS_NAND_U_BOOT_SIZE + CONFIG_SYS_NAND_BLOCK_SIZE)
+/* environment starts here  */
+#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+
+/* in qi_lb60.h/config.mk TEXT_BAS = 0x88000000 */
+#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE
+
+/*
+ * SDRAM Info.
+ */
+#define CONFIG_NR_DRAM_BANKS	1
+
+/* SDRAM paramters */
+#define SDRAM_BW16		1	/* Data bus width: 0-32bit, 1-16bit */
+#define SDRAM_BANK4		1	/* Banks each chip: 0-2bank, 1-4bank */
+#define SDRAM_ROW		13	/* Row address: 11 to 13 */
+#define SDRAM_COL		9	/* Column address: 8 to 12 */
+#define SDRAM_CASL		2	/* CAS latency: 2 or 3 */
+
+/* SDRAM Timings, unit: ns */
+#define SDRAM_TRAS		45	/* RAS# Active Time */
+#define SDRAM_RCD		20	/* RAS# to CAS# Delay */
+#define SDRAM_TPC		20	/* RAS# Precharge Time */
+#define SDRAM_TRWL		7	/* Write Latency Time */
+#define SDRAM_TREF	        15625	/* Refresh period: 8192 cycles/64ms */
+
+/*
+ * Cache Configuration
+ */
+#define CONFIG_SYS_DCACHE_SIZE	16384
+#define CONFIG_SYS_ICACHE_SIZE	16384
+#define CONFIG_SYS_CACHELINE_SIZE	32
+
+/*
+ * GPIO definition
+ */  
+#define	GPIO_SD_DETECT		(2 * 32 + 27)
+#define GPIO_SD_CD_N		GPIO_SD_DETECT	/* SD Card insert detect */
+#define GPIO_SD_VCC_EN_N	GPIO_SDPW_EN	/* SD Card Power Enable */
+
+#endif	/* __CONFIG_H */

package/uboot-xburst/files/nand_spl/board/n516/Makefile

@@ -0,0 +1,104 @@
+#
+# (C) Copyright 2006
+# Stefan Roese, DENX Software Engineering, sr@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+include $(TOPDIR)/nand_spl/board/$(BOARDDIR)/config.mk
+
+LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds
+LDFLAGS	= -Bstatic -T $(LDSCRIPT) -Ttext $(TEXT_BASE)
+AFLAGS	+= -DCONFIG_NAND_SPL
+CFLAGS	+= -DCONFIG_NAND_SPL
+
+SOBJS	= start.o usb_boot.o
+COBJS	= nand_boot_jz4740.o cpu.o jz4740.o jz_serial.o
+
+SRCS	:= $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c))
+OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS))
+__OBJS	:= $(SOBJS) $(COBJS)
+LNDIR	:= $(OBJTREE)/nand_spl/board/$(BOARDDIR)
+
+nandobj	:= $(OBJTREE)/nand_spl/
+
+ALL	= $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin
+all:	$(obj).depend $(ALL)
+
+$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl.bin
+	dd bs=1024 count=8 if=/dev/zero of=$(nandobj)junk1
+	cat $< $(nandobj)junk1 > $(nandobj)junk2
+	dd bs=1024 count=8 if=$(nandobj)junk2 of=$(nandobj)junk3
+	cat $(nandobj)junk3 $(nandobj)junk3 > $(nandobj)junk4
+	dd bs=1024 count=256 if=/dev/zero of=$(nandobj)junk5
+	cat $(nandobj)junk4 $(nandobj)junk5 > $(nandobj)junk6
+	dd bs=1024 count=256 if=$(nandobj)junk6 of=$@
+	rm -f $(nandobj)junk*
+
+$(nandobj)u-boot-spl.bin:	$(nandobj)u-boot-spl
+	$(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
+
+$(nandobj)u-boot-spl:	$(OBJS)
+	cd $(LNDIR) && $(LD) $(LDFLAGS) $$UNDEF_SYM $(__OBJS) \
+		-Map $(nandobj)u-boot-spl.map \
+		-o $(nandobj)u-boot-spl
+
+# create symbolic links for common files
+
+# from cpu directory
+$(obj)start.S:
+	@rm -f $(obj)start.S
+	ln -s $(SRCTREE)/cpu/mips/start.S $(obj)start.S
+
+$(obj)usb_boot.S:
+	@rm -f $(obj)usb_boot.S
+	ln -s $(SRCTREE)/cpu/mips/usb_boot.S $(obj)usb_boot.S
+
+$(obj)cpu.c:
+	@rm -f $(obj)cpu.c
+	ln -s $(SRCTREE)/cpu/mips/cpu.c $(obj)cpu.c
+
+$(obj)jz4740.c:
+	@rm -f $(obj)jz4740.c
+	ln -s $(SRCTREE)/cpu/mips/jz4740.c $(obj)jz4740.c
+
+$(obj)jz_serial.c:
+	@rm -f $(obj)jz_serial.c
+	ln -s $(SRCTREE)/cpu/mips/jz_serial.c $(obj)jz_serial.c
+
+# from nand_spl directory
+$(obj)nand_boot_jz4740.c:
+	@rm -f $(obj)nand_boot_jz4740.c
+	ln -s $(SRCTREE)/nand_spl/nand_boot_jz4740.c $(obj)nand_boot_jz4740.c
+
+#########################################################################
+
+$(obj)%.o:	$(obj)%.S
+	$(CC) $(AFLAGS) -c -o $@ $<
+
+$(obj)%.o:	$(obj)%.c
+	$(CC) $(CFLAGS) -c -o $@ $<
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################

package/uboot-xburst/files/nand_spl/board/n516/config.mk

@@ -0,0 +1,34 @@
+#
+# (C) Copyright 2006
+# Stefan Roese, DENX Software Engineering, sr@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+#
+# Ingenic JZ4740 Reference Platform
+#
+
+#
+# TEXT_BASE for SPL:
+#
+# On JZ4730 platforms the SPL is located at 0x80000000...0x80001000,
+# in the first 4kBytes of memory space in cache. So we set
+# TEXT_BASE to starting address in internal cache here.
+#
+TEXT_BASE = 0x80000000

package/uboot-xburst/files/nand_spl/board/n516/u-boot.lds

@@ -0,0 +1,63 @@
+/*
+ * (C) Copyright 2005
+ * Ingenic Semiconductor, <jlwei@ingenic.cn>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-tradlittlemips", "elf32-tradlittlemips", "elf32-tradlittlemips")
+
+OUTPUT_ARCH(mips)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text       :
+	{
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata  : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data  : { *(.data) }
+
+	. = ALIGN(4);
+	.sdata  : { *(.sdata) }
+
+	_gp = ALIGN(16);
+
+	__got_start = .;
+	.got  : { *(.got) }
+	__got_end = .;
+
+	.sdata  : { *(.sdata) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	uboot_end_data = .;
+	num_got_entries = (__got_end - __got_start) >> 2;
+
+	. = ALIGN(4);
+	.sbss  : { *(.sbss) }
+	.bss  : { *(.bss) }
+	uboot_end = .;
+}

package/uboot-xburst/files/nand_spl/board/nanonote/Makefile

@@ -0,0 +1,104 @@
+#
+# (C) Copyright 2006
+# Stefan Roese, DENX Software Engineering, sr@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+include $(TOPDIR)/nand_spl/board/$(BOARDDIR)/config.mk
+
+LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds
+LDFLAGS	= -Bstatic -T $(LDSCRIPT) -Ttext $(TEXT_BASE)
+AFLAGS	+= -DCONFIG_NAND_SPL
+CFLAGS	+= -DCONFIG_NAND_SPL
+
+SOBJS	= start.o usb_boot.o
+COBJS	= nand_boot_jz4740.o cpu.o jz4740.o jz_serial.o
+
+SRCS	:= $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c))
+OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS))
+__OBJS	:= $(SOBJS) $(COBJS)
+LNDIR	:= $(OBJTREE)/nand_spl/board/$(BOARDDIR)
+
+nandobj	:= $(OBJTREE)/nand_spl/
+
+ALL	= $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin
+all:	$(obj).depend $(ALL)
+
+$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl.bin
+	dd bs=1024 count=8 if=/dev/zero of=$(nandobj)junk1
+	cat $< $(nandobj)junk1 > $(nandobj)junk2
+	dd bs=1024 count=8 if=$(nandobj)junk2 of=$(nandobj)junk3
+	cat $(nandobj)junk3 $(nandobj)junk3 > $(nandobj)junk4
+	dd bs=1024 count=256 if=/dev/zero of=$(nandobj)junk5
+	cat $(nandobj)junk4 $(nandobj)junk5 > $(nandobj)junk6
+	dd bs=1024 count=256 if=$(nandobj)junk6 of=$@
+	rm -f $(nandobj)junk*
+
+$(nandobj)u-boot-spl.bin:	$(nandobj)u-boot-spl
+	$(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
+
+$(nandobj)u-boot-spl:	$(OBJS)
+	cd $(LNDIR) && $(LD) $(LDFLAGS) $$UNDEF_SYM $(__OBJS) \
+		-Map $(nandobj)u-boot-spl.map \
+		-o $(nandobj)u-boot-spl
+
+# create symbolic links for common files
+
+# from cpu directory
+$(obj)start.S:
+	@rm -f $(obj)start.S
+	ln -s $(SRCTREE)/cpu/mips/start.S $(obj)start.S
+
+$(obj)usb_boot.S:
+	@rm -f $(obj)usb_boot.S
+	ln -s $(SRCTREE)/cpu/mips/usb_boot.S $(obj)usb_boot.S
+
+$(obj)cpu.c:
+	@rm -f $(obj)cpu.c
+	ln -s $(SRCTREE)/cpu/mips/cpu.c $(obj)cpu.c
+
+$(obj)jz4740.c:
+	@rm -f $(obj)jz4740.c
+	ln -s $(SRCTREE)/cpu/mips/jz4740.c $(obj)jz4740.c
+
+$(obj)jz_serial.c:
+	@rm -f $(obj)jz_serial.c
+	ln -s $(SRCTREE)/cpu/mips/jz_serial.c $(obj)jz_serial.c
+
+# from nand_spl directory
+$(obj)nand_boot_jz4740.c:
+	@rm -f $(obj)nand_boot_jz4740.c
+	ln -s $(SRCTREE)/nand_spl/nand_boot_jz4740.c $(obj)nand_boot_jz4740.c
+
+#########################################################################
+
+$(obj)%.o:	$(obj)%.S
+	$(CC) $(AFLAGS) -c -o $@ $<
+
+$(obj)%.o:	$(obj)%.c
+	$(CC) $(CFLAGS) -c -o $@ $<
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################

package/uboot-xburst/files/nand_spl/board/nanonote/config.mk

@@ -0,0 +1,34 @@
+#
+# (C) Copyright 2006
+# Stefan Roese, DENX Software Engineering, sr@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+#
+# Ingenic JZ4740 Reference Platform
+#
+
+#
+# TEXT_BASE for SPL:
+#
+# On JZ4730 platforms the SPL is located at 0x80000000...0x80001000,
+# in the first 4kBytes of memory space in cache. So we set
+# TEXT_BASE to starting address in internal cache here.
+#
+TEXT_BASE = 0x80000000

package/uboot-xburst/files/nand_spl/board/nanonote/u-boot.lds

@@ -0,0 +1,63 @@
+/*
+ * (C) Copyright 2005
+ * Ingenic Semiconductor, <jlwei@ingenic.cn>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-tradlittlemips", "elf32-tradlittlemips", "elf32-tradlittlemips")
+
+OUTPUT_ARCH(mips)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text       :
+	{
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata  : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data  : { *(.data) }
+
+	. = ALIGN(4);
+	.sdata  : { *(.sdata) }
+
+	_gp = ALIGN(16);
+
+	__got_start = .;
+	.got  : { *(.got) }
+	__got_end = .;
+
+	.sdata  : { *(.sdata) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	uboot_end_data = .;
+	num_got_entries = (__got_end - __got_start) >> 2;
+
+	. = ALIGN(4);
+	.sbss  : { *(.sbss) }
+	.bss  : { *(.bss) }
+	uboot_end = .;
+}

package/uboot-xburst/files/nand_spl/board/sakc/Makefile

@@ -0,0 +1,104 @@
+#
+# (C) Copyright 2006
+# Stefan Roese, DENX Software Engineering, sr@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+include $(TOPDIR)/nand_spl/board/$(BOARDDIR)/config.mk
+
+LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds
+LDFLAGS	= -Bstatic -T $(LDSCRIPT) -Ttext $(TEXT_BASE)
+AFLAGS	+= -DCONFIG_NAND_SPL
+CFLAGS	+= -DCONFIG_NAND_SPL
+
+SOBJS	= start.o usb_boot.o
+COBJS	= nand_boot_jz4740.o cpu.o jz4740.o jz_serial.o
+
+SRCS	:= $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c))
+OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS))
+__OBJS	:= $(SOBJS) $(COBJS)
+LNDIR	:= $(OBJTREE)/nand_spl/board/$(BOARDDIR)
+
+nandobj	:= $(OBJTREE)/nand_spl/
+
+ALL	= $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin
+all:	$(obj).depend $(ALL)
+
+$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl.bin
+	dd bs=1024 count=8 if=/dev/zero of=$(nandobj)junk1
+	cat $< $(nandobj)junk1 > $(nandobj)junk2
+	dd bs=1024 count=8 if=$(nandobj)junk2 of=$(nandobj)junk3
+	cat $(nandobj)junk3 $(nandobj)junk3 > $(nandobj)junk4
+	dd bs=1024 count=256 if=/dev/zero of=$(nandobj)junk5
+	cat $(nandobj)junk4 $(nandobj)junk5 > $(nandobj)junk6
+	dd bs=1024 count=256 if=$(nandobj)junk6 of=$@
+	rm -f $(nandobj)junk*
+
+$(nandobj)u-boot-spl.bin:	$(nandobj)u-boot-spl
+	$(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
+
+$(nandobj)u-boot-spl:	$(OBJS)
+	cd $(LNDIR) && $(LD) $(LDFLAGS) $$UNDEF_SYM $(__OBJS) \
+		-Map $(nandobj)u-boot-spl.map \
+		-o $(nandobj)u-boot-spl
+
+# create symbolic links for common files
+
+# from cpu directory
+$(obj)start.S:
+	@rm -f $(obj)start.S
+	ln -s $(SRCTREE)/cpu/mips/start.S $(obj)start.S
+
+$(obj)usb_boot.S:
+	@rm -f $(obj)usb_boot.S
+	ln -s $(SRCTREE)/cpu/mips/usb_boot.S $(obj)usb_boot.S
+
+$(obj)cpu.c:
+	@rm -f $(obj)cpu.c
+	ln -s $(SRCTREE)/cpu/mips/cpu.c $(obj)cpu.c
+
+$(obj)jz4740.c:
+	@rm -f $(obj)jz4740.c
+	ln -s $(SRCTREE)/cpu/mips/jz4740.c $(obj)jz4740.c
+
+$(obj)jz_serial.c:
+	@rm -f $(obj)jz_serial.c
+	ln -s $(SRCTREE)/cpu/mips/jz_serial.c $(obj)jz_serial.c
+
+# from nand_spl directory
+$(obj)nand_boot_jz4740.c:
+	@rm -f $(obj)nand_boot_jz4740.c
+	ln -s $(SRCTREE)/nand_spl/nand_boot_jz4740.c $(obj)nand_boot_jz4740.c
+
+#########################################################################
+
+$(obj)%.o:	$(obj)%.S
+	$(CC) $(AFLAGS) -c -o $@ $<
+
+$(obj)%.o:	$(obj)%.c
+	$(CC) $(CFLAGS) -c -o $@ $<
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################

package/uboot-xburst/files/nand_spl/board/sakc/config.mk

@@ -0,0 +1,34 @@
+#
+# (C) Copyright 2006
+# Stefan Roese, DENX Software Engineering, sr@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+#
+# Ingenic JZ4740 Reference Platform
+#
+
+#
+# TEXT_BASE for SPL:
+#
+# On JZ4730 platforms the SPL is located at 0x80000000...0x80001000,
+# in the first 4kBytes of memory space in cache. So we set
+# TEXT_BASE to starting address in internal cache here.
+#
+TEXT_BASE = 0x80000000

package/uboot-xburst/files/nand_spl/board/sakc/u-boot.lds

@@ -0,0 +1,63 @@
+/*
+ * (C) Copyright 2005
+ * Ingenic Semiconductor, <jlwei@ingenic.cn>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-tradlittlemips", "elf32-tradlittlemips", "elf32-tradlittlemips")
+
+OUTPUT_ARCH(mips)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text       :
+	{
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata  : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data  : { *(.data) }
+
+	. = ALIGN(4);
+	.sdata  : { *(.sdata) }
+
+	_gp = ALIGN(16);
+
+	__got_start = .;
+	.got  : { *(.got) }
+	__got_end = .;
+
+	.sdata  : { *(.sdata) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	uboot_end_data = .;
+	num_got_entries = (__got_end - __got_start) >> 2;
+
+	. = ALIGN(4);
+	.sbss  : { *(.sbss) }
+	.bss  : { *(.bss) }
+	uboot_end = .;
+}

package/uboot-xburst/files/nand_spl/nand_boot_jz4740.c

@@ -0,0 +1,429 @@
+/*
+ * Copyright (C) 2007 Ingenic Semiconductor Inc.
+ * Author: Peter <jlwei@ingenic.cn>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <nand.h>
+
+#include <asm/io.h>
+#include <asm/jz4740.h>
+
+#define KEY_U_OUT       (32 * 2 + 16)
+#define KEY_U_IN        (32 * 3 + 19)
+
+/*
+ * NAND flash definitions
+ */
+
+#define NAND_DATAPORT	0xb8000000
+#define NAND_ADDRPORT	0xb8010000
+#define NAND_COMMPORT	0xb8008000
+
+#define ECC_BLOCK	512
+#define ECC_POS		6
+#define PAR_SIZE	9
+
+#define __nand_enable()		(REG_EMC_NFCSR |= EMC_NFCSR_NFE1 | EMC_NFCSR_NFCE1)
+#define __nand_disable()	(REG_EMC_NFCSR &= ~(EMC_NFCSR_NFCE1))
+#define __nand_ecc_rs_encoding() \
+	(REG_EMC_NFECR = EMC_NFECR_ECCE | EMC_NFECR_ERST | EMC_NFECR_RS | EMC_NFECR_RS_ENCODING)
+#define __nand_ecc_rs_decoding() \
+	(REG_EMC_NFECR = EMC_NFECR_ECCE | EMC_NFECR_ERST | EMC_NFECR_RS | EMC_NFECR_RS_DECODING)
+#define __nand_ecc_disable()	(REG_EMC_NFECR &= ~EMC_NFECR_ECCE)
+#define __nand_ecc_encode_sync() while (!(REG_EMC_NFINTS & EMC_NFINTS_ENCF))
+#define __nand_ecc_decode_sync() while (!(REG_EMC_NFINTS & EMC_NFINTS_DECF))
+
+static inline void __nand_dev_ready(void)
+{
+	unsigned int timeout = 10000;
+	while ((REG_GPIO_PXPIN(2) & 0x40000000) && timeout--);
+	while (!(REG_GPIO_PXPIN(2) & 0x40000000));
+}
+
+#define __nand_cmd(n)		(REG8(NAND_COMMPORT) = (n))
+#define __nand_addr(n)		(REG8(NAND_ADDRPORT) = (n))
+#define __nand_data8()		REG8(NAND_DATAPORT)
+#define __nand_data16()		REG16(NAND_DATAPORT)
+
+#if (JZ4740_NANDBOOT_CFG == JZ4740_NANDBOOT_B8R3)
+	#define NAND_BUS_WIDTH 8
+	#define NAND_ROW_CYCLE 3
+#elif (JZ4740_NANDBOOT_CFG == JZ4740_NANDBOOT_B8R2)
+	#define NAND_BUS_WIDTH 8
+	#define NAND_ROW_CYCLE 2
+#elif (JZ4740_NANDBOOT_CFG == JZ4740_NANDBOOT_B16R3)
+	#define NAND_BUS_WIDTH 16
+	#define NAND_ROW_CYCLE 3
+#elif (JZ4740_NANDBOOT_CFG == JZ4740_NANDBOOT_B16R2)
+	#define NAND_BUS_WIDTH 16
+	#define NAND_ROW_CYCLE 2
+#endif
+
+/*
+ * NAND flash parameters
+ */
+static int page_size = 2048;
+static int oob_size = 64;
+static int ecc_count = 4;
+static int page_per_block = 64;
+static int bad_block_pos = 0;
+static int block_size = 131072;
+
+static unsigned char oob_buf[128] = {0};
+
+/*
+ * External routines
+ */
+extern void flush_cache_all(void);
+extern int serial_init(void);
+extern void serial_puts(const char *s);
+extern void sdram_init(void);
+extern void pll_init(void);
+extern void usb_boot();
+
+/*
+ * NAND flash routines
+ */
+#if NAND_BUS_WIDTH == 16
+static inline void nand_read_buf16(void *buf, int count)
+{
+	int i;
+	u16 *p = (u16 *)buf;
+
+	for (i = 0; i < count; i += 2)
+		*p++ = __nand_data16();
+}
+#define nand_read_buf nand_read_buf16
+
+#elif NAND_BUS_WIDTH == 8
+static inline void nand_read_buf8(void *buf, int count)
+{
+	int i;
+	u8 *p = (u8 *)buf;
+
+	for (i = 0; i < count; i++)
+		*p++ = __nand_data8();
+}
+#define nand_read_buf nand_read_buf8
+
+#endif
+
+/* Correct 1~9-bit errors in 512-bytes data */
+static void rs_correct(unsigned char *dat, int idx, int mask)
+{
+	int i;
+
+	idx--;
+
+	i = idx + (idx >> 3);
+	if (i >= 512)
+		return;
+
+	mask <<= (idx & 0x7);
+
+	dat[i] ^= mask & 0xff;
+	if (i < 511)
+		dat[i+1] ^= (mask >> 8) & 0xff;
+}
+
+static int nand_read_oob(int page_addr, uchar *buf, int size)
+{
+	int col_addr;
+	if (page_size != 512)
+		col_addr = page_size;
+	else {
+		col_addr = 0;
+		__nand_dev_ready();
+	}
+
+	if (page_size != 512)
+		/* Send READ0 command */
+		__nand_cmd(NAND_CMD_READ0);
+	else
+		/* Send READOOB command */
+		__nand_cmd(NAND_CMD_READOOB);
+
+	/* Send column address */
+	__nand_addr(col_addr & 0xff);
+	if (page_size != 512)
+		__nand_addr((col_addr >> 8) & 0xff);
+
+	/* Send page address */
+	__nand_addr(page_addr & 0xff);
+	__nand_addr((page_addr >> 8) & 0xff);
+	#ifdef NAND_ROW_CYCLE == 3
+		__nand_addr((page_addr >> 16) & 0xff);
+	#endif
+
+	/* Send READSTART command for 2048 or 4096 ps NAND */
+	if (page_size != 512)
+		__nand_cmd(NAND_CMD_READSTART);
+
+	/* Wait for device ready */
+	__nand_dev_ready();
+
+	/* Read oob data */
+	nand_read_buf(buf, size);
+	if (page_size == 512)
+		__nand_dev_ready();
+	return 0;
+}
+
+static int nand_read_page(int page_addr, uchar *dst, uchar *oobbuf)
+{
+	uchar *databuf = dst, *tmpbuf;
+	int i, j;
+
+	/*
+	 * Read oob data
+	 */
+	nand_read_oob(page_addr, oobbuf, oob_size);
+
+	/*
+	 * Read page data
+	 */
+
+	/* Send READ0 command */
+	__nand_cmd(NAND_CMD_READ0);
+
+	/* Send column address */
+	__nand_addr(0);
+	if (page_size != 512)
+		__nand_addr(0);
+
+	/* Send page address */
+	__nand_addr(page_addr & 0xff);
+	__nand_addr((page_addr >> 8) & 0xff);
+	#if NAND_ROW_CYCLE == 3
+		__nand_addr((page_addr >> 16) & 0xff);
+	#endif
+
+	/* Send READSTART command for 2048 or 4096 ps NAND */
+	if (page_size != 512)
+		__nand_cmd(NAND_CMD_READSTART);
+
+	/* Wait for device ready */
+	__nand_dev_ready();
+
+	/* Read page data */
+	tmpbuf = databuf;
+
+	for (i = 0; i < ecc_count; i++) {
+		volatile unsigned char *paraddr = (volatile unsigned char *)EMC_NFPAR0;
+		unsigned int stat;
+
+		/* Enable RS decoding */
+		REG_EMC_NFINTS = 0x0;
+		__nand_ecc_rs_decoding();
+
+		/* Read data */
+		nand_read_buf((void *)tmpbuf, ECC_BLOCK);
+
+		/* Set PAR values */
+		for (j = 0; j < PAR_SIZE; j++) {
+#if defined(CONFIG_SYS_NAND_ECC_POS)
+			*paraddr++ = oobbuf[CONFIG_SYS_NAND_ECC_POS + i*PAR_SIZE + j];
+#else
+			*paraddr++ = oobbuf[ECC_POS + i*PAR_SIZE + j];
+#endif
+		}
+
+		/* Set PRDY */
+		REG_EMC_NFECR |= EMC_NFECR_PRDY;
+
+		/* Wait for completion */
+		__nand_ecc_decode_sync();
+
+		/* Disable decoding */
+		__nand_ecc_disable();
+
+		/* Check result of decoding */
+		stat = REG_EMC_NFINTS;
+		if (stat & EMC_NFINTS_ERR) {
+			/* Error occurred */
+			/* serial_puts("\n Error occurred\n"); */
+			if (stat & EMC_NFINTS_UNCOR) {
+				/* Uncorrectable error occurred */
+				/* serial_puts("\nUncorrectable error occurred\n"); */
+			}
+			else {
+				unsigned int errcnt, index, mask;
+
+				errcnt = (stat & EMC_NFINTS_ERRCNT_MASK) >> EMC_NFINTS_ERRCNT_BIT;
+				switch (errcnt) {
+				case 4:
+					index = (REG_EMC_NFERR3 & EMC_NFERR_INDEX_MASK) >> EMC_NFERR_INDEX_BIT;
+					mask = (REG_EMC_NFERR3 & EMC_NFERR_MASK_MASK) >> EMC_NFERR_MASK_BIT;
+					rs_correct(tmpbuf, index, mask);
+					/* FALL-THROUGH */
+				case 3:
+					index = (REG_EMC_NFERR2 & EMC_NFERR_INDEX_MASK) >> EMC_NFERR_INDEX_BIT;
+					mask = (REG_EMC_NFERR2 & EMC_NFERR_MASK_MASK) >> EMC_NFERR_MASK_BIT;
+					rs_correct(tmpbuf, index, mask);
+					/* FALL-THROUGH */
+				case 2:
+					index = (REG_EMC_NFERR1 & EMC_NFERR_INDEX_MASK) >> EMC_NFERR_INDEX_BIT;
+					mask = (REG_EMC_NFERR1 & EMC_NFERR_MASK_MASK) >> EMC_NFERR_MASK_BIT;
+					rs_correct(tmpbuf, index, mask);
+					/* FALL-THROUGH */
+				case 1:
+					index = (REG_EMC_NFERR0 & EMC_NFERR_INDEX_MASK) >> EMC_NFERR_INDEX_BIT;
+					mask = (REG_EMC_NFERR0 & EMC_NFERR_MASK_MASK) >> EMC_NFERR_MASK_BIT;
+					rs_correct(tmpbuf, index, mask);
+					break;
+				default:
+					break;
+				}
+			}
+		}
+
+		tmpbuf += ECC_BLOCK;
+	}
+
+	return 0;
+}
+
+#ifndef CONFIG_SYS_NAND_BADBLOCK_PAGE
+#define CONFIG_SYS_NAND_BADBLOCK_PAGE 0 /* NAND bad block was marked at this page in a block, starting from 0 */
+#endif
+
+static void nand_load(int offs, int uboot_size, uchar *dst)
+{
+	int page;
+	int pagecopy_count;
+
+	__nand_enable();
+
+	page = offs / page_size;
+	pagecopy_count = 0;
+	while (pagecopy_count < (uboot_size / page_size)) {
+		if (page % page_per_block == 0) {
+			nand_read_oob(page + CONFIG_SYS_NAND_BADBLOCK_PAGE, oob_buf, oob_size);
+			if (oob_buf[bad_block_pos] != 0xff) {
+				page += page_per_block;
+				/* Skip bad block */
+				continue;
+			}
+		}
+		/* Load this page to dst, do the ECC */
+		nand_read_page(page, dst, oob_buf);
+
+		dst += page_size;
+		page++;
+		pagecopy_count++;
+	}
+
+	__nand_disable();
+}
+
+static void jz_nand_init(void) {
+
+ 	/* Optimize the timing of nand */
+	REG_EMC_SMCR1 = 0x094c4400;
+}
+
+static void gpio_init(void)
+{
+	/*
+	 * Initialize SDRAM pins
+	 */
+#if defined(CONFIG_JZ4720)
+	__gpio_as_sdram_16bit_4720();
+#elif defined(CONFIG_JZ4725)
+	__gpio_as_sdram_16bit_4725();
+#else
+	__gpio_as_sdram_32bit();
+#endif
+
+	/*
+	 * Initialize UART0 pins
+	 */
+	__gpio_as_uart0();
+}
+
+static int is_usb_boot()
+{
+ 	int keyU = 0;
+
+ 	__gpio_as_input(KEY_U_IN);
+ 	__gpio_enable_pull(KEY_U_IN);
+
+ 	__gpio_as_output(KEY_U_OUT);
+ 	__gpio_clear_pin(KEY_U_OUT);
+
+ 	keyU = __gpio_get_pin(KEY_U_IN);
+
+ 	if (keyU)
+ 		serial_puts("[U] not pressed\n");
+ 	else
+ 		serial_puts("[U] pressed\n");
+
+	return !keyU;
+}
+
+void nand_boot(void)
+{
+	void (*uboot)(void);
+
+	/*
+	 * Init hardware
+	 */
+	jz_nand_init();
+	gpio_init();
+	serial_init();
+
+	serial_puts("\n\nNAND Secondary Program Loader\n\n");
+
+	pll_init();
+	sdram_init();
+
+#if defined(CONFIG_NANONOTE)
+	if(is_usb_boot()) {
+		serial_puts("enter USB BOOT mode\n");
+		usb_boot();
+	}
+#endif
+
+	page_size = CONFIG_SYS_NAND_PAGE_SIZE;
+	block_size = CONFIG_SYS_NAND_BLOCK_SIZE;
+	page_per_block = CONFIG_SYS_NAND_BLOCK_SIZE / CONFIG_SYS_NAND_PAGE_SIZE;
+	bad_block_pos = (page_size == 512) ? 5 : 0;
+	oob_size = page_size / 32;
+	ecc_count = page_size / ECC_BLOCK;
+
+	/*
+	 * Load U-Boot image from NAND into RAM
+	 */
+	nand_load(CONFIG_SYS_NAND_U_BOOT_OFFS, CONFIG_SYS_NAND_U_BOOT_SIZE,
+		  (uchar *)CONFIG_SYS_NAND_U_BOOT_DST);
+
+	uboot = (void (*)(void))CONFIG_SYS_NAND_U_BOOT_START;
+
+	serial_puts("Starting U-Boot ...\n");
+
+	/*
+	 * Flush caches
+	 */
+	flush_cache_all();
+
+	/*
+	 * Jump to U-Boot image
+	 */
+	(*uboot)();
+}

package/uboot-xburst/patches/005-i2c.patch

@@ -0,0 +1,13 @@
+diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile
+index ef32f13..4e234b4 100644
+--- a/drivers/i2c/Makefile
++++ b/drivers/i2c/Makefile
+@@ -36,6 +36,7 @@ COBJS-$(CONFIG_DRIVER_S3C24X0_I2C) += s3c24x0_i2c.o
+ COBJS-$(CONFIG_S3C44B0_I2C) += s3c44b0_i2c.o
+ COBJS-$(CONFIG_SOFT_I2C) += soft_i2c.o
+ COBJS-$(CONFIG_TSI108_I2C) += tsi108_i2c.o
++COBJS-$(CONFIG_JZSOC_I2C) += jz_i2c.o
+ 
+ COBJS	:= $(COBJS-y)
+ SRCS	:= $(COBJS:.o=.c)
+

package/uboot-xburst/patches/009-n516.patch

@@ -0,0 +1,23 @@
+diff --git a/Makefile b/Makefile
+index ed848f5..04cd32e 100644
+--- a/Makefile
++++ b/Makefile
+@@ -3448,6 +3448,18 @@ pavo_nand_config	:	unconfig
+ 	@echo "TEXT_BASE = 0x80100000" > $(obj)board/qi_lb60/config.tmp
+ 	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
+ 
++n516_config		: 	unconfig
++	@ >include/config.h
++	@echo "#define CONFIG_N516 1" >>include/config.h
++	@./mkconfig -a n516 mips mips n516
++
++n516_nand_config	:	unconfig
++	@echo "#define CONFIG_NAND_U_BOOT" > $(obj)include/config.h
++	@echo "Compile NAND boot image for n516"
++	@./mkconfig -a n516 mips mips n516
++	@echo "TEXT_BASE = 0x80100000" > $(obj)board/n516/config.tmp
++	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
++
+ #########################################################################
+ ## MIPS64 5Kc
+ #########################################################################

package/uboot-xburst/patches/010-sakc.patch

@@ -0,0 +1,32 @@
+diff --git a/Makefile b/Makefile
+index a318eb4..7d14b8b 100644
+--- a/Makefile
++++ b/Makefile
+@@ -3448,6 +3448,13 @@ qi_lb60_config	: unconfig
+ 	@echo "TEXT_BASE = 0x80100000" > $(obj)board/n516/config.tmp
+ 	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
+ 
++sakc_config	: unconfig
++	@echo "#define CONFIG_NAND_U_BOOT" > $(obj)include/config.h
++	@echo "Compile NAND boot image for SAKC"
++	@$(MKCONFIG) -a sakc mips mips sakc
++	@echo "TEXT_BASE = 0x80100000" > $(obj)board/sakc/config.tmp
++	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
++
+ #########################################################################
+ ## MIPS64 5Kc
+ #########################################################################
+diff --git a/cpu/mips/Makefile b/cpu/mips/Makefile
+index 33afb66..a177653 100644
+--- a/cpu/mips/Makefile
++++ b/cpu/mips/Makefile
+@@ -35,7 +35,7 @@ COBJS-$(CONFIG_PURPLE)	+= asc_serial.o
+ COBJS-$(CONFIG_JZSOC) += jz_serial.o jz_i2c.o jz_mmc.o
+ COBJS-$(CONFIG_JZ4740) += jz4740.o jz4740_nand.o
+ COBJS-$(CONFIG_NANONOTE) += nanonote_gpm940b0.o
+-
++COBJS-$(CONFIG_SAKC) += nanonote_gpm940b0.o
+ 
+ SRCS	:= $(START:.o=.S) $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
+ OBJS	:= $(addprefix $(obj),$(SOBJS-y) $(COBJS-y))
+