This defines the Geos platform from Traverse Technologies in AUS.
This is a Geode LX800 with 512MB of DDR400 memory, 2 8139CP interfaces, 2 Solos ADSL2+ interfaces, USB, serial console, CF slot, and miniPCI slot.
I'll add support for the LEDs separately.
Signed-off-by: Philip A. Prindeville
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23390 3c298f89-4303-0410-b956-a3cf2f4a3e73
Taking the ramips ethernet interface down and up again resulted in the
driver not receiving any frames anymore. Fix this by correctly disabling
interrupts in the hw on ifdown.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23243 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for Iomega iConnect Wireless. Leds and wireless card
support are still missing.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23217 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch-by: Cezary Jackiewicz <cezary@eko.one.pl>
(the GPIODEV code has been removed, the sysfs interface
can be used to control the GPIO lines instead - juhosg)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23165 3c298f89-4303-0410-b956-a3cf2f4a3e73
LAN (eth0) is behind a switch and the fixed speed/duplex was
supposed to be for it, not WAN (eth1).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23147 3c298f89-4303-0410-b956-a3cf2f4a3e73
With this change ath9k can handle the wireless chip on the TL-WR841N v7
board which is based on the AR7241 SoC.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23130 3c298f89-4303-0410-b956-a3cf2f4a3e73
The attached patch adds a preliminary support for Prolink PWH2004 board
(Ralink RT305x based). LAN and flash appear to work. However, the USB
port and WLAN I have not managed to activate properly yet, but that
problem appears to be present with other rt305x targets as well(?).
Signed-off-by: Esa Hyytia <esa at netlab.tkk.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23129 3c298f89-4303-0410-b956-a3cf2f4a3e73
The current defaults for ramips rt305x does not allow the USB
subsystem to be selected/built.
This patch is just a small step in that direction.
Signed-off-by: Luis Correia <luis.f.correia@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23128 3c298f89-4303-0410-b956-a3cf2f4a3e73
The RTL8366S/RB support connecting a second mac to it and using the 5th
port as an independent phy. Therefore we need to handle autonegotiation
changes for phy 4 like on a single phy device.
This fixes#7980, verified on a WNDR3700.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23127 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is still preliminary and not really tested much. Anyway, this
version seems to be enough to get both wired and wireless
interfaces working. Buttons and leds are also working.
mach-ap96.c is based on mach-wndr3700.c.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23125 3c298f89-4303-0410-b956-a3cf2f4a3e73
