It was originally tristate, but was changed to bool to prevent a build
breakage in an earlier patch revision (for a new syscall). The actual
commit[1] changed it in a way this isn't needed anymore, but
accidentially left the EXPORTFS change in. There's no reason for it
not being buildable as a module, so changing it back to tristate is
fine.
see: https://patchwork.kernel.org/patch/812832/
Thank you Jonas Gorski for the patch.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27011 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Add missing config symbols
* Update package/kernel for 2.6.39
CONFIG_BT_L2CAP=y and CONFIG_BT_SCO=y are set to build them into the bluetooth module.
Thank you Jonas Gorski for the patch
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27010 3c298f89-4303-0410-b956-a3cf2f4a3e73
* add md5sum for kernel
* add some missing config symbols
* add some ssb patches to make compat-wireless compile
Thank you Peter Wagner for the patch
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27009 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes for the following warnings:
drivers/mtd/devices/block2mtd.c: In function '_open_bdev':
drivers/mtd/devices/block2mtd.c:272:3: warning: ISO C90 forbids mixed declarations and code
drivers/mtd/devices/block2mtd.c: In function 'add_device':
drivers/mtd/devices/block2mtd.c:399:13: warning: assignment discards qualifiers from pointer target type
In the case of 442-block2mtd_probe.patch, it's not until the insertion of a executable statement before the definition that causes a warning, so I've chosen to resolve the issue here by splitting the definition and the initialization into a definition and a statement (and assignment) instead.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27007 3c298f89-4303-0410-b956-a3cf2f4a3e73
The flash driver code should be cleaned up and the broad detection code should be placed into arch code and used here.
This fixes#9323
Thank you Will Holmes for the patch.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27005 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for D-Link's DVA-G3810BN/TL product.
Signed-off-by: Roman Dumycz <roman@secureas.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26956 3c298f89-4303-0410-b956-a3cf2f4a3e73
* adds support for Artec Thincan
Signed-of-By: Lauri Võsandi <lauri.vosandi@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26919 3c298f89-4303-0410-b956-a3cf2f4a3e73
Thank you Peter Wagner for the patch. I refreshed the kernel patches and added the md5sum of the kernel.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26905 3c298f89-4303-0410-b956-a3cf2f4a3e73
Note that the Alix6 uses GPIO 27 to disable wireless transmit (W_DIS#), whereas on all other versions this is used to actuate the speaker.
GPIO 1 : SIM select (Alix6)
GPIO 6 : LED1
GPIO 25 : LED2
GPIO 27 : LED3 or RFKILL (Alix6)
GPIO 24 : Soft switch 1
No kernel version bump. Added i2c-scx200-acb for lm-sensors support.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26880 3c298f89-4303-0410-b956-a3cf2f4a3e73
Note that the Alix6 uses GPIO 27 to disable wireless transmit (W_DIS#), whereas on all other versions this is used to actuate the speaker.
GPIO 1 : SIM select (Alix6)
GPIO 6 : LED1
GPIO 25 : LED2
GPIO 27 : LED3 or RFKILL (Alix6)
GPIO 24 : Soft switch 1
No kernel version bump. Added i2c-scx200-acb for lm-sensors support.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26879 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add the required board definition, default config and image generation for
the T-Home Speedport W 303V Typ B.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26878 3c298f89-4303-0410-b956-a3cf2f4a3e73
Rename the DSL-274xB rev C2's board ID to "AW4139" to match the one used
for the rev C3 (same hardware) and add a fixup for C2. Also generate
images for C3.
While we are at it, rename the LEDs to conform to the Linux LED naming
conventions.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26876 3c298f89-4303-0410-b956-a3cf2f4a3e73
Make the fixup board ID independent from the image name to allow using
the same board ID for similar devices.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26874 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds 802.1Q VLAN support for the ADM6996M chip.
The driver is loaded for both the FC and M model. It will detect which of the
two chips is connected. The FC model is initialised, but no further
functionality is offered.
The PHY driver will always report "100 Mbit/s, link up", for both the M and FC
models. This reflects the fact that the link between switch chip and Ethernet
MAC is always on[1].
Further documentation can be found in the kernel's
Documentation/networking/adm6996.txt
Signed-of-By: Peter Lebbing <peter@digitalbrains.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26865 3c298f89-4303-0410-b956-a3cf2f4a3e73
The function __devinit ag71xx_probe() references
a function __devexit ag71xx_phy_disconnect().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
ag71xx_phy_disconnect() so it may be used outside an exit section.
The function ag71xx_phy_disconnect() references a function in an exit
section.
Often the function ag71xx_ar7240_cleanup() has valid usage outside the
exit section
and the fix is to remove the __devexit annotation of
ag71xx_ar7240_cleanup.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26855 3c298f89-4303-0410-b956-a3cf2f4a3e73
The via-sata and gpio-nsc modules are both unneeded on the Geos platform.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26811 3c298f89-4303-0410-b956-a3cf2f4a3e73
If there is no sprom on an ssb based pci device on the brcm47xx
architecture ssb now asks the architecture code to look into the nvram
to get some sprom data for this device. Now we are able to read out
pci/1/1/ foo or pci/1/3/ foo config options.
This will fix some problems where the wireless devices does not got an
mac address and the following message was show:
ssb: WARNING: Invalid SPROM CRC (corrupt SPROM)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26801 3c298f89-4303-0410-b956-a3cf2f4a3e73
SPIN_LOCK_UNLOCKED has been deprecated since 2.6.19 and will get removed
in 2.6.39, so replace it with DEFINE_SPINLOCK().
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26770 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use offset from struct mtd_part instead of struct mtd_partition for defining
the new partitions. This enables the usage of MTDPART_OFS_APPEND macro in
struct mtd_partition.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26705 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes a bug that led to ECN enabled flows being de-prioritized by pfifo_fast
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26687 3c298f89-4303-0410-b956-a3cf2f4a3e73
Dual image capable CFEs store an image sequence at the same place as
currently OpenWrt stores the actual rootfs length, so it will get
overwritten when flashing through such a CFE.
To prevent this from happening, move the rootfs length field to the next
four bytes, thus completely using the reserved1 field.
Since the reserved1 field is now completely in use, it does not make sense
to allow it to be set from the imagetag utility, so remove the option.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26680 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add the PC speaker back to the Geos platform.
Add DMI support in BIOS.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26678 3c298f89-4303-0410-b956-a3cf2f4a3e73
